Search Documents

By William E. Torres

The Southern Peru Limited smelter, in Ilo, operates two reverberatory furnaces, seven Peirce-Smith converters, one Teniente Converter, two casting wheels and a single contact acid plant. The Teniente Converter was commissioned in August 1995 and was designed to smelt 744 dry metric tons (820 dry short tons) of concentrate per day. The process off-gas is collected in a water-cooled hood, cooled in a spray chamber, and cleaned in a Joy electrostatic precipitator for further treatment in the Acid Plant. This paper presents the current Teniente Converter operating practices and control philosophy. Relevant improvements and modifications to achieve a 379 day campaign without tuyere replacement and a daily average smelting rate of 862 dry metric tons (940 dry short tons) of concentrate are discussed.

Jan 1, 1998

By L. Gilbert

Recent changes to environmental legislation and trends in the environmental regulation of mining in the Northern Territory are being driven by (among other factors) Federal Government policies and international agreements on the environment. These trends are discussed and the expected application of the NT Water Quality Management Strategy (based on the National Water Quality Objectives) over the next few years is examined with respect to mine environmental management practices. Some of the potential conflicts and changes in approach which may develop are identified and examples discussed. Proactive means of integrating trends in environmental legislation with mine planning and waste management are discussed.

Jan 1, 1994

By Smith I. T

Mine operators have long recognised that the results achieved in primary blasting are critical to subsequent mining activities. With the introduction of "in the hole" drills under- ground and the advantages offered by the use of water gels in conjunction with ammonium nitrate-fuel oil (ANFO) explosives, new mining methods have been developed and enabled improvements in older methods. Pumpable water gels have been used with varying success underground. These gels allow a high loading density even in ragged bore- holes. The problems encountered with slumping in upholes is recognised so the current trend is to use these gels in downholes where wet holes are prevalent. Cartridged water gel technology has advanced to the point where it has allowed the replacement of nitroglycerin (NG) based explosives and pumpable water gels. Today, gels can be made as a tampable product for use in development headings or as a slump- ing product for downholes to give an effective coupling. With the introduction of the Tovex« pneumatic loaders, the problems associated with a pumpable gel were eliminated and gave the user the ability to alter his loading density.

Jan 1, 1977

By R. B. Throndycraft

"1. Belt-Drop Agglomeration Preferred at Heap Leach Operations. The agglomeration method now preferred at heap leach operations utilizes belt-drops along conveyors. Belt-drop agglomeration is being designed into numerous upcoming heap leach operations. It offers substantial capital cost savings over previously favored drum agglomerators. It has such significant operating and maintenance advantages that some drum agglomerators have been retired in favor of belt-drops.The majority of heap leach operations are now built with crushing included in the flowsheet. If crushing is included, belt-drop agglomeration can be added for almost no cost. The agglomeration equipment is simply a few conveyor transfers, designed to provide the tumbling and rolling action which forms the agglomerates. Controlled water sprays are needed at each of these agglomeration transfers. Cement or lime is added as a binder, to stabilize the agglomerates. This reagent is also needed to raise pH to safe operating levels.Addition of the pH control reagent before stacking the ore offers a reagent cost benefit. In the belt-drop mixing technique, the ore is intimately mixed with the lime (or cement). After stacking on the heaps, when the cyanide solution is sprayed onto the high-ph ore, very little cyanide is consumed. Without the pre-addition of lime or cement, the leach solution is sprayed onto neutral ore. The mixture of high-pH leach solution and neutral pH ore causes the solution pH to drop, releasing cyanide gas. This release is minor from a safety viewpoint, much less than dangerous, but the gas release is a costly waste of the cyanide reagent. Pilot-scale comparison tests were made at Pinson. Ore pre-treated with lime or cement showed 30% less cyanide consumption than untreated ore."

Jan 1, 1989

Ground falls (roof and rib) have historically been responsible for nearly 50% of all fatalities in bituminous underground coal mines. In recent years, the number of some annual ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, the twin disasters at Crandall Canyon in 2007, in which nine miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990s, these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents since 2005. Progress has also been made in pillar recovery, where there has been just one fatal incident since 2005. On the other hand, more than 300 miners continue to be injured each year by rock falling from between supports and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities available technologies such as roof screen, rib bolting and inside control roof bolters could reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety.

Jan 1, 2011

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By V. H. Forsythe

Mr. Chairman, members of SME, and guests It is indeed a pleasure to have the opportunity to appear before this group. The topic of this paper is, "Current Trends in Related Industries and Their Influence on Electric Shovel Design and Size". Before getting into the major items, it is well to point out that this text will deal with loading shovels primarily, since their application is almost universal in major open pit mining operations throughout the world. Related industries influence our design in many ways. For the sake of simplicity, these industries will be broken down into two major categories. The first category to be discussed will include industries that will indirectly influence design and size, while the second category will include industries whose products can directly be incorporated by the engineer in the design of shovels.

