Search Documents

By David A. Bacca

Hydraulically powered submersible borehole dewatering pumps and emulsion/ANFO blends evolved at about the same time and for the same reasons. Mining operators needed safe, efficient dewatering systems and water resistant products.

Jan 1, 1994

By B. P. Boisen

INTRODUCTION Application Measurement of rock deformation is essential to stability and behavioral monitoring of underground openings. The difficulties of obtaining adequate sample distribution, density, and orientation can frequently be overcome by the use of single and multiple position borehole extensometers. In its simplest form, a borehole extensometer consists of an instrument head, usually anchored in the collar of a borehole, and a number of in-hole anchors, each of which is fixed in place at a known distance from the collar. As rock adjacent to the borehole deforms, the component parallel to the borehole direction causes a distance change between adjacent in-hole anchors, as well as a distance change between individual anchors and the instrument head. These changes are measured by means of a mechanical link (usually wire or rod) extending to the instrument head from each anchor. The resulting data can be used to compute the distribution, magnitude, rate, and acceleration of deformation in the material intersected by the extensometer's borehole. Wire Vs. Rod Extensometers Since the early 1960s myriad varieties of borehole extensometers have become available through the combination of various special features of two basic instruments, the wire and rod versions of borehole extensometers. Recent publications have recommended shallow depth limitations for wire extensometers, and favor rod extensometers for a broad range of borehole inclinations and depths. There are three main reasons for using a deep wire system: its cost effectiveness; the fact that tremendous depth means tremendous rod weight which will cause the rod to buckle or rub against the borehole or casing wall; and users' attitude and proper understanding of how to install and apply a wire-type extensometer. Here experience plays a big role. Over the years, many have learned the hard way that untensioned rod extensometers are simple and inherently inexpensive, but limited to vertical up holes where sensitivity is not influenced by friction between the rod elements and the borehole wall or protective conduit, the inertia of the rod elements, or the direction of the movement to be measured. In deep, horizontal, or inclined holes, and in instances where compressive as well as tensile strains or displacements are anticipated, tensioned rod or wire systems are preferred. System Components Borehole extensometers are made up of at least the following five principal components: the instrument head; the collar anchor assembly; the downhole system of anchors and rods or wires; the signal cable if the head is equipped for electronic readout; and the readout apparatus, whether mechanical or electronic. These components are shown in Fig. 1. Borehole Requirements Most extensometers are designed for installation in nominal 75 to 57-mm (3.0 to 2.25-in.) diam drill holes. Either a diamond drill or a percussion drill hole is satisfactory, provided the variation in drill-hole diameter is within the tolerance of the standard anchor design. The basic system may be modified for other hole diameters by changing the dimensions of the collar anchor and downhole anchor assemblies. Some instrument heads and collar anchor assemblies require enlarged borehole collars, though usually not over 150 mm (6 in.) for a depth of 1 m (3 ft). It is desirable, although not essential, that holes be free-draining. Holes must be clean and free of debris before installation. Depth/Orientation of Extensometer Boreholes Extensometers are designed to measure axial strain components in the instrumented drill hole. As the drill hole is axially deformed, the distances between individual downhole anchors and the instrument head change, as do the distances between adjacent anchors. The distance changes measured by a multiple position borehole extensometer, for example, are reduced to functions of time, hole depth, anchor position, or other parameters of significance in terms of the structure under investigation.

Jan 1, 1982

By Kyle Ott, Bernard Daly, Syed Haq, Douglas Anderson, Parsons Brinckerhoff

Drill and blast was determined to be the most cost-effective means of excavating the Raw Water Tunnel (RWT) for the Croton Water Treatment Plant in the Bronx, New York City. One of the major issues confronting project designers was the potential impact of blast vibrations on a major City Distribution Tunnel (CDT). The proposed path of the RWT would cross less than 30 meters (100 feet) above the CDT, which was built in 1917. Discussions with New York City Department of Environmental Protection led to vibration criteria on the CDT of 51 mm/sec (2 in/sec) peak particle velocity as an alert level, and 38 mm/sec (1.5 in/sec) as a review level.

