Search Documents

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By B. R. Stewart

The exclusion of coal fly ash from regulation as a hazardous waste has led to increased interest in returning ash to the coalfields for co-disposal. A multi-year column study used coal refuse with high potential acidity (4% total-S), and two alkaline ashes in various bulk-blends. The unamended refuse acidified rapidly, producing acidic (pH 1.7) leachates, high in dissolved metals. Treatments blended with sufficiently high amounts (20 to 33%) of alkaline ash produced alkaline (PH >8.4) leachates with low metal levels, while lower ash blending rates acidified over time to produce metalliferous leachates. Examination of solid materials indicated that pyrite oxidation was occurring to some extent in all treatments. A regression equation (r = 0.95) was developed to estimate time to net acid release for mixtures of these materials. Ash alkalinity and refuse potential acidity must be balanced to insure water quality for co-disposal environments, or the ash materials should be isolated away from acidic drainage waters.

Jan 1, 1997

By B. R. Stewart, L. W. Zelazny

The exclusion of coal fly ash from regulation as a hazardous waste has led to increased interest in returning ash to the coalfields for co-disposal. A multi-year column study used coal refuse with high potential acidity (4% total-S), and two alkaline ashes in various bulk-blends. The unamended refuse acidified rapidly, producing acidic (pH 1.7) leachates, high in dissolved metals. Treatments blended with sufficiently high amounts (20 to 33%) of alkaline ash produced alkaline (pH >8.4) leachates with low metal levels, while lower ash blending rates acidified over time to produce metalliferous leachates. Examination of solid materials indicated that pyrite oxidation was occurring to some extent in all treatments. A regression equation (r2 = 0.95) was developed to estimate time to net acid release for mixtures of these materials. Ash alkalinity and refuse potential acidity must be balanced to insure water quality for co-disposal environments, or the ash materials should be isolated away from acidic drainage waters.

Feb 24, 1997

By H. Marquis

This paper is concerned with an analysis of a number of failures of large-size, hypervelocity light gas gun chambers and barrels. A brief description of the light gas gun principle and of the various types of guns is first given. The failures and the investigations carried out are then described in detail, with the failures divided into two groups. The first group comprises those failures caused by certain conditions to which the guns may be submitted, and includes, for example, severe local heating of the bore surface causing hardening and cracking of the steel. These conditions were accidental and steps were taken to prevent them. The remaining failures were due to faults in the material or in the heat-treatment, manufacturing or assembling procedures. Specific problems, such as hydrogen embrittlement, and the use of high strength gun barrels above their ductile-brittle transition temperature by preheating prior to firing, are briefly considered. Some interesting observations are also presented on the use of surface markings, and angles of fracture of large fragments, as an

Jan 1, 1962

By Mark Board

INTRODUCTION As the world's supply of near-surface metalliferous ore bodies is depleted, more emphasis must be placed upon mechanized bulk systems of underground mining. In particular, block caving is becoming increasingly important as a method of mining low to moderate grade deposits at depths of somewhat less than 1219 m (4000 ft). 00 ft). The block caving method requires that the ore body be completely undercut, thereby removing its means of support and inducing failure which progresses from the undercut to the ground surface. As the span of the under- cut increases and the weight of the overlying crushed ore body becomes greater, large stresses are induced on slusher and haulage drifts. Stability of these drifts is critical in block caving operations and often proves to be an extremely difficult task (Kendorski, 1976; McWilliams, 1975). Slusher drift maintenance can be costly, often exceeding that of the original support costs. This chapter analyzes the ground support problems of an Arizona block caving mine. The mine presently uses monolithic concrete liners as a support method. Failure of the liners occurs as the undercut approaches, thus initiating a maintenance problem which will continue until the ore body is depleted in that block or panel. To examine this problem, a simple analysis of the stresses induced by the advancing undercut was per- formed. Utilizing a design method developed by Dixon ( 1973, 1974), the calculated stresses were used to deter- mine the minimum thickness required for varying section shapes of unreinforced concrete liners. It is found that the thicknesses required for stable linings are not economic. Recently developed empirical methods of support de- sign are utilized (Barton, 1974; Bieniawski, 1973) and compared to the analytical method. A final discussion of alternative methods of support is given with recommendations for the use of passive or "yielding" support methods. LAKESHORE MINE (GENERAL GEOLOGY) The Lakeshore copper property is located in Pinal County, AZ, approximately 45 km (28 miles) south of Casa Grande. The Lakeshore deposit is a porphyry cop- per similar to others in Arizona. The ore body consists of disseminated chalcopyrite and fracture fillings in quartz monzonite porphyry (QMP), Cretaceous volcanic (KVS), Precambrian diabase, and Mescal limestone. The ore body has been divided into three distinct zones of mineralization which have been termed (South, 1972) the oxide zone, the sulfide zone, and the tactite zone. The oxide zone occurs in the upper portions of the ore body and consists primarily of leached and oxidized quartz monzonite porphyry and Cretaceous sedimentary and volcanic rocks. The sulfide zone underlies the oxide zone and includes all quartz monzonite porphyry and Cretaceous rocks which have not been oxidized. The thickness of the sulfide zone is variable and ranges from about 61 to 122 m (200 to 400 ft). The tactite zone occurs in a series of Paleozoic metasediments consisting of tactite, quartzite, diabase, hornfels, and dikes of quartz monzonite porphyry. The tactite zone is highly variable in thickness and underlies the Cretaceous volcanic and sediments throughout the mine. Together, the tactite and sulfide zones are known as the thick or tall sulfides. The greatest support stability problems occur in mining of the tactite zone and are therefore the subject of the remainder of this chapter. MINING METHOD The Lakeshore mine is a block caving mine utilizing a panel caving method. The present mine consists of two

