Search Documents

By AIME AIME

It is with the deepest personal sorrow, and with the regrets of the Steel Company of Canada, that I report to you the death of one of our most valued associates, the late Frank B. McKune, superintendent of the Open-Hearth Department of our company. Many of you will remember Mr. McKune for his long attendance at these meetings, for the intelligent interest he took ill them, as well as for his innovations in steel-production practices.

Jan 1, 1940

By Ali Azizian, Brian Hall

"Driven piles were selected to support the Fraser Heights Bridge bents. Piles were a key component of the top-down construction approach, which was adopted for minimizing potential impacts on an environmentally sensitive wetland. Project requirements mandated verification of pile capacities using dynamic methods. More than 40 Pile Driving Analyzer (PDA) tests were performed. The subsurface conditions were highly variable. On the east side, piles extended through loose sands, soft silts/clays, and two peat layers and were founded in glacial till-like soils at about 45 m depth. However, on the west side, till-like materials were so shallow that it was difficult to drive the piles sufficiently deep to obtain the necessary lateral support. This paper provides an overview of the geotechnical considerations of the bridge design and top-down construction approach, and expands on the presentation of PDA results and how they compared to pile capacity estimation methods and parameters recommended in the applicable design codes.INTRODUCTIONThe Fraser Heights Bridge (FHB) was a component of the Fraser Heights Connector (FHC), a 2 km section of the South Fraser Perimeter Road (SFPR), constructed as part of the Port Mann/Highway 1 (PMH1) Improvement Project. The FHC is located in northeast Surrey BC (Fig. 1).Two major design and construction determinants were: 1) a mandated tight schedule to provide a non-tolled alternative to a new toll bridge; and, 2) an obligation that construction had to occur with minimal impact on the environmentally sensitive wetland the FHB crossed, including limiting the footprint of the permanent and temporary works to less than 45 m2, and prohibiting construction access onto the wetland. Construction equipment was only allowed on the wetland on temporary trestles or on the finished structure. This latter requirement resulted in the bridge being constructed span by span, using a top-down approach."

Jan 1, 2016

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"Direct digital manufacturing offers promise as a technique for fabricating complex hydrogen purification membrane support structures. Free form fabrication methods can produce parts with complex structures, and sintering parameters can be controlled to adjust the density, pore structure, pore pathways and strength in catalytic substrate constructs. Efforts are underway to define the influence of selected process variables on the chemical and mechanical properties.IntroductionThe Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production. Because hydrogen readily passes through palladium, a structurally sound palladium-based membrane is capable of separating relatively pure hydrogen from other gases. In order for this technology to succeed, a suitable substrate material must be identified.High purity hydrogen is produced by various means. A common method involves a two-stage process for separating hydrogen from a hydrocarbon gas stream: 1) hydrogen-rich syngas is produced by the catalytic reaction of natural gas or another light hydrocarbon gas with steam, and 2) hydrogen is separated from the other syngas components by pressure swing adsorption (PSA) (US. Energy Information Agency, 2011). In PSA, gases enter a column that is packed with a material that absorbs gases as the chamber is filled and pressurized. As the pressure is slowly relieved, the absorbent material releases hydrogen at a higher pressure than the impurity gases. PSA processes produce 99.99% pure hydrogen at a high recovery rate. These systems typically demand a high capital investment due to the high pressure and multiple stages (columns) needed to attain high hydrogen production rates.Research geared toward reducing hydrogen production cost is focused on the development of improved catalysts and adsorbent materials as well as more effective single-stage separation processes. An interesting method combines hydrogen reduction catalysis and filtration. Nascent hydrogen is separated from other gases as it selectively permeates the filter. Catalyst filters may be made of gold, silver, platinum, palladium or precious metal alloys (Davis, 2009)."

