Search Documents

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

"A commercially available through-the-earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electricfield (E-field) sensing to send text-based communications through two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivities. IntroductionWireless, through-the-earth (TTE) communication technology is designed to achieve point-to-point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. Using this approach, communications are established without the need for intermediary communications infrastructure. As a result, TTE systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers, 1924; Pittman, Church and McLendon, 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon, 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker, 2006; Wadley, 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer, 1973; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Jakosky and Zellers, 1924; Large, Ball and Farstad, 1973). Although commercially developed TTE systems have demonstrated the ability to communicate in a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker, 2006; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Ilsley, Freeman and Zellers, 1928; Jakosky and Zellers, 1924; Yenchek et al., 2012)."

Sep 1, 2016

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

By W. C. Smith

Over the past several years, the Bureau of Mines has conducted studies on the performance of fully grouted resin bolts In underground mines. The effectiveness of resin-grouted bolts in maintaining a competent roof, even in weak rock, has been well documented in the literature. Recent Bureau studies have evaluated the affects of shortened grout columns on bolt behavior in a variety of rock types (1, 2, 3). The application of partial grout columns to primary roof support systems has been introduced as a viable alternative to fully grouted bolt systems in some mines. The point-anchored resin bolt and combination bolt represent such alternatives. While both systems usually employ some mechanical interlocking system, their primary difference lies in the length of resin column used. Point- anchor systems rely on an anchoring device that is a short length of resin column of 2 feet or leas. Combination bolts, on the other hand, often require 3 feat or more of resin column. Resin migration into voids and fractures intersecting the borebole wall is a major problem when installing fully grouted bolts in weak roof rock and can result in a reduced column length that provides reduced anchorage. The relationship between column length and anchorage integrity deserves closer study. The Denver Research Center of the Bureau of Mines has examined the load- carrying capabilities of resin-grouted bolts in weak strata. Pull tests were performed on about 900 resin-grouted, 4- foot-long bolts with column lengths ranging from 6 to 48 inches. The practical performances of 8 different column lengths were evaluated for 10 mines under in sit" conditions using data obtained from standard pull tests. In addition criteria are discussed, including engineering properties of the host rock for designing safer and more effective grouted bolt installations.

Jan 1, 1987

By G. Chisakuta, P. Bwando, G. Mitshabu

By the end of 2022, the south-eastern Copper Belt region of the Democratic Republic of Congo was host to more than 40 small, medium, and relatively large sized copper solvent extraction sites. To date, solvent extraction reagents supplied in this region have never exceeded 50% of ketoxime content. We generated laboratory extraction and strip isotherms and used these with the BASF IsocalcTM modelling software to assess the benefit of using higher ketoxime blends on the main metallurgical performance indicators such as copper recovery and net transfer. Pure ketoxime extractants combine a relatively low strip point and a decent loading capacity, which are most effective as the pH of the pregnant leach solution gets closer to 2.

Jan 1, 2023

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, N. Esmaeili, R. Hejazi, A. D. Ahmadabadi

The main challenges in most low grade iron ore deposits are finding the optimum flowsheet for beneficiation to achieve a final concentrate from both technical and economic viewpoints. Dry preconcentration techniques are being used to assist in reducing the amount of ROM feed to the plant. In this paper the benefits of utilising a dry cobbing magnetic separation technique for upgrading the product of HPGR in a closed circuit with dry screen 4 and 1.4 mm by performing a pilot scale test work was investigated. The experimental test work was done on two sample types of Yogi BIF magnetite iron ore located in Western Australia. Prior to magnetic separation studies, detailed characterisation of the feed materials including physical, chemical, mineralogical and magnetic properties were carried out. Furthermore, the effects of process parameters: drum rotation speed (1.5, 2.5 and 3.5 m/s), magnetic field intensity (1100 and 3800 gauss) and feed size (minus 4 and 1.4 mm) were investigated. The results revealed that sample type1 with 33.90% Fe could be upgraded to 41.51% Fe by using a stage of 1100 gauss dry magnetic separator with 69.12% weight recovery and 84.36% Fe recovery at a size of 4 mm. Also for sample type2, it is possible to increase Fe grade from 29.84% to above 36.68% with 75.58% weight recovery and 90.32% Fe recovery by applying one stage of 1100 gauss dry magnetic separator to a 4 mm size sample. Keywords: Banded iron formation (BIF), pre-concentration, dry cobbing technique, magnetic separator

