Search Documents

By E. E. White

In August, 1911, I read a paper before the Lake Superior Mining Institute1 on surveying and sampling diamond-drill holes. The present paper gives a more thorough descriptiou of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling' and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drillholes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-hole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a

Jan 1, 1913

By Robert R. Abbott

The practice of carbonizing steel for the purpose of case-hardening has assumed great commercial importance within the past 10 years. Formerly, case-hardened steel was held in more or less contempt, since it was considered a cheap substitute for tool-steel. This is no longer the case. The development of the motor-car industry, and coincidentally that of modern alloy-steels, has resulted in overcoming many difficulties formerly experienced in case-hardening. This result has been accomplished by increased knowledge regarding the analysis of the steel which would respond most readily to case-hardening, and by more careful methods of treatment of the carbonized steel. The ordinary method of carbonizing consists in packing the steel with the carbonizing-material in cast-iron boxes and placing them in a furnace at a temperature of from 1,500° to 1,900° F. for a time sufficient to give the required depth of " case." The steel is then either quenched directly from the box, or is allowed to cool without unpacking, and finally given a single hardening-heat, or, for special work, two or three heats. During the year 1911, more than 100,000 tons of carbonizing-material was sold in the United States, at an average price of probably $55 per ton. More than 85 per cent. of this material consisted of granulated bone. Within the past four years, many manufactured compounds have been placed on the market, consisting largely of some form of carbon or carbonaceous material, with or without the addition of chemicals. Steel will absorb carbon placed in contact with it at the temperature of the atmosphere. The reaction is exceedingly slow, but increases rapidly with increasing temperature. Below

Jan 1, 1913

By N. V. Hansell

The preparation of low-grade iron-ores by concentration, whether or not followed by an agglomeration of the concentrate, has in the United States only recently been recognized as a metallurgical process of vast economical importance for its iron indust.ry. This importance of the process lies not only in the fact that it makes possible the use of ores heretofore discarded on account of their low iron-content or their too high percentage of elements deleterious in the iron industry, but also in its produetion of a raw material for the blast-furnace that is more uniform in its physical character and chemically purer, with a higher iron-content, than the general run of natural ores. When mixed in the burden of the furnace, it lowers the amount of coke and fluxing-stone required per ton of pig-iron produced. The furnace-operations become more regular and more easily controlled. The pig-iron is of higher quality and more uniform in character. In brief, it is becoming recognized that the beneficiating of the natural iron-ore, even if it makes the furnace-ore higher in cost per unit of iron entering into the burden, may mean a lowering of the production-cost of the pig-iron and an improved product. At the present time, the Lake Superior district furnishes about 80 per cent. of all the iron-ore yearly produced in the United States. If the Southern States arc exempted the percentage runs as high as 93 per cent. These ores are showing a steady decrease in grade from year to year. For the past 10 or 15 years this falling off in the average grade has been about 0.5 per cent. a year. The lowered grade of ore means an in-

Jan 1, 1913

By C. A. Stetefeldt

Jan 1, 1892

By W. H. Adams

Shortly after becoming one of the van-guard of mine-developers in the State of Virginia, during the year 1883, I called the attention of the Institute to certain deposits of pyrites, which have been largely worked since. In all cases these deposits are covered with iron-ore (limonite), extending 40, 50 or 60 feet from surface to water-level. The several classes of brown iron-ores are found almost continuously along a prominent ridge of mineral-bearing slates, which can be traced from the James river northeasterly to the North Anna, the Rappahannock and the Potomac rivers, crossing the counties of Louisa, Spottsylvania and Stafford. Outcrops are plainly discoverable from end to end of this belt, also, in places, to the right and left of it, and at intervals there are evidences of workings, some of them for known purposes and others of unknown age and meaning. These old workings have an interest aside from the minerals they may contain or may have yielded. I have been engaged during the past five years in the collection of facts concerning them, which might determine definitely the site of those iron-furnaces, placed by tradition within reach of " the towne called Germanna," which were the first ever built in this State or on this continent. The events which led to the establishment of this important industry are sufficiently narrated in a paper written by Mr. R. A. Brock, Secretary of the Virginia Historical Society, and printed in the Proceedings of the National Museum, 1885, page 77, from which I quote the following : " To Virginia, the first of the English settlements in America, belongs the honor of inaugurating within her limits, as a colony, that most important industry, iron manufacture. "The London Company contemplated a variety of manufacturing enterprises from the very beginning of its authority; prominent among them was that of iron. In 1610 Sir Thomas Gates testified before the council of the Company at London, that in Virginia ' there were divers minerals, especially iron-oare,' lying upon the

