Search Documents

By Yoginder P.

ACKNOWLEDGEMENTS Authors sincerely appreciate the interest, cooperation and technical support of the coal company management and staff in conducting the study. Without their assistance this study would not have been possible. INTRODUCTION AND SPECIFIC OBJECTIVES An area in the midwest overlying abandoned room-and-pillar mine workings at, shallow depth has been experiencing subsidence movements with associated damage to surface structures. Other coal companies in the area have also been having similar experience. A 16 - month cooperative study between a mining company and the Department of Mining Engineering at SIUC was developed with the following objectives. 1) Determine the extent to which surface and subsurface movements were complete in the area, 2) Identify the mechanism(s) of subsidence in the area, 3) Determine the influence of geology and hydrology of the area on subsidence movements, 4) Observe the conditions of abandoned underground workings with a borehole TV camera, 5) Characterize the extent of damage and monitor possible progressive damage to selected surface structures, and 6) Make recommendations to a) minimize further damage to surface structures in the area, b) identify future areas that may be affected by these movements and c) modify mining systems to minimize these movements.

Jan 1, 1986

By L. Barry Phelps

Coal mine drainage, which occurs predominantly as acid mine drainage in the East, is a serious contaminant of surface and groundwater systems (Appalachian Regional Commission, 1969). Treatment of this pollutant can be very costly and is often difficult to achieve (Appalachian Regional Commission, 1969). A major source of coal mine drainage in surface waters is polluted ground- water discharge, therefore treatment of surface water does little to combat groundwater contamination. Prevention of the formation of coal mine drainage and restricting its entrance into the groundwater protects both surface and groundwater systems. The formation of acid mine drainage may be inhibited by preventing contact between toxic spoil, air, and water (Grim and Hill, 1974). This may be accomplished by surrounding toxic spoil with a relatively impermeable barrier, thus restricting groundwater and oxygen flow through the toxic zone. Toxic spoil packages constructed in this manner would minimize the entrance of acid mine drainage into the groundwater system, allowing dilution by uncontaminated water to occur. If successful, concentrations of coal mine drainage would be reduced below toxic levels.

Jan 1, 1981

By Brian S. Prosser, Ian J. Duckworth

With the trend in the coal mining industry pushing towards improved productivity and greater production, the number and size of longwall panels is increasing rapidly. The development and mining of large longwall panels causes unique problems in the provision of adequate ventilation at the working faces. Because of the transient nature of the longwall panel, and the difficult field conditions for ventilation measurements, detailed pressure and volume surveys are often not conducted around the longwall circuit. This is unforlunate because the highest resistance airway in longwall mines is typically the longwall tailgate, which frequently represents the only unregulated split in the ventilation network. This paper examines data collected from ventilation studies of longwall panels at nine mines. The variation in airway resistance, ventilating pressure and airflow is examined and compared with specific factors such as airway dimensions, ground conditions and support type used.

Jan 1, 1997

By D. Malhotra

The number of variables which can effect flotation of molybdenite is very large. This paper discusses the effect of two operating variables, namely, the degree of aeration and agitation, on the grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." The analysis of flotation results indicate that molybdenite can be characterized into fast-floating and slow-floating components. The rates of fast-floating components, which do not create a problem in flotation, could be varied by changing agitation of airflow rates. However, the rate of slow-floating components was stable and was only a function of residence time in the float machine. The degree of aeration has a significant effect on the grade of MoS2 with only a slight effect on the recovery of MoS2. The degree of agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits is subsequently discussed.