Jan 1, 2012

By W. Kotze

The gold mining industry has mainly relied upon the use of highly polluting chemicals, such as mercury and cyanide to recover gold from its ores. The Coal Gold Agglomeration (CGA) process was developed some years ago and has the advantage in that gold is recovered by a procedure which has little or no negative impact on the environment. A gold ore containing liberated gold particles is contacted with coal-oil agglomerates, where by the gold is recovered into the coal/oil phase. Laboratory scale batch tests were performed on an artificial mixture gold slurry and gold recoveries of up to 85% were found under optimized conditions. By recycling the coal/oil phase, it was found that the gold loading onto the agglomerates was increased. Tests performed on an industrial ore yielded slightly lower gold recoveries, and X-ray Diffraction (XRD) analysis on the coal/oil phase showed that minerals other than gold was recovered into this phase. A comparative study was conducted whereby the CGA process was compared to mercury amalgamation. Gold recoveries obtained through amalgamation were 15% lower than by the agglomeration process, which indicates that this process can be considered favourably as an alternative to amalgamation.

Jan 1, 2000

By J. Etay, S. Daugan, Y. Fautrelle

"New type of electromagnetic parametric instabilities arising at the free surface of liquid metal in the presence of a low frequency magnetic field are presented. First, the mechanism of the instability is analysed in an idealised case. Then, the experimental device working with mercury is described. Various shapes, both regular and irregular, of free surface are found. A experimental stability diagram is obtained. Measurements of the deformation performed on photographs are compared with physical orders of magnitude.IntroductionWhen a liquid metal pool of electroconductivity a is submitted to an A.C. magnetic field B = B0 cos mt, electrical currents j are induced in the liquid metal and interact with the applied magnetic field to create electromagnetic body forces F = j x B. Those Lorentz forces comprise both a mean value (time average) and an oscillating part. Those forces are widely used in many metallurgical processes to stirr a liquid metal or to control its free surface, e. g., in aluminium continuous casting or electromagnetic levitation problems (1-3). When liquid metal free surfaces are submitted to AC. magnetic fields, the shape of those interfaces may interact with the applied field and leads to a various instabilities. A review of these instabilities may be found in Fautrelle (4). That instabilities may be a problem for the control of processing as electromagnetic levitation or quasi-levitation."

Jan 1, 1999

By H. C. Morehead

The United States Cement, along with other industries, is being devastated by an unprecedented penetration of domestic markets by imported products. The overriding questions are: 1. Have foreign manufacturers improved their processes to an extent they can outperform U.S. producers in their home markets? 2. Is it gross inefficiency on the part of the U.S. producers that is allowing foreign producers to be capable of replacing a local U.S. producer in his normal home market? 3. Is there a combination of the first two questions that economically justifies this type of market overrun? The answer is a simple NO!. In a fair trade market atmosphere, U.S. producers are definitely competitive.

Jan 1, 1985

By Wayne E. Glenn

A centennial meeting should be a time to take stock, to evaluate performance, to plan ahead. It is like a line in a televised commercial that goes, "You've come a long way to get where you've got to today." And no less should be said of the mining and energy industries. We have come a long way. A hundred years ago when AIME was founded, this country produced 23 million tons of bituminous coal and 5.2 million bbl of oil. The figures in 1970 were about 580 million tons of coal and 4.1 billion bbl of oil. In spite of such accomplishments, serious and compelling voices are heard in the land - doubting sincerity, questioning corporate structures, and challenging ethics. Those doubts are raised in one part of Washington at the same time that other sections of the Capitol are asking us to produce more energy in order to keep up with population growth, emerging nations, and new technologies. Those of us in the fuel or energy business frequently talk about the race for energy. The question is, can we develop enough energy fast enough to outdistance our present and increasing demands? Recently I heard of an incident that - in an odd way - caused me to think of the energy race. The incident involved a sky-diver who jumped from an airplane without a parachute. He was handed a chute in mid-air by a sky-diving companion. He put it on, opened it, and landed safely. In a way, it seems to me that our society is hurtling through space and that it needs some help from the energy industries to land safely. We're doing our best, but under some rather difficult conditions. Because of illegal strikes and work stoppages the coal parachute is snarled a bit. The cut in percentage depletion and other tax changes have put some holes in the oil parachute. And the gas ´'chute has been in trouble for some time because of unrealistic controls on producer prices. The irony of the situation is that some of the very people who have been taking potshots at the energy parachutes for a long time are the ones who are complaining loudest now because the 'chutes are not functioning the way they could. The safety of the entire nation can depend on the energy industries.

