Search Documents

By Robert J. Watters, Peter C. Kelsall, Joseph G. Franzone

Two separate studies investigated the compressive strength of basic igneous rocks and its relation to index properties such as porosity, density and soundrave velocity. The rocks tested were weathered dolerite from S. W. England and vesicular lavas from California. In both cases strength was affected considerably by porosity. In the dolerite, strength was also affected by fissures (microcracks) which were formed in the parent rock by shearing and later accentuated by weathering. While test results show that porosity, density and sound velocity are not reliable indices of rock strength, these properties are useful in interpretation of strength test results. Index testing can be used to classify samples according to similar behavior and to recognize the influence of fissures.

Jan 1, 1986

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

By Noel C. Joughin

In making judgements on tolerable levels of risk in industry, and in all spheres of life, it needs to be understood that every action gives rise to risk. Without risk, nothing can be done. Without risk, no economy could be advanced. There is a strong tendency to emphasize the risk at work, but persons who are not working are exposed to a different set of risks. Often persons who are not working face greater risks than persons who are working. Simply, in being alive, one is exposed to the risk of an accident, the risk of contracting a disease, and an extremely diverse variety of other risks. According to the Health and Safety Executive of the UK, it is not possible to have a state of zero risk, because ?a state of zero risk does not exist?. Because zero risk is a physical impossibility, it is not possible to design for a state of zero risk in all engineering design. While the strategic target of achieving zero risk is laudable it does not provide any practical guidance to engineers as to what acceptable limits of risk should be. This causes a significant and real problem in the design for and the management of risk. Without meaningful guidelines, engineers, managers and the authorities often find themselves in disagreement. Thus, it has become essential to establish criteria for tolerable levels of risk and unacceptable levels of risk in order to design and manage engineering systems properly.

Jan 1, 2011

By AIME AIME

T HE appointment of Herbert Hoover to the portfolio of Commerce in the President's Cabinet is to engineers the fulfillment of a long deferred hope to have an engineer in high political office and is a matter of congratulation to us for three reasons; because he is a mining engineer who represents the highest type of idealistic engineering effort; because he is a past president of the Institute; and because he has probably a broader grasp of world problems than any other living engineer. Frank A. Vanderlip in the preface to his book "What Happened to Europe" tells of the many interviews he had with the most prominent men in Europe which were made possible for him by his eminence as a banker and by the courtesy of the American ambassadors. He cites by name such well known figures as Austin Chamberlain, Sir Auckland Geddes, Monsieur Delacroix, Monsieur Briand, Mr. Padkrewski, Mr. Venizelos, Colonel House, General Pershing, Mr. Baruch, and many others and says :

Jan 1, 1921

By Frank Sames, Brad Terhune

In many construction projects and in most quarrying operations drilling and blasting remains the only feasible method of loosening rock in the removal of rock or overburden, the development of the quarry and in the production process of crushed stone. Often, a blasting plan is required for the project or the quarry’s permit with primary concerns over safety and site security, and compliance with environmental regulations or standards. From this plan, a blasting program has to be developed considering the varying requirements of production, the advance of the mineral extraction and the environmental impact. The actual blast design requires a planning and optimization process. This optimization process is driven by the blasting technicians/engineers, project or mine management and often by community concerns. The blast design process comprises the selection of blast parameters, including the explosives, and the actual layout of the blast. Design tools and controls range from conventional methods based on established blasting practices to advanced design tools or computer models. Blast monitoring and evaluation can also range from empirical to advanced blast assessment. The data and information from each blast or a series of blasts can further be used in the optimization process. Its success depends upon recording the data, the timely transformation of the data to relevant information, and the development of process oriented knowledge. The elements of the blast design process are summarized and described with examples of state-of-the art engineering controls. The reporting and monitoring of individual blasts is discussed with respect to data management and information systems. A conceptual overview of the components and interfaces of a blasting program is given and discussed on the background of technical, management and community concerns.

