Search Documents

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By J. W. Thompson

This work is a codification and annotation of the Congressional enactments relating to minerals, mineral lands, and mining. It covers every enactment of Congress from the original ordinance of 1785 to the present time, as well as all sections of the Revised Statutes of the United States relating to these subjects. These laws are grouped according to their general subject matter, and are arranged thereunder in numerical or chronological order. Many of the mining statutes include matter not pertinent to the subject, and only those parts of such acts are quoted as will properly show their relation to minerals and mineral lands and indicate how they should be construed. Some mining acts have been repealed or have become obsolete, and others have become incorporated substantially in sections of the Re- vised Statutes; but these are retained in order to show the changes made, and the constructions placed thereon by the courts are given as aids in construing the new or repealing acts. The annotations consist of legal propositions abstracted from the decisions of the various courts and executive officers of the Govern- ment that have interpreted the sections and statutes so codified. These legal propositions are arranged under the different sections and acts with appropriate headings, titles, and subtitles, in logical order, exhibiting the present status of each particular section or act and its application to the subject of mines and mineral lands. The annotations do not purport to be abstracts of decisions on the sub- stantive law of mines and mining generally, but are limited strictly to the interpretation placed on a given section or act definitely re- ferred to by a court or executive officer by the number of the section of the Revised Statutes or the volume and page of the Statutes at Large in which the Congressional enactment is found. It may be observed that the legal propositions stated are not always pertinent to the particular section or act under which they are classed and of which they purport to give a construction. The arrangement, however, is not an arbitrary one, but is so made for the reason that the courts or officers in the construction of a particular section or act definitely referred to by number or volume and page incorporated in the decision matter not strictly pertinent to the par- ticular section or act so designated. This statement applies especially to the interpretations placed on the sections of the Revised Statutes. The decisions abstracted for the purpose of this work are those of the United States Supreme Court, 234 volumes; the various Federal courts, 214 volumes; the decisions of the Department of the Interior

Jan 1, 1915

By Albert H. Fay

This glossary is publi~hed- by the Bureau of Mines as a contribution' to the mining literature in the belief that it will fill a long-felt need. It contains about 20,000 terms; these include both technical and purely local terms related to metal mining, coal mining, quarrying, petroleum, and natural gas, and metallurgical works; names of useful, important, and common minerals and rocks; an<lgeological terms. It presents in one comprehensive volume the available standard, technical terms relating to the mining and mineral industry, as well as provincialisms that have been or are now in use in English-speaking countries. The glossary also includes many terms relating to ceramics and the clay industry, glass making, foundry practice, railway and building construction, electrical installation and power-plant equipment, and chemical terms relating to metallurgical practice. Complete lists of terms for' each of these allied industries are beyond the scope of this glossary. Paleontological terms, although closely associated with geology, are far removed from mining and metallurgical operations, and for this reason have been omitted. In a compilation of this magnitude, it is difficult, within a reasonable time to verify all definitions as to the latest usage. Much verifying was done and it is hoped that the best and latest definitions have been used. Reference to the publications cited will enable the reader to determine approximately the period when the definition was used. Definitions in use by engineers of high national or international reputation are given first preference. When definitions from different sources are the same, credit is given to the earlier author as being the original or nearest to the original source. Immediately following each term the name of the locality wherein the word is presumed to have originated or is widely used is given, where such information is available. The name of the author or source from which the definition was obtained follows the definition, and serves as a key to the publications listed. The terms selected from the various glossaries and publications examined have been compared with the Webster,

Jan 1, 1920

By C. G. Storm

Permissible explosives are those that have passed the tests pre- scribed by the Bureau of Mines for explosives intended for use in coal mines, and are therefore recommended by the bureau as suitable for this class of work when used under the prescribed conditions. The tests for permissible explosives and the conditions prescribed for their use are described in Miners' Circular 6 of the Bureau of Mines. Up to June 1, 1915, 168 explosives had been classed as per- missible explosives; 133 of them were then on the bureau's "per- missible list" and 35 had been withdrawn by the manufacturers. In addition to the required physical tests, each explosive is sub- jected to a complete chemical examination in order that its exact composition may be known and also that the composition of future samples of the same explosive collected in the field may be compared with that of the sample which originally passed the bureau's tests, for by such comparison it may be possible to ascertain whether or not the explosive as supplied to the miner is still "permissible." This bulletin is published primarily for the purpose of informing manufacturers of such explosives as to the methods used by the Bureau of Mines in the analysis of samples received for tests to determine their permissibility. Such information may be of value in cases of possible controversy over the results obtained in the analysis of a field sample as compared with those obtained in ana- lyzing the sample originally tested by the bureau. Also, a descrip- tion of the methods used by the Bureau of Mines in the analysis of explosives should be of assistance to the many chemists engaged in similar analytical work.