Jan 1, 1892

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913

By W. A. Barrows, Carl Zapffe

Jan 1, 1913

Joseph E. Thropp, Jr., Indiana Harbor, Ind.:—To what do you attribute the fact that in some localities the by-product coke sells at a premium over the ordinary bee-hive coke for foundry use ? If the cell-structure is preferably soft and rather thick in coke for foundry use, as I understand it, do you mean that by-product coke has soft and thick cell-walls ? William H. Blauvelt, Syracuse, N. Y.:—As I say in one of the paragraphs of my paper, the tendency seems to be towards the manufacture of foundry- and furnace-coke under somewhat different conditions. The development of the best cell-structure in coke, of course, has not reached perfection, but we are making progress, and we are inclined to believe that under ordinary conditions the best furnace-coke, that is, coke with the hard cell-wall and the well-developed cell, is produced at fast coking-time and high heats, whereas the best foundry-coke seems to be produced at somewhat lower heats. In one of our plants we are making furnace-coke in 16-hr. coking-time, and foundry-coke in 20-hr. time. Foundry-men want the strong, tough coke. I think the furnace-men present will agree that the best furnace-practice requires a hard coke, with a well-developed cell-structure. Replying to the question as to the reason for higher prices being realized for by-product foundry-coke than for bee-hive coke, of course, the immediate reason is that it suits the foundry-men better. Perhaps one cause may be that we are able, by the selection of coals, which is not usually practicable at bee-hive plants, to get a quality and analysis best suited to foundry-work, with high carbon-content, and with cell-structure and physical strength especially suited to the foundry-men's ideas.

Jan 1, 1913

By F. E. Lucas

This paper is offered with considerable diflidence, since some of the statements made may not agree with the opinions of other members of the Institute. What I give is the result of some years of experience in the operation and construction of coke-ovens, and observation of plants in America and Europe. Although my title is " The Manufacture of Coke," I have found it impossible to do justice to the subject without touching on a number of points which, while not strictly involved in the making of coke, yet are of paramount importance from an economic standpoint. There are, indeed, many points of interest, on each of which a separate paper of considerable length might be written, but the scope of my paper will permit me only to touch lightly some of them, in the hope that what I say will promote a full discussion on the whole question. Those of us who are interested in the manufacture of coke are under an obligation to the American Institute of Mining Engineers, which has opened its meetings to the discussion of this subject. I do not believe that there is any question to-day more worthy or more in need of discussion. When geologists and mining-men tell us that, at the present rate of consumption, our coal-fields will be exhausted in a few generations, me should welcome any means that will conserve these deposits as far as possible, and give us the greatest amount of heat or power from every ton mined. I shall try to show that much can be done in this direction through the by-product coke-oven, and that it should stand second to none as an economic factor in the industrial world. I shall here deal exclusively with the by-product oven, except for the comparative statement I hare prepared, showing the saving to be effected by coking in by-product instead of beehive orens. It should be borne in mind that this comparison

