Search Documents

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at 'higher overpotentials.

Jan 1, 1998

By P. D. Nolan

Smelters operating under pollution control orders have become increasingly dependent upon the reliable operation of sulphuric acid plants and no factor affects the long term reliability of those plants more than efficient gas cleaning. The sources and characteristics of contaminants in smelter of fgases and the conventional approaches to removing these contaminants to accepted levels are discussed. New technology is described which offers advantages of lower capital cost, lower operating cost and reduced space requirements over the conventional approaches. This new technology has been developed by LAB s.a. and is licensed for metallurgical gas applications by Chemetics International Company.

Jan 1, 1983

By Liwen Hu, Jianxun Song, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

The subchloride titanium was prepared by sponge titanium and titanium tetrachloride in the CaCl2 at 1173 K. The species were detected are mainly titanium dichloride, and the average valent in the melt are 2.05. The accurate equilibrium constants were obtained for the reaction 3Ti2+ = 2Ti3++Ti after the accurate activities of titanium chloride were evaluated with emf method, and the observed deviations from ideal behavior are discussed.

Jan 1, 2015

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction, The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory-scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the determination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the determined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors determining the time of reduction.

Jan 1, 2003

By Sacha Neven

Submerged lance technologies combine high intensity processing characterized by rapid mixing and reaction rates using a simple reactor design. The Isasmelt technology uses a central submerged lance to inject oxygen-enriched air and fuel into a bath thus creating large gas bubbles and intensive turbulence and splash. The lance is equipped with swirlers to increase gas velocity and heat transfer. This enables the formation of a frozen slag layer on the lance which protects it from the aggressive environment. Water models as well as high temperature reactors were used to validate the Davidson-Schiiler model on bubbling. Frequencies and pressure amplitudes were measured in a wide range of gas flow rates: from m3/sec using a water model to more than 30 m3/sec in an industrial process. Agreement with the model was satisfactory. The experiments however also clearly showed that cross-flow and bubble wake induce slightly higher frequencies. No influence of the use of swirlers on the bubbling frequency was observed in the water models.

Jan 1, 2002

By David S. Dolan

To beat capital costs of US$10 per pound of installed capacity has appeared as a major hurdle for the "third generation laterite nickel plants. Forecast costs are escalating. Where can savings come from? Ore beneficiation can reduce the tonnage rate to be processed. High pressure acid leach options include the use of indirect slurry heating and higher operating temperatures to reduce flow rates and residence time. Progress has been reported in atmospheric leaching. High counter current decantation circuit settling rates and high underflow densities reduce CCD costs. Metal recovery options include direct from leach solution to metal production, as used by Bulong and espoused by Goro, and indirect recovery as used by Moa Bay, Murrin Murrin and Cawse. Plant location impacts on the costs of tailings disposal, power and energy costs, supply of consumables and labour costs, among others. Final nickel and cobalt metal production routes are electrowinning, hydrogen reduction or some innovative routes being proposed for Goro. This paper reviews the status in these developments, with particular reference to equipment and processes that offer lower capital costs. Keywords: Laterite, Nickel, Plant, Capital Cost

Jan 1, 2004

By Peter Hayes, Evgueni Jak, Ata Fallah Mehrjardi

Modern analytical tools, such as electron probe X-ray microanalysis (EPMA), are used in experimental characterization of phase equilibria and microstructures of complex slags. Integrated thermodynamic computer packages, such as FactSage, are used to provide more accurate descriptions of complex slag systems. These advanced methodologies have been applied to characterize dynamic steady state freeze linings in slag systems using submerged cold finger probes at controlled laboratory conditions, establishing the effects of bath chemistry, temperature, heat extraction rate and bulk fluid flow. It has been found that stationary freeze lining deposit interface temperatures at steady state conditions can be lower than the bulk slag liquidus temperature, and that stable operation below the liquidus is possible. A conceptual framework has been developed to explain the phenomenon and the range of interface temperatures that can be obtained in dynamic steady state conditions. These findings have important implications for the design of freeze linings and possible improvements to high-temperature metallurgical operations.