Jan 1, 1971

By Charles L. Elliot

Data on mining applications of geophysical activity in the Free World in 1964 have been made available to SME again this year by the Society of Exploration Geophysicists. Worldwide data were collected as part of an annual service to the mining industry by the Committee for Geophysical Activity of SEG. Data are taken from 245 voluntary responses (53%) to questionnaires circulated to 463 company, government and university organizations engaged in mining geophysical operations and research all over the world. WORLD ACTIVITY Worldwide manpower utilization totalled 9323 professional man-months and $14.5 million was reported spent in mining geophysical activity in 1964. This is up from 9078 man-months and $12.6 million in 1963 and 8065 man-months and $12.8 million in 1962. Worldwide geophysical activity in terms of manpower utilization and expenditures is presented in the accompanying table.

Jan 9, 1965

By Richard Harrison, Frank Lim

Deepsea Mining will soon become a reality with Nautilus Minerals getting their equipment ready to mine SMS at Solwara 1 off the coast of Papua New Guinea. The vertical transport system (VTS) adopted by Nautilus consists of a riser hanging ‘freely’ from the mining production vessel with a lifting pump unit suspended at its lower end. A compliant jumper connects the pump to the seabed crawler without restraining its movements. In this free-hanging VTS arrangement, the vessel can be re-positioned to follow the crawler should it want to extend the mining area and start stretching the jumper. A recently proposed alternative to this is a free-standing VTS whereby the riser is grounded on the seabed with a base and maintained in an upright position by distributed buoyancy modules or a buoyancy tank at the top. A compliant jumper connects the seabed crawler to the riser base, and another connects the riser top to the vessel. In this free-standing arrangement, the entire VTS can be lifted clear of the seabed for relocation to a new mining area. This paper will describe the important features of the two options and discuss the advantages and disadvantages in respect of riser dynamic behavior, water depth, weather and mining windows, pump maintenance, installation and retrieval, continency measures, etc. The two systems will also be appraised separately for mining SMS and SMnN deposits.

Jan 1, 2018

By Sup Hong

"Lifting riser in deep-seabed mining (DSM) is exposed to acute and chronic stresses of materials, whose yield will result in the most critical loss of total mining system. For freehanging riser (FHR), the axial vibration and local bending of riser may produce acute stresses, in the meanwhile, vortex-induced vibration (VIV) in relative current, friction and collisions of solid particles with inner-wall, and material corrosion in seawater are representative causes of chronic stresses. The chronical stresses bring about fatigue failure or abrupt failure by material loss. Hydraulic lifting is effective and promising for transportation of minerals, however, ecofriendly treatment of operating seawater is an unease hurdle to come over. Sizing of riser section confronts multi-directional problems, i.e. safety of slurry transportation (flow assurance), material safety of riser (wall thickness), seawater treatment on board, etc.A free-standing riser (FSR) might exclude a part of design problems of free-hanging riser and give a way to sustainable mining. FSR stands vertically by means of sub-buoyancy part(s). The top of FSR emerges above sea surface and is connected with mining platform through jumper line (supported by external yoke). Total amount of sub-buoyancy and location(s) have to be carefully determined in viewpoints of dynamics of FSI (fluidstructure interaction) in waves and currents. The concept of FSR gives more freedom for design of multi-functional riser system in view of sustainability of DSM. In DSM, sustainability concept may be focused on eco-friendly treatment of seawater and sediment, and safety of total mining system. For feasibility of FSR, however, installation, maintenance and repair need to be investigated thoroughly in collaboration with industry experts"

Jan 1, 2017

By T Casten

Freeport IndonesiaÆs DOZ (Deep Ore Zone) mine is scheduled to commence production in the second half of 2000. The DOZ will produce 25 000 tpd using mechanised block cave mining methods and will have a number of major improvements when compared to previous block cave mines in the district. The DOZ will have an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system than in previous underground mines in the district. This paper will describe the mine plan, haulage, and ventilation systems, and compare them to those used in other operations in the district.