Jan 1, 1964

By P. van der Westhuyzen

Gone are the days of stock-standard diamond beneficiation and final recovery circuits that could, with minor modifications, be adapted to treat any diamond-bearing ore source. A new era has dawned, offering the opportunity to streamline existing diamond processing operations or develop simpler, more efficient, and economical diamond processing plants, with the focus on more efficient comminution, beneficiation, and final recovery. This change in scene has been brought about by: ? The introduction, rapid development, and maturation of multiple comminution, sorting, and recovery technologies ? The need to adapt to a new standard of project approach post the commodity super-cycle phase, where optimizing existing operations and developing scalable, ?fit for purpose? new mines are fast becoming the norm in diamond processing plants in both primary and alluvial operations ? The quest for energy efficiency and lower labour costs ? More remote and inaccessible reserves (under lakes, tops of mountains etc.). This paper serves to identify some technology advances and demonstrates how these could be considered as replacements for or in combination with conventional technologies to arrive at an optimum techno-economic solution. To name a few applications/technologies: ? Comminution: conventional cone crusher, modified/specialized cone crusher, and the high-pressure grinding roll (HPGR). Although significant advances have been made in recent years, this paper only briefly covers comminution within the beneficiation circuit design ? Waste sorting: NIR (near-infrared) sorting, optical (colour) sorting, XRF (X-ray fluorescence) ? Primary concentration by combining dense media separation (DMS) with either XRT (X-ray transmissive), pulsed X-ray, jigs, or pan plants depending on the application, scale, and economics ? Final recovery of diamonds with either conventional X-ray technology, pulsed X-ray technology, or XRT. From recent studies, it can be concluded that there is no longer a standard solution, but rather the ?right? or appropriate solution. Through combining a sound knowledge of the ore source (ore dressing studies or onmine data gathering) and leveraging off the advances in technologies, one is able, through trade-off studies, to arrive at the ultimate techno-economic configuration, the ?right? solution. Emphasis is placed on maximizing diamond recoveries through appropriate technology selection and minimizing the associated costs in an effort to de-bottleneck or improve efficiencies of existing diamond processing plants, or to arrive at the ideal new diamond process plant design..

Jan 1, 2014

By G. Karahalios

Industrial minerals always play an important part in the technological growth of a country. The extraction and trading of industrial minerals continues to expand, but the industry is now subject to stricter environmental guidelines. This paper presents the current status and growth potential of industrial mineral exploitation in the southeastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, the Former Yugoslav Republic of Macedonia, Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. Annual production figures per country are presented for 1992-1998. These figures are compared to each other, and, where applicable, they are compared to world production figures. The marketing of industrial minerals to Europe and other regions of the world and the effects of such trade on the local economies are also evaluated when such data are available.

Jan 1, 2000

By G. Karahalios

Industrial minerals have always enjoyed an important share in the technological growth of any country in the world. Today, extraction and trading of industrial minerals has expanded, but is also subject to stricter environmental guidelines. This paper presents the current status as well as the growth potential in the exploitation of industrial minerals in the countries of the south eastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, F.Y.R.O.M., Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. More specifically, annual production figures per country are presented for1992-1998. These figures are compared to each other and, where applicable, to world production figures. Trading of industrial minerals from these countries to Europe and the world and its effect to the local economies is also evaluated were such data is available.

Jan 1, 2000

By Robert B. Parsons

"As the 1981 annual reports of Canadian mining companies one by one see the light of day, it becomes clear that softer metal prices and rising costs are the main problems which beset the industry today. These problems are certainly not lightened by that familiar monster lurking in the shadows-taxation! Recent taxation trends in Canada, and the existing tax regimes for the mining industry, continue to be a major bugaboo.This examination by ""Tax Notes"" of the impact of current taxation trends on the mining industry is based on a speech delivered recently by Robert D. Brown, senior tax partner of Price Waterhouse, Canada, to the annual meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers in Dallas.IntroductionThe purpose of this paper is to tell a story-and it is a story with a moral. The first thing to recognize is that, with depressed metal prices and weakening western economies, high taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. However, the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what the future holds for mining men in Canada will equally play an important role in the future development of the Canadian industry. Our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high marginal tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself."

Jan 1, 1982

By Robert D. Brown

The purpose of this paper is to tell a story - and it is a story with a moral. My topic is Present Trends in the Tax Environment Affecting Mineral Development in Canada, and the first thing to recognize is that, with depressed metal prices and weakening western economies, taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. But the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what taxes the industry will face in future years will influence the industry's further growth. My theme today is that, in Canada, our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself. This is a story with some happy parts in it, and, in fact, governments in Canada did learn, haltingly and grudgingly, that there are limits on the amounts that governments could safely extract from the industry, and that some assurances of long term fiscal stability were necessary if investors were to be induced to make massive commitments which could only be recovered over very lengthy periods.

