Search Documents

By Sun Ying, Zhang Jing, Li Qiuju

A new process of enrichment Cu in molten copper slag under electric field is presented in this article. The experiments were carried out in the laboratory on a kilogram scale. The mobility of copper slag was improved by the technique of carbon reduction. The effects of temperature, electric field strength and intermittent feeding speed were investigated on Cu migration. The results showed that the best experimental conditions were the temperature at 1523K, electric field strength was 1.5V•cm-1 and feeding rates was 15 g•(10min)-1. The copper content of the slag decreased below 0.6wt%. The process was compared to the traditional electric furnace process of slag cleaning, there was reduced the energy consumption and heat loss, and also harmful gas emissions such as SO2 and CO2, accompanied by improved the efficiency of slag cleaning.

Jan 1, 2016

By Samuel Filgueiras Rodrigues, Clodualdo Aranas Jr., Gedeon Silva Reis, Eden Santos Silva, Fulvio Siciliano

When austenite is deformed above the Ae3 temperature, partial amount of it transforms dynamically into ferrite by a displacive mechanism. After unloading, it retransforms back into the stable austenite by a diffusional process. This influences the rolling load which decreases under isothermal condition or does not increase with decreasing temperature as rapidly as expected under cooling. Plate rolling simulations under isothermal and continuous cooling conditions were carried out on a 0.09 wt.% Nb X-70 steel. Pass strains of 0.2 were employed together with interpass times of 10 s, and 30 s for the cooling conditions and 0.3 with interval of 10 s at 900 °C for the isothermal experiments; strain rate of 1 s-1 was used during the simulations. The mean-flow-stress (MFS`s) behavior of both conditions indicates that dynamic transformation and dynamic recrystallization were taking place during straining. The critical strains for the initiation of dynamic transformation fell around 0.06 while the critical strain for DRX was 0.12. It has been shown that ferrite is formed due to the applied deformation of roughing passes and increases its volume fraction throughout the finishing rolling stage. Under cooling conditions, the ferrite formation is also favored as the temperature approaches the Ae3 line. Such ferrite forms when the driving force for dynamic transformation is higher than the total free energy barrier preventing its formation. This obstacle consists of the free energy difference between austenite and ferrite as well as the lattice dilatation work and shear accommodation work. The addition of Nb retards the retransformation of the ferrite into austenite. Moreover, holding times after rolling increases the amount of austenite available for microstructure control on subsequent stages. The dynamic transformation (DT) mechanism can be used to design improved rolling schedules

Oct 1, 2019

By Messenger A. J, Miles J. G

A thermal neutron irradiation technique using a mCf neutron source has been developed and applied to thp.simultaneous determination of iron and aluminium (expressed as AI2O3) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt.While the determination of iron with this technique is based on the use of a NaI(TI) detector to monitor the characteristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the etermination of AI2O3 is based on the use of a second Nal(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the AI2O3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing.Dynamic trials of the technique, using 1500 kg samples of ore on a 460 mm-wide rubber conveyor belt moving at 1.7 m/min, have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% AI2O3. At the present stage of development, it is recommended that lump ore be crushed to a particle size of 6 mm before analysis.In addition to iron and AI2O3 determinations, measurements of total moisture content and bulk density are possible. The determination of Si02 is also feasible, but a separate fast neutron source (e.g., Am-Be) and a separate gamma ray detector are required.

Jan 1, 1980

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By Ingvar Ymén, Anders Sandc, Jan Rosenkranzc, Lisa Malma, Ann-Sofi Kindstedt Danielssonb

