Search Documents

By Paul Kunze

When a new bridge was needed across the upper reaches of the Yellowstone River in Montana, removing the old concrete bridge piers became an environmental concern for the highway department engineers. The location is about fifty miles downstream from the north edge of Yellowstone Park. The determination was made by the federal and state agencies charged with protecting the resource, that the old piers had to go but the river bed had to remain unchanged. Concerns were expressed that removing the concrete presented the potential for environmental damage to this protected portion of the river. These concerns prompted the state to place stringent restrictions on the contractor in the way they carried out the demolition and disposal of the piers. The reinforced concrete masses had to be removed to an elevation at least fifteen feet below the river bed and every bit of concrete debris had to be removed from the river channel. Explosive removal was discouraged, but the only other options: saw cutting, mechanical or chemical breaking, were not viable.

Jan 1, 2014

By D. Wenstrup, K. Perry, J. Hatfield, P. Sainato, B. Lusk

Concrete-infused cloth is used in several civil and mining surface applications whose circumstances are similar to some of those in underground mining. A feature of this material is that it cannot be overhydrated. In underground conditions, however, the excess supply of water to the cloth for hydration could lead to muddy and potentially unsafe working conditions, as well as resource wastage by supplying more water to the construction site than is needed. The objective of this study is to verify the water-to-cloth ratio and study the effect of hydration level on the strength of the Concrete Cloth product. We found that the strength increases with increased hydration up to a 1:2 water-to-cloth ratio by weight, after which the strength holds steady regardless of additional hydration. This confirms the 1:2 water-tocloth ratio by weight for hydration and confirms that strength is retained even if the cloth is excessively hydrated.

Jan 1, 2014

By L. C. DeCory

"Concrete is a common denominator to the building process and portland cement is an integral and necessary component of concrete. The cost of portland cement is nominal and its cost comprises, in most instances, a small portion of the total cost of ""put-in-place"" concrete.The domestic demand for portland cement in Canada is projected to be slightly less than 11 million short tons in 1980. In order to achieve this projected goal, stabilization or lowering of the cost of put-in-place construction is necessary. This enhancement of the cost of building can be achieved by:(1) improving the building process;(2) refining and improving design techniques; and(3) developing improved and economical concrete products.Some of the techniques and materials that will lead to building cost stabilization include systems building in its broadest sense, slipforming, precasting, prestressing, computer design, lightweight aggregates, fibrous concrete and integration of building components."

Jan 1, 1973

By Charles Roeder, Amy Leland, Dawn E. Lehman

Concrete filled steel tubes (CFSTs) are composite members that are commonly used in many countries today. CFST components are used in the United States, but they are more common in Asia, in part because the connections used in Asia are quite labor intensive and there are not standard connections in the U.S. In addition, US design specifications are prepared by separate groups for structural steel and reinforced concrete structures and so composite systems that use CFST components are not overseen by a single group and as such there are several, conflicting design standards. In the US, steel tubes used for CFST are more slender (i.e., the diameter-to-thickness, D/t, ratio is larger) than some other countries, and labor practices (structural steel labor is different than reinforcing steel labor) also cause potential conflicts in construction. As a result, CFST has had some use in tall building construction in the US, but very limited use in bridge construction. A research program at the University of Washington has been in progress to address many of these issues with an eye towards universal design expressions, simpler, standardized connections and promotion of accelerated bridge construction (ABC). The research has resulted in recent changes to the American Association of State Highway Officials (AASHTO) bridge design specification as well as state departments of transportation (DOTs), which supports the increased use of CFST in bridge pile and drilled-shaft foundations. An experimental research study which investigate the flexural strength, shear strength and connections was conducted. These connections provide good performance under both seismic and gravity loads and address the concerns of US construction. These connections, their design rules and requirements, and their impact on composite behavior and system performance are discussed. These results permit rapid and economical construction of CFST bridge piers, piles and drilled shaft foundations. They encourage the use of more slender and economical tubes, while achieving the benefits of composite construction. INTRODUCTION Concrete filled steel tubes (CFSTs) are widely used for bridge and building construction in Asia, but the use of CFST in bridge construction is limited in the US. The historical use of structural steel and reinforced concrete in US bridge construction have resulted in more developed design expression for those construction methods, which has limited the use of CFST. Bridge construction in the US is inherently different than in Asia because of differences in codes, labor costs and construction practices. As a consequence, design and construction practices that are economical and practical in other countries may not be practical for US bridge construction.