Jan 1, 1977

By Harold W. Scott

Geological Engineering is now a recognized curriculum in most of the mining schools in United States. Graduates of these schools are scattered over the face of the earth, participating in exploration and mining enterprises of diverse character. They are engaged in the mapping of new mineral deposits, in the extension of old deposits, the estimation of reserves, microscopic analysis, and in the direction of exploitation and conservation of man's natural resources. The training of men qualified to carry out these technical phases of modern industry has fallen essentially to the mining schools. For the most part they have met the demand for technically trained men in the mineral industries. Schools Offering Geological Engineering Degree The mining schools have passed through the early stages of their development and at the present offer varied curricula covering the fields of geological engineering, mining engineering, and metallurgical engineering. Usually a B.S. degree is offered in any of these three fields. However, .there has been some tendency of recent date on the part of the Engineers Council for Professional Development to question the validity of a B.S. degree in Geological Engineering. The of this paper is to examine the curricula as offered in the mining schools, to evaluate their engineering content, and to propose minimum requirements for the degree of Geological Engineering in the mining industry. The curricula of eight institutions that offer the degree of B.S. in Geological Engineering or Mining Geology have been studied (Table 1). All except one of these schools are in or near mining districts and occur west of the Mississippi River. They are all state-supported institutions that have come into existence because of the state's need for technically trained men. A graduate from .a mining school is called upon to perform many duties of a technical nature. His initial task may be to make a geological map of a mine or the surface above, but before the map is finished he may be asked to take over the responsibility of getting the ore "on top." And finally, he might find it essential to know how to mill the ore. Certainly this requires technically trained men and the mining schools are essentially the organizations to do the job. The departments of geology in these schools are training geological engineers. Field Of Geology If we were to accept the opinions of some writers, we would be forced to conclude that all geology departments offer only a "dilettante" variety of subjects.

Jan 1, 1944

By J. Mutmansky, C. Lee

"The size distribution of coal mine dust is one of its most important characteristics because the particle size is known to govern the region of deposition of dust within the human respiratory tract. In addition, dust characteristics, particle settling rate, transportability of the dust and the efficiency of dust control measures are all affected by the particle size. As a result, particle size distribution of the airborne dust in a coal mine is a fundamental property that impacts on the health of underground workers.This paper deals with some basic findings on the size distribution of cool mine dust based upon the results of data collection in six underground coal mines using continuous miners. All airborne dust sampling was performed on development sections using eight stage cascade impactors and permissible 2. O l / min pumps. Samplers locations were fixed in the sections with respect to the continuous miner and roofbolter or with respect to the intake and return airways • Sampling times varied from 45 minutes to 6 hours , depending upon the dust concentration. The first topic of analysis was the test to determine whether the commonly used lognonnal distribution is valid when applied to airborne coal mine dust. Secondly, the conventional method of representing the· distribution using two parameters, the geometric mean and the geometric standard deviation, is questioned. Since almost all size data were found to show some degree of bimodality, the two parameter lognonnal distribution may not represent the total airborne coal mine dust size , quite adequately. Bimodal lognonnal distribution was tested to be a good approximation in the case with two modes in the size distribution.The final topic discussed in this paper is the 'locational variation of the airborne dust size distributions within the continuous mining section. The size distributions varied considerably at the different sampling locations with the continuous miner and roofbolter producing the coarser distributions. Fine size modes in the range of 2 to 4µ m including mostly respirable dust particles were present in almost all samples • Second dust generating sources such as the shuttle car movement were found to be major causes of high respirable dust concentrations in some cases ."

Jan 1, 1988

By J Janus, J Krawczyk

Local accumulation of methane in workings of a longwall is one of the most common causes of mining accidents. This gas has many sources: it may leak from goaf through permeable sealings, or through gaps between roof support sections. This stream is then mixed with ventilation air. In the case of auxiliary ventilation ducts, or free jet fans, we have to consider the propagation of a clean air stream in areas with an air-methane mixture. Therefore, modelling the mixing process of methane with ventilation air is important for determining the hazardous areas and thus to ensure safety. Computational fluid dynamics (CFD), specifically the finite volume method, provides tools for such modelling. However, this method requires validation. For this purpose, we have compared measurements with simulations for selected test cases having sufficient similarity to the present problems. In typical methane explosion hazard areas, such as a longwall, it is difficult to make measurements sufficiently to confirm credibility of 3D CFD simulations. As a relevant alternative, an injector methane drainage station placed in an underground gallery has been selected. The stream of drained goaf methane is entrained by compressed air powered injectors and then mixed with ventilation air. Research in this area does not interfere with mining operations, it can be performed safely in a repeatable way. Flow within the site has many similarities to conditions in mine drifts of the longwall area. Comparative research of measuring the methane concentration distribution in the mine drift downstream injector station, with simulations of propagation of the methane stream, was carried out. For measuring the methane concentration distribution in the mine drift a multipoint measurement velocity system developed at the Strata Mechanics Research Institute was used. For the simulation a finite volume method for turbulent flow of gas mixtures was applied. Preliminary results of comparison are shown as graphs and tables.CITATION:Janus, J and Krawczyk, J, 2013. An analysis of the mixing of air and methane in the stream produced by the mine injector station - Presenting preliminary results of measurements and modelling, in Proceedings The Australian Mine Ventilation Conference , pp 49-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

An extensive series of tests was carried out on a ball mill-rake classifier circuit in the New Broken Hill Consolidated Ltd. concentrator. The data were used to develop a mathematical model of the operation of a rake classifier and this model has been used in the simulation of the performance of a ball mill-rake classifier circuit on a digital computer. As a result of this simulation it has been possible to develop a technique for the optimization and control of a circuit which includes these units.

