Search Documents

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By J. M. Hodge, M. A. Orehoski

THE relationship between hardenability based on a 50 per cent martensite criterion, and that based on higher percentages of martensite in a number of low-alloy steels was discussed in a previous paper by the authors.1 It was found that the differences between the hardenability values based on the 50 per cent martensite and full martensite criterions increased as the hardenability increased and that, in the steels of higher hardenability, these differences were fairly large. Furthermore, it was found that these relationships could be expressed with reasonable accuracy as a function of the hardenability. The importance of the full martensite criterion of hardenability in relation to the attainment of the optimum mechanical properties of tempered martensite was emphasized in the earlier paper. The purpose of the present work is to study the effects of some of the individual alloying elements on hardenability, using three different percentages of martensite as criteria, and thereby to evaluate the role of these individual elements in the general hardenability relationships previously reported. EXPERIMENTAL PROCEDURE Induction-furnace heats weighing 17-lb., of the compositions given in Table I, were cast and forged into 1 ¼ in. round bars. All heats were killed with aluminum additions corresponding to 1 lb. per ton. The compositions were chosen to represent several series of steels, in which only one alloying element would vary and in which the nonmartensitic constituents on quenching would be predominantly bainitic. All bars were normalized from 1650°F. and tempered one hour at I 150°F. prior to the hardenability determinations. Hardenability values are based on metallographic examination of standard Jominy bars, quenched from 1600°F. (I hr. and 20 min. heating time). The general procedure was the same as outlined in detail in the previous paper; (I) that is, the distance from the quenched end of the bar to the point of 0.1 per cent transformation was first measured on the microscope and then the percentage of martensite was estimated at every 0.05 in. from the quenched end, and these percentage values plotted against the distance along the bar. In this case, samples 2 in. long were cut from the quenched end of the Jominy bars and 10 fields were examined and averaged at each distance. The conversion of Jominy distance to ideal diameter is based on a revised correlation curve (Fig. I). This curve is based on work carried out at the Research Department of the South Chicago Works, Carnegie-Illinois Steel Corporation, and represents a direct correlation between hardenability values as deter-

Jan 1, 1946

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

By E. Houdremont

THE different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any sys-tematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classifica-tion proposed nevertheless also suggests relationships among the proper-ties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition correspond-ing to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of tran-formations. Steels. of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject

Jan 1, 1934

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled' condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O'Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator's judgment of the correct 'colour'. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

By M. R. Pickus, I. W. Pickus

ORDINARILY age-hardening is thought of as being associated with a limited solubility of one metal in another. Much less has been written about the type of age-hardening that attends the formation of superstructures. Solid solutions generally have a disordered or random arrangement of atoms; that is to say, in a unit cell, such as that of the face-centered cubic lattice, there is no distinction between atomic sites. Atoms of a given metal may occupy cube corners or face centers. Under certain conditions, however, some alloys develop what is known as an ordered structure. In this case, cube corners would be occupied by only one type of atom and face centers by another type, Associated with this ordering process are many interesting changes in physical and electrical properties. Moreover, in many instances the alloys become susceptible to age-hardening. From the evidence now to be described, it appears that age-hardening in 14-carat gold alloys is due to the formation of both a super-structure and a precipitate. Alloys of the metals gold, silver and copper were known in antiquity. The available knowledge regarding their constitution has been ably summarized and extended by Sterner-Rainer,1 Janecke,2 Carter,3 Wise,4 and Coleman.5 Despite the long familiarity with these alloys and the numerous investigations of their properties that have been made, there is still much that remains unexplained. It has been known for a long time that the hardness of these alloys is closely related to the rate of cooling, Similar changes have been observed in the binary gold-copper system,6 one alloy of which corresponding to the formula Cu3Au, has been the subject of a careful and competent report by the English investigators, Sykes and Evans.7 They have established the fact that the shift of atoms from the ordered to the disordered condition takes place in some critical temperature range. At temperatures above the critical range the structure is random, and at temperatures below it the structure is ordered. No difference between these two structures is revealed by the microscope. Both have a face-centered cubic lattice and complete solubility, so that there is no evidence to suggest that the changes in properties are associated with a phase change, The more slowly the alloy is cooled, the higher is the degree to which the ordering process proceeds and the more marked is the increase in hardness. As experimental data were accumulated on 14-carat gold alloys, several contradictions arose. Certain observations tended to confirm the existence of a superstructure, while other observations seemed to be inconsistent with such a transformation. PRESENT INVESTIGATION As a focal point about which to develop this subject, it is expedient to consider first