Jan 1, 2014

By Nobuyuki Masuda

In Japan, the municipal solid waste, which amounts to 50 million tons, is generated every year and most of it is incinerated. The fly ash from the municipal waste incineration (the primary fly ash) contains heavy metals, such as lead and zinc, etc., and dioxins. In case of melting, the fly ash from the process (the secondary fly ash) contains high concentration of heavy metals (e.g., Zn; 1-20%, Pb, 1-10%). Metal Mining Agency of Japan launched a four-year project in 1999 to establish the integrated technologies to recover the valuable metals from, and to decontaminate, the primary and secondary fly-ashes in the practical scale by utilizing the existing metallurgical processes and facilities, along with the energy saving. The segregation, flotation and chemical treatment are applied to the treatment of the primary fly ash. The secondary fly ash is treated with MY (Mitsui-type blast furnace) Process after the chlorine removal to recover the heavy metals in the ash, In this paper, the segregation and flotation process for primary fly ash and MF process for secondary fly ash are explained. The main results of experiments done from 1999 to the mid of 2001 to design the pilot plants and to optimize the operating conditions are described. The main results of the experiments are as follows: - The segregation reaction of Cu was confirmed by the experiment on the treatment condition of 800 and 900`C with adding oil cokes and water to the primary fly ash, and 99.98% (toxicity equivalent) of the dioxins were decomposed by the treatment. - Washing tests of secondary fly ash to feed MF resulted that more than 70% of chloride were removed, but still lower than expected, and agglomeration tests were successful by the results of the sufficient strength of briquettes produced though a little more binder for the agglomeration is required than usual operation. - Smelting experiment by downsized MF showed that valuable metals, such as zinc and lead, are recoverable in the furnace dust. Recovery ratios, Zn: 58% and 67%, Pb: 74% and 83%, are accomplished.

Jan 1, 2002

By Andre Krzysik

"Fluidized bed technology has been used in the industry for almost 100 years. To fully understand the process hundreds if not thousands of researchers were and are involved in finding the way to predict the behavior of the solids when subjected to the flow of media through them and the conditions of the solids in the fluidized state. The difficulties in predicting the behavior of solids in the fluidized state stem from the complexity and abnormality of the parameters related to the solid particles. Theoretical calculations can in some degree account for some of them. Particle size distribution, their shape, density, moisture content and physical and chemical reaction that may exist in the fluidized bed reactor play an extremely important role and influence the behavior of the fluidized bed. This paper focuses on the practical examples of the fluid bed equipment and the use of different conditions to process various products.IntroductionEach process application has its own unique requirements and the designers of the equipment must take into consideration specific process requirements, specific properties of the material to be processed (both physical and chemical), and physical and chemical reactions/changes that are taking place in the reactor (heat and mass exchange, chemical reactions, isomorphic change etc.). Each individual piece of equipment must also satisfy specific requirements/ preferences of the client that will operate and maintain the equipment. Those often represent greater challenges than the process on its own, and are equally important to the satisfactory operation of the plant. That includes aspects like location of the equipment, environmental effects, and expected life of the equipment, process control, access, maintenance, and many others.Over the period of time a great deal of research, both theoretical and practical have been carried out and the results of that work are available for equipment designers. For the simple applications that information is usually sufficient and the selection of a suitable solution is relatively simple. In many instances, the available information is not sufficient, and often specialized test work needs to be conducted to obtain additional data. In many cases a pilot installation is built in which the required process is tested. Only then the commercial equipment is designed. The following deal with specific installations that were designed to satisfy specific requirements. In some instances, additional problems were discovered during the commissioning of the equipment that required on site modification. The continuous monitoring of the equipment that was supplied to the various clients allowed us to further develop and improve our designs."

