Search Documents

By C. R. Kuzell

INTRODUCTION KNOWLEDGE of the thermal capacity of gases is of great importance in making metallurgical calculations. The metallurgist is, frequently called upon to investigate and determine furnace efficiencies in which the heat carried into or out of the furnace by gases is a large item in the heat balance. Not only do such problems present themselves in the determination of furnace efficiency, but also in the study of the application of heat is accessory apparatus, such as stoves, regenerators, waste-heat boilers, driers,.etc. The thermal effect of the use of excess air in the combustion of fuel, the theoretical temperatures of combustion, the quantity of heat in hot blast at various temperatures, the effect of hot blast on furnace temperatures, are a few more examples of frequently occurring calorific problems involving gases. So many are the applications of the data on the heat capacity of gases that the subject merits careful study. The heat in a gas maybe due to its heat of combustion, if it is a combustible gas, and to its temperature. The latter is called its sensible heat and is the heat absorbed or evolved by a gas as its temperature is raised or lowered. The heat of combustion of gases is well established and is commonly known. The values can be found in almost any mcdern treatise on metallurgy. The sensible heat of gases has not been so well established because it is in most cases a function of the temperature, and the values of specific heats of gases over a wide range of temperatures have only recently been determined. It is the purpose of this paper to deal with the sensible heat of gases.

Jan 8, 1914

By C. S. Parsons

Custom milling-plants have been operated successfully for a great many years on this continent. One of the outstanding examples in the United States is the Golden Cycle mill at Colorado Springs, which mills the gold-telluride ores from the Cripple Creek district. In eastern Canada, the Northern Custom Concentrators, Limited, at Cobalt, successfully treated the cobalt-silver ores of that area for a number of years. Flotation plants have entered the custom field in the past few years. The building of flotation concentrators to treat ores on a custom basis indicates the advance which has been made in flotation. In fact, three years ago it was considered almost impossible to treat successfully a mixture of miscellaneous ores by flotation. The methods used at that time were considered so delicate that any change, even in a single ore, would usually result in decreasing the effectiveness of the separation. Today we find four large custom flotation plants in the United States and one in Canada for treating complex lead-zinc ores from many different localities. The advent of these mills was brought about by the serious problem confronting the lead-smelting plants due to increasing amounts of zinc in the ores presented for treatment. It was necessary to penalize the mines shipping high-zinc ores. The penalty is justified, because high zinc in the lead blast-furnace charge not only decreases the tonnage of the furnace but increases the amount of flux necessary, as well as increasing the metal loss in the slag. It has been estimated that in the Salt Lake valley alone, 75,000,000 pounds of zinc was lost in the slag-dumps from the operations of three large lead blast-furnace plants. It has also been estimated that $150,000 worth of additional flux was required to slag this zinc. It was to avoid at least a part of this wste and to help maintain an ore supply that custom flotation concentrators were built by the smelters.

Jan 1, 1928

By Michael T. McCaffrey

The wide range of potential feed materials, process steps, and products in metallurgical facilities means that standard equipment might not be available to adequately meet the project technical and economic needs. Custom designed equipment should be considered only after rigorous research precludes purchasing standard equipment. However, the decision to use custom equipment introduces a new element of risk into the project. To manage the risk, custom equipment design should be developed through the same front end loading (FEL) phases as project development. If more than incremental development of custom equipment is required, appropriate test work or pilot trials are required to test key uncertainties. Important activities during custom equipment design include maintaining clearly defined performance objectives, conducting appropriate reviews, carefully crafting commercial and intellectual property agreements with design and fabrication partners, and assembling a multidisciplinary team with sufficient development expertise.

Jan 1, 2015

By R. B. Hopler

Explosives R&D has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. This process continues at an accelerated pace today due to the tools presently available to the explosives and mining industries.