Jan 1, 2020

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By H. K. Conn

This paper discusses briefly the evaluation of chrysotile asbestos deposits in ultramafic rocks. Such deposits are limited to serpentinized peridotite and/or dunites. The purpose of any evaluation is to determine whether a deposit contains sufficient ore mineral to justify profitable exploitation. Dimensions of a mineral zone are established by conventional methods, such as mapping, ground magnetic surveys, diamond drilling or underground exploration. The value of the contained asbestos fibre Is dependent on numerous physical properties such as fibre length, strength, flexibility, as well as the actual amount of fibre present. The determination of grade is difficult. The Quebec Standard Test (Q.S.T.) is used to grade fibre according to the proportionate lengths of fibre present. A method of visual vein counting allows calculation of an approximate percent fibre together with a simulated Q.S.T. Various drilling methods are discussed, diamond drilling is favored. Bulk sampling is required to determine fibre quality. Correlation of visual techniques and laboratory methods are often difficult. Reasons for any variance are discussed. Underground bulk sampling of most potential ore zones is strongly recommended to confirm the viability of the property. Evaluation of slip fibre deposits requires greater reliance on laboratory testing as visual methods are difficult to apply. Cross fibre has greater inherent strength.

Jan 1, 1971

By Neha Shukla, Nikhil Dhawan

The current study examines the extraction of rare-earth elements from trichromatic phosphor of discarded tube lights via baking processes. The Y2O3: Eu3+ (YOX) and BaMgAl10O17: Eu2+ (BAM) phases completely decomposed during acid and alkali baking with > 90% Eu and Y extraction. Prior, selective acid leaching of the YOX phase enhanced the acid baking process at a lower temperature (< 230 ℃). Feed acid baking showed a maximum 87% Tb, 36% La, and 17% Ce extraction at 500 °C, 0.5 h, 1 ml/g H2SO4, and alkali baking yielded 16.1% Tb, 86% La, and 73% Ce at 300 ℃, 0.5 h, 50 wt.% NaOH. The acid baking of the acid-leached phosphor yielded 72% Tb, 95% La, 63% Ce, ~ 95% Y, and Eu extraction at 300 °C, 0.5 h, 1.05 mL/g H2SO4. Lower Tb extraction during the acid baking of acid-leached phosphor can be attributed to the formation of Ba3Tb( PO4)3 and BaTbO3 phases. Insoluble Si3Tb5 phase formation and partial decomposition of CeMgAl11O19: Tb3+ (CMAT) phase in the alkali baking route leads to lower Tb extraction. The acid baking process is suitable for extracting Tb, Eu, and Y, whereas the alkali baking process is suitable for La and Ce. The thermal analysis of phosphor and flux interaction depicts that alkali baking is less energy-intensive than acid baking. In comparison, the one-step acid baking process and the two-step alkali baking process yielded desirable extraction results (87% Tb, total RE (rare earth) 78.5% and 50.4% Tb, total RE 59.3%). The product yield in the acid and alkali baking route of feed, acid-leach phosphor is 36%, 29%, and 39%, 28.2%, respectively, with ~ 98% mixed rare-earth oxide purity.

May 5, 2022

By Luane Isquierdo Ferreira Holanda, Lucio Fabio Cassiano Nascimento, Luis Henrique Leme Louro, Sérgio Neves Monteiro, Alaelson Vieira Gomes, Édio Pereira Lima Júnior

In the present study,we used natural fibers malva (Urenalobata, Linn) in 0, 15 and 30 vol.% as reinforcement of epoxy matrix composites to ballistic application. Ballistic efficiency of these composites was assessed by measuring the energy absorbed and residual velocity after impact 9 mm FMJ ammunition projectile, aiming to compare with traditional materials, such as: aramid fabric Kevlar™ used in vests for personal protection. The results showed by visual analysis and scanning electron microscopy (SEM) that the main active failure mechanisms in composites were delamination layers and fiber rupture. In test groups can be seen that the absorbed energy and the residual velocity varies with the fiber percentage used. Compared to aramid there is both a gain in weight and cost of the ballistic armor, which makes the fiber malva a promising material applications involving personal protection against 9 mm caliber ammunition.