Jan 1, 1982

By R. D. Lrwin, W. M. Mullins, S. Venugopa, J. C. Malas

"Physical models for acoustic emission (AE) are introduced and expressions are derived to predict AE activity from such parameters as applied stress, strain and strain-rate. These models are then incorporated into a visco-plastic finite-element simulation program, and the acoustic emission event rate generated during metal forming operations are predicted. Simulation results are presented for upsetting operations on a typical C-Mn type steel for various friction and die geometry conditions. The AE model predictions compare well with the limited available experimental results reported in the literature and demonstrate that AE signatures can be reliably simulated. The signatures predicted for metal forging are fairly insensitive to processing parameter changes. This suggests that AE event rate monitoring may not be well suited to process monitoring for forging. However, the size of the features is conjectured to influence the frequency content of the AE signals. Thus, since current simulations include only the ability to predict the number of events for a set of processing conditions, future work is required to simulate the duration and magnitude of acoustic events. Fourier analysis techniques may then be applied to investigate correlation with microstructural features.IntroductionThe open loop control system method for deformation processing design, as described by Malas et al. [1 ], consists of several steps in series to achieve the final design. The first step uses microstructure development models to determine the optimum deformation path to achieve the desired final microstructure. The second step, the process model, calculates the processing parameters required to achieve this deformation path. Finally, the metal-working system uses the required processing parameters to produce the part. Figure 1 shows this in block diagram form"

Jan 1, 1997

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By T Raynlyn, J J. Campbell, J M. Young

In order to correctly predict the performance of beneficiation processes, such as hydrocycloning or ultrasonic treatment of iron ore fines, it is important to understand possible changes in size distribution, mineral composition and textural peculiarities. During beneficiation processes, iron ore can be subjected to various physical actions which may result in changes in size distribution. In the case of soft or friable ores, attritioning and/or deagglomeration may have a significant effect on both separation performance and product stream specifications. Optical image analysis tools, which give statistical information on a particle by particle basis, can help in better understanding the response of the ores to these processes. An experimental study has been conducted to investigate the response of a haematitic-goethitic iron ore to a combination of stirring and ultrasonic treatment. The effect of stirring and ultrasonic treatment on the size and mineral distribution has been quantified using image analysis and automatic ore texture classification. This approach has been applied to several size coarse fractions of the initial feed and product. The results show that, following treatment, the mass proportion of ore texture classes which contained higher amounts of ochreous goethite and kaolinite had significantly decreased compared with that in the feed, while the proportion of texture classes where haematite was the major mineral had increased. Liberation analysis also showed a significant increase in the proportion of particles with more than 95 per cent haematite and vitreous goethite.

Jan 1, 2007

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays.

Jan 1, 2013

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Khaled Mohamed

Resin-grouted bolts serve as a crucial means of stabilizing yielded coal ribs in underground coal mines. A comprehensive investigation into their efficacy was undertaken by a collaborative effort between the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST). This study involved pull-out tests in multiple locations, including six coal mines and the NIOSH research mine. A total of seventy-three (73) tests were conducted, of wide range of anchorage lengths, ranging from a short encapsulation length of 0.305 m to a fully grouted encapsulation length of 1.524 m. The test findings indicate that when short encapsulation bolts are installed at high rotation speeds, their anchorage capacity is significantly reduced, leading to failure at the bolt-grout interface. Conversely, when these bolts are installed at lower rotation speeds, they exhibit greater capacity, with failure occurring at a higher anchorage load equivalent to the yield load of steel rebar. No matter what the rotational speeds were used during bolt installation in this study, the fully grouted bolts consistently experienced failure at the ultimate load of the steel rebar. Most of the tests carried out on partially grouted bolts with anchorage lengths of 0.610 - 0.914 m have shown behavior patterns like the fully grouted bolts, although exhibiting reduced stiffness. The outcomes of this research offer a profound insight into the ways in which resin-grouted bolts enhance the stability of coal mine ribs.

