Search Documents

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

The adoption of new technologies is accompanied by risks that the stakeholders will wish to understand and minimise. The process of developing a dynamic simulation and the plant it will be used in provides a discipline and attention to detail that highlights and provides an opportunity to mitigate risks that will exist in a production environment. The simulations will enable investigation of what the outcome of process failures will be and the impact maintenance. Enumerating this information will enable designs to be optimised and operating and control strategies to be tested.The success of new technology is dependent on the operators and their understanding of it and the machines that use it. In this context dynamic simulations can provide training and experience without risk to personnel, equipment or production. This experience will include situations that would not be induced in a production plant for training purposes. This paper outlines a generic template for a dynamic simulation that can be used to evaluate the introduction of an emerging technology into an operating environment. It includes process flows and surge capacity, breakdown and maintenance, operator interactions and availability, push and pull production scheduling and system control.

Sep 26, 2011

By P Navarra, R Kuhne

Dynamic simulation (discrete event simulation) is the preferred methodology to evaluate the impact of dynamic aspects of processing plants on the overall plant capacity. This tool can be used to: identify bottlenecks in the plant,justify upgrade and expansion projects by evaluating their impact, oroptimise maintenance and operating practices without disrupting the operation. Iron Ore Company of Canada's (IOC) pelletising plant is a complex operation because of multiple products, varying equipment capacity and shifting bottlenecks. Furthermore, with extensive capital requirements for projects and long lead times, a high level of confidence in project outcome is required. Therefore, a model of IOC's pelletising plant in Labrador City was constructed in 2007 by a joint IOC and Hatch team. The model includes both operational and metallurgical aspects in order to better capture the complexity of IOC operation. In this paper, the justification, boundaries, and functionality of the model are described. A comparison of simulation results to historical plant operation is given. It is observed that projects have interactions and that the benefits of combined projects are not equal to the combined benefits of the individual projects. Projects can have synergies that result in greater benefits when combined or can have overlapping benefits that result in lower benefits when combined. The power of the proposed modeling exercise lies in the ability to assess the impact of projects on overall performance.

Jan 1, 2009

Dynamic Simulation of an Alumina Refinery

Sep 13, 2010

By C. Bazin

Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action to correct the problem. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality leading to a less efficient grinding operation. A dynamic simulator is used to assess rules for the diagnosis of hydrocyclone faults from the trends produced by sensors.

Jan 1, 2009

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By Pate W. T

This paper describes the development of a dynamic flowsheet simulator for comminution operations. Object oriented software design allows the handling of multiple ore types, blended into multicomponent feed streams. Software objects have been c

Jan 1, 1998

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

By S. S. Gajin

The paper deals with parametric vibrations of an axially loaded pile. The dynamic model is derived by means of Hamilton's principle and reduced to a partial differen­tial equation with variable coefficients and corresponding initial boundary conditions, taking into account the influence of the axial force. By means of Galerkin's method, the partial equation is further reduced to a Matheu-Hill's matrix partial differential equation of the second order. Since the problem of the dynamic stabili­ty has been expressed only for standing piles, the paper analyses in detail two stan­ding piles, one which is restreined, whereas the other is hinged at the toe. In both cases it is assumed that head horisontal displacement is prevented. Using Ruunge-Kutt's method, a computer analysis in the time domain is given for the characteristic parameters and possible boundary conditions. The paper analyses the stationariness of the process, as well as the dependance of the critical excitation frequency upon the pile parameters. The results have been illustrated by respective diagrams.

Jan 1, 1989

By R. Raghavaraju

Estimation of the dynamic stress field in terms of its amplitude and decay around a blast hole is a key input parameter in all numerical modeling and blast prediction exercises. However, there is very limited information available in literature on these critical parameters, which would be considered essential in any blast modeling exercise. A laboratory-scale experimental study has been carried out in two different rock types to study at very close range the stress wave decay from a blast hole at distances ranging from 3 to 10 borehole radii. The single–hole blasting experiments employed a centrally located detonating cord (5.3 g/m) in 6 mm(1/4 inch) and 10 mm (3/8 inch) boreholes. The coupling medium employed was air and water, in addition to using a thin-walled copper tube in intimate contact with borehole wall to prevent of penetration of explosion gases into the emerging cracks. The paper describes the nature (amplitude and decay) of the transmitted shock pressure and their evolution in the two rock types for these various experimental conditions, which are present to varying degrees in all blasting operations.