Jan 1, 1967

By Lynce AJ

A method has been developed for the prediction 'of 'the- . performance of a multi-stage grinding=cyclone classification circuit of any degree of complexity on any ore for a wide range `of operating conditions, The-.method involves ;the. s` inu ation b'f the circuit on a digital computer by means of. matheinatical' models ":bf the"' individual units:, the. development of which is- also discussed'., At present, in order to establish 'the!'" charac'teristtics of they ¦ore- and the machines. in mathematical terms;. it is necessary to know'the performance of a , simpl,.e. ; system on tri.e ore - for! one known ,,feed rate and.fe.ed s,l-zing, analysis. ' ,Fiiither work on :the- separate identification 'of the terms defining the characteristics of the ore and the machines may permit the method to be, applied directly to the cj.4ta,derived from small scale tests on ores,

Jan 1, 1964

By Lynch A. J

A method has been developed for the prediction of the performance of multi-stage grinding-cyclone classification circuits of any degree of complexity on any ore for a wide range of operating conditions. The method involves the simulation of the circuit on a digital computer by means of. mathematical models of the individual units. At present, to establish the characteristics of the ore and the machines in mathematical terms, it is necessary to know the performance of a simple system on the ore for one known feed rate and feed sizing analysis.Further work on the separate identification of the terms defining the characteristics of the ore and the machines may permit the method to be applied directly to the data derived from small scale tests on ores.INTRODUCTIONThe cost of preparing metalliferous ores for concentration processes by, grinding and classification frequently represents a major portion of the cost of treating such ores, and it is necessary both from an economic and a metallurgical point of view that grinding and classification circuits should be operated at their optimum efficiency. It will be realized that the processes carried out in all units in such circuits behave according to physical laws and, if a mathematical representation of the laws applying to each unit could be derived, optimization of the overall process for any given conditions of feed or product may not be difficult.The physical processes in both tumbling mills and hydraulic classifiers are extremely complex and do not appear at present to be amenable to a rigorous mathematical analysis. However, empirical mathematical models of grinding units which have been presented previously (Callcottand Lynch, 1963; Lynch and Moore, 1963) may be used to discuss the operation of the grinding units in multi-stage circuits. Another type of model, which leads to a reasonable...

Jan 1, 1965

By S. M. Moore

Each year more than 400 coal miners are injured (fatal and non-fatal) by rock falling from between or around roof supports. Many of these injuries could be prevented by the installation of roof screen (wire mesh). However, many coal mines may be reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential saving in workers? compensation (WC) premiums that could be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by IL and KY were investigated in this study. Using actual data obtained from MSHA, national and state WC bodies and individual insurance companies (e.g. average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), hypothetical mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state?s actual WC rate-setting formulas, total savings in WC costs after a three-year period were determined. Across both states, savings in WC premiums ranged from 1.8% to 14.6% when injuries were reduced by 10% to 20%. Additionally, an economic analysis was performed for an existing mine consisting of 67 employees. For this mine, the annual cost of a roof screening program was estimated at $240,000. If the screening prevented 13 ?struck by? WC claims over a 3-year period at this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By D. G. Krige

Using chip sample data and spatial structure parameters from a large mined-out section of a South African gold mine the advantages to be gained from a regular underground borehole drilling programme have been investigated for short- and medium- to long-term planning based on block valuations. The results have been compared with the current position, which relies invariably on the extrapolation of limited peripheral sampling data from raises, gullies or stope faces. Some preliminary work has also been done regarding the implications of such underground drilling on costs used for the present pay limit calculations. The results of the study, though preliminary, show that the net advantage of advance regular underground drilling could be substantial and that a more intensive follow-up research is warranted.

Jan 1, 2003

During the 1950's there was a flurry of activity on the design of main ventilation shafts for mines. More recently, a new ana- lysis was commissioned in relation to the multi-shaft, nuclear waste isolation facili- ties currently under design in the United States. This paper presents the major find- ings of that study and should prove of value as a reference in the design of proposed new shafts. An overview of mine shaft resistance introduces the effects of the shaft walls, fittings, conveyances and shaft stations. Each of these is analyzed in turn. A com- pletely new technique is described, which facilitates the estimation of wall resis- tance. The effect of size of a conveyance is quantified and shown to be dominant when the cage occupies more than 30 per cent of the shaft cross-section. The dynamic effects of a moving conveyance are also analyzed.