Jan 1, 1993

By J. David Chapman

There are a variety of choices of materials for mineral extraction processing. Traditionally, end users have used metallic piping for fluid handling and little is known about the advantages (or limitations) of non-metallic piping systems. This presentation will review custom FRP pipe systems and their use in severe corrosive and erosive process streams. These systems can be designed to various pressure and temperature ratings and different components (such as resin and glass type) can be varied to suit the process conditions

As Coal Mining Areas develop, problems relating to strata control increase. The "easy" coal has been extracted and the future development lies in the direction of greater depths of cover and more difficult strata conditions. To provide solutions to the problems encountered the techniques of constructing and testing physical models have been developed and refined. With a sound knowledge of model theory allied to practical experience, mining research engineers use physical cemented material models to examine, assess and solve mining problems relateu to strata behaviour and environment. For a model to provide the answer to a particular mining problem it is essential that as much information as possible be obtained from the mine or area of a mine which the model is to represent. Details relating to the strata, geological malformations, and the stress environment must be collected and collated to ensure reliable results.

Jan 1, 1976

By Frank Barker

Mining operations present a very different environment to the suppliers of explosives, initiating systems and services, both on surface and underground. Typical hazards include underground movement, air quality, ground stability, moving equipment, and the use of explosives. As contractors to the mining industry we do not have management control over the environment in which our people operate. The hazards and consequent level of risk that our people are exposed to in some mining operations are significantly higher by orders of magnitude than in a normal factory environment. Orica Explosives (and other Explosives suppliers) are continually and increasingly identifying opportunities to partner with customers by adding value through the provision of services leading to a reduction in total mining costs. These services include the provision of a bulk underground loading services, delivery of product into underground magazines, magazine management, value added blasting, conversions, rock-on-ground contracts, and blast management programs.

Jan 1, 2000

By Franz Kolmbauer

At Primetals Technologies Brazil Ltda. Rio de Janeiro Santa Cruz Workshop we electroplate mold coppers for continuous casting by tank plating. Tank plating submerges the copper in the bath of the plating solution. This is the most common method of plating and is applicable for both broadface and narrowface copper plates. Mold copper plates have a decisive impact on the product quality as well as the cost for maintenance and production. A perfect understanding of the operational influences on the plates and performance variables are the first step for the right selection of a copper plating method. Variable Hiper Coat keeps the Copper Plates 50% up to 100% longer in operation because of applying hardness on the Copper Plate where it is needed. Primetals Technologies Brazil provides the solution which meets and exceeds the requirements for todays and future demands.

Aug 16, 2017

By Daniel Hack

A few progressive mining software companies have recognized the benefit of broadening their capabilities to the sand and gravel (aggregate) industry. The most promising new developments have been designed for use with Surpac Vision, one of the world’s leading geological modeling, mine design, and production management systems. Surpac’s broad user-base, who have always had a propensity for customization, are now focusing on development of solutions in the Tool Command Language (Tcl), an interpreted scripting language. Surpac Software International made changes to TCL to add Surpac specific extensions, thus creating the Surpac Command Language (Scl). The Tcl interpreter, including Scl extensions, is bound into the Vision executable to provide a seamless interface to the data objects used internally by Vision, the GUI, and the 3D rendering system. Custom solutions can be incorporated as Vision extensions, or as stand alone-modules used in correlation with modeling, design, and planning functions.

Aug 25, 2002

Narrow vein mining, with enough challenge and also where the cutting edge technology can be applied, is still a very important and exciting portion of the mining industry. Based on the deposit characteristics, the most flexible mining method, cut and fill, has been being tested mining this high grade Northern Nevada property, Hollister, since the year of 2008. In the last three years, 254,000 tons of ore were hauled out of the portal and 23,000 feet of development were excavated underground with the winning of several safety and environmental awards. Together with mine geology, the essential segments include mining cycle, ground control, ventilation, grade control and backfill method in cut and fill stopes were covered in this paper.