Jan 1, 2014

By U. Singh, E. T. Brown, J. Coxon

The rapid fracturing and deformation that occurs around excavations during rock bursts demand that support and reinforcement systems have both deformability and damping capabilities. The energy demand and supply approach currently used in design is considered to be too simplified to represent adequately the rock burst process and the support and reinforcement system requirements. Momentum change may be a necessary second criterion for the analysis of dynamic loading situations. At the St Ives Gold Mining Company, DE plates made from conveyor belt rubber, and dynamic cables with sliding anchors have been developed and used to improve the dynamic performance of support and reinforcement systems. La fracturation rapide et la déformation qui se produisent autour des excavations lors de coups de terrain demandent que les systèmes d’armature et de support soient déformables et aient une capacité d’amortissement. L’approche basée sur l’énergie actuellement utilisée pour la conception est considérée être trop simplificatrice pour représenter adéquatement les coups de terrain et les paramètres de conception des systèmes d’armature et de support requis. Le changement de quantité de mouvement pourrait être un second critère nécessaire pour l’analyse des cas de charge dynamnique. St Ives Gold Mining Company a développé et utilisé des plaques « DE » constituées de caoutchouc de courroie de convoyeur et des câbles dynamiques avec ancrage coulissant afin d’améliorer la performance dynamique des systèmes d’armature et de support. Die ploetzliche Rissbildung und Verformung, die sich in Baugruben waehrend eines Felseinbruchs ereignet, verlangt Stuetz- und Verstaerkungssysteme, welche verformbare und mildernde Eigenschaften aufweisen. Die derzeitlich gebraeuchliche Methode den Entwurf auf den Energiebedarf und dessen Abdeckung zu basieren, wird als eine unannehmbare Vereinfachung betrachtet, da sie den Felseinbruch und die benoetigten Unterstuetzungs– und Verstaerkungssysteme unzulaenglich darstellt. Die Aenderung der Umstaende kann einen zweiten Ansatz fuer die Analyse der Lastsituation erforderlich machen. Die St.Ives Gold Mining Company hat DE Platten aus Foerderband-Gummi und elastischen Kabeln mit verschiebbaren Verankerung entwickelt und dazu verwendet, die dynamische Kapazitaet der Unterstuetzungs- und Verstaerkungssysteme zu verbessern.

Jan 1, 2003

By P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, all carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine fires. This paper describes a method of measuring the conductor temperature of mine trailing cables during normal operation. The temperature is measured using a 50/125 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

Jan 1, 1998

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

By A G. Thompson, E Villaescusa, A De Zoysa, J R Player

Ground support performance is critical to the safe and economical extraction of ore. This is particularly important for mass mining extractions at great depth, which are currently being considered by a large number of mining companies worldwide. As the in situ stresses concentrate around critical excavations, failure occurs at the excavation boundaries and ground support is required for the excavations to remain safe and accessible for their intended lifespan. Ground support consists of reinforcing elements that are installed within the rock mass to modify its internal behaviour (generally to within one excavation radius) and surface support elements that are installed at the exposed boundaries to retain the failed pieces of rock. For surface support to be effective, the loadings need to be transferred to the reinforcing elements; however, the combined performance of rock bolts and mesh is poorly understood in terms of the energy dissipation capacity available for a typical ground support scheme implemented at most mass mining operations.Over the last 15 years or so, a large number of large-scale laboratory experiments have been completed at the Western Australian School of Mines (WASM) Dynamic Test Facility for reinforcement systems and surface support systems loaded separately. The objective of more recent testing has been to establish the combined energy dissipation capacity of typical and enhanced reinforcement systems combined with mesh surface support. Total energy dissipation has been separated into energy dissipation attributable to the reinforcement and to the mesh. The results of the tests are presented and compared with the existing WASM design demand and capacity guidelines.CITATION:Villaescusa, E, De Zoysa, A, Player, J R and Thompson, A G, 2016. Dynamic testing of combined rock bolt and mesh schemes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 789–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A rough simulated borehole has been developed for the installation and dynamic testing of rock bolts a the WASM Dynamic Test Facility. The rough simulated borehole is used for rock bolts that are sensitive to equipment installation technique or borehole geometry (particularly friction rock stabilisers and resin encapsulated bolts). An extensive axial test program has quantified a difference between the static and dynamic capacity (kN/m of embedment) for friction rock stabilisers once sliding starts. The 47mm split tube bolt has a 50% reduction in embedment capacity (but with significant variation) dissipating 2.7kJ/100mm of sliding per meter of embedment, and the Omega (inflatable) bolt had a 70% reduction in embedment capacity dissipating 6.2kJ/100mm of sliding per meter of embedment. The Omega bolt dynamic capacity remainder at least equivalent to the split tube bolt static capacity.

May 1, 2009

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995