Jan 1, 2004

REORGANIZING AMERICAN ENGINEERS There are in America approximately 500 engineers' organizations of various kinds, and yet it is estimated in many communities that 30 to 50. per cent. of the resident engineers are not members of any society of engineers. There is no enumeration of the engineers of the country, but estimates range from 100,000 to 300,000, the latter number probably including assistants, such as instrumentmen, draftsmen and inspectors, together with professional engineers. These local, state, regional and national organizations are for the most part independent and have no means for cooperation. Steps toward the improvement of these conditions are being taken in a number of localities and have already been taken in others. Many engineers are giving the matter serious attention. American Society of Civil-Engineers took an important action at the June meeting of its Board of Direction, by, authorizing the creation of a Committee on Development of Am. Soc. C. E. This action is now well known to all representatives on Engineering Council. Other Founder Societies axe reported to be considering similar action. Engineering Foundation, at its meeting on Sept. 12, adopted the following resolutions: Survey of Engineering Organizations BE IT RESOLVED: that the Engineering. Foundation is prepared, the four Founder Societies concurring, to devote its strength and its' income, so far as this may he required, to a study of existing engineering organizations, and from information thus developed to formulate a series of constructive recommendations which may he serviceable in guiding the further development of local and national engineering organizations in their relations to the profession of engineering, to the public and to each other, to the end that a foundation may he laid upon which to establish a broadly planned procedure, which, while recognizing and preserving all that has already been accomplished, shall increase the power of American engineers in upbuilding their profession and in the service they render to society; and RESOLVED: that in accepting the responsibility for such an undertaking, it will be the purpose of the Engineering Foundation to organize the proposed research along the broadest possible lines, to call to its aid highly qualified experts, and to avail itself of the help of agencies which may be willing to cooperate; and RESOLVED: that in proposing this research the Engineering Foundation has no desire or purpose to intrude upon the domain of individual organizations; that it does not propose to control the action of any individual or organization; nor to ask the acceptance of its conclusions; but that its purpose shall he to develop a possible procedure, or a series of such procedures, of such evident, merit that they will appeal to those who are likely to be most interested; it will do this in the belief that in so far as its work may justify the confidence of engineers and of engineering organizations, it will bear its own fruitage.

Jan 11, 1918

By J. Parke Channing

IT, HAS been my privilege to be Chairman of Engineering Council for very nearly three years, during which time Mr. A. D. Flinn, the. Secretary, and myself, have seen the organization develop until it is functioning smoothly and accomplishing what it can with the money at its disposal. The earliest attempt at what may be called an Engi¬neering Council, of which. I have any knowledge, was made six or seven years ago when the four Founder Societies each appointed two men, who occasionally met to discuss matters submitted to them which were of importance to, the, profession as a whole. I was one of the representatives of the American Institute of Mining Engineers.

Jan 1, 1920

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997

By A. P. E. Dirige

In order to maximize the recovery of ore and to save on costs in undercut mining, backfill of low cement content is used to fill the mined out excavations. This backfill mass is supported by a sillmat structure cast from cemented backfill of very high strength. The stability design of sillmats must be carefully studied to provide very effective, safe and economic mining operations. This paper presents a methodology and procedures for sillmat design based on three engineering modeling approaches: analytical, numerical and centrifuge modeling. Application of the design approach is demonstrated from a design study conducted for an underground gold mine, aimed at minimizing backfill binder content and at producing cost efficient paste fill recipes for sillmat construction. Application of the engineering design recommendations was projected to result in substantial annual cost savings to the mine operation.

May 1, 2007

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By T. W. Turk, S. A. Sass

The engineering design features of the Mercur Gold Project crushing, grinding, carbon-in-leach, bullion, reagent, and tailings disposal areas will be discussed in this paper. It presents a project overview and flowsheet along with selected design alternatives. During the engineering phase, major equipment and other features were selected to optimize design within site location and environmental constraints. The project team organization and procedures were adopted to accommodate multiple optimization studies while maintaining a tight engineering schedule.

