Search Documents

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2017

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2018

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

Researchers examined datasets from two separate studies that measured common demographic variables but different safety performance outcome variables. Of specific interest was how types of experience might relate to workers’ preparedness to effectively mitigate or respond to both routine and nonroutine risk in the mining industry. The results suggest that individual factors such as length of job, industry, and mine experience are predictive of routine safety performance — as measured by self-reported proactive and compliant safety behaviors — and/or nonroutine safety performance — as measured by perceived competence in self-escape knowledge, skills and abilities (KSAs) — in significant and sometimes unexpected ways.

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012

By W. H. Moore

It seems necessary, at times, that we should reconsider some of the more obscure causes that lead to explosions of gas and coal-dust in mines, in the hope that a recapitulation will keep before us that old and true saying "eternal vigilance is the price of safety". This explosion, while not extensive (resulting in only two much to be regretted deaths) enlarged our vision as to the possibility and probability of other explosions with more disastrous results. As this is only a partial report I shall have to omit many things that are generally included in describing a mine explosion. The mine was worked exclusively with electric cap-lamps -only firebosses and other officials carried safety-lamps. All shots were examined and fired by firebosses with a small hand-battery. Monobel was used exclusively for blasting, and clay for tamping. The system of haulage iri use was main-rope and winches, horses being employed for gathering. Compressed-air was the motive power for all winches and pumps, excepting the pumps at the shaft-bottom which were steam-driven. The mine was wet with practically no dust anywhere, except what was being made at the coal-face in the getting of the coal. Gas was found occasionally, generally in the brushing, especially where the brushing was carried up to a small seam, 2 to 6 feet above the main seam. The place where the explosion took place was known as Leigh's heading, which was being driven to the rise, immediately inbye of the siding (off No. 1 left, off the new slope) and was about 90 feet up from the level.

Jan 1, 1926

By J. E. Urosek, K. L. Cashdollar, D. A. Beiter, G. J. Shemon

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on mine ventilation stoppings at the NIOSH Lake Lynn Experimental Mine (LLEM). After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to mitigate or eliminate future occurrences. As part of these post-explosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, are documented as evidence of the strength and the direction of the explosion forces. The LLEM data showed that a total pressure of 52 kPa (7.6 psi) destroyed the solid concrete block stopping, ~36 kPa (~5.2 psi) destroyed the hollow-core concrete block stopping, and 9 kPa (1.3 psi) destroyed the steel panel stopping. These results will assist investigators in determining the explosion forces that destroy or damage stoppings during actual coal mine explosions.

By Roberto Folcht

The obligations of the European Directive 96/82/EC on the control of major accident hazards, the so-called Seveso II Directive, became mandatory within the E u ropean Member States February 3, 1999. Explosive products have been included within the Seveso II Directive, in the categories of substances capable of generating a major accident. In addition to taking “all measures necessary to prevent major accidents,” explosive manufacturers are also obliged “to limit their consequences for man and the environment.” However, for explosives in particular, no pro c e d u res, nor specific re f e rence values for damage calculation, are given either in the Directive or in the corresponding Italian Legislation, “Ministry of the Environment decree of 20 Oct. 1998.” This article presents a simplified but scientifically rigorous approach for the first approximation calculation of the effects on the surrounding area following an accidental explosion. As an example of the method of calculation, the damage areas in a hypothetical explosives manufacturing facility, as shown in F i g u re 1, will be anal y z e d . The method proposed in this article can also be used for the analysis of explosions of gas in tanks or pipelines,