Jan 1, 2014

By Cody Burcher-Jones

The recovery of rare earth elements (REEs) through heap leach/in situ techniques from so-called ion adsorption clays (IACs) is attractive due to their inherent simplicity. However, the underlying mechanisms of these processes are poorly understood. In this study, the deportment of REEs in a typical IAC material has been investigated and was found to concentrate in the phyllo-layers of the clays, especially hallyosite, and was readily desorbed by various ion-exchange reagents indicating various potential routes to liberate them. Here we are reporting the use of seawater (0.5 M NaCl), spiked with various amounts of (NH4)2SO4, and found better extraction using a reagent mixture than NaCl on its own. Further, the leaching of REEs from a bed of clay material was investigated over time to understand the rate of transport through the stagnant material. Results indicate that REE release is likely to be controlled by diffusion through the clay material, while desorption in agitated systems is rapid. A degree of fractionation between different REEs can be observed during diffusion. Nonetheless, the successful operation of in situ leach operations for this type of material would depend primarily on how easily solution cocktails can be made to flow through the bed material.

By T. J. White

Xtaltite is the trade name for a generic technology which exploits the well known insolubility of some minerals, which naturally incorporate toxic waste elements, to consolidate and immobilise a range of inorganic waste products. It is a specific case of synthetic mineral immobilisation technology (SMITE) which is already used to immobilise high level nuclear wastes (HLW. Although HLW is highly toxic, it exists in relatively small volumes, occurs in central facilities and may be stabilised at low waste loading (< 10 wt%). In contrast, heavy metal wastes are of considerable volume, therefore Xtalitite waste forms must routinely accommodate high waste loadings (usually in excess of 30 wt% for a particular toxic oxide or combination of oxides) and be suitable for fabrication in remote locations using relatively simple technology. This paper details the methodology underlying Xtaltite, with particular emphasis given to the interplay between solid state chemistry, durability and economic considerations. Specific reference is made to the treatment of arsenious and mercurial wastes.

Jan 1, 1994

By Fathi Habashi

Solid gas reactions of metallurgical importance can be classified into three groups: Physical processes, e.g., drying and sublimation Chemical processes which may be an addition or a thermal decomposition reaction Electrochemical processes which may be addition, oxidation-reduction, or displacement reactions. Examples are given and the role of the boundary layer is emphasized.

Jan 1, 1996

By Ted H. Eyde

Natural Zeolites are a less expensive and in certain applications a superior alternative to organic ion exchange resins. Mining and metallurgical waste streams are difficult to treat because the effluents which contain potentially valuable heavy metals such as copper, lead, and silver are often highly acidic and contain significant quantities of suspended solids. Under rigorous operational conditions, certain natural zeolites can remove the metals, which if desired can be recovered by either elution or conventional smelting techniques. There are significant differences in cation exchange rate, selectivity and capacity as well as resistance to either high or low pH, blocking cations and tolerance to elevated or depressed temperature and pressure not only between different zeolite minerals but between the same mineral from different deposits. Applying natural zeolites to the treatment of mining and metallurgical waste streams depends on matching the specific zeolite to the effluent by characterization of the zeolite minerals.

Jan 1, 1993

By Edwin de Jesús Deveaux

After 32 years of operations beneficiating lateritic nickel ore in a fully integrated pyrometallurgical complex, Falconbridge Dominicana (FALCONDO), situated at Bonao and La Vega Provinces, Dominican Republic, has become profitable with one of the lowest nickel grade content processing plants in the world, and literally without any by-product (granulated slag, will be utilized in the future as a post-processing subproduct). To December 2002, mineral reserves were 64.1 million tonnes containing laterite grading as low as 1.15 % Ni when full dilution is applied. At a cut-off grade of 1.20% Ni, the reserves will provide 15-20 years of production. The mineralized thickness over the seven active deposits averages 6 m. Development of very selective and unique mining practices, together with improvements in the process plant, are key to achieving the production goal (30 kt Ni/yr) and to meet the quality standards for the ferronickel produced. Keywords: Laterites, grade control, mining methods, environment