Jan 1, 1916

By J. A. Holmes, EDWARD C. FRANKLIN, RALPH A. GOULD

The commission may be permitted to express its earnest hope that the litigation which comes to an end with the findings and recom- mendations herein set forth will be considered by both parties to the action as definitely and equitably decided. The commission trusts that its work will show the value of the commission form of settlement and that its work will serve as a prece- dent to be followed in disputes relative to technical subjects. If the work of the commission is productive of a tendency on the part of technical litigants to avoid the use of the courts for the settlement of disputes it will not have been done in vain. Such tendency will surely grow and ultimately such differences will be arbitrated by technically trained men without recourse to the courts of law. Appended to the report of the findings of the commission are to be found the detailed reports covering the several lines of inquiry and investigation carried on by the commission and upon which its findings are based, and also a detailed statement of the fiscal affairs of the commission. A word of explanation is necessary in regard to the fiscal statement. While each party to the litigation has agreed to bear one-half of the expense of the investigations of the commission, it will be noted that the Selby Smelting & Lead Co. is credited with $21,000, while Solano County is credited with but $6,000. In order that the investigations of the commission might go forward without interruption the Selby Smelting & Lead Co. has generously supplied funds at the times they were needed. This assistance has been

Jan 1, 1915

By R. Y. Williams

In this report an attempt is made to discuss the first cost of each of several types of mine-ventilation stoppings, as well as the total annual expense of maintaining a stopping during its required period of service. Such data furnish a basis for comparison of the efficiency of the different types, and are of great importance to an engineer planning the development of a mine. The data given were obtained through an investigation conducted under a cooperative agreement between the Bureau of Mines, the Illinois State Geological Survey, and the department of mining engineering of the University of Illinois. The report itself is published by the Bureau of Mines as a contribution to the literature on safety and efficiency in coal mining.

Jan 1, 1915

By Nathaniel Herz

PARTING of bullion before shipment to the mint had been considered by the Homestake Mining Co. at various times, but had never been attempted before 1933, be- cause the margin of profit appeared to be too small to warrant the complications in refining. When the gold standard was abandoned by the United States in the spring of 1933, however, parting of the bullion was decided upon. The method selected was the Miller or chlorine process, which consists of the passing of gaseous chlorine into a bath of molten bullion, converting all metals other than gold into chlorides, and remov-

Jan 1, 1935

THE BULOLO gold-dredging operations were described at some length by Frank W. Griffin at the Oct. 11 meeting of the San Francisco Section. This enterprise is on the island of New Guinea, about 1800 miles north of Sydney, Australia. The area in which the present placers exist originally was German territory but later the location was taken over by Australians. Gold was discovered in 1923 by prospectors who required 8 to 9 days to pack into the country over severe mountain trails. In 1926 a rich discovery was made on Edie Creek and in 1927 the deposit on the Bulolo River was discovered.

Jan 1, 1932

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

THE term mountain bump describes the sudden rupture of one or more coal pillars under excessive stress. These bursts occur with varying degrees of violence and sometimes include adjacent strata, especially the bottom rock. Many failures do not develop enough violence to be dangerous and are regarded as an aid to coal production, but severe occurrences are accompanied by tons of flying coal, dense clouds of dust, and excessive gas emission. Such bursts sometimes throw heavy machinery several feet. Major factors to be considered in the problem are the nature of the strata above and below the seam and the depth of cover. Bumps are classified as to their nature, extent of damage, and point of occurrence, e. g., face bump, coal bump, high side bump, low side pavement bump, and district bump.

Jan 8, 1958

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer&apos;s recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free&apos; from folding and faulting.

Jan 1, 1935

By Walter Herd

For the past eight years, No. 2 mine of the Cumberland Railway & Coal Co., Springhill-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Depart~ of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. °This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room-and-pillar method was employed, and in January of that year (there being a cessation of work from March to August due to labour troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine, was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In ?the interval, development work for longwall retreating below the 5,900-foot level was vigorously pushed.

Jan 1, 1929

By H. D. Brenk

"The German Federation of International Mining and Mineral Resources (FAB) is a federation of German companies that are active in international mining and mining related business. The FAB presents a platform for the exchange of information about the worldwide mining commodities in the dialogue with German and foreign institutions. The expertise of the member companies in mining and related activities is based on a long term operation and consulting experience in Germany and abroad. This forms the basis for the special international competitiveness "Made in Germany". The FAB is particularly engaged in the following topics and tasks and acts as a focal point for: • international project developments with the German mining industry, • sustainable mining, consulting and equipment services, • geological and environmental technologies, • project financing and • intermediation of contracts, project enquiries, professional symposia and events. The FAB acts as a contact- and coordination site for international business partners, organizations and governmental authorities. Together with the federal government the FAB organizes bilateral working group meetings in the commodity and mining sector. Project enquiries are being distributed from the FAB among their member companies."

