Search Documents

By K. A. Grace

K.A. Grace's article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed.) Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing.

Jan 8, 1985

By D. F. Ball, P. R. Dawson, J. T. Fitton

Report of discussion at December, 1970, IMM general meeting (Chairman: M. J. Cahalan, President) and contributed remarks on the paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C189-96, plus the authors' replies. Contributors included Cohen E., Hope B., Wasse D.G., Shakespeare A.G., Burwood D.S., Jones H.A., Dartnell J., Carter G.C., Henderson T.A., Relf G. and Clark S.W.

Dec 1, 1971

By S. Y. Ezz

Report of discussion at February, 1971, IMM general meeting (Chairman : M. J. Cahalan, President) of a paper published in Transactions/ Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C226-C233 with contributions by Wild R. and Astier J. on fluidised bed reduction of iron ore fines

Dec 1, 1971

By B. W. Hester

Report of discussion at January, 1971, general meeting (Chairman: M. J. Cahalan, President) of the paper published in Transactions/Section B (Applied Earth Science), vol. 79, May, 1970, pp. B60-B67, and contributed remarks. Comments were made by Taylor J.T.M., James C.H., Lethbridge R.F. and Heath K.C.G.

Dec 1, 1971

By A. W. Fletcher

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J, Cahalan President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, December, 1970, pp. C247-52, and contributed remarks. Contributions are included from: Cahalan M.J., giving figures related to leaching Cu from pyrite at Rio Tinto 1880-1910; Noakes F.D.L.; Embling P.M.K.; Bradshaw A.V.; Le Roux N.W.; Kelly D.P.; and Tuovinen O.H. Questions were raised regarding impurity removal, effects of light and ultraviolet light on the bacteria, the economics of solvent extraction and the possibilities for other organisms or other metals

Dec 1, 1971

By J. R. Hammond, I. C. Herbert

Report of discussion at October, 1970, IMM general meeting (Chairman: M. J. Cahalan, President) and contributed remarks on the paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, June, 1970, pp. C128-36 and introduced by I.C. Herbert. Contributors were von Struve G., on the application of balling discs and the use of basic additives; Young P.A., asking for details of the drying, grinding, balling, induration and specification testing equipment and processes; Davison J. on pellet swelling properties and Carter G.C. on disc operation, refractories and green ball properties.

Dec 1, 1971

By S. V. Shiraishi, H. B. Bell

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J. Cahalan, President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, June, 1970, pp. C120-C127, with a contribution by Wright P.A. on the miscibility gap

Dec 1, 1971

C. W. MERRILL*—Mr. Hughes' paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably. a matter of vital interest. Your Chairman, Mr. Romanowitz, in his introduction, referred to the fact that I had been a member of the United States delegations to the three meetings of the International Tin Study Group. Some comments on the Group's objectives and deliberations may be of interest. When it appeared that the International Tin Committee, the prewar producer's cartel, might soon revive its operations and extend its control agreement beyond the expiration date of Dec. 31, 1946, the United States Government became interested in some kind of an international trade organization concerned with tin which would give the consumers' interest equal representation with the producers' interests. An international meeting was called in London in October 1946 to consider this problem. I did not attend that meeting hut the result of the meeting was the organization of the International 'Tin Study Group which

Jan 1, 1950

R. B. BRINSMADE, Ixmiquilpan, Hgo, Mexico* (written discussion). As the discussion of Mr. Graton's paper by Messrs. Norris, Patterson, and Crane has been from the standpoint of the mineral land-value owners, a few remarks in the interest of the "under dog"-the average taxpayer and citizen-may prove timely. In my discussion of Doctor Raymond's Paper1 and of the papers of Messrs. Gibson2 and Godson, 3 have endeavored to demonstrate, from both political economy and history, that our existing system of unrestricted private ownership of land is incompatible with equality of economic opportunity and, therefore, subversive of our democratic political institutions. In Mr. Graton's paper, the same land problem is important, though camouflaged by the failure of the Federal income tax laws to distinguish between land and capital, in the requirements for valuation, or between earned and unearned incomes in the levying of taxes. I disagree with Mr. Graton's statement, on p. 2967, as follows: The immense majority of mining ventures are failures. A multitude of disappointments is relieved by occasional success. Were it not for the chance of great rewards, all the vitally necessary but mainly unremunerative work of exploration would not be undertaken. In contrast with nearly all other fields of endeavor, it is altogether unlikely that, on the whole, the gains in the successful mining ventures suffice to offset the losses in the unsuccessful.