Mar 1, 2017

By William G. Freeman

In comparison to many mineral commodities, barite has a low unit value. It is mined and sold in low volumes in high-grade (90-98% BaSO4) forms to basically one industry that uses approximately 75% of the free world production. Based upon the above criteria, all factors must be considered in determining if a barite deposit is economical; such as, the type of deposit, mining and milling methods required, transportation to the markets, tariffs, local political conditions, etc. In other words, barite mines are made--not found. The length of this paper precludes any indepth discussion of geology, mining and metallurgy of barite. Most of this information can be found in data already published, such as D. A. Brobst&apos;s bulletin1 on the Barite Resources of the United States.

Jan 1, 1971

By Askari-Nasab, D. Checkel, K. Awuah-Offei

Life Cycle Assessment (LCA) is an emerging environmental management tool for examining environmental impacts from cradle to grave. In this paper, LCA is used to evaluate the acidification potential (AP) and global warming potential (GWP) of belt conveyors and truck haulage systems in a surface gold mine using the ISO 14040 standards. The results show that, for AP, the truck system has 32 kg of equivalent SO2 per functional unit, compared to 8 kg for the conveyor system. However, for GWP, the conveyor has 2,820 kg of equivalent CO2 per functional unit, compared to 648 kg for the truck option.

Jan 1, 2009

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By Jack S. Greber

The mining industry generates an estimated 2.3 billion tons of solid waste each year and the total accumulated mineral resource solid waste at both active and inactive mine sites, approaches 30 billion tons. Five industries generate 85 percent of mine solid waste: copper, phosphate, iron, uranium, and coal. Over the past several years, the Federal government has shown increasing interest in the proper disposal of solid wastes generated by the mining industry. Three new pieces of federal legislation have been passed recently beginning with the most comprehensive regulatory authorization passed in 1976, the Resource Conservation and Recovery Act (RCRA) which has been amended to the Solid Waste Disposal Act Amendments of 1980. RCRA is implemented and enforced by the Environmental Protection Agency (EPA) and intended to control municipal and industrial solid wastes. Next came the passage of the Surface Mining Control and Reclamation Act (SMCRA) of 1977 which is implemented and enforced by the Department of Interior to control coal surface mining and the surface effects of underground coal mining, and finally, the recent Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 implemented by EPA and enforced by the Nuclear Regulatory Commission (NRC) to control uranium mill tailings disposal.

Jan 1, 1981

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By K. H. Singh

The addition of new data and corrections can be made under the control of a simple editing session. All programs for this system are written in FORTRAN and executabe "MACROS".. After the addition of new data, the whole file Is reinitialized to update the binary file and cross-reference tables. Updating the binary file involves rerunning the initializing program. The creation of graphic plots like cross sections and plan views is menu-driven from a terminal and very user-friendly. Small files containing not more than 10,000 entries (survey and assay points) are suitable for this setup, particularly for computers with less than 2 Megabytes of real and virtual memory. The largest file processed contained 35,000 lines of survey and assay information and required 4 megabytes of virtual memory. Working with this size file slows down the time for the creation of plots and cross sections. Another independent system is more akin to a financial type of data base. It was installed in one Anaconda mine as part of the operation&apos;s inventory, warehouse, day-pay payroll, and purchasing data bases. It is a highly hardware-dependent system, in particular, IBM&apos;s CICS/VS (Customer Information Control System/Virtual Storage). This is a true relational data base that optimizes storage requirements, supports online inquiry, update, data entry, and data security. While this system has been tested and proven in accounting applications, it requires programming expertice in PL/I and other CICS utility programs. It is well suited for huge data bases (like the 35,000 lines of data), but cumbersome for small engineering files.