Jan 1, 1982

By A. J. S. Spearing, A. Mueller

The support of intersections in coal mines remains an important safety issue, mainly because the large diagonal span compromises the stability of the roof. This structural weakness is further exacerbated if the intersection is developed incorrectly, the pillar corners fail or the crosscuts are angled (not perpendicular). This report details the current support systems used and investigates unplanned falls of ground in intersections in coal mines throughout the United States. A possible failure mechanism is proposed and some suggestions are made to improve the effectiveness of the support in these vital areas.

Jan 1, 2009

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

"To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.INTRODUCTIONCopper is one of the first metals extracted and the main material of choice for different high-technology applications today. Currently 80% of the world's copper comes from copper sulfide ores. However, due to the depletion of high-grade copper ores in the world and constantly growing demand for copper, the need to develop processes and technologies to treat copper resources from additional sources such as mine tailings, low grade deposits, industrial wastes and deposits with high impurity levels such as As and Sb will continue to increase (Miller and Craig, 1983). The beneficiation processes of copper-pyrite ores consisting of tennantite-tetrahedrite series minerals are generally complex. Tetrahedrite-tennantite minerals occur as fine anhedral grains intermixed with grains of galena, sphalerite, chalcopyrite, pyrite and other sulfides (Saharova, 1966). The mineralized zones of Southern Urals, Russia deposits correspond with these ore types but tennantite-tetrahedrite series are more abundant in ores at the Uzelginskoye deposit, some samples of which contain 70% of copper in tennantite form (Seravkin et al., 1994). This deposit differs from other similar copper-pyrite ores by thin mutual ""germinating"" minerals and higher content of arsenic (up to 0.8-1 %) which create additional considerable problems in enrichment (Solozhenkin et al., 2016)."

Jan 1, 2018

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By Kevin G. Stricklin

Introduction Continuous monitoring techniques have been used in the US and abroad for many years. A continuous miner has a monitor that measures methane and automatically gives a warning if the methane exceeds 1%. It deenergizes the continuous mining machine automatically at a maximum concentration of 2%. Main fans are also continually monitored to ensure operation. Alarms may also be given at a remote location should a fan slow or stop. The systems being developed can continuously monitor various gases and equipment throughout the mine and transmit pertinent data to a surface monitoring station. At this station, conditions throughout the mine can be monitored and, in some instances, controlled. These are known as Mine Wide Monitoring Systems (MWMS). History The use of environmental monitoring systems began in 1976 when a federal court approved the petition of modification to use belt air at the face. The first mine to receive a modification did install a system to supplement existing safeguards. Later, the Mine Safety and Health Administration (MSHA) and the US Bureau of Mines (USBM) conducted tests dealing with the use of belt air. Findings from these tests are being used to set guidelines as requirements of a petition. These requirements include: • Velocity of air has to be 0.25 to 1.5 m/sec (50 to 300 fpm); • Monitors will be installed at each belt drive and tailpiece and at intervals not to exceed 610 m (2000 ft); and • An alarm level of 10 ppm, above the ambient level is appropriate. The early uses of environmental monitoring could only be used outby the last open crosscut. That may be a reason for an initial slow growth of these systems. In June 1982, MSHA began evaluating systems that could be used in returns to ensure that monitoring systems being used in areas where permissible equipment is required does not of itself pose an explosion hazard. This is known as the Mine Wide Monitoring Systems Evaluations and Sensor Classification program. The evaluations and classifications granted are based on electric currents and voltages. Use of mine wide monitoring systems The environmental aspect of MWMS in today's coal industry deals with carbon monoxide (CO), methane (CH4), and air velocity. Just as all mines are different and encounter different problems, the MWMS are diverse and can be used to provide necessary data in all areas of coal mines. Mine operators in an ultragassy seam, for example, may be concerned with monitoring methane, while a mine that used diesel equipment may want to continuously monitor for diesel contaminants. In a mine with roof fall problems, airflow monitors may be helpful as an indication of whether the air is flowing in its normal course and at its normal volume. Today's MWMS can monitor any or all of these parameters. Most systems can be expanded as mining needs require. For example, a mine is now being monitored for methane and five years from now CO monitoring would help increase safety. It may be possible to use the same system by adding additional equipment. In the US, 30 environmental monitoring systems were installed from May 1985 through May 1986. In 1984 and 1985, there were 38 and 44 environmental monitoring systems in operation, respectively. Due to mine closings, 11 of these are no longer in use. However, the number of mines using environmental monitoring systems increased to 63. Use of these systems are not limited to any geographic area or