Jan 1, 1985

By T. W. Turk

In May 1984, Davy McKee Corporation was awarded a contract for engineering design, procurement assistance, project management and startup services for two gold recovery plants? in the People's, Republic of China (PRC). The basic design of these two projects was to be accomplished by a combined effort of the Chinese and Davy McKee Corporation (DMC). The, design goals were to provide a state-of-the art plant while maintaining Chinese standards and design practices whenever possible. Chinese-manufactured equipment was to be used as much as possible. This paper discusses the project organization and procedures developed to accomplish the design goals, the process selection and design, and the selection and procurement of equipment outside of the PRC. Design development for grinding, leaching and carbon adsorption, and gold recovery are discussed in detail. The major goal of process selection and design was to provide common criteria for both plants. Equipment .sizing and selection was identical for carbon-in-leach adsorption, gold recovery, acid washing, and carboo regeneration for both plants. Of special importance is the design of the wastewater treatment system. Due to the cl0se proximity of a major population area, slurry discharging from these mines must be treated to meet drinking water standards. The process development and design of this system is also discussed in detail.

Jan 1, 1989

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By N. Duda, W. Koperska, S. Anufriiev, P. Stefaniak

In mineral processing plants ore extracted from mines is processed to obtain a concentrate with the highest possible concentration of this valuable product. It is a complicated multi-stage process. Usually, the first step is sieving the ore, which is typically done using vibrating mining screens. There is often only a limited number of these machines in the technological chain, which is why their continuous operation, and proper maintenance is crucial for the whole process. Predictive maintenance is the best strategy in this case because it allows for minimising the number and duration of unexpected stoppages. It consists of the prediction of future failures based on available real-time data, and predictive models built upon this data using, for example, machine learning techniques. In this paper we concentrate on feature generation for future predictive maintenance model development for a vibrating screen, based on an example of a KGHM ore processing facility in Polkowice-Sieroszowice. We focus on two types of measurements: bearings temperature and vibrational data. Based on the raw data, the process of more advanced feature engineering is described. By transforming the temperature data we calculate characteristics of bearing cooling and heating dynamics, while based on vibrational data, the aggregated characteristics of the vibrations are derived. Such features are calculated on a long-term basis, and then they are compared to the data related to vibrating screen maintenance to estimate their significance for the prediction of particular failures of the machine.

Sep 1, 2021

By AIME AIME

AN unusual interest in the question of orienting the young college man in the mineral industry was shown in a well-attended session* of the Engineering Education Committee on Monday afternoon. About seventy-five employers and educators of mining engineers were present and took part in the discussions.

Jan 1, 1929

L. C. UREn,* BerkelEy, Cal. (written discussion).—I heartily concur with Rlr. .Fobs concerning the need for advanced courses on various phases of Petroleum Engineering. I think that his criticism is probably true of most of the engineering schools that are specializing at all in Petroleum Engineering, that is, that most of their so-called graduate courses are not of graduate caliber but are merely more specialized aspects of undergraduate subjects. It would undoubtedly be to the advantage of the petroleum profession if more advanced work could be offered in a few of the leading engineering institutions so that there would be something substantial to offer graduate students wishing to return after a period of undergraduate work, for additional training. There is no doubt but that a better trained engineer, more useful to the oil industry, could be secured from schools offering such advanced training. The problem of adpting our instruction to fit the needs of engineers trained along other lines who wish, after completion of their undergraduate work, to enter thc petroleum engineering field, is a more difficult one. It has been my experience that such men are usually sadly deficient along certain lines and that they are really not prepared for the more advanced work in Petroleum Production Engineering until they have gone back over the work which they have missed in their undergraduate training. I note that Mr. Fohs suggests that other eastern and western colleges not now stressing Petrolelim Engineering, should be encouraged to take up advanced work of this character. With this, however, I cannot agree unless the institutions arc also prepared to offer a full sequence of undergraduate work on which the more advanced courses may be superimposed. Whether or not there is a need for additional engi-ncering colleges entering the petroleum engineering field is an open qucstion. I believe that we arc turning out enough petroleum engineers at the present time and that none of the six institutions now specializing in this field arc overcrowded. Morc-ovcr, they are fairly well distributed over the country, though there may be room for an additional school in the field in the eastcrn section of the United States. F. W. Padgett, Norman, Okla. (written tliscussion).—Assuming that the stnclcnt has the proper fundamentals, that is, general science and a knowledge of the technology of the industry, then the problem is: What courses should be offered from the graduate standpoint? (a) Course Work.—His knowledge of the technology of the industry can be extended advantagcously by means of one and two-hour courses, which consist in a more detailed survey of the various branches of the industry. (b) Lilerdure.—This work may, or may not, be connected directly with his research problem. The student should become familiar with methods of locating articles in the 1iterature; should also become familiar with all the important original