Jan 1, 1913

By William Campbell

The structure of iron and steel, though the object of so much study and research for the past 25 years, is by no means thoroughly understood. In the first place, we have three or more distinct iron-carbon thermal diagrams, each with its own supporters, and each representing a theory of the structure and constitution of cast-iron. In the second place, by reason of the fact that austenite, the solid solution of carbon in iron, decomposes in the solid state into ferrite, or pure iron, and cementite (Fe3C), and that quenching from above this transition-range, no matter how rapid, cannot entirely prevent the change and thus preserve the austenite by itself at ordinary temperatures, it happens that under the microscope we find, in addition to the ferrite, Fe3C, and austenite, which the thermal diagram of steel requires, a series of transition-products with distinctive structures, to which have been given the names martensite, troostite, sorbite, etc. Now these transition-products, in addition to the solid solution, austenite, have been the source of much controversy, at times very bitter. One side would insist that, say, troostite was an entity, which the other side would deny, pointing out that it must be a transition-mixture, with a particular structure. That austenite was a solid solution of carbon in iron has been denied by one school; we have been told that Fe24C dissolved both Fe3C and Fe, and thus gave rise to a whole series of quenching-pro-ducts—all this in spite of the fact that no matter how the thermal diagrams differ in regard to cast-iron, they all agree in regard to the solid solution, austenite, for Fe24C finds no place on the diagram. Thus it happens that while the authorities fight both in regard to the iron carbon diagram and the structures met with in hard-

Jan 1, 1913

By C. A. Stetefeldt

Metallurgical processes cannot be conducted successfully With out the aid of analytical chemistry. The great perfection of Iead smelting in the West, for instance, has only been accomplished by the analysis of ores, fluxes, slags and all products of the furnace. Ores are mixed and fluxed to obtain a slag of desired composition. Account is even taken of the composition of the ashes obtained from the coke. The " muscular " smelter has left the field forever! This state of affairs has been induced by sharp competition, i.e., by a com plete separation of the industries of mining and reducing ores, not by the liberality and wisdom of directors and stockholders to pro vide laboratories and engage chemists, or by their love for scientific investigation. It would be considered absurd, at present, to run a lead-smelter, a blast-furnace for pig-iron, or a Bessemer plant without the assist ance of a well-equipped laboratory and a chemist; but it is con sidered quite sufficient to provide amalgamation- or lixiviation works merely with a crude assay-office, and an assayer who is paid less than a laborer in the mill. In my opinion, this will change in the near future. By the ex clusion of Mexican lead-ores, and their growiring scarcity in the West, smelters have been forced to raise their charges on so-called dry silver-ores, and cannot handle the latter now in such unlimited quantities as formerly. The inevitable result must be that the sur plus of these dry silver-ores, especially those of low grade, will be reduced by processes cheaper than smelbing; and here the introduc tion of lixiviation has an excellent field, provided the muscular lixiviator has an able chemist for an assistant. It is to be regretted that so little analytical work has been done in lixiviation. We know almost nothing of the composition of roasted ores before and after lixiviation; of the constitution of the first wash water and of lixiviation-solutions after prolonged use; of the chemistry of sodium and calcium sulphides; of the col-hposition

Jan 1, 1892

By John Jermain Porter

In taking up this subject it is first necessary to define our terms. Efficiency, in its engineering usage, means the ratio between actual and theoretical results, and efficiency-records thus involve the use of scientifically determined standards with which all results are compared. Scientific management is the methods used in increasing efficiency, and includes the use of efficiency-records. Efficiencj-records do not alone constitute scientific management, but they are necessary to it, and any so-called system of management which is not based upon standards and standardization is fundamentally wrong. An efficient management and efficiency-methods in management are not the same thing. There are some people who have an instinctive genius for management and accomplish results without exactly knowing how they do it. Such a manager may obtain a very high efficiency without the aid of scientifically determined standards. On the other hand, it sometimes happens that poor results will accompany the use of efficiency-recorcis, due to a weak or indifferent management, which fails to make use of the information acquired. Efficiency-records are only a tool, and like other tools are worthless unless used. The ordinary cost-sheet and production-statement do not go far enough. They tell what has been done, but give no information as to how well it has been done. It is true that the man who is familiar with the industry and the plant in question may draw inferences and form a general idea of good work or bad work, but it can only be a very general and hazy idea. Comparisons with previous records or records of other plants are unsatisfactory, since there is nothing to show the cause of the differences. Efficiency-records supply this need. They compare actual