The understanding of particle surface properties is essential for the study and evaluation of froth flotation phenomena, particularly in the investigation of various chemical or reagent effects. Dynamic Vapor Sorption (DVS) is a method used for the analysis of surface properties of powders for instance in the pharmaceutical industry. To the knowledge of the authors, it has however not been used before in applications related to mineral processing. The DVS technique involves measurement of the water uptake of a relatively small amount of sample as a function of the relative humidity (% RH) in a temperature-controlled environment. The purpose of this work was to evaluate the method and investigate how it can complement existing techniques for surface characterization in mineral processing. Four samples (feed, CuPb concentrate, Cu concentrate and Pb concentrate) from the Cu – Pb flotation process in the Garpenberg concentrator, Sweden, were analyzed by DVS and the traditional capillary absorption technique (Washburn capillary rise). This enabled comparison between the two methods and evaluation of their respective advantages and disadvantages. Both methods give the expected ranking of the hydrophobicity for CuPb concentrate, Cu concentrate and Pb concentrate, but a discrepancy was observed for the feed. Washburn gave a value for the contact angle which was in the same range as for the CuPb concentrate, whereas DVS gave a value for the moisture uptake which was much higher than for the CuPb concentrate. Thus, DVS ranks all samples correctly, but with an unexpectedly high value for the feed whereas Washburn gives good ranking for three samples out of four. Potential reasons for the discrepancies are discussed.

Jan 1, 2018

By D. -A Tremblay

Dynamic wetting spread factors and interfacial heat transfer coefficients were determined for aluminum droplets solidifying on copper substrates, The spread factors were determined from the droplet geometries while the heat transfer coefficients were obtained by solving inverse heat conduction problems, 1-D and 2-D heat transfer models are presented and the results they provided are compared, For the latter, a sensitivity analysis was also performed to determine the influence of thermophysical properties and boundary conditions. Experiments were alternatively carried out with three different gaseous atmospheres and the dynamic wetting spread factors were correlated to the interfacial heat transfer coefficients.

Jan 1, 2005

By P. Morissette

Passive monitoring of support performance during rockbursts was conducted at three deep underground mines. A comprehensive database was constructed of 172 seismic events and the associated damage to support systems at 266 mine locations from January 2000 to September 2012. The majority of pertinent information was obtained through seismic system records and on-site field assessments. This work assesses the quality of collected information and evaluates the dynamic-load demand on support systems in seismically active mines.

Aug 1, 2013

By Carlos Maurício F. Vieira, Gabriel Oliveira Glória, Maycon Sidney Gomes de Camargo, Sergio Neves Monteiro, Fábio da Costa Garcia Filho, Maria Carolina Andrade Teixeira, Frederico M. Margem

The society is increasingly the concern about the ambiental impacts, and demand for eco-friendly materials. The composites reinforced with synthetic fibers are been replaced by composites reinforced with natural fibers because of the environmental advantages. Besides the environmental advantages, those fibers have economical and properties advantages, like the low density and cost. Composites with up to 30%of PALF fibers were tested. The analyzed parameters were the loss modulus, the storage modulus and the delta tangent. The test was conducted in the temperature interval from 25 to 195 °C in a DMA equipment operating at 1 Hz of frequency under a nitrogen flow. The results showed that the incorporation of continuous and aligned PALF fibers tends to increase the viscoelastic stiffness of the epoxy matrix. Contrasting this, minor changes occurred in both the glass transition temperature and the damping capacity of the structure as measured by the tan delta peaks.

Mar 1, 2018

By Lucas Barbosa de Souza Martins, Felipe Perissé Duarte Lopes, Nathalia Carneiro Garcia Rosa, Lucas Lopes da Costa, Sergio Neves Monteiro, Rubén Jesus Sanchez Rodriguez

"The fibers extracted from the stem of the banana plant are relatively stronger and have been used as reinforcement of polymer matrix composites. In addition to quasi-static mechanical properties, there is a need to characterize the dynamic behavior of banana fiber composites subjected to thermal and mechanical constraints. In this work, the temperature variation of the dynamicmechanical parameters of polyester composites incorporated with up 30% in volume of banana fibers were investigated by DMA tests. The storage and loss moduli as well as the tangent delta were measured from 20 to 200°C in a TA Instrument operated with the flexural mode at 1 Hz. The results showed that the incorporation of banana fibers tends to increase the viscoelastic stiffness of the polyester matrix. It was also observed changes in the T g and the structure dumping capacity of the composites with increasing fraction of banana fibers.IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times by our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber [1]. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites [2-7]. Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to C02 emissions responsible for global warming. Moreover, as compared to synthetics, lignocellulosic fibers present lower density and cost as well as reduced wear caused to the processing equipment. On the other hand, in terms of composite reinforcement, hydrophilic lignocellulosic fibers present drawbacks such as weak adhesion to hydrophobic polymeric matrices in addition to dimensional limitations and non-uniform properties."