Jan 3, 1920

Lake Superior Meeting . PAGE Gathmann, Emil.-Casting and Molding Steel Ingots. Discussed by J. W. Richards.. 2 McCaffery, R. S.-The Acid Bessemer Process. Discussed by Bradley Stoughton, J. W. Richards 3 Elliott, S. R.-Athens System of Mining. Discussed by F. W. Sperr, Lucien Eaton 4 Mercer, H. T. and Paulson, A. C.-Handling and Treatment of Rock-drill Steel at Copper Range Mines. Discussed by Harrison Souder, H. T. Mercer, W. H. Schacht, C. M. Haight 5 Hayden, J. E. and Eaton, Lucien.-Building Reinforced-concrete Shaft Houses. Discussed by William Kelly, T. L. Condron, Lucien Eaton 7 Eaton, Lucien.-Mechanical Ventilation at Lake Mine. Discussed by C. A. Mitke 8 Schacht, W. H.-Steam Regenerators Reduce Coal Consumption. Discussed by 0. P. Hood, W. H. Schacht ? 9 Linton, Robert.-Standardizing at North Butte Mining Co. Discussed by Grant H. Tod, C. A. Mitke 10 Smith, H. DeWitt and Sirdevan, W. H.-Mining Methods and Costs at United Verde Mine. Discussed by C. A. Mitke 12 Davy, Myron A.-Reflecting Microscope for the Mining Engineer. Discussed by C. P. Berkey, W. A. Rukeyser 14 , Norden, J. A. and Willson, A. R.-Hoisting Equipment at Utah-Apex Mining Co. Discussed by E. M. Norris 17 Aldrich, H. R.-The Dip Needle in Stratigraphy. Discussed by H. R. Aldrich, W. 0. Hotchkiss, Carl Zapffe, E. A. Kronquist 18

Jan 1, 1921

By U. N. Bhrany, N. Arbiter

F. C. Bond (Consulting Engineer, Processing Machin-Dept., AllisChalmers Manufacturing Co., Milwaukee) This is a very comprehensive paper. It deals with 1) size distribution functions, 2) energy-particle size relationships, and 3) criteria for grinding efficiency. The method of analysis used consists of tracing the increase and decrease of successive Tyler scale screen fractions as grinding progresses. The treatment is based upon the assumption that the work done in grinding is concentrated entirely upon the coarse size fractions in the mill. It is postulated that when a feed consisting entirely of particles of one size fraction is batch ground that finer fractions increase at a constant rate as grinding progresses, until finally each in turn begins to be ground and to decrease in amount. It is shown that under these conditions the empirical Gates-Gaudin-Schuhmann log-log size distribution plot can be logically explained. It is difficult to imagine any condition of ball mill operation, or any probability analysis, which would result in no grinding contacts on the finer particles present. However, the authors' postulate must be accepted if their conclusions are to be sustained. They conclude that the equation expressing the for mation rate of each size fraction can be resolved into the G.-G.-S. size distribution equation, and that the curvilinear portion of the log-logsize distribution line represents the only particle sizes which are being ground as well as produced. The author's statement that the G.-G.-S. Eq. 4 applies only to the finer portion of the size distribution while the Rosin-Rammler Eq. 6 applies over the whole size distribution range certainly supports the view that an exponential equation of the Rosin-Rammler type corresponds more closely to actual size distribution than does the power law G.-G.-S. equation. However, the G.-G.-S. equation is used to derive Eq. 8 and Eq. 9, which state that the energy required to grind a ton through a particular mesh varies inversely as the particle size to the exponent -a , whic h is the slope of the extended G.-G.-S straight line. This is stated to apply to both batch and continuous grinding. The G.-G.-S. slope exponent thus becomes very important in all crushing and grinding analyses by this method. The authors include some data which can be used to test their conclusions, as described below: We will consider grinding a feed composed of 14 mesh (1190u) to -200 mesh (74u). The average of 17 Allis-Chalmers grindability tests on quartz gives a work index (Wi) of 12.77. The -200 mesh product should have 80 pct passing 41.6u or P = 41.6. The equivalent 80 pct passing size of the 14 mesh feed particles is considered to be the particle diameter, as is true for spherical particles. Thus F is 1190u. In the work index equation 10 wi 10 wi 127.7 127.7 P f 41.6 1190 = 16.1 kw-hrperton. In Table I the ball mill exponent for quartz is 1.0 and from Eqs. 9 and 10: w=kw-hr/ton =Constan/(do/di) = 16.1 ton so that (1190) Constant/ Constant and the Constant equals 259. The tons per horsepower-hour value is 0.0464, in agreement with Table IV. The exponents for other minerals are listed in Tabl e 11. In Table IIA, the kilowatt hours per ton required to grind these minerals between the same sizes as the quartz, both by the authors' method and the work index equation, are listed. According to the authors kw-hrperton = 259/(16.1)".