Jan 1, 2011

By N. J. Sather

The history of the Bunker Hill mine dates back to August 26, 1885, when Noah S. Kellogg found the outcrop of the Bunker Hill orebody on the hillside of Milo Gulch above the present town of Wardner, Idaho. A small concentrator was erected in 1886, and before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d&apos;Alene Lake. After ten years of production, an interest was purchased in the Tacoma smelter at Tacoma, Wash., to which the entire output was shipped. In 1916 and 1917, a modern lead smelting plant and refinery was erected, and a modern electrolytic zinc reduction plant was built in 1927-1928 by the Sullivan Mining Co. which was 50 pct owned (and now totally owned) by the Bunker Hill Co.

Jan 6, 1961

By Jerry Dolph

In September 1855, 55-year-old Noah Spencer Kellogg and his $3 jackass named Bill discovered what was known at the time as a “blow out” of high-grade lead and silver ore. The deposit was located on the side of a North Idaho mountain high above the South Fork of the Coeur d’Alene River. The ore was later assayed at 41,141 g/t (1,200 oz/st) silver. Kellogg named his discovery the Bunker Hill Lode, after the June 17, 1775 Revolutionary War battle of Bunker Hill. A thriving pioneer settlement sprang into existence around the resulting mine’s workings and was eventually— and appropriately — named Kellogg. The peak rising hundreds of feet above the mine’s adit was named “Jack-ass Peak” after Noah Kellogg’s hairy companion.

Jan 1, 1996

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020

By G Chitombo, M Ruest

In surface mining, studies of the kinematics of blasted rocks using high speed film/video image analysis have allowed the estimation of the starting time, direction and magnitude of visible movement of fixed sections of the free face. Horizontal displacement versus time plots from discrete targets at the face generally report changes in slope over very small time intervals. These changes indicate step increases in velocity due to the action of explosive gases. In practice, the onset of rock mass movement, different to localised spalling, has been associated with a response time which exceeds the combined times of detonation, propagation and reflection of stress waves. This time is referred to as minimum response or burden movement time. As an engineering index, burden movement time has been used to provide guidelines for the selection of inter-hole and inter-row delay sequences in production blasting. With respect to improving breakage and fragmentation, it has been demonstrated that the delay interval between adjacent explosive charges should be less than the expected burden movement time. Similarly to reduce confinement between rows, delay intervals should exceed the expected burden movement time. The Hybrid Stress Blasting Model (HSBM) is a modelling framework that dynamically links an ideal and non-ideal explosives detonation code to a geomechanical rock model. This blast simulation tool is aimed at analysing the role played by different explosive formulations in fragmenting and/or damaging various rock types under different degrees of confinement. In the current framework, the rock behaviour under extremely high pressures and loading rates is calibrated from shock tests and the role of the explosive in fracture growth is accounted for and assumes a compressible fluid flowing through the explicit fracture network. The model is being developed as part of an international collaborative research project funded by a consortium of companies comprised of explosive and equipment suppliers and major mining houses. As part of the development and validation of the HSBM project, data from literature addressing the kinematics of the rock mass (ie burden displacement, face velocities and response times) has been collated and used to evaluate the current version of the code. A series of numerical experiments have been conducted with the view to: evaluate the response of the rock mass to changes in burden distance given by the impact of both stress waves and radial gas flow pressure;compare the modelling outcomes in terms of displacement, response time and face velocities to documented field observations; andcompare stress induced and stress/gas induced modes in terms of burden displacement outcomes. Results from these experiments have shown that in its current form the model is able to capture the trends observed and measured in practice. This is with respect to the simulation of burden displacement, response time and average face velocities for different geometries and charging conditions. The experiments have served as consistency checks which form part of an ongoing and comprehensive evaluation and validation of the HSBM code also aimed at addressing some of its current limitations.

Jan 1, 2007

By A. C. Emery

The physical and chemical properties for the metalliferrous feed materials to the Imperial Smelting Process blast furnace are defined and the means of achieving these properties by the sintering or briquetting routes discussed. Modern sinter plant performance data is included with a plant flow sheet showing draughting patterns. The necessity for ensuring an adequate SO2 content in sinter machine gases when roasting sulphide materials to enable conversion to sulphuric acid in a contact acid plant is described. The ability of the process to consume limited quantities of oxide materials, residues from other processes and other secondary sources is discussed. The argument for a briquetting route is developed out of this limitation and the merits of cold and hot briquetting examined. Development work on the hot briquetting route for this purpose is briefly described and several flow sheets outlining possible applications for hot briquetting to different raw material situations including the preparation of low lead charges for the furnace are presented.

Jan 1, 1977

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019

Most text books on rock blasting claim that the relationship between burden and borehole diameter is linear. The statistical calculation presented here with real values from one hundred open pit and underground mines indicates that the relationship is exponential. For underground mines the burdens are consistently lower than those for open pit mines because of higher ore densities, greater confinement in blasting, and finally greater demand for well fragmented rock. The results shown in this paper are recommended to be considered in basic teaching of rock blasting technique. The formulas can be used for a first rough estimation of practical burden and spacing. The formulas do not however give any information about the fragmentation. For that purpose it is necessary to use other formulas not described in this paper.

Jan 1, 1990