Jan 1, 2004

By B Mohanty

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2014

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2011

By Michael J. Sapko, Kenneth L. Cashdollar

In This Chapter [Methane ignition as initiation source for much larger secondary coal dust explosions Rock dusting requirements to prevent coal dust explosions Dangers of hybrid mixtures of methane and coal dust] Although methane explosions are dangerous, those that involve coal dust are even more so. If exploding methane disperses and ignites the coal dust that has accumulated on the mine ribs and floor, the burning coal dust immeasurably increases the strength of the explosion. Such methane-dust explosions are prevented by inerting the coal dust in a way that prevents the exploding methane from igniting it. This chapter discusses the dust hazard and how it is pre-vented in U.S. coal mines. METHANE IGNITION AS INITIATION SOURCE FOR MUCH LARGER SECONDARY COAL DUST EXPLOSIONS The typical scenario for coal mine explosions starts with the ignition of a flammable methane-air atmosphere near the face. The turbulent winds from the primary methane explosion then disperse the coal dust. If there is insufficient rock dust (usually limestone), a secondary coal dust explosion then propagates throughout large sections of the mine. These scenarios have been studied extensively at the Bruceton Experimental Mine (BEM) and the Lake Lynn Experimental Mine (LLEM) of the NIOSH Pittsburgh Research Laboratory. The minimum quantity of methane required to initiate a coal dust explosion was studied in 1930 in the BEM [Rice et al. 1933; Nagy 1981] and then later in the LLEM, whose cross-sectional area (130 ft2) is over twice that of the BEM [Sapko et al. 1987a]. Studies conducted in the BEM closely simulated conditions that existed in operating mines in the early 20th century. The later tests in the 20-ft-wide entries of the LLEM simulated the geometries of modern mines with advanced roof support technology. The data from the BEM tests show that 13 ft3 was the minimum quantity of methane at the face that, when ignited, would disperse and ignite coal dust. In the BEM, this amount of methane was mixed with air to form a total flammable volume of about 140 ft3 of a 9% methane-in-air mix-ture. In the wider entries of the LLEM, about 37 ft3 of methane was required to disperse pure coal dust and start a self-sustained coal dust explosion. This amount of methane was mixed with

Jan 6, 2006

HISTORIC SIGNIFICANCE OF EXPLOSIVES TO MINERAL PRODUCTION The ancient method of breaking rock was to build a wood fire against the face, heat the rock through and then pour water on the heated ore-bearing rock to cause it to break by tension. It was too slow and costly as the forests around the mines were cleared and transport of wood became difficult. Black powder had been used for 300 years as a gun propel- lant. ('Black' after Berthold Schwartz, a German monk, Figure 1, and the inventor of the gun who was given the epitaph `Here lies Berthold the Black, the most abominable of inhumans who by his invention has brought misery to the rest of humanity'). Only at the beginning of the 17th Century, black powder was introduced for loosening rock in European mines. In 1802 Dupont started black powder manufacture on the Brandywine Creek. The ignition train of powder was enclosed in goose quills, straws, rushes, paper or wooden tubes. The time interval between igni- tion and blast was pure speculation.

Jan 1, 1988

By F. E. Heuze

This article deals with the effects of high-explosive and nuclear explosions in rock masses. We first highlight the strong influence of geological discontinuities, such as joints and faults, on ground motion characteristics. Then, we briefly introduce the Discrete Element Method, as a new technique for numerical simulations. II is shown to be far superior to continuum-based approaches, when dealing with the dynamics of discontinuous media such as jointed rocks. Finally, we simulate the ground effects from a generic contained nuclear explosion, which bears some similarity to the SHOAL event in granite. This calculation is intended to emphasize the influence of the near-source geology on the distribution of energy, and on the motion at various azimuths in the medium.

Jan 1, 1991

By R. Karl Zipf

A fatal explosion in a sealed area at the Sago Mine in 2006 prompted researchers and regulators in the United States to re-examine the requirements for explosion-resistant mine seals. Seals are used in underground coal mines to isolate abandoned mining areas from active workings. Prior to the Sago disaster, mining regulations required seals to withstand a 140 kPa explosion pressure. Recent research at the National Institute for Occupational Safety and Health (NIOSH)Pittsburgh Research Laboratory showed that pressures from explosions can far exceed this pressure. U.S. mining regulations now require much stronger seals. Current research focuses on understanding the science, engineering and management of sealed areas of coal mines. Scientific efforts seek understanding of how explosive methane-air mixtures accumulate using measurements and models of the sealed area atmosphere. Additional scientific efforts aim to understand the explosion pressures that can develop using a combination of numerical modeling and experiments. Engineering efforts aim to produce design guidelines for seals that can resist the new higher pressure design criteria. NIOSH researchers are also developing guidance for monitoring of sealed area atmospheres and inertization of potentially explosive gas mixtures within sealed areas. This paper seeks to encourage scientific discussion among international peers since preventing explosions within sealed areas is of interest to underground coal operators and regulators.

Jan 1, 2009

By George S. Rice

Foreword Explosion hazards differ widely in the mines of different fields or coal basins. They also differ as between different mines in the same basin or fold, because of variations in gas entering the mines, and because dust conditions and explosion hazards are affected by the mining methods employed and the organization of the work. It is unquestionably true, however, that there are greater differences in explosion hazards in mines of different coal fields or basins than between different mines of the same field or basin. In these respects, the coal fields and individual mines in Alberta are not exceptional. The same conditions obtain in various countries where coal is mined, and are found in single States, as for example in Colorado, where coals are mined ranging in character from sub-bituminous to anthracite, and in attitude from flat horizontal to steeply pitching beds. The U.S. Bureau of Mines, at its experimental mine near Pittsburgh, Pa., has made large-scale tests of the relative explosibility of dusts of coals, ranging in rank from Wyoming sub-bituminous coal containing 19 per cent moisture, to anthracite from Pennsylvania, and including samples from a mine in the Crowsnest Pass district, B.C., and from a Vancouver Island mine. The Bureau has also made similar tests of the dust of coal from a Yorkshire mine which the British Safety-in-Mines Research Board uses as standard.