Jan 1, 2012

By C. J. Mwenifumbo

Preservation of groundwater quality is a major environmental concern. The disposal of hazardous material from urban waste dumps, milling wastes in tailings ponds, and industrial wastes in injection wells may contaminate potential sources of potable groundwater. The containment or migration of contaminants in the subsurface depends on bedrock characteristics and type of overlying sediments. Fractured bedrock and permeable sediments that may provide pathways for the transport of potentially harmful contaminants should be avoided when selecting a disposal site. The role of borehole geophysics in hazardous waste-site investigations is reviewed in three categories: (I) site selection; (2) determination of the extent of contamination at existing sites; and (3) long-term monitoring of migration of contaminants. In the first category, borehole geophysical techniques developed for lithology and fracture identification, and for porosity determination, provide some of the necessary information for understanding the subsurface hydrogeology. Lithological information can be obtained from gamma-ray, electrical resistivity, induction, magnetic susceptibility, and sometimes induced polarization logs; fracture detection and characterization can be accomplished with the use of caliper, density, resistivity, temperature, and acoustic televiewer logs. Estimates of porosity are derived primarily from neutron-neutron, resistivity, density, and soniclogs. Borehole geophysical techniques used in water quality determinations include self-potential, fluid resistivity, Eh (redox potentials) and pH measurements, and these can be used to map the extent of contamination at an existing waste site. Cross borehole and borehole-to-surface electrical methods can also be used in this application. Long-term monitoring of contaminant migration in boreholes can be accomplished with techniques that respond to changes in electrical conductivity, temperature and fluid chemistry caused by the presence of contaminants.

Jan 1, 1993

By J. G. Kelly, C. P. Brown

"In June 1983 a new borehole hoisting system was commissioned at Sherritt Gordon's Fox Mine. Twelve hundred tons-per-day of ore from the 2600 and 2800 levels are being hoisted to the 2000 level through an 8-jt diameter bored winze. This new method replaces the diesel truck haulage system which had been in operation at the mine since 1975.A study was initiated in 1980to determine the most effective method of achieving the required production. The study examined several hoisting alternatives including: expanding the existing trucking system; converting to electrically -powered truck haulage; and deepening the skip compartments of the existing main shaft. The alternative selected as the hoisting method most suited to the requirements was borehole hoisting.Development of the new system commenced in April 1982. Underground excavations included 700 feet of 8-ft diameter borehole, a hoistroom and headframe, storage bins, and a grizzly and rockbreaker station. Equipment installations included: a 5-ft diameter double-drum Nordberg hoist; a counterweighted Kimberley-type skip; two rockbreakers; and the steel sets in the winze. These installations were completed in June 1983. Some problems were encountered after the initial commissioning but these were solved, and since August 1983, the system has proven that the designed capacity is achievable within expected costs."

Jan 1, 1985

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By Tom Palangio, Ralph M. Olmstead

Video inspection of boreholes with cameras developed specifically for the mining industry is now possible. These designs are reliable, cost effective, and have the flexibility to be used in other applications.

Jan 1, 1998

By Roger L. King

The Bureau of Mines has developed probes to be used in emergency mine rescue operations by being lowered through a borehole drilled into an underground mine. Various probes can provide two-way voice communication with trapped miners, continuous mine atmosphere monitoring, temperature indication, and television searching capability. At present, an infrared imaging probe is being developed for "seeing" through coal smoke.

Jan 1, 1976

By James K. Hallenburg

Geophysical borehole logging is a valuable and inexpensive tool for coal deposit evaluation, development, and production. In addition to the usual determinations of depth and seam thickness, geophysical borehole logs can effectively and accurately determine the coal ash, moisture, and heat contents in situ. Location and evaluation of the partings can be done quickly and accurately. Overburden character determination, such as roof competence, dewatering parameters, ripability, trace element content of the coal and overburden, and sulfur content can be done with existing tools and techniques. The quality of such determinations depends upon the quality of planning and calibration.

Jan 1, 1984

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By George A. Savanick

Borehole (slurry) mining, in which a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a Bureau of Mines program to increase the domestic availability of critical minerals. Approximately 1700 tons (1.54x106 kg) of phosphate ore were mined at 40 tph (10.1 kg/s) from a depth of 250 ft (76 m). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1983

By G. A. Savanick

Borehole (slurry) mining, where a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a US Bureau of Mines program to increase the domestic availability of critical minerals. About 1.5 kt (1700 st) of phosphate ore were mined at 23.6 t/h (26 stph) from a depth of 76 m (250 ft). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1986

By Gregory Abramov

Borehole Mining (BHM), a remotely-operated waterjet mining method (Figure 1), has recently achieved two major milestones. It was, for the first time, applied to the extraction of manganese ore and at temperatures below freezing. The 1St stage is a demonstration test that is now underway just north of Emily, Minnesota, where the manganese ore is located 100-160m below the surface and its reserves are estimated to be in excess of 500,000 tons. The deposit was discovered over 60 years ago but, due to the fragile and sensitive nature of this Land of 10,000 Lakes (nickname for the State of Minnesota) and strong environmental restrictions, the iron/manganese reserves were deemed unrecoverable and remained untouched until late 2010 when permission for a single-hole demo-test was issued by the local Department of Natural Resources.