Jan 1, 1928

J. M. Wadsworth,' Okmulgee, Okla. (written discussion).—It seems to me that thc young man must first be absolutely sure that the work he has taken up is to his liking and then I would advise that he get into the practical end of it and learn as much about it as he can as fast as he can. For instance, in the refinery business the college man, graduated in chemical engineering, should ground himself by going through the various departments in a refinery and working in them until he is thoroughly familiar with the operating problems. In a short time he would be able to apply many things which appear in the abstract form in his college work and this would opcn up an opportunity for him to capitalize on them, promoting his own interest. I do not criticize the present-day college men as a class, but I have found that many of them come into your plant with the idea that mere possession of a diploma should insure rapid promotion; in a short time they are impatient and usually leave. We have found in employing men that the single attribute most difficult to find in them is a lot of energy and whole-hearted interest in the work at hand, and it seems to me that if a man combines these with a careful technical training he should be fairly well equipped to gamble on his future. They must learn that the biggest satisfaction to be gained in life is in their work. Procedure for Attaining Objective of Young Petroleum Engineer H. B. Fell,+ Ardmore, Okla. (written discussion).—Of course, the first thing to be ronsidered in any proposition is the ultimate objective that is desired to be attained. 1 presume that the desired objective of most of the young men graduating in petroleum engineering will be that of chief executive of one of the companies in the petroleum industry, or one of the allied industries, or to become an independent oil producer, or oil refiner, or possibly an oil distributor. The next phase then to be considered is the procedure which should most logically be followed to attain the objeckive of the indivitlual, since in these cases these young men will have been trained in a course in petroleum engineering and it would logically be presumed that the attainment of their objective should be through the operating end of the branch of the business with which they are connected. The operating end is, of course, the department of each branch of the business that develops the resources, or refines the products, or distributes the products, from which the profits are derived, and is a part of any business which is filled with enough interesting work to appease the desires of the most ambitious young men. In order to get the best possible training it would appear to me that the place for a young man to start after graduation would be at the bottom of that branch of the industry which he expects to follow. For example, if he is going in the producing end he can gct no better training than is secured by starting as a roustabout in the ficltl, where he romes in constant rontact with the character of work that is necessary

Jan 1, 1928

By H. C. George

At the annual meeting of the Institute in February, 1927, we had a comprehensive discussion of Petroleum Engineering Education. This discussion covered basic training and prerequisites, laboratories and equipment, graduate courses, availability of lecturers, geological engineering, petroleum production engineering, refinery engineering, transportation engineering and economics and management. However, there are several phases of petroleum engineering education, which many members of the Institute felt should be further discussed at this year's meeting. The first was expressed by me in a letter to those participating in the written discussion, from which I quote as follows: "We fell that the question of handling engineering graduates who enter the petroleum industry should be thoroughly discussed. "During the first five years after graduntion from college, how can these young men be best trained to be of the greatest service to the industry and at the same time do work which will be interesting and of a character which will make them feel that they are accomplishing something and making progress leading toward personal advancement?" Both the written and oral discussion would indicate three groups of opinion; first, those who advocate letting the young engineers go into the industry and take care of themselves without any supervision, direction, or guidance; second, those who advocate the taking of young engineers into the industry and letting them go through all the steps that any laborer or any other mian without a technical education would take, but with some supervision, and third, those who advocate that young cngineers should be given special training for several years after entering the industry. Of course all of these different groups are found in rnost of our industries. The Doherty training school of the Empire Gas & Fuel Co., finds its counterpart in the practice of the Gcneral Electric and Westing-house companies in the electrical industry and the Baldwin and Brooks Locomotive works in mechanical engineering.

Jan 1, 1928

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By W. B. Plank

THE figures on enrollment in the engineering schools of the United States and Canada indicate that the total number of students in these schools for the current year, 1949-50, is about 10% less than it was a year ago. This year, 226 - 533 undergraduates and graduate students are studying engineering in the United States and Canada as compared with. 249,913 students last year. These figures are taken from advance data in the Journal of Engineering Education for February 1950.

Jan 1, 1950