Jan 1, 1961

By J. L. Gillson

Joseph H. Birman (Chairman, Dept. of Geolcgy, Occidental College, Los Angeles, Calif.) Many thanks to J. L. Gillson for so comprehensive a survey of the titanium sand deposits of the world. Over the past two years, the writer studied rather carefully some of the Cretaceous ilmenite deposits in New Mexico and Colorado, including the Sanostee deposit shown in Gillson' s map, Fig. 6. The deposits were geologically mapped and sampled, surveyed by magnetometer, and the Sanostee deposit was drilled. Moat of the genetic interpretations made by Gillson concerning the recent sedimentary ilmenites can be clearly read in the Cre-taceous deposits in New Mexico. The deposits are in marine regressive members of the Mesaverde group. The deposits trend within a few degrees of N 55° W and persistence of this trend through both distance and time (the deposits are in different members of the Mesaverde group) implies that the deposits are offshore bar accumulations. Heavy mineral content ranges from about 10 pct to more than 50 pet. Thicknesses are from 4 ft to as much as 20 ft, widths range from 150 to 600 ft, and lengths range from a few thousand feet to a few miles. All are locally or completely overlain by carbonaceous shale and thin coal. The deposits are strongly altered, and from X-ray diffraction the principal titanium alteration product appears to be anatase. Drilling of the Sanostee deposit shows that the alteration is not related to the present erosion surface but took place at the site of deposition and before burial by the overlying sediments. Iron oxide derived from the alteration cements the grains and is the chief coloring agent in the immediately overlying shales. In the Sanostee deposit, there is virtually no feldspar, the gangue mineral being almost exclusively quartz. Sorting is excellent, but the quartz grains are subangular to angular. Petrographic examination reveals that the angularity is not due to overgrowths. Therefore, short distance transport is implied. The mineralogical composition suggests a low relief granitic terrane as the source area. Feldspar may have been decomposed by weathering at the source, but an alternative preferred by the writer is that each of the deposits represents a long-term concentration site (for example a large sand bar) which was continually being deprived of light minerals by wave action and selective transport. Feldspar may have been mechanically reduced in size more quickly than the quartz, and thus its rate of removal may have exceeded that of quartz. Concentration of heavy minerals would thus occur until the marine regression removed the zone of maximum wave energy from the site. Chemical alteration would then become the most important process until burial by encroaching swamp deposits.