Jan 1, 1913

By Henry E. Wood

In my opinion, the concentration of minerals by flotation is the most interesting problem in ore-dressing, and will command eventually far more consideration than it has at present. For many ores it furnishes a complete method of concentration absolutely independent of specific gravity, and thus simplifies the milling of many difficult combinations. Not having to recognize the influence of specific gravity, we are also able to dispense with some of the complications resulting from classifying-conditions. Where flotation cannot be used for a complete separation of the minerals from the gangue, it will be found, in nearly all cases, to save those portions which are generally lost by reason of their fine state of division. For this reason, it should be looked upon mainly as an aid to general concentration, although there are many ores so well adapted to flotation that more than 90 per cent. of the valuable metals can be recovered from them in one operation by this process. In presenting the results of my investigations in flotation, I have endeavored to theorize as little as possible. That side of the subject has been extensively discussed by others. My earliest work with flotation was done in 1895, when I used various oils, grease, soap, etc., with results that were remarkable. I did not realize then that with water alone equally good separations could be made. Up to 1906, my endeavors were confined to attempts to keep the concentrates on the tables well wetted and away from exposure to the air. In common with others, I observed that when there mas any obstruction in the wash-water on the table of sufficient size to divert the water to either side, the concentrates collected, and, on exposure to the air, would promptly float away. This convinced me that the sulphides were all good "swimmers," and that if,

Jan 1, 1913

By A. L. Holley

The general usage of engineers, manufacturers, and merchants, is gradually, bat surely, fixing the answer to this question. In every country rails, boiler-plates, and machinery bars, whether hard or soft, are almost universally called steel, when they are made from cast ingots. Other names for the softer steels, such as " homogeneous metal,'' "Bessemer iron," " Martin iron," and the like, have failed to obtain general recognition. The meaning of the term steel, before it was enlarged to cover newly developing varieties, has been traced, by a recent writer, down through Percy, Shakspeare, and the Bible, in a most interesting manner, from an archœological point of view. Undoubtedly, it did characterize hardness arid other qualities imparted by carbon. It is within the memory of most of us, that all steels were tool steels, and that the soft, structural varieties were introduced—varieties which harden but little, which bend cold, and which, in many physical properties, are akin rather to wrought-iron than to tool-steel. But, since both the hard and the soft steels are made by the same processes, and have their great, distinguishing structural feature in common, viz., homogeneity resulting from fluidity, it has come to pass, despite every other proposed nomenclature, that all the compounds of iron which have been cast in malleable masses, are called steel, the term wrought-iron being still confined to malleable iron made from pasty masses, and hence laminated in structure. No inconvenience has been found, so far, in distinguishing between the more or less carburized products, in general, by the terms " highsteel," "low-steel," "tool-steel," etc., and, in particular, by prefixing the percentage of carbon and other ingredients, to the terra steel. Steels which contain distinguishing ingredients other than carbon, are called "chrome-steel," "titanium-steel," and the like, just as variously compounded bronzes are called " phosphor bronze," " aluminium bronze," etc. Thus the combination of several words or symbols, and figures, may completely disclose the characters of the metal, in terms that are subject to no misunderstanding. But inasmuch as several high metallurgical authorities and clever writers have of late proposed to disturb this natural and somewhat settled nomenclature, it seems important to consider the claims of the various classifications. I shall attempt, in this paper, to show

By N Elith

Coal is a valuable energy source in New Zealand and has been mined from the West Coast for over 100 years. Stockton Mine is New Zealand's largest opencast coal producer supplying around 1.5 Mt of hard coking and thermal coal to international markets annually. The Stockton Plateau forms an extensive, gently inclined dip slope on erosion resistant Lower Eocene Brunner Coal Measures unconformably overlying basement rocks. The dip slope rises 600 - 1000 masl, locally dissected by fault scarps and present-day fluvial systems, some of which are deeply incised. Within the Mt Augustus Mining Block overburden comprises of a 30 - 40 m thick sequence of fluviatile, coarse to granular coal measure sandstones. High quality coking coal is preserved as a gently dipping, 10 - 12 m thick seam. High and sometimes very steep cliffs of jointed overburden shape the skyline escarpment, above steep forested slopes and gullies. As mining has progressed at Mt Augustus individual coal blocks are progressively becoming more technically challenging. This paper outlines the scientific approach taken by Solid Energy International and mining contractors to carefully unlock many thousands of tons of coal whilst protecting nearby flora and fauna from the impacts of dislodged rock and other blasting side-effects. The strategy involved: an expert-driven onsite risk assessment,formulation of a management plan to manage impacts,conducting an in situ vibration research program, andanalysis of results and operational designs to eliminate potential environmental problems.