Jan 1, 2000

By Bradford C. Wesstrom, Ricardo Parra

The Freeport McMoRan El Paso Refinery uses co-generation to produce some of its electricity and all of its steam. This paper will cover the operation of the co-generation plant natural gas turbine at a fixed RPM for blade longevity and energy output. The by-product heat from the turbine passes through boilers with additional heat from a duct burner to produce steam for the Tank House and auxiliary operations. The steam demand varies dramatically throughout the day based on unloading activities in the Tank House. The use of an automated steam control system within the El Paso Refinery will help stabilize line pressure by incrementally controlling steam consumption based on electrolyte temperature. This will minimize steam line pressure fluctuations. INTRODUCTION In the mid 1920’s the Nichols Copper Company of Laurel Hill, New York recognized the need for a modern copper refining facility in the southwest. Due to the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the logical location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Energy costs (electrical and thermal) are critically important in the viability of modern copper electrorefineries. The El Paso Refinery produces electricity and steam through its cogeneration system. The El Paso cogeneration facility is a natural gas, 15-megawatt facility containing five turbine generators and associated waste heat recovery boilers. The facility is divided into two phases. Phase I consists of two Allison 2.2-megawatt turbine generators. Phase II consists of three Solar Taurus 3.5-megawatt turbine generators. Presently three units in Phase II are operated. The Phase I units were purchased and installed in 1986 and the Phase II units in 1992 (Solar 1991). The facility operated at full capacity until 2003 when steam demand was significantly reduced due to decrease in cathode production and closure of the copper sulfate and precious metal operations. Phase I units were taken out of service and put on care and maintenance status.

Jan 1, 2019

By Napitupulu P

PT Freeport Indonesia currently operates a concentrating complex capable of milling 127 000 metric tonnes per day of copper and gold hearing ore. The facilities consist of both a conventional crushing, ball mill and flotation circuit and a SAG, ball mi

Jan 1, 1997

Equipment-washing facilities at Freeport-McMo-Ran?s Sierrita Mine in Arizona produce a mixture of oil and water that was difficult to dispose of easily or cheaply. However, after some changes in the facility, waste oil is now used as part of the mining process. Freeport-McMoRan Copper & Gold Inc., head-quartered in Phoenix, AZ, operates copper, gold and molybdenum mines. It is the world?s largest producer of molybdenum. Heavy equipment used at the mine is hosed off periodically in the wash bay. The dirty water and oil mixture drains into the sump next to the bay. Oil was manually collected for disposal. This was a tedious and dirty process Mine managers sought a more efficient method of removing the oil. Instead of spending the time and effort skimming the tank with vacuums or sorbents, they enlisted the help of Abanaki Corp., manufacturer of the Model 4 Oil Grabber. Engineers designed the sump to utilize prevailing winds to blow the oil to one corner. This was the ideal place for the Abanaki skimmer. The skimmer removes the oil and discharges it into a plastic storage container. ?This reduces the time needed to keep the area clean, and the staff can focus on cleaning the equipment rather than worrying about the oil,? according to Jay Salerno, construction manager at the Sierrita Mine. Salerno is considering adding an optional oil concentrator to the skimmer to make the process even more efficient. The concentrator would remove any water picked up by the belt and return it to the sump, leaving nearly pure oil for disposal. Because the mine is located in the Sonoran desert, most of the water evaporates in the hot, dry air and is not reused.

Jan 1, 2009

By K. H. Nimerick

A unique freeze conditioning agent (FCA) which functions by forming structurally weak ice rather than suppressing the freezing point of water has been successful in alleviating frozen coal problems. Frozen coal treated with FCA has been quickly unloaded at temperatures below -17.SoC (O°F). Other areas where FCA has found utility has been de-icing conveyor belts, idler, idler arms and other moving parts that have been impeded by ice.

Jan 1, 1977

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

By J. S. Coats, G. E. Patts, N. Hughes

Conventional sampling methods are known to suffer from the variable loss of fine gold by elutriation. Freeze sampling yields representative and quantitative data that, when combined with information on the sedimentology of gravel-bed rivers, may facilitate the development of improved dispersion models for source detection. It is suggested that freeze sampling may have particular application to the orientation stage of a large gold exploration survey

Jan 1, 1991

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013