Jan 1, 1943

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By Bob Miller

"All industries have parts and equipment that are exposed to some type of destructive wear. Hardfacing is a cost-effective tool that will minimize wear and increase service life. At first glance, hardfacing can be confusing and troublesome. In reality, it is not.Postle Industries, a manufacturer of hardfacing products, has found that the 22 answers to frequently asked questions may help operators select hardfacing products that are most appropriate for their application. The first 10 questions are addressed in these pages, the full list can seen at Mining Engineering online under the Web-Only Content section.1. What is hardfacing?Metal parts often fail their intended use not because they fracture, but because they wear by abrasion, impact, metal-to-metal contact or some other form of wear, which causes the parts to lose dimension and functionality. Hardfacing, also known as hard surfacing, is the application of a buildup or wear-resistant weld metal onto a part’s surface by means of welding to extend the life of the part. The weld metal may be applied as a solid surface or in a pattern, such as a waffle pattern, herringbone or dot pattern, etc.Hardfacing is becoming increasingly important for many industries to protect equipment that is exposed to wear and abrasion including parts used in mining, earthmoving and construction, oil and gas drilling and steel making and forging. Extending the life of wear parts can save thousands of dollars and improve productivity. Hardfacing can be used to recondition parts that have already been exposed to wear and have lost their useful life, or used in the manufacture of new parts to improve their life before they are put into service.There are three main types of hardfacing applications:• Build-up or rebuilding.• Hardfacing or overlay.• A combination of build-up and overlay.2. What base metals can be hardfaced?Carbon and low-alloy steels with carbon contents of less than 1 percent can be hardfaced. Medium carbon and low-alloy steels are very common since they provide higher strength than mild steels and better abrasion resistance. High carbon alloys may require a special buffer layer.The following base metals can be hardfaced:• Stainless steels.• Manganese steels.• Carbon and alloy steels.• Cast irons.• Nickel-base alloys.• Copper-base alloys."

Aug 1, 2016

By W. H. Mathews

"The Hardie group of cinnabar claims is in the interior of British Columbia; 25 miles northwest of the city of Kamloops. It is one of a number of mercury; properties scattered along a north trending belt 20 miles long and up to 5; miles wide. In all but one of these properties cinnabar is associated with; dolomite veinlets in zones of carbonate alteration in bedded rocks of Triassic; and Cretaceous (?) age; or in intrusives cutting these bedded rocks. No dolomite alteration or cinnabar mineralization is known in the undoubted Tertiary rocks adjacent to the mercury belt.The mercury showings of the Hardie group lie for the most part in a granitic stock cutting Cretaceous (?) volcanics. The rock in this intrusive shows marked variations in texture and has been described in earlier reports as granite and granodiorice, granite porphyry, and trachyte or dacite porphyry. At Hardie mountain the cinnabar mineralization, unlike that of the other properties, is associated with a fine-grained, almost chalcedoni c, quartz; carbonates, though present, are of minor importance. Some of the most interesting showings are found in an adit in the southeastern part of the property where cinnabar mineralization shows a very distinct structural but not a genetic relationship to a brown porphyry dyke 2 to 8 feet wide cutting a phase of the stock that may best be described as aplitic"

Jan 1, 1954

By Arthur Taggart

THE following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.1 Screen apertures used are the average apertures of testing screens of the meshes given. Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill. Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversize reground-in pebble mill, see Card 113. Feed to mill through 2-in. mesh.