Jan 1, 2011

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By P. Prusti

An air dense medium fluidised bed separator (ADMFBS) is the efficient process for dry beneficiation of coal. Magnetite powder is used as medium to make required pseudo-fluid density in the fluidised bed. The dynamics behavior of coal particle with reference to its position changes from ideal solution to pseudo-fluid condition in different bed densities depending on its shape, size and density. In this study, three set of projected areas of coal particles were taken. Each set contains four different shapes i.e., cubical, rectangular prism, spherical and triangular prism with different density starting from 1.3 to 1.8 gm/cc. It is observed that coal particles having density less than the bed density, floats in different positions in the dense medium fluidised bed. Higher projected area particles float in deeper height in comparison with smaller projected area. The difference in position of coal particles in the bed increases (nearly 1 to 4 cm) as the coal density approaches towards bed density irrespective of the different shapes. Different shapes of coal particles behave in different ways based on the operating parameters like bed density, coal density and projected area of coal particle. Empirical model equations are proposed to predict the position of coal particle of each shape in the air dense medium fluidised bed system. Keywords: ADMFBS, particle dynamics, projected area, shape

Sep 1, 2012

By D. O. Downing

"The 1990s saw enormous changes in the Canadian coal industry and the future promises to be no less turbulent. While the markets served by Canadian coal producers have changed and buying practices continue to evolve, the coal mining, or supply side, has also changed remarkably in response and now provides the basis for an interesting industry story.The dynamic situation in coal mining has led to some surprising outcomes and seemingly contradictory developments. This paper outlines the changes that have occurred, and which are still unfolding in Canadian coal mining, firstly, in terms of mining technology and productivity, secondly, in terms of corporate divestments, acquisitions and bankruptcies, and finally, in terms of resource development. The paper also outlines some plausible futures for the industry looking ahead."

Jan 1, 2002

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By N. B. Gray, A. E. Guerra, D. E. Morton

"The formation of splash in pyrometallurgical operations that involve the injection of gases into a liquid has been the subject of a number of studies over the last few decades. Given the complexity of the phenomena, there have been some advances in understanding the microscale formation of splash but the ability to accurately predict the amount and character of the splash formed is still in its infancy. First, the macroscale mechanisms for splash formation is very varied. Second, the timescales for splash formation are very small, usually less than 100 milliseconds, making experiments elucidating the formation of splash difficult and costly. Work at the GKW CRC has shown that the microscale mechanism of splash formation is primarily is due to the Kelvin-Helmholtz instability. Substantial progress has been made in understanding the behaviour of large bubbles in effecting splash formation and a simple model has been developed to estimate the behaviour of splash formed from a top submerged lance. Direct numerical computation of splash formation using the GKMAC codes developed at the Centre has been successful in simulating the impact of liquid drops onto a liquid bath.IntroductionInjection of gases into melts is used in the metallurgical industry to promote mixing to ensure acceptable heat and mass transfer rates, conveying solids for alloying, provide efficient contact for gas-melt reactions, and as a reactant. High gas injection rates bring about the formation of splash and slop. Extensive splash formation leads to loss of valuable product, creation of safety hazards, formation of accretion on refractory lining and exhaust ducts, and increased load on dust removal equipment. Many operators and researchers have claimed that splash formation is the limiting factor in many gas injected processes. The problems listed above lead to loss of production and increased maintenance, adding to the cost of processing base metals. Over the last five years, the GKW CRC has been studying the formation of splash from a number of sources. They include the impingment of drops on liquids[ l·2.31, slopping of bath liquidI4.51, breakup of gas bubbles at the liquid-gas interfacel61, shearing of liquids by gases[7·81, and impact of packets of fluids on solidsl81. Theoretically, the extreme deformation of fluid shape and the influence of surface tension makes the simulation of flow resulting from only a drop impacting on a liquid surface a very challenging computational fluid dynamics problem. Recently, we have been successful in simulating the formation of the Rayleigh jet resulting from a drop impact showing the effect of drop Froude number on the shape of the Rayleigh jet."