Jan 1, 2012

By Sebastián H. Troncoso

Open pit mine planning is normally based on the selection of an economic envelope that has been generated by the Lerchs & Grossman algorithm, which requires individual economic valuation of each block of a geological block model. The selected envelope, usually called Final Pit, is later discretized in pushbacks and benches, which correspond finally to the fractions that the production schedule will allocate in time. This planning methodology has been widely used by the mining industry in countless projects to exploit open-pit mines, however, in many of the deposits can be found some undesirable elements such as arsenic, phosphates, ash among others that tend to reduce the value of elements of economic interest, either by disrupting the processes of concentration or as deemed impurities that affect the quality of the final product. Thus, a fair amount of blending would be required to capture the real value of the ore body. The traditional approach under estimates a block value by penalizing the block value by the amount of contaminant even when at the mine a set of blocks is amine at a time. This paper proposes a methodology for computing cut off grades over time that would maximize net present value allowing blending that should fulfill a set of metallurgical constraints. Preliminary results show significant increases in value and reserves quantity, questioning the use of fixed cut-off grades in generating a production schedule when blending applies to fulfill a set of geometallurgical constraints. Finally, the model allows the authors to show the importance of having adequate planning tools that will lead to the ability to look at the potential economic value of a mineral deposit.

Oct 1, 2009

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.'s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982

By B. Hornsby

At the Mount Isa mine, Mount Isa, Qld., Australia, sublevel open-stope mining is used for copper ore while both sublevel open-stope and cut-and-fill methods are used for the silver-lead-zinc ores. Production in 1979¬80 was 4 730 000 t (5,200,000 st) copper ore and 2 590 000 t (2,850,000 st) of lead ore. The deepest mine level currently is 960 m below the surface. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The mine is located in the valley of the Leichhardt River in Lower Proterozoic sediments of the Mount Isa group. The regional strike of the sediments is north¬south and they have a persistent westerly dip of about 1.1 rad (65°). In the mine area, the Mount Isa group comprises a sequence of alternating bands of dolomitic shales and siltstones some 3.2 km (2 miles) in width. It is bounded on the east by greenstones and quartzose sediments of the Eastern Creek volcanics, and on the west by the Mount Isa fault, west of which occur schists and other metamorphic rocks. The ore bodies as currently known at Mount Isa are restricted to the Urquhart shale, a formation of thinly bedded pyritic, dolomitic, and volcanic shales some 1070 m (3500 ft) thick. Towards the top of the Mount Isa group sediments, copper and silver-lead-zinc ore bod¬ies occur as contiguous but discrete entities and are mined and treated separately (see Figs. I and 2). Argentiferous galena, sphalerite, pyrite, and minor associated sulfides occur in distinct concordant bands throughout the Urquhart shales. Wherever these bands are grouped together in sufficient density they constitute silver-lead-zinc ore bodies with widths varying up to 36.6 m (120 ft). Other mineralized bands are common in intervening beds. Individual ore bodies persist for many hundreds of meters concordant with the strike and dip of the enclosing shales. Intersections of these beds with fold axes provide local zones of enrichment but otherwise the mineral content of the ore bodies varies only slightly throughout the extent of the dip and strike. Chalcopyrite is the only important primary copper mineral. It occurs in association with pyrite and pyrrhotite as disseminated flocks and as vein fillings throughout irregularly shaped zones of folded, brecciated, and re¬crystallized Urquhart shale. These zones, which are lo¬cally termed "silica-dolomite" bodies, are broadly transgressive to the shale bedding and confine all significant copper mineralization to the virtual exclusion of silver¬lead-zinc mineralization. In some areas, the downward percolation of acidic water through faults and shears has caused extensive leaching of the coarse-grained carbon¬ates to depths in excess of 610 m (2000 ft), but most of the silica-dolomite remains unleached and the ground is competent. The majority of lead ore being mined is north of the main shaft pillar (R62, U62) area. The major lead¬producing areas for many years have been the Black Star ore bodies (2 and 5 ore bodies) and the Racecourse ore