Jan 1, 1985

By K. Perry, R. Eades

"Highwall miners continue to be implemented by operations to increase recovery, improve margins, and justify higher stripping ratios as high quality surface reserves become increasingly rare. Many times, operations facilitate projected underground operations by leaving an intact highwall for development purposes. These facts result in larger highwalls that are left standing for increased periods of time prior to reclamation. As a consequence, worker exposure and risk is also elevated, resulting in higher potential for accidents or fatalities relating to surface highwalls. Highwall stability is a complex issue, dependent on both geologic and mining factors. Dynamic numerical modeling offers the capability to assess possible stability issues related to blasting-induced ground vibrations. Research has been conducted to evaluate the effect of highwall stability due to ground vibrations from blasting events. Additionally, the relationship of amplitude and frequency, and their impact on highwall stability is investigated. The results of this modeling indicate that amplitude has little impact on stability. However, frequency has a significant impact on highwall stability. INTRODUCTION The number of mining fatalities has declined since 2010, and 2016 is currently on pace to continue this trend (MSHA 2016). This decline can be directly correlated to the decline in surface mining activity and the overall decline of the coal industry. However, since 2002 the percentage of surface coal mine fatalities associated with highwall activities remains relatively high, constituting approximately 15% of all surface mine fatalities. 2014 was the first year with a highwall failure fatality since 2011. Most recent surface coal mining fatalities are associated with machinery and haulage. Table 1 provides a summary of the total surface coal mining fatalities, and the number of highwall failure fatalities dating back to 2010.Highwall stability is a complex issue, dependent upon geology and geologic discontinuities within the rock mass, along with highwall geometry, standing time, and applied stresses. Another possible concern that has not been previously investigated is the effect of blasting-induced stresses on highwall stability and the stability of web/barrier pillar systems as a result of ground vibrations from blasting events. Many modern surface coal mines employ numerous extraction fronts that rely on blasting for primary rock breakage. This results in highwall and highwall pillar systems experiencing blasting-induced stresses of many different types and magnitudes."

Jan 1, 2017

By F. Schott, M. James, G. May, E. Baker, C. Johnson, R. Bauer

Explosive demolition typically utilizes cutting charges to sever columns, detonating cord to time charges and provide an initiation path, and dynamite as a kicker charge. The kicker charges of dynamite are used to “move” columns out of alignment, causing collapse. Demolition projects involving dynamite can pose significant health and safety risks to workers and the public. Nitroglycerin in dynamite can cause dizziness, fainting, and other health problems. Moreover, dynamite placed directly on columns can result in fragmentation and cutoffs, preventing other charges from being initiated and resulting in incomplete demolition. Fragmentation can occur from columns and travel significant distances from the initiation point, sometimes reaching hundreds of meters away. This fragmentation can pose serious dangers to anyone in the vicinity, including workers and members of the public, as the debris can cause severe injuries and property damage. The force and velocity of the fragmented material can be unpredictable and difficult to control, making it important to take proper safety precautions and consider alternative demolition methods that minimize the risk of fragmentation. Previous work concluded that casing charges in water showed that a reduced dynamite charge mass could still successfully kick the charge out of alignment. This study aims to investigate the use of Pentolite boosters in water-cased charges as a safer alternative to dynamite-based demolition. The research involved testing various amounts of dynamite and pentolite boosters in water to compare their effectiveness in moving a hanging W-beam, which swung freely like a ballistic pendulum. Water-cased charges consistently move the column at a higher velocity than the traditional dynamite charge placed directly on the column. The method of water-casing increased the area of impact and impulse felt by the column, improving demolition efficiency when compared to traditional demolition methods as found in previous studies. Pentolite water-cased charges moved the column at 7.8 meters/second (m/s) while the dynamite water charge moved the column at 5.9 m/s. The increased strength and explosive properties of the pentolite contributed to this increase in velocity. This study showed that it is feasible to remove dynamite from demolition projects by utilizing pentolite boosters and that when considering safety, explosive properties, and effectiveness, pentolite boosters can be cost effective as well.

Jan 1, 2024