Jan 1, 2019

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By Nuno Cruz

"The concrete overbreak estimation for bored piles provides the quantification of the shaft’s expansion beyond its theoretical volume. There are stability analysis methods that can be employed before and after concrete pour but as for the moment of decision, during pile cast, the most common method still consists in measuring the rising of the concrete level in order to compare its poured volume with the theoretical pile section volume. This is a determinant parameter to monitor, not only because it assesses the bored shaft stability but also because it represents a direct cost. When analyzing the estimation methods commonly applied on-site it becomes evident that these are often affected by human errors that lead to misleading results. The objective of this paper is to identify those errors and discuss a subject which is usually overlooked. As a general conclusion, it was ascertained that most errors derive from inaccurate volumetric data, working procedures and gauging equipment. By acknowledging these widespread practices deep foundations contractors will be in a better position to make informed decisions on how to correct and improve bored pile stability.GENERALBackgroundWhen executing bored piles, the estimation of its concrete overbreak allows a swift appraisal of the excavation stability during the drilling process. This is simply obtained from the proportion of the poured volume of concrete over the drilled shaft theoretical volume, as shown in equation [1].Where CO = concrete overbreak percentage, Vc = volume of poured concrete, Vr = pile’s theoretical volume. This calculation not only provides a general idea of the shaft’s expansion from its theoretical volume, but also the outline of the excavated column’s geometry. For the latter, the outline will be as accurate as the number of measurements taken for each partial known volume of poured concrete. This means that for each load placed inside the excavation there is a corresponding rising of the concrete level. The profile of the definite pile is then plotted (see Fig. 1) and allows inferring about how stable remained the shaft walls up to the moment of casting.The technological developments in this area have provided other methods for determining pile stability before and after pile cast, such as ultrasonic echo sensing, cross-hole sonic logging or thermal integrity profiling systems. Notwithstanding, concrete overbreak assessment remains as common practice and confers the advantage of providing stability information during the process of pile casting."

Jan 1, 2017

By L. D. Johnson

12 groups of 12 precast prestressed (PCPS) piles were driven in the lagoon of Kwajalein Island to support a dry dock. Pre-construction investigation of the calcareous coral sands and static pile loeid tests were performed to determine if the 7.9 by 7.9 cm (20 by 20 inches) by 26 m (85 ft) long PCPS piles embedded to a depth of 16 m (53 ft) would adequately support the dry dock. Driving records for production piles indicated that the blowcounts of the piles at the fincil embedment depth became substantially less than expected as piles wssre driven further toward the lagoon end of the dry dock and decreased to as low as 2 blows/ft. A supplemental investigation that included a static load test on a production pile, the driving of an indicator pile, and restrikes indicated that the pile foundation has adequate bearing capacity. The observed bearing capacity appears to be effected by several mechanisms including breakdown of cementation between sand particles, densification of the sands during driving, and dissipation of excess pore pressures and recementation after driving.

Jan 1, 1993

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

By Oscar Cabello, Luis Mendieta, Maribel Guzman

Mineral flotation processes generate large volumes of tailings, which must be disposed of efficiently and safely. In addition to dry stack disposal, the possibility of reusing these tailings as aggregates in shotcrete is an interesting alternative. Tailings samples from a mining operation in southern Peru were characterized by granulometric analysis, X-ray diffraction and Scanning Electron Microscopy. Concrete samples were obtained with different tailings formulations. The samples were subsequently subjected to geomechanical testing. The results showed that replacing 20% to 30% of the tailings with aggregates in shotcrete production achieved compressive strengths exceeding 30 MPa after 28 days of curing, with an energy absorption capacity of 500 joules. Results show that this shotcrete can be used in the support stage of the mining cycle in underground mining.

Feb 22, 2026

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

By James D. Piper

In the summer of 1957,9 the University of California sponsored a World Conference on Prestressed Concrete in San Francisco to which were invited a number of Soviet engineers. While attending the conference, these engineers in turn asked the University to form a delegation of American engineers to visit the Soviet Union the following year for the purpose of studying Soviet advances in concrete technology. A six man delegation was formed, and the dates of the Russian tour fixed for May 10th through May 21st, 1958. Before arriving in the Soviet Union, the American Delegation attended the Third International Congress on Prestressed Concrete in Berlin. While there, we noticed that the delegation from the U. S. S. R. used displays and showed motion pictures of many construction projects which we later were shown in Moscow. Our delegation left East Berlin by Russian aircraft on May 11th, and arrived in Moscow that afternoon. We were met by our Russian engineer hosts from The Academy of Construction' and Architecture who made all subsequent arrangements for our itinerary. This Academy has no counterpart in the United States. It. does 40 per cent of all engineering-and scientific work in the building construction field and coordinates 60 per cent of that done by other Soviet agencies. Due to the prestige of the Academy in Russian affairs, our delegation was able to obtain a surprisingly broad picture of construction activities in Moscow and Leningrad in just ten days time