Jan 1, 1988

By R. S. Olson

The operation of a series wash thickener-two stage filtration circuit determines the soluble loss in many hydrometallurgical operations A study of this circuit yielded expressions which permit calculation of soluble loss for almost any condition of operation. The soluble loss over a range of the circuit variables is presented to illustrate and evaluate circuit performance, The interrelation of factors affecting filter performance and some of the wash circuit, variables are quantatively described. Filter wash, which is governed by wash zone size, filter pulp level and filter feed pulp density, has the greatest affect on soluble loss. Excepting clothing blinding and flocculation the factors which decrease filter capacity also decrease soluble loss. Repulping with water, under some circumstances, can bean important means of soluble loss reduction. Water for primary filter wash, leach pulp density repulp density and wash thickener underflow density have little effect on soluble loss. The dilution of both o the filter pulps with wash solutions is suggested as a means of reducing soluble loss, and at the same, time, controlling the performance of the filters. Blowback and filter cloth blinding seriously increase soluble loss.

Jan 1, 1962

By W. R. Bull

This paper examines water-only cyclone performance for the cleaning of fine coal, and the effects of changes in feed flow rate, feed pulp density, and vortex finder diameter. A model is presented for performance simulation which can be used to predict products obtained based on feed washability data.

Jan 1, 1987

By S. K. Kawatra

The use of inferential particle sizing for a closed wet grinding circuit control has been practiced for several years. This paper presents a review of some inferential sizing equations developed for pilot and industrial plants using regression analysis. An analytical development is then presented showing how the general inferential sizing model arises from the nature of the classifier model. The relation between the general sizing model and the individual equations is then discussed.

Jan 1, 1982

By Leland L. Mink

Open-pit mining is sometimes conducted in areas where the artesian pressures contained in aquifers underlying the pit's floor are great enough to cause floor heave. In order to reduce this pressure several methods are commonly used. One of these methods is a pressure relief well or depressurization wick. The wick consists of a borehole which is filled with gravel and cased at the surface. The wick is allowed to flow freely, thus reducing pressure near its location. The spacing and depth of these wicks can be determined by a simple analytical and graphical technique which considers the weight of material overlying the aquifer and the artesian force within the aquifer. An example of the technique using data from a Colombian coal mine is presented.

Jan 1, 1986

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints.

Jan 1, 2002

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints ? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints. When complaints come, standard practice is to set up a seismograph in the neighbor’s yard to monitor the blast. Immediately after the blast, the neighbor usually reappears from the house wanting to know the seismograph reading. When told that the PPV was 0.1 in/set, well below damage levels, the homeowner explodes saying “Your machine is wrong”. Perhaps he is right. Understanding why people complain about blasting is not about PPV, it’s all about structural response. People could care less about how much the ground vibrates; they only care about how much their house vibrates. In this paper we will examine the primary factors that control structural response. Through the use of a large array of digital seismographs, the effects of two production blasts on a community surrounding a quarry are studied. The predicted structural response resulting from each blast is calculated at 175 seismograph locations. The predicted response is then correlated to previous research on human perceptibility to vibrations. The results of this analysis and correlation give a better understanding of what the residents actually feel in their homes. The detonations of two single-hole signature blasts are also recorded by the array of seismographs revealing the dynamic characteristics of the geology ‘surrounding the quarry. Once the influence of the geology was understood, blasts were configured to disrupt the natural rhythm of the site through the use of millisecond delays.

Jan 1, 2000

By James M. Kramer

This paper introduces an analytical approach for the determination of the vertical stress in the chain pillar system between two adjacent longwall panels. The development of this approach is based on the principles of fracture mechanics and superposition. Some empirical formulae have also been incorpomted into the development of the mathematical model. The mine entries and longwall gobs are treated as Mode I cracks in an infinite plate while the resistance of gob material and the characteristics of the pillar yield zone are considered as the distributed forces on the surface of the cracks. An user- friendly computer program has been developed to facilitate the calculation involved in this task. This approach is as accurate as the numerical analysis methods but requires much less expertise and computer hardware and software to apply

Jan 1, 1998