Jan 7, 1915

By Robert Franke

(Butte Meeting, August, 1915.) IN view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the imme diately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in.

Jan 7, 1913

By J. H. Frye, R. M. Treco, J. W. Caum

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."1 It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data 2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. HARDNESS, LATTICE PARAMETER AND IONIC OVERLAP Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2, It is believed that most of the values are accurate within the limits indicated by the rectangles, These data are also presented in Table I. Ultimate Meyer hardness, Pu, is defined by the equation: [P" - D2] where L = load, D = diameter of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro¬duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. [ ] The question arises as to whether or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By Leonardo Flores

"Minera Escondida operates two open pits on a porphyry copper district, southeast of Antofagasta, Chile. During 2005, ore will be delivered exclusively from one pit to two concentrators, while from 2006 both pits will provide ore to these plants. Annual testing programmes on drillhole samples, have allowed for the construction of hardness block models since 2000. These models have delivered two main hardness descriptors, the Bond work index and the SAG power index. These parameters and plant operational specifications have been used as input information to forecast, the expected throughput and ball mill product size (P80) for each block of ore. Two forecasting techniques have been used, an in house model, strongly dependant of bond work index and MinnovEx´s CEET2, dependant of Bond work index and Sag power index and other parameters. Model performance has been evaluated from reconciliating on a monthly basis, the forecasted throughputs against a recalculated plant throughput which accounts for losses in tonnage not caused by ore hardness but instead by unscheduled plant operation problems. The model performance for 2003 was ± 2% yearly and ± 5% quarterly, well within the expected ± 3% and ± 10%. INTRODUCTIONThe Escondida porphyry copper district is located 140 km SE of Antofagasta, Chile at 3150 m.a.s.l, at 24°16’ South latitude and 69°04’ West longitude (figure 1)."

Jan 1, 2005

By Samuel Hoyt

THE hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer's analysis were employed. MEYER'S ANALYSIS OF BALL INDENTATION TEST The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer's analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work maybe obtained from elsewhere.1 As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows.

Jan 2, 1926

By K. Thuro, S. Schneider, H. Kasling, P. Ellecosta

"One of the most important methods for material testing is the characterization of the hardness, which is defined as the resistance of a material to the penetration of another one. The methods according to Brinell, Vickers, Rockwell and Knoop are today the most common and standardized tests for metal. As they are developed for predominantly ductile materials like steel, they can’t easily be applied to rocks which react much more brittle under indentation. But just as steel, rock is composed of different minerals and has a specific microstructure. Its mechanical parameters are connected with the particular grains, their cohesion and interlocking, just like steel.The abrasivity of rocks and the accompanied wear of drilling tools today are mainly determined by simple and fast laboratory tests such as the Cerchar abrasivity test or the rubber wheel test. Such laboratory tests are good tribological tests, but there are limits. The Cerchar abrasivity test for example has weaknesses in extreme cases, that mean soft or very hard rock types. This leads to an underestimation of abrasivity, e.g. in poorly lithified sandstones or very hard, fine grained and extremely abrasive rocks. As mentioned, hardness characterizes, depending on the type of deformation, predominantly plastic (metal) or elastic properties (rubber). Rocks are in the range between these two extremes. Since the rock drilling process can be seen as a kind of penetration process on macroscopic and microscopic scales, we picked up the idea to characterize the interaction of rock materials and TBM-disc-cutters with hardness tests. In addition, this supports for a better understanding of the wear process on disc cutters. We used the hardnessdisparity concept after Cardu & Giraudi (2012) because wear can be understood as the interaction between the wear part and the material which causes the wear (tribological system). Several rock-forming minerals and some fine to coarse-grained monomineralic and polymineralic rocks were tested. In contrast to Cardu & Giraudi, we used in the first step of investigations the method after Vickers with loads up to 294.2 N (HV 30), depending on the estimated hardness to get bigger indentations and therefore as well information about the cohesion and interlocking of the minerals/grains. We also tested several associated disc cutters. First results show that with higher loads (HV 5 - 30) and at least 15 indentations, we get a structural hardness in fine-grained rock samples, which allows a good characterization of the elasticity and brittleness. Nevertheless, for the coarse-grained rock samples we need up to 40 indentations for a good characterization. Using this method, a prediction of disc cutter wear is feasible taking into account the hardness of the disc cutter steel. In this paper, we would like to present this approved method in material sciences to derive an additional parameter for the characterization of rock abrasivity and wear."