Jan 1, 1961

By R. F. Shurtz

R. Duval (Mining Engineer, Ancien eleve de PEcole Polytechnique, Paris, France) I do not agree with the Eq. 3, reading: m =1/100- [(0.214x30.4) + (0.7B6 x0.00)] =6.5pct CaO If 0.214 and0.786 were proportions by weight, the equation would represent the well known mixtures law of the conventional arithmetics and 6. 5 pct CaO would be the correct average content. But it is not the case as the author states: "In samples consisting of single grains of mineral, those grains must, as already mentioned, be either of dolomite or magnesite. Since 78.6 pct of the deposit consists of magnesite and 21.4 pct of dolomite (excluding for present purpose the presence of other minerals), for any single grains picked at random the probability will be 0.214 that is it dolomite and0.786 that is it magnesite. In 1000 such samples the expected numbers of dolomite and mapesite grains will be 214 and 786 respectively." 0.214 and 0.786 would be proportions by weigbt under the necessary condition that all grains of dole mite and magnesite should have an identical weight. Obviously it is not the case, as the specific gravities are not the same for mapesite and dolomite and the volumes of the grains are different. Furthermore, because of these differences the conditions for a random sampling are not fulfilled and we are not authorized to state that the probabilities are, respectively, 0.214 and 0.786. The author however makes a simple application of Eq. 1: M = 1/n— ? fi x i . n Should we deduce that this relation is wrohg? Not at all, but when applying Eq. 1 you must not overlook what it actually. means. Eq. 1 gives a definition of the arithmetic mean of a total of n observed values Xi and nothing else. But the average conteht of a deposit has not the same significance. It is the ratio between the weight of concerned mineral in the deposit and the total weight of the deposit. As from 1000 particles the 214 of dolomite and the 786 of magnesite have not the same weight, the two definitions do not concur, and when applying Eq. 1 the result is an arithmetic mean of figures which has no connection with what is named average contentof a deposit. The situation is similar to the calculation of an average velocity. If a car travels a first mile over at 30 miles per hr and a second mile over at 60 miles per hr, when applying formula 1 you find as average velocity for the 2 miles: 30+60 ------- - 45 miles per hour. Many people calculate in this way and they do not realize that a mistake is involved. In fact the definition of he average velocity for the 2 miles is the quotient of the distance of 2 miles by the time (in hours) necessary for 2 miles travel, i.e.: 2 ---------- = 40 miles per hr. 1 + 1 30 60 In other words, the average volocity wanted is not the arithmetic but the harmonic average of the two velocities. The above mentioned bias in the calculation of the average contents of deposits is frequent, even in the assessments made by experienced engineers and is independant of what is named the sampling error. In order to supress the bias and to be able to use Eq. 1, you must apply a correction. An example on the subject can be found in an article by Duval et al. in the January 1955 issue of the ''Annales des Mines" (French), page 19. R. F. Schurtz (Author's Reply) Mr. Duval's position is quite correct. The proportions shown for dolomite and magnesite., respectively, of 0.214 and 0.786 are, in fact, proportions by weight uncorrected for specific gravity. In our day to day operation of producing magnesite from these mines at a very substantial rate, we do not normally make corrections for the difference between the specific gravity of dolomite and that of magnesite. If these corrections are made in Eq. 3 as shown in my article, then the numbers of grains turn out to be in proportions of 0.226 dolomite and 0.774 mapesite instead of the values actually shown in the equation. For the purposes of our work, and in view of the inherently low accuracy of the data, this correction was not deemed worthwhile making.