Jan 1, 1982

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By Gordon Miner

GENERAL DESCRIPTION At the Star mine, Hecla Mining Co., located in Burke, Shoshone County, ID, the mining method is horizontal slicing (timbered or untimbered) cut-and-fill using hydraulic sand backfill. Back stoping as well as breast stoping is used; see Fig. 1. The annual produc¬tion from all cut-and-fill mining is 259 816 t (286,400 st). The average depth ranges from 366 to 2408 m (1200 to 7900 ft). A majority of the tonnage comes from an average depth of 2240 m (7350 ft). Average travel time to the stope is 1 hr. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size and Ground Conditions The ore body is 610 to 1219 m (2000 to 4000 ft) along the strike and 2408 m (7900 ft) on the dip, with an average vein width of 2.6 m (8.5 ft). The dip is essentially vertical. The ore body is heavily sheared and broken on the main fault structures; it is more competent on the wall veins but everywhere subject to rock bursting at depth. The hanging and footwalls are strongly fractured on the main fault structures, again more competent but still fractured on the wall veins. All host rock is Revett quartzite. Value and Production Requirements The ore value is $56 per ton. Production require¬ments are 1089 t/ d (1200 stpd), five days per week. Why Cut-and-Fill? The slusher extraction method is the most satisfac¬tory and practical for narrow vertical veins with sheared walls. The method must be quite selective to be com¬mercial. The veins are too narrow for rubber-tired ex¬traction and the grade is not high enough to make resuing practical. DETAILED DESCRIPTION Development Access to the main shaft is by the 3.2-km (2-mile) main haulage tunnel. The level intervals in the vertical timbered shafts are 61 m (200 ft). Vein development is by crosscut and laterals located 30.5 m (100 ft) into the vein wall. Vein crosscuts are on ±61 m (200 ft) centers. Access to the vein is by raises carried up with the stope. The raises are equipped with four wood¬cribbed chutes (two orepasses reinforced with angle irons, one manway, and one timber slide, Figs. 2-6). The initial cut is located 6.7 m (22 ft) above the main level (Fig. 1). Stoping Cycle Detail Sampling: Grab samples are taken from the mine cars. Channel sampling of the faces and backs is done when necessary. Drilling: For stope drilling, Ingersoll-Rand 300M percussion drills are used, with Ingersoll-Rand 300M and Gardner-Denver RB83M stopers, used for back stoping. Breasting down is done with Gardner-Denver S83FM jacklegs. The back stoping rounds are 0.9 to 1.8 m (3 to 6 ft) and the breast stoping rounds 1.5 to 3m (5 to 10 ft). Blasting: For stope blasting DuPont Tovex 100 watergel with fuses and igniter cord is used primarily. Approximately 60% of the blasting is done with am¬monium nitrate-fuel oil (ANFO). For development headings and shaft sinking, DuPont Drivex watergel with Ensign Bickford Nonel Primadet primers is is used. Mucking: Broken ore is removed entirely by slusher in the stopes. These are mostly 3.7-7.5-kW (5-10-hp) Ingersoll-Rand air-powered or 7.5-37.3-kW (10-50-hp) Ingersoll-Rand electric-powered. In the horizontal de¬velopment headings Eimco 12B and 21 and Atlas Copco LM-56 overshot mucking machines and a 0.76 (1 cu yd) hydroelectric Wagner HST-1 LHD (load-haul-dump) unit are used. Rockway for Extraction: The cribbed chutes (Fig. 7) are nearly vertical and hexagonal in shape and are made of spaced 152 x 203-mm (6 x 8-in.) timber, reinforced with varying weights and sizes of angle iron, depending on wear requirements. Rectangular cribbed chutes are used where ground pressure is not a problem. Cribbing is added in 2.4 or 3-m (8 or 10-ft) extensions accord¬ing to the floor height (whether timbered or untimbered). See Figs. 8 and 9. Backfilling: Backfilling is done with hydraulic sand consisting of classified mill tailings at 65% solids. The fill contains approximately 20% 325-mesh fines. The tailings are pumped 3353 m (11,000 ft) at 50-55% solids 22.7 dry t/h (25 dry stph) with a duplex piston pump. Cycloning increases the tailings density to 65% solids. Fill storage is in a 998-dry-t (1100 dry st) agi