Feb 1, 2024

By Peter V. Barr

Despite the advent of modem firing control systems reheating furnace operations frequently allow significant thermal excursions in the discharged slabs or billets after furnace delays. Although HSM furnaces are not immune to this and other related problems, mini-mill operations are most vulnerable due to their more frequent delays and (often) less sophisticated control systems. In order to reduce these problems control systems will commonly include a thermal model, operating either on-line (interacting directly with the controller logic) or in an advisory, off-line mode. Using a new 'fast' thermal model, the paper examines the thermal response of a typical mini-mill furnace during both delays and the subsequent recovery period. A variety of firing strategies are explored and compared on the basis of maintaining thermal excursions within allowable limits for rolling. Other factors, such as the potential for overheating of billets within the furnace during delays and the overall thermal state of the furnace, are also considered in some detail. Although common practice, the use of conventional thermocouple zone temperatures for furnace control during and after delays is shown to be a dubious proposition. Keywords: Reheat Furnace, Modeling, Process Control

Jan 1, 2003

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach and discrete fracture network (DFN) model, generated from the field surveys, are novel methodologies to study fracture rock mass behavior. In this paper, SRM and DFN methodologies were used to understand the influence of natural fractures on the mechanical response and failure mechanisms of stone mine pillars. First, a multi-stage up-scaling procedure with the homogenization process is established. Later, a stochastic sampling process on the SRM model to have further insight on the stone mine pillar mechanics is performed. Two-dimensional Universal Distinct Element Code (UDEC) is utilized to represent intact rock with the Voronoi-Trigon discretized blocks and to capture fractured rock mass behavior. The laboratory-size limestone mine rock specimens are systematically up-scaled to the average width of the field-size stone mine pillars. Then, the DFN model, generated from field data, is sampled to construct the SRM of the field-size pillars. By doing so, the effect of discrete discontinuities on pillar stability is studied by assessing the pillar strengths and failure mechanisms in various width-to-height ratios.

Jul 8, 2022

By M I. Pownceby, N Karimian, J R. Manuel, M J. Peterson

The CSIRO ore classification scheme for Pilbara ores was used as a reference frame to target recognisable ore types/textures with potentially elevated phosphorus content for detailed analysis. Particles of each individual ore texture were separated from a Brockman high-P ore and each class was characterised using methods including XRF, XRD, EPMA and synchrotron-based XAS. Results were then correlated with optical microscopy and hand specimen identification to establish any relevant associated mineralogical phases and/or textures. This represents a more systematic approach to identification of high-P ore components based on particle and goethite type and texture. The information can then provide the basis for more targeted P-removal strategies factoring in the relationship between particle/ore texture and phosphorus deportment

Sep 18, 2023

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

Froth flotation is widely used for the separation of particulate materials in the world. It is a complex process whose operational behaviour in process plants is difficult to predict. A comprehensive phenomenological dynamic flotation model was presented at the 1982 IMPC. This model uniquely linked the particle/bubble interactions and water transport phenomena to the flotation cell hydrodynamics. The model was used as a dynamic framework to analyse and develop process optimisation strategies. New developments in mineralogical characterisation, real time information management systems and data validation simplify the implementation of flotation technologies for mine to mill grade recovery optimisation. With recent developments in software programming, dynamic simulation enables process engineers to develop process alternatives interactively. This paper presents such an implementation of current process analysis tools and an updated froth flotation dynamic model. It demonstrates how this new environment can be used to improve our technological knowledge of flotation, eg alternative bubble/particle attachment and detachment microprocesses can be incorporated. The dynamic flotation model has several manipulated variables (such as feed flow rate, per cent solids, aeration, wash water flow rate, frother flow rate, specific power energy (impeller speed/delta pressure), cell geometry and tails flow rate) and evaluates the dynamic effects of these variables on grade and recovery.

Jan 1, 2005

In six deep hard coal mines situated in the coal district of the Saar and Lorraine, Saarbergwerke AG produce annually 9 to 10 million tons of coal. The coal is either coked or fired in power plants. Comprehensive planning work is done for the producing coal faces, 15 stone drifts and 60 seam headings. The computer can assist in drawing up the short- and medium-term planning by taking over, on the one hand, work done so far by hand and by supplying, on the other, additional information. The computer can draw up time schedules, can do quantitative calculations, can draw up plans for the em- ployment of manpower, machines and other equipment, and can calculate cost and earnings. It is ensured that all part plans are always adjusted to each other. Because of the volume of work involved, planning in this form and extent becomes possible only by the computer. Especially with the periodical continuation of planning, the new system facilitates the work to be done. The ideas of the planning engineer are and remain the basis of all planning work and the computer gives him an aid to assist him with calculations, report writing and feasibility studies.

Jan 1, 1977

By C. Pichler, A. Ressler, D. Gregurek, A. Spanring

In order to improve the refractory lining life at one of the RHI key customer test procedures were developed within a two years collaboration project. In the first year of cooperation detailed refractory corrosion work in the rotary kiln with Ca-ferritic slag was performed. The main results of the second year of cooperation, reported in this article, involve a detailed testing work with nickel matte and pre-selected refractory brands which was performed in TBRC. A first part of this work was a complete chemical and mineralogical characterization as well as FactSage calculations carried out on provided matte samples. According to these results testing in the TBRC was realized at different process temperatures with several magnesia-chromite bricks. Based on the mineralogical investigation a high chemothermal load caused by sulfidic matte resulted in a deep reaching infiltration of the brick microstructure and partly corrosion of main brick components.

Jan 1, 2015