Jan 1, 1927

By Wang Xuguang, Tian Ruigi, Xiong Shangbin, Xiong Daiyu

Combining action features of explosive shock with those of natural lignocellulosic biomass structure, we have successfully developed a new explosive shock dilatation and separation technique for pretreatment of natural lignocellulosic materials in the laboratory. Based on a brief introduction to the technical background and experimental procedure of this new method, some preliminary experimental results are given and discussed: the scanning electron microscope (SEM) qualitative observation results show that for treated natural lignocellulosic sample such as corn cob etc., their length of fibre bundle shortens, fibre bundle arrange disorders, biomass appearance and structure of samples largely change to be dilatation and loose state. The dilute acid hydrolysis quantitative measure results show that for treated samples, the overall yield of the reducing sugar largely increases, hydrolysis rate of corn cob sample is over 80%, rate and speed of hydrolysis are increased by times.

Jan 1, 1998

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By Zhiyuan Ma, ZUI WANG, Xincheng Hu, Jianwei Cheng, Junhong Si, Yi Qin, Gao Ke

The harmfulness and destructiveness of mine gas explosion is quite serious, which is the first of all kinds of coal mine disasters. Once the gas explosion occurs, it could instantly generate explosion shock waves, high temperature airflows, and disaster gases, which cause the destruction of underground ventilation structures, disruption of airflow direction in a mine ventilation network, and miners’ deaths by asphyxiation. As an important barrier to prevent the spread of accidents caused by the gas explosion, the safety and reliability of the mine seal affects the mine’s production and the health of workers. Due to the demands of coal mine production and transportation, a large number of longitudinal and horizontal roadway networks have been developed underground. There are not only many flat and straight roadways in the complex roadway network structure, but also a large number of different types of bifurcations and bends. Once a gas explosion occurs, the impact of the blast waves on the mine seal after passing through the complex path is difficult to determine. Therefore, this paper establishes a numerical model of bifurcated and cornered roadways and studies how the impact of gas explosion shock waves on the structure of sandwich mine seal after passing through different types of bifurcated and cornered roadways. The damage state of sandwich mine seal is analyzed. The researching finding could prevent and manage the spread of gas explosion disaster, and improve the disaster mitigation of mine explosion accident.

Jul 11, 2023

By E. J. Gleim

[THE ORGANIC act under which Federal Bureau of Mines was established provided for the investigation of the safe use of electricity in mines. Each Congress appropriates funds for conducting this investigation. As part of this investigation, electrical apparatus used in mines is studied to determine if its operation and use might introduce a hazard. From this study, certain safety standards have been developed. These standards, established with the aid of both the manufacturer and user of such apparatus, are published in schedules, and apparatus that complies with the requirements set forth these schedules is classified as "permissible." This term is defined to designate apparatus as "completely assembled and conforming in every respect with the design formally approved by the Bureau of Mines." In the judgment of the Bureau, the manufacturers of such apparatus have adhered to certain minimum standards of safety in supplying a product that when properly used and maintained is safe for operation in mines where flammable gas or coal dust may accumulate. This work of the Bureau of Mines for increasing safety does not make it obligatory for manufacturers of mine equipment to produce only that of permissible classification. Before the effective date of the Federal Mine Safety Code,5 the Bureau sought to promote safety by recommending that mine operators install permissible equipment in gassy mines as a preventive measure against gas and dust explosions initiated by electrical equipment. For some years, the mining laws of several States have prescribed the conditions under which permissible equipment must be used. The Federal Mine Safety Code requires that ?all new electric face equipment and replacements of equipment purchased for mines where nonpermissible equipment is now being used shall be of a permissible type approved by the United States Bureau of Mines,]

Jan 1, 1955

By Thomas H. Dubaniewicz

(XP) enclosures to enclose electrical ignition sources to prevent propagation of an internal methane-air explosion to a surrounding explosive atmosphere. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a lithium-ion battery thermal runaway test within a modified MSHA-approved XP enclosure to assess thermal runaway containment. Thermal runaway produced jet flames emanating from the cover joint at several locations and distorted the cover joint and bottom plate of the enclosure beyond allowable limits. The test demonstrates that XP enclosures may not provide adequate explosion protection against lithium-ion battery thermal runaway. This paper suggests some approaches to mitigate the hazard.

Feb 1, 2024