Jan 1, 1982

Work undertaken in the field of cut-off grade optimization has not advanced much beyond the work undertaken by Lane in 1988. His definitive work is based on the calculus of the Net Present Value criterion which is the most widely understood, consistent, and appropriate method by which sequential cash flows arising from the extraction of mineral reserves from an exhaustible resource can be represented. Although the mathematics is not complex Lane’s method is not a widely appreciated or applied approach to maximizing the value of a mining operation through selection and balancing of operational cut-off grades. Three stages in a mining operation namely, mining, processing and marketing were defined by Lane and the economics of each stage are identified and isolated to provide an optimum cut-off for each stage. Points of intersection along the present value curves for each stage of a mining operation are used to identify balancing cut-off grades at points where the capacity of the mining, processing and marketing stages is fully utilized and the Net Present Value of the operation is optimized. Data that simulate a small, deep-level Witwatersrand-type gold mine with an average grade of 6 g/t Au and a logrithmic variance of 1.2,are applied to the model to illustrate the benefits of representing cut-off grades in terms of present value curves for different segments of a mining operation. Keywords: Cut-off grade, Net Present Value, grade-tonnage curve, balancing cut-off grade, mining, processing, marketing.

Jan 1, 2003

By M W. N Buxton, M T. Bootsma, J Benndorf, C Alford

Research in the field of cut-off grade optimisation has shown a relationship between cut-off grade, project life and net present value (NPV). Lane’s theory demonstrates that cut-off grades can be optimised in order to maximise project profitability. Although the theory forms the basis for many open pit mining projects, application of the theory in underground mining remains limited to-date. The main reason for this is the complex interaction between all processes in underground mine planning, which makes it difficult to apply Lane’s mathematical optimisation approach.Recently a new stope optimiser product was released. The AMS Stope Optimiser automates the design of underground stopes at user-defined cut-off grades and allows for rapid evaluation of mine designs at different cut-off grades. Using this software, an optimisation approach was developed and validated on an underground gold deposit in northern Sweden. Potential project NPV increased by approximately 30 per cent when using this new approach.Spatial grade uncertainty in mineral resources was identified to be a major risk in underground stope design. The optimisation approach was further extended to account for grade risk using estimated and stochastic simulated resource models. The resulting optimisation process accounts for grade risk early in the design process and reduces the risk of a stope not meeting the cut-off grade with subsequent financial loss.CITATION:Bootsma, M T, Alford, C, Benndorf, J and Buxton, M W N, 2014. Cut-off grade-based sublevel stope mine optimisation – introduction and evaluation of an optimisation approach and method for grade risk quantification, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 281–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Michel Dagbert

"This paper illustrates the different ways grade-tonnage curves can be generated f or a mineral deposit. It emphasizes systematic discrepancies between reality, estimates and actual production according to different estimation methods and grade control programs. It does not offer a universal solution to the prediction of grade-tonnage curves. Hopefully, it will inspire caution to mineral economists who use estimated grade and tonnage data in the establishment of an optimum cut-off grade for a mining operation.IntroductionThe value of a mineral development venture often depends on a grade-tonnage curve. Statistics can help. The idea is to divide mentally the orebody into small blocks called selective mining units or SMUs. A SMU is an idealized version of the quantity of rock the grade of which will be tested against the cut-off at the time of mining. It could be as small as a truck load or a shovel load in very selective operations like some uranium mines where radiometric probing of each truck or car is performed. More typically, in an open pit operation, it will be the smallest zone flagged as ore from blast hole data, e.g. a 5 m by 5 m by 10m block, if blast holes are on a 5 m grid and bench height is 10m. Having defined the SMUs, the grade-tonnage curve determination amounts to evaluating the grade distribution of all the SMUs that can be mined in the depo sit. If we know this distribution we simply apply the cut-off to it and we get the number of SMUs above the cut-off (i.e. ore tonnage) and their average grade. .Assessment of the grade distribution of SMUs from exploration drill hole data is not an easy exercise and much has been published on the subject (David, 1972; Marechal , 1972; Huijbregts, 1975; Marechal, 1975; Guibal and Touffait, 1982). In this paper, we use a gold mine example to illustrate the influence of SMU size on the results. With the same example we also show that ""common-sense"" methods of grade-tonnage curve determination can sometimes be misleading."