Jan 1, 2015

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949

By F. P. Agterberg, A. G. Fabbri

"A statistical analysis was done on the locations of 718 copper and 1 257 gold deposits in Abitibi. This area of about 20 000 square miles is one of the better-explored metal-producing areas of Canada.Patterns of clusters were studied by harmonic analysis. Several two-dimensional power spectra showed a number of distinct peaks. Sets of crest lines for patterns of interfering waves were constructed on the basis of these peaks. They pass through elongated clusters of deposits which are spaced more or less equally. For copper these periodic regularities in location may coincide with geological structures largely of Archean age (major fractures and sedimentary belts indicating synclinal structures). A directional relationship with swarms of diabase dykes of known ages and distinct attitudes indicates that the gold mineralization is, in part, younger than the copper mineralization."

Jan 1, 2014

By Frederick B. Kuhnow

Harmonic energetic delamination a building is being considered for demolition at a formerly known atomic power lab. The building is within a containment structure under a negative pressure, so that no radioactive material is leaked out to the environment. A new approach was developed to make this work possible.

Feb 1, 2020

By Trevor L. L. Orr

"AbstractThe background to the harmonization of geotechnical standards that has taken place in recent years in Europe has been the move to more economic and political integration following World War II that has led to the formation of the European Union. Prior to 2010 the standards used in the European countries for geotechnical design, investigation and testing and for the carrying out geotechnical work, such as the installation of piles, were the different national standards, which were not harmonized. The harmonization of geotechnical standards in Europe started in 1981 with work on a model Eurocode 7 for geotechnical design that led eventually to publication by CEN, the European Committee for Standardization, of the European Standard version of Eurocode 7 in 2004. In parallel with the work on Eurocode 7, a large number of associated harmonized standards have been, and are being, prepared by CEN and by the International Standards Organization (ISO) for geotechnical investigation and testing and for the execution of geotechnical works. Standards published by CEN must be adopted by the CEN member countries and all conflicting standards withdrawn. Hence all the CEN countries have adopted the same the harmonized text of Eurocode 7, but with National Annexes that allow national choice with regard to Design Approach and partial factor values. The adoption of Eurocode 7 and its associated geotechnical standards has removed the barriers to geotechnical activity in Europe due to the presence of different national standards. It has also enhanced the ability of EU firms to compete in the global market.Background to harmonization of geotechnical standards in EuropeThe initial moves towards the harmonization of geotechnical standards in Europe can be related to the economic and political developments that took place in the period immediately following World War II to revive the economies of Western Europe. Europe at that time was divided by a political and, in many places, a physical barrier, known as the Iron Curtain, into two very different and separate zones: communist in the east and non-communist in the west. In 1952 the European Coal and Steel Community (ECSC) was formed, linking 6 countries: Belgium, West Germany, France, Italy, Luxembourg and the Netherlands, and establishing a common market in coal and steel. The ECSC was the first international organization to be established on the basis of supranational principles whereby negotiated power is delegated to an authority by the governments of the member states. In 1957 the ECSC became the European Economic Community (EEC), also known as the Common Market in the English-speaking world, with the aim to bring about economic integration. With the addition of Denmark, Ireland and the UK in 1973 and Greece in 1981, followed by Portugal and Spain in 1986, this led to the formation of the European Union (EU) in 1993. East and West Germany were reunified in 1990, following the fall of the Iron Curtain in 1989. In 1995, Austria, Finland and Sweden joined the EU, and since then the numbers of countries in the EU has increased to 28, many of which are countries that were formerly behind the Iron Curtain."

Jan 1, 2014