Jan 1, 1996

Dynamics of Three Phase Contact Line Motion in Liquid-Liquid-Solid Systems - Impact of Surface Roughness

Sep 13, 2010

I attended a funeral in West Monroe, Louisiana, for one of the best powder peddlers I’ve ever known. He started work in 1948 for Dixie Dynamite, a seismograph explosive distributor. His first job was as a truck driver, then magazine keeper and then sales re p re s e n t a t i v e . When Dixie Dynamite quit, he acted as an explosives sales agent for sometime before moving on to Kansas to be a sales rep for a distributor there. We called him the “ragin cajun” long before James Carville came on the national scene messing up things. While he was born in G e o rgia, he was a Cajun at heart. I don’t believe the old saying, “Build a better mousetrap and the world will beat a path to your door.” To me, the best products in the world need to be sold. Two examples of this are the Beta system for TV and the Apple Macintosh computers. Beta is the best system but VHS took over because the Beta people fell down on the selling job. Windows 98 is Macintosh ‘86 but again the engineers were not salesmen. Marion “Johnny” Johnson who was buried only about a half mile from his first magazine site proved that good selling is good citizenship. He could have sold any firstclass product, for he wouldn’t tolerate inferior items, and made a successful career of it, but he chose dynamite and the industry benefited from his talents.

Jan 1, 2004

We had a cold, gray winter here in Kansas City and I spent a lot of time watching out my den window at the squirrels and birds trying to get by in the lousy weather. I remember too well working in the cold, loading shots. I was frostbitten several times since I couldn’t tie in MS connectors with gloves on. Those old connectors had a piece of detonating cord on either end of a metal tube that held the delay and you tied them to the trunk lines with square knots. Doing this on a “warm” day in Alaska or Montana shooting ditch for a pipeline could be a frosty experience. Also remember how hard it was to connect up electric caps (detonators to you new guys) in the cold. Now I don’t want you to feel sorry for me ‘cause I suspect most of you younger fellows have also paid your dues in the cold and for that matter in the heat too. Wowee, the heat at the bottom of a Chicago dolomite quarry in August was enough to fry the brains of all that were there. Maybe that’s why the third deck of my brains doesn’t exist.

Jan 1, 2004

By Susanne Hahn

The Siemens VAI software model DynaPhase calculates thermodynamic properties depending on the chemical analysis of steel. It can be used online together with Siemens VAI’s secondary cooling model SIMETAL Dynacs 3D which is a unique feature. Offline it can be used to investigate the thermodynamic properties of steel grades and therefore supports the development of new grades. The core of DynaPhase is a substitutional solution model for the Gibbs free energy to calculate multi-component phase diagrams. The parameters of this model are determined by employing the CALPHAD approach. This model is combined with a microsegregation model to account for the interdendritic solidification process. New DSC (differential scanning calometry) measurements of the department of metallurgy of the Mining University of Leoben have been used to improve the DynaPhase database for high Al or Si concentrations. By comparing this experimental data to calculations it has been found that some of the widely used commercial software tools do not describe the ternary system FeAlC for high aluminum concentration correctly. In this paper we will show how thermal properties of high Al grades change with the optimized database and what impact this has on the secondary cooling of continuous casting, e.g. how the solidus point shifts on the strand. Moreover we will show that the online use of DynaPhase has many advantages for the production. Since DynaPhase uses the actual chemical analysis of the steel grade and not just concentration ranges or averaged concentrations it is possible to optimize the cooling strategy during casting for the actual chemical analysis of the actual heat.

Jul 30, 2018

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

DynoMiner APS Delivery Systems Overview ? New Design of DynoMiner APS-M2 ? Stand alone or attach to Cargo type 10,000 lb (4536 kg) emulsion bins. ? Hose reel w/200-ft (61-m) by 1-inch I.D (25-mm) hose capacity, power rewind. ? Increased water and trace capacity. ? Hose reel and gassing offered as options. ? New Flow Meter ? DN-100: aluminum body, UHMWPE rotors. ? Will be offered as an option. ? APS Nomenclature ? Proposed changes ? DynoMiner APS and APS-M1 to become DynoMiner APS Drifter ? DynoMiner APS-M2 to become DynoMiner APS Stoper. ? Both to have optional gassing / flow metering.

May 1, 2004