Jan 9, 1987

By AIME

To be born in the East, reared and educated in the West, to do graduate work in Germany, leading to the doctorate in metallurgy, and to wind up-for the time being at least-in the Middle West as head of one of the outstanding mining and engineering schools of the country, is a unique career. Curtis Laws Wilson, dean (and in most respects, president) of Missouri School of Mines and Metallurgy at Rolla, is a native of Baltimore. He came to Anaconda in 1918 and in due course was graduated from Montana School of Mines, with an exceptional record. In 1921, after experience in metallurgical research at Anaconda, he became instructor in metallurgy at his alma mater. Because of his ability as a teacher, he rose rapidly to head of the department after special work at Columbia in 1923-24. In 1927, Wilson was granted leave of absence to study physical metallurgy under the great Tammen at Goettingen, and returned with his doctorate to his work at Montana School of Mines. His major metallurgical interest was then in age-hardening of copper alloys. Also after his return to Montana Mines, Wilson started

Jan 1, 1948

By Jetson Lemos Ferreira

O presente estudo teve por objetivo verificar a independência tanto da Curva Limite de Tensão (CLT), quanto da Curva Limite de Deformação Plástica Efetiva (CLDPE) em relação à trajetória de deformação. Para tal, foram utilizadas Curvas Limite de Conformação (CLC) de aço livre de intersticiais (Interstitial Free - IF), determinadas, primeiramente, por meio de trajetórias lineares e, posteriormente, por trajetórias bi-lineares estabelecidas por níveis de pré-deformação nos modos de tração uniaxial e estiramento biaxial simétrico. As previsões da CLT e da CLDPE, calculadas a partir das deformações limites da CLC convencional em trajetórias lineares e bi-lineares, mostraram-se independentes em relação à trajetória de deformação. Entretanto, verificou-se que o critério de escoamento adotado tem grande influência na forma e posição destas curvas limites.

Aug 17, 2017

By T. T. Wang, T. H. Huang, S. S. Zhan

"Fractures with diverse features dominate the hydraulic behavior of fractured rocks and are one of the major subjects for hydrogeological characterization of a site. This study investigates curve patterns obtained by packed tests, and as well the influence of fracture features based on 59 sets of in situ packer tests with different fracture combinations and fracture features. The result shows that, in the example of Heshe site, neat and tidy fractures usually provide stable channel for water flow during testing, and the hydraulic properties of fractures infilled with breccia and mud may change during testing because of leaching and/or washed out of infilling breccia and mud. Different combinations of fractures with diverse features in packed test sections lead to different curve patterns for in situ hydrogeological tests. For groundwater flowing predominately through neat and tidy fractures, the pressure-discharge curve of modified Lugeon tests are usually linear curve pattern, and the pressure decrease while the discharge increase in pressure-discharge-time curves of single-hole double packer tests, which benefit statistically determining the transmissivity of dominant fracture sets. INTRODUCTIONFractures interlaced in rock masses are major channels for groundwater flow and generally account for the anisotropic and heterogeneous characteristics of permeability for fracture rocks. To describe reasonably the permeability of a fracture rock, the Discrete Fracture Network (DFN) approach and others with similar ideals have been developed. Many methodologies and associate equipment, for instance, the televiewer and the in situ hydrogeological test, have been proposed to investigate the spatial distribution and the transmissivity for different fracture sets, which are two main parameters necessary for the DFN or similar model simulation (Pearson & Money, 1977; Barker & Black, 1983; Hsieh et al., 1985; Bernard et al., 2006; Quinn et al., 2012). However, diverse outlooks for the pressure-discharge curves and the temporal pressure and associate temporal discharge curves often confuse the investigation results by significant deviations on derived permeability (Houlsby, 1976; Zlotnik, 1994; Royle, 2009; Camilo, 2010).Aiming on technical development for in situ hydrogeological tests and fracture investigation, an experimental well site with 10 wells has been established in Heshe in central Taiwan since 2011 (Wang et al., 2011; Song, 2012; Zhan et al., 2013). Extensive geological survey and well-hole scanning by a televiewer provide spatial distributions and outlooks of fractures in detail. Additionally, a series of Lugeon tests, double packer injection tests and pumping tests have been performed to investigate the permeability of fracture rocks, and dominate fracture sets as well. Based on the results obtained from the Heshe site, this study classifies the curve patterns of hydraulic packer tests. The features of fractures involved in packed sections for packer tests are then inspected in detail. Relationship between the curve patterns of hydraulic packer tests and associated features of corresponding fractures in rock are discussed and addressed accordingly."

Jan 1, 2015

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014