Jan 1, 2011

By M. F. Dibble

The technology available for mining of underwater mineral resources such as placers and phosphorite, typically occurring with variable amounts of overburden, has remained largely unchanged for decades. The traditional bucket ladder dredge with maximum digging depth of 48 m and monthly capacities about 500,000 m3 still reins as the only heavy duty mining system capable of working the tough materials characteristic of heavy metal placers. Attempts at adapting the bucket wheel cutter-suction dredge to these severe conditions have not yet been successful except in moving small volumes from shallow depths. High capital cost (20-30 million U.S. dollars), high cost of overburden removable, and turbidity generation for the bucket ladder are often significant negative factors in mining operations where this system remains the only viable alternative. The Japanese continue to advance the technology of their submersible dredge pump system powered by specially adapted, direct drive electric motors. Present systems are designed primarily for working surficial deposits of aggregate to depths as great as 90 meters, the pump suspended by cable from a surface vessel with an eductor pipe leading from the pump to the vessel. Such a system may prove adaptable to a variety of surficial deposits including phosphorite, shell and heavy minerals in addition to aggregate. However promising for the exploitation of surficial deposits, little advantage can be expected for the deeper buried and more difficult deposits.

Jan 1, 1986

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

Provide a means for reliable in situ stress change measurements in soft, friable geologic materials under high stress. Background Effective mine design requires a knowledge of changes in rock stress generated by a mining operation. In situ stress measurement can provide a means of obtaining this knowledge from an active mine for the ultimate purpose of design verification and analysis. The Bureau of Mines has designed and tested a device for measuring changes in rock stress-the borehole platened flatjack (BPF). It has found application in investigating stress anomalies due to geologic structures, stress concentrations from multiple seam interaction, and stress abutments from pillar retreat and longwall mining.

Jan 1, 1990

The No. 2 Ore-shaft, at Mount Isa Mines Limited, involving the use of boreholes as ropeways for the upper portion thereof, constitutes, we believe, a unique feature in hoisting installations. The boreholes were sunk from the surface to a depth of 390 ft., thus eliminating the necessity of erecting the hoist at an underground location or construction of the shaft for this distance. Fig. 1, a diagrammatic cross-section through the shaft, shows the complete installation from the surface down to the first loading station below No. 7 haulage level.During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impracticable and uneconomical to continue deepening it to serve haulage levels below the present No. 5-level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5-level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin.Referring again to Fig. 1, it is apparent that the section above No. 4-level, if opened out to full shaft size, would be inoperative and would serve no useful purpose except, possibly, as a ventilation duct. Original plans therefore did not include continuation of the shaft above No. 4-level. Excavation of a hoist room upon No. 5-level; erection of sheave wheels just below No. 4-level, and a long inclined ropeway leading from the hoist to the sheaves, were incorporated in the general layout. Work on the lower sectionof the shaft had started when the idea of locating the hoist...

Jan 1, 1939

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By A. W. Jenike

Mine backfilling is a desirable method for the disposal of retorted oil shale. Hydraulic, mechanical and pneuna.cic transport and stowing methods were investigated, and the mechanical transport and stowing method using conveyors was selected as the most promising system. Transport of retorted oil shale at the rate of 3000 cons per hour (2700 t(h) to the backfill level, situated about: 2000 feet (610 m) below surface, with skips or conveyors is uneconomic. Hence, borehole transport utilizing gravity flow was investigated. This paper describes the theory of flow, flow properties of retorted oil shale, and the design of a borehole and hopper system.

Jan 1, 1978

By Nicholas M. Short

Many a geologist or driller has wished he could somehow climb into a borehole to see for himself what fractures looked like. Or why recovery was poor. Or how the bit was actually lost. Now it is possible to do the next best thing to climbing into the hole. TV cameras are being used for a close-up look at borehole conditions. Ever since television was invented, geologists and others interested in subsurface conditions have wanted a TV camera that could be used in the narrow confines of a borehole. But development of such a camera was slow, mainly because of the need for compact size. Not until the late 1950's did the technology of electronic miniaturization develop to a point where a camera satisfactory for the purpose could be put together.

Jan 1, 1963