Jan 1, 2003

By E. C. Dowling, S. A. Elmquist, L. A. Kipfstuhl

The Cliffs and Associates Limited (CAL) 500,000 tpy HBI plant located in Trinidad was commissioned after modifications in early 2001. This plant employs the novel Lurgi Circored® process to reduce iron ore fines using a combination of circulating fluidized bed and conventional fluidized bed reactors in a hydrogen based. This paper will review the advantages offered by working in the Caribbean nation of Trinidad and Tobago, the Circored® processes, and plant start-up experience.

Jan 1, 2002

By O. R. Bell

In Australia's remote North West are located the operations of Cliffs Robe River, one of the world's largest iron ore projects. Initial project cost was $US300 million and required the construction of a deepwater port, two toms for 3000 people, a 105 Mw power station and 170 km of railroad, all in harsh, arid country over 1300 km from the nearest industrial centre. The ore occurs as goethite cappings on scattered mesas and averages 57 percent iron. All aspects of the project are reviewed from pre-operational research, through project construction to current operation.

Jan 1, 1979

People in economically developed societies demonstrate inherent human care for Earth and want to stop pollution. Yet efforts to clean Earth seem bogged in confusion from wildly contradictory and alarmist predictions of æclimate crisisÆ. Supposed experts openly disagree yet weÆre told thereÆs universal agreement humans are causing æthe end of life as we know itÆ. The turmoil combines with peopleÆs feelings of fear, guilt, anger, hopelessness and even resignation and apathy to trigger æclimate alarmÆ. The paper enables people to rediscover clarity, hope and support for Earth by understanding how climate alarm and confusion were created and how they actually increase pollution. Many people seem to think global warming is as serious as pollution and worry that questioning alarm will enable pollution. Yet theyÆre different. We need be even more concerned about climate alarm because history shows repeatedly that when buried by ignorance and panic real problems grow overwhelming. Environmental credibility is endangered by confused politicians and sensationalist media. When weÆre willing to re-evaluate what weÆve been told we replace fear and confusion with facts and freedom to identify opportunities. Combining this with practical understanding of human behaviour and leadership enables opportunities to be identified and action taken. The paper shows how confident, informed leadership leads and supports higher productivity and effective care for the natural environment.

Jan 1, 2009

By Nathan P. Schmidt

Climate and hydrology data are required during all phases of mining projects, including impact assessment, mine planning and design, operational water management and mine closure and reclamation design. In the Canadian north, data sources are spatially sparse and often short-term in nature, and design parameters are often estimated based on data collected at sites far distant. Confidence in such data can be increased by verification or modification using data collected during properly implemented baseline and operational monitoring programs. A data set that accurately reflects conditions at the project is more readily accepted by regulatory agencies during the permitting process, and allows development of more effective and economic water management, mitigation measures and compensation. Data requirements and collection methods for developing an adequate data set for mine development are reviewed. These are illustrated using examples from oil sands, diamond and metal mines in the Canadian north.

May 1, 2004

By P. K. N. Raghavan

This paper identifies potential technologies for Carbon dioxide abatement from the mining and metal industry with special reference to the Aluminium industry. Mine reclamation could contribute to this effort to successfully reach the greenhouse gas (GHG) emissions reduction commitments for a nation. An overview of GHG production by the mining and metal industry together with a review of principles used to set the context in which specific options for GHG reduction are described. Options for GHG reduction in the mining and metal industry include reforestation, Addition of soil amendments or neutralizing agents, CO2 capture and storage, initiatives towards energy reduction, waste heat recovery and alternative energy use. An analysis and quantification of the potential GHG reduction of potential carbon sinks and sequestration options for the mining and metal industry are provided. Cost estimates for different options are provided. The paper also identifies sources that could fund research regarding GHG reduction options. The paper concludes with recommendations.

Jan 1, 2011