Jan 1, 1961

By Rudolph G. Wuerker

Charles T. Holland (Head, Dept. of Mining Engineeri*, Virginia Polytechnical Inst., Blacksburg, Va.) Mr. Wuerker has presented a very interesting discussion of the use of triaxial test methods for investigating the strength properties of rocks. Such methods, no doubt, eventually will develop considerable information of interest to those concerned with the design of mine layouts, particularly in the field of pillar design. From his discussion of my recent article, "Cause and Occurrence of Coal Mine Bumps" (Holland Mining Engineering 1958, p. 933-1002), it is evident that in one place at least I did not make my meaning clear to him and perhaps others. To clear the matter up I think it best to quote from the article, somewhat more fully than did Mr. Wuerker, as follows: "4) In actual operations — because rocksare not perfectly elastic, homogeneous, nor isotropic and because local yield does occur — the maximum stress as demonstrated by Phillips (Ref. 22, pp. 64, 65) and indicated by much experience in mining, does not occur at the walls of the opening but at a short distance inside the pillar. Furthermore, the maximum stress does not reach as great a value as theoretical considerations and laboratory experimental methods indicate.* Actual distance inside the pillar, measured from the wall, at which the maximum stress exists, has not been determined. Observations in many mines, however, indicate that this distance could have a mini-value of one to six or eight times the bed thickness and that it is probably affected by width and height of the opening, depth of cover, and relative values of the elasticity and plasticity of materials comprising the roof, floor, and coal seam. The actual value of the stress produced probably lies between the theoretical maximum and the average stress concentration that would be produced if the weight of the strata above the unsupported opening were evenly distributed over the pillars for a distance equal to the opening width." The footnote reference in the above quotation referred to the following: "*For example, the Pocahontas No. 4 coal bed in southern West Virginia is mined under cover up to 1800 ft thick. Development openings are driven 18 to 20 ft wide, and the bed is about 6 ft thick. According to the work of Panek, the tangential wall stress at mid-bed height under these conditions would reach values between 4000 and 5000 psi. Actual tests of 3-in. cubes of this coal show its compressive strength would be much less than this, perhaps as low as 400 psi. Yet the pillars usually show no evidence of failure in these headings. In this same bed at a depth of 800 ft, the author has seen an opening 225 ft between supports lying between two old groves approximately 1100 ft apart. According to the theoretical considerations, the stress in the pillar walls would have been about 18,000 psi, yet the pillar showed little or no evidence of weight. In view of these observations, it is clear that the wall stress does not attain the maximum values indicated by theory." (Underlining added to original wording.) By referring to Fig. 2A of my paper it will be noted that theoretically the maximum pillar stress would occur at the pillar wall, i.e., at the passageway surface of the pillar. Obviously this cannot be correct in the cases of stress ranging from 4000 to 18000 psi since the coal at the surface of the pillar is under no constraint and cannot have a strength much greater than 400 or 500 psi. Hence, my conclusion that the maximum stress does not occur at the wall but back in the pillar some distance from the wall. Since these stresses are pushed back in the pillar from the wall, it is also obvious that the loads transferred to the pillar from the opening will be spread over a greater area and hence Pillar stresses will not rise to the values postulated by theory and photoelastic experiment. Further since to visual inspection the coal along the pillar wall did not appear to be failed the conclusion was reached that the stress shift was caused by local elastic or plastic yield and by difference in the elastic modulus of the rocks composing the mine floor, mine roof, and coal bed. Later on under the heading "Strength of Mine Pillars" (pages 1000-1002) the effects of constraint is briefly described. Also a formula taking into account constraint is developed relating pillar strength to the uniaxial strength of coal and the L/T ratio of the pillar. Since my paper was written, reports of experiments conducted in South Africa (Denkhaus, et. al., 1959), in Sweden (Hast 19581, and in Canada (McInnes, et.al., 1959) reveal that the conclusion expressed relative to the existence of a low stress area existing around the edges of pillars and solid faces as described above is generally correct. But it seems possible that where the wall stress developed is less than the unconfined strength of the rock composing the pillar and where the roof, floor, and pillar

Jan 1, 1961

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn't "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By Bernardo Martins Braga

O curto-circuito é um dos componentes dos modelos de compartimentos utilizados na análise das curvas de Distribuição de Tempos de Residência (DTR) de distribuidores para lingotamento contínuo. Foram identificados na literatura, no entanto, diversos exemplos de seu emprego incorreto. O presente trabalho discute a interpretação física do curto-circuito, as formas de sua quantificação e as consequências nocivas de sua presença sobre a limpidez do aço e o controle da temperatura do aço no molde. Mostra-se que o método de cálculo dos parâmetros dos modelos de compartimentos deve ser alterado caso haja curto-circuito no distribuidor. É constatado que o curto-circuito deve ser evitado durante o projeto de distribuidores destinados à fabricação de aços limpos devido ao risco de perdas metálicas por macroinclusões.