Jan 1, 1987

By Wolfgang G. Brunner

A 3800 m long temporary water-retaining dike has been constructed under extreme conditions in the harsh northern climate to enable two of the kimberiite pipes at the Diavik Diamond Project reserve to be mined using open pits. The Diavik Diamond Project is located on East Island at Lac de Gras in Canada's Northwest Territories, approximately 200 kilometres south of the Arctic Circle. The dike which has been constructed in up to 25 m deep water from crushed granite quarried from the site projects into Lac de Gras encircles the first two of the kimberiite pipes to be mined. An 800 mm wide diaphragm cut­off wall constructed of bentonite, cement and crushed rock, totalling 33,000 m2, and a two-phase jet grouted curtain wail at its base, totalling 8,400 m2, have been installed through the dike and underlying till foundation into bedrock. The cut-off is designed to minimise water seepage from Lac de Gras through the dike. In order to ensure that the dike had adequate internal stability and diaphragm wall construction could proceed safely, the crushed rock fill material dumped into the lake was first compacted by TR 75 deep vibrators. In 2000, Bauer Maschinen GmbH of Schrobenhausen, Germany were awarded the contract for the supply of all specialist foundation equipment required on site and for providing technical support to the Canadian main contractor Lac-de-Gras-Construction throughout the construction of the cut-off walls during 2001 and 2002. Installation of the cut-off walls was completed in July 2002, three weeks ahead of schedule, and dewatering of the inner dike areas commenced just 5 days later and has continued throughout August and September. After completion of extensive testing of the diamond recovery plant, the mine is scheduled to go into full open pit production in February 2003.

Jan 1, 2003

By I. D. Dayal, Anil Kumar Jain

"Cutoff walls are frequently used to slow down or prevent seepage of water through and/or around dams. Cutoff wall is a type of seepage barrier structure designed to reduce the flow of water underneath temporary or main dam. There are number of techniques for the construction of cutoff walls including concrete, Jet grouting and permeation grouting. NHPC LTD, a premier Govt. of India undertaking has been instrumental in the hydropower development within the country & in nearby countries like Nepal & Bhutan since last four decades. NHPC LTD has completed more than 20 hydro-electric projects with total installed capacity of 6587MW (including capacity addition by JV- NHDC). In all these projects, different types of dams and spillways were constructed in not so benign to extreme challenging geological set up. There has always been challenge associated with the temporary diversion works. The project sites sometimes incur huge river bed excavations in case of concrete gravity dam founded on rock foundation at large depth. The challenges for minimizing the seepage have been well taken care by constructing the dedicated seepage barriers. The construction of cut-off walls have progressed from “conventional continuous trench backfilled with conventional concrete or plastic concrete” to “grout curtain”, to “jet grouting” to the “concrete cut-off wall” , the last being the most sophisticated & credible seepage barrier.The efficiency of the cut-off walls are monitored by the seepage quantity observed (reduction of the seepage flow), uplift pressures or exit gradients after construction of cut-off walls. For construction of the main concrete dam, required space is created by the river bed excavation for placing the dam foundation on sound rock. Sometimes there is deep river bed excavation from 30 to 40 m depth or even more as per the available rock profile. Temporary coffer dams are constructed for diverting the river flow through diversion tunnels / channels etc. In deep river bed excavation; there are high chances of the significant seepage through the coffer dam foundation / river bed material due to high hydraulic gradients. Seepage and piping are the main causes of the failure / damage of the temporary coffer dams. If the seepage quantity is too high, then it becomes difficult to handle it by dewatering in the dam pit. Dam concrete is required to be placed unhindered to have a monolithic construction of dam blocks & to have faster construction in the working season. Cut-off walls increase the seepage path considerably thus reducing the exit gradient and further reduction of the seepage thus helping in maintaining the seepage free area for working."

Jan 1, 2016