Jan 1, 1960

By Gaifeng Xue, Lijun Lu, Honghui Fang, Jiannyang Hwang

"Steel slag has been stockpiled in many steel mills due to its poor performance in various construction related applications. Free lime in steel slag has been considered as a major barrier for its utilizations. Composite of steel slag and powders of granulated blast furnace slag have been found an excellent cementitious material for concrete. Portland cement is not required in this kind of concrete. Concretes with various amounts of steel slag and powders of granulated blast furnace slag additions have been investigated. Physical and chemical properties of the products were examined. High performance concrete can be obtained. Field testing of the concrete products was conducted for various applications, including buildings and pavements, and the results demonstrated the soundness of the concrete. Drill cores of field tested concrete, with ages up to 26 years, were examined for the microstructures under SEM.IntroductionIn the steel industry, a major source of the solid waste is steel slag. Steel slag has poor stability in construction applications. This is a major reason that only a small amount of steel slag has been utilized. Some of the reported applications include the land filling/creation in the sea, road base materials, soil treatment for acid neutralization and micronutrients supply, and sintering aid in the sintering plant of the steel industry [1].To solve the stability problem for using steel slag as construction materials, the common approach is to find a method capable of depressing or eliminating the expansion of steel slag. Free lime in steel slag is the major component that causes the expansion. Aging and hydration pretreatment of free lime in steel slag are the well known methods for increasing the steel slag stability. However, there has been limited success on these approaches due to that a large portion of free lime is locked in the grains during the pretreatment process."

Jan 1, 2012

By Robert Thomas

DURING the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of inter-ruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publi-cations a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, there-fore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.

Jan 1, 1936

By Edward M. Dowey

The concrete lining for a long 8.05 km (5 mi) section of New York City Water Tunnel No. 3 was cast in place. The contractor, Grow-Perini-Skanska, placed over76,841 m3 (100,505 cy) of concrete, pouring 24 hours per day, 5 days per week. The concrete was dropped 204 m (670 ft) to the tunnel level, transported by rail to a concrete remixer and pump, and placed in 146.3m (480 ft) of full circle forms. Some of the many challenges include the sheer magnitude of the job, navigating through drifts, a raise and curves, dealing with ground water inflows, and placing the concrete within time limits.

Jan 1, 2001

By Vitor Guarnier Domiciano

A necessidade de melhorar as propriedades dos refratários monolíticos para resistir às condições operacionais cada vez mais severas e instáveis das casas de corrida de Alto-Forno tem sido um grande desafio para os fornecedores de refratários de maneira a garantir a segurança dos canais de corrida e sua disponibilidade para operação. Este trabalho apresenta as propriedades de novos concretos refratários Al2O3-SiC-C (aplicados por vibração ou bombeamento/projeção a úmido) desenvolvidos para resistir ao severo mecanismo de corrosão que ocorre na linha de gusa de canais principais e que exige constante atenção dos operadores das casas de corrida. Testes realizados com os novos concretos refratários em canais de corrida principais de diferentes Altos-Fornos de grande produtividade revelaram uma significativa diminuição da velocidade de desgaste do revestimento refratário na linha de gusa oferecendo uma condição operacional segura e confiável às casas de corrida.

Aug 16, 2017

By Vitor Guarnier Domiciano

Pre-shaped refractory burner blocks play an important role in reheating furnaces operation and melt shops production since they are responsible for heating the billets/plates so that they reach the temperature required for lamination. This paper presents the main characteristics and properties of a new refractory castable developed for pre-shaped burner blocks, which significantly improved the performance of reheating furnaces burner blocks. Tests carried out in 3 different melt shops have shown that the new refractory castable was able to extend the service life of the refractory burner blocks from 1 year (standard product) to more than 3 years (new castable), showing perfect conditions to continue operating for a longer period.

Oct 30, 2017

By Yong Kuk Park

The horizontal cold chamber die casting process can produce a wide range of near-net shape, non-ferrous castings with small dimensional variation, excellent surface finish and very complex geometries. However, top quality die castings can be achieved only when optimal performance of the cold chamber and plunger is maintained during the molten metal injection phase of the process. Cold chambers (shot sleeves) are known to deteriorate fast and sometimes fail catastrophically because of poor design. Catastrophic fracture and wear due to deformation are leading causes to degrade quality, increase downtime and thereby decrease productivity and profitability. Therefore, a systematic approach to minimize irregular and adverse conditions which prevent an intended injection profile, is highly desirable. To eliminate them, design criteria for shot sleeves were developed using analytical tools and available experimental data. The correlation between design and mechanical failures of shot sleeves was shown by the data obtained from the die casting industry. Also, the relationship between die casting process parameters and deterioration/ failure mechanisms were carefully evaluated.

Jan 1, 1996

By Worthen Bradley, R. G. Hall

THIS paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer to the Bradley Mining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a rotary kiln at the same end-that is, of course, the upper end. This is as opposed to "counter-current firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. EARLY REFERENCES The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,1 its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver . . . is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and flies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake County, California. The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank. Reed and Sulphur Bank ranked respectively fifth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: Sometimes there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of . . . the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away. as its richness and value were not

Jan 1, 1945

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016