Aug 16, 2017

By Edward A. Metz, R. Larry Grayson, Douglas F. Scott

We describe inconsistencies in disease and illness reporting in U.S. mining, identify under-reporting of disease and illness in U.S. mining, and summarize selected disease and illness in U.S. mining from 1983 through 2001. Methods: We summarized information on mining-related disease and illness data for the years 1983-2001 from the Mining Safety and Health Administration database (MSHA). Results: Discrepancies exist in types of information collected by the Centers for Disease and Control, the National Institute for Occupational Safety and Health, and the Mining Safety and Health Admin¬istration database. Several factors, including a worker's fear of losing his or her job, health insurance, or other job-related benefits contribute to under-reporting of disease and illness information in the US mining industry. Conclusions: Since 1997, both number of workers employed in mining and disease and illness rates have decreased; however, the highest disease and illness rates in mining continue to be coal worker's pneumoconiosis and hearing loss.

By Edinson Aponte

En la mina Yauliyacu (Huarochirí, Lima), de una profundidad aproximada de 1500 metros, existe un problema de sismicidad inducida por el minado, que puede derivar en desprendimientos o estallidos de rocas que afecten directamente a los trabajadores, equipos y a la infraestructura de la mina. Gracias al sistema microsísmico de monitoreo en tiempo real con el que cuenta esta unidad, se realizó un análisis del registro de estos eventos durante el segundo semestre del 2017 para identificar los niveles afectados o de mayor susceptibilidad a la manifestación de estallidos de rocas. A partir de ello, con el software Seis VisLite, se pudo hacer la zonificación microsísmica para la veta M. Los parámetros geomecánicos del macizo rocoso, con predominancia de arenisca silicificada, se introdujeron en el software Phase2 v.5.0 y se analizó el comportamiento de la redistribución de los esfuerzos principales en aberturas subterráneas en forma de herradura de la mina Yauliyacu, con otro tipo de abertura propuesta en la presente investigación.

Sep 20, 2019

By Carlos Vásquez Gonzales

El presente trabajo señala la metodología empleada para el “Diseño de la Explotación del Cuerpo Blanquita” del Abra de la mina Raura. Para tal proceso, se preparan dos tipos de modelamientos: el geológico, cual creó los sólidos del cuerpo en tres dimensiones y el de modelamiento de Bloques, donde se realizó el análisis estadístico y geoestadístico de las leyes, se interpoló las leyes, se calculó los recursos de mineral medidos e indicados, como se determinaron las reservas indicadas (económicas y marginales) con los Cut-Off y precios de los metales. De acuerdo a esto, se realizó el diseño de la explotación, definiendo el método de minado, la preparación, la secuencia del minado y las operaciones unitarias. Finalmente se calculó el tonelaje de producción, los costos y la evaluación económica.

Jul 31, 2003

By Fernando Machuca Pérez

"La minería genera una gran cantidad de desechos de material como lastre, ripios y escorias, que son depositados en un área sin considerar el impacto ambiental que estos producen. En ese sentido, el diseño de escombreras no considera las condiciones ambientales en la industria chilena, y por ello se privilegió el costo mínimo en depositar este lastre sin un diseño que considere esta variable. Por tal motivo, el objetivo general del texto es diseñar los algoritmos de secuencia de llenado de escombreras, considerando las siguientes variables forma, altura, talud y orientación, condiciones meteorológicas y económicas en su diseño, de tal manera que se produzca el menor impacto ambiental por la emisión de material particulado. "

Sep 1, 2015