Jan 1, 2004

By Robin M. Forbes. Jones, Suhas V. Patankar, Ramesh S. Minisandram, Jr. Carter, Kanchan M. Kelkar

"The nucleated casting process currently under development has the potential for production of Ni-base superalloy preforms that possess superior microstructure to product made by conventional casting processes, primarily for gas turbine applications. In this process, electroslag remelted (ESR) clean (i.e., free of ceramic inclusions) molten metal is conveyed via a watercooled copper Cold-walled Induction Guide (CIG) to a gas atomizer. The spray of clean metal droplets is then directly cast into a water-cooled crucible for ingot production. The microstructure of the resulting ingot preform evolves within the length scale of the individual droplets and is a function of the thermal state of the incoming metal droplets. This, in turn, depends on particle size, flight time and heat exchange with the gas phase.In the present study, computational models is developed for the analysis of the flow and heat transfer in the gas-metal spray system under axisymmetric and steady-state conditions. The gasphase flow is analyzed using an Eulerian framework and turbulent mixing within the gas phase is modeled using the two-equation k-e model. The dynamics of the metal particles is analyzed using a Lagrangian framework that involves calculation of the trajectories of the metal droplets. A two-way coupling is considered whereby the transport and heat transfer in the gas and the metal phases influence each other.The analysis is developed at two levels. The spray model performs a detailed calculation of the spray dynamics in the vicinity of the spray and is intended for predicting the temperature and mass flux distributions of the metal spray depositing into the mold. The chamber model enables prediction of gas flow and motion of metal particles in the entire spray chamber."

Jan 1, 2004

By Kunibert Hanusch

Copper in recycling material is accompanied by various groups of metals: 1) Metals which are much more negative than copper, such as Fe, Al, Si, P, Be They are mainly removed by fire refining during the recovery of copper and leave the process in form of slag. 2) Metals which are more positive than copper or difficult to separate by fire refining and which are partly reduced together with the copper. These metals are for example As,. Sb, Ni, Ag, Pb, Zn, Sn. They are enriched in intermediate products and recovered from these or remain for their major part in the fire-refined copper and can be separated by electrolytic refining and recovered from the electrolyte or anode slime. This report describes the process of Hüttenwerke Kayser AG in Germany and illustrates how considerable returns of material are partly required to separate or recover associated metals. They are finally removed in saleable products.

Jan 1, 1995

By N. Verbaan, E. Bourricaudy, M. Dry

"Starfield Resources is developing a novel circuit for the recovery of nickel, copper, cobalt, iron oxide, sulphuric acid and precious metals from the Ferguson Lake deposit in Nunavut, Canada. In this deposit, pentlandite is too finely disseminated in pyrrhotite for the production of a smelter-grade nickel concentrate at an acceptable nickel recovery, so established technology is not applicable and a novel chloride-based circuit is under development. The enabling aspect of this circuit is the hydrolysis of ferric chloride to hematite, releasing gaseous hydrochloric acid that is recycled. Conventional steps are used for separating and recovering the valuable metals from the chloride solution generated. This paper briefly outlines the circuit and presents the results of experimental work on the enabling steps, viz. the oxidation and hydrolysis of iron chloride to hematite and gaseous hydrochloric acid.IntroductionThe Ferguson Lake bulk sulphide ore body in Nunavut, Canada, owned by Starfield Resources Inc., contains significant amounts of base and precious metals but its mineralogy is such that it is not amenable to conventional processing. Pentlandite, for example, is too finely disseminated in pyrhhotite for even modem techniques such as fine grinding and improved flotation reagents to be effective [ 1] and extracting the value requires processing the entire bulk sulphide, including the pyrrhotite. To give the project a total green footprint, in terms of both carbon emissions and acid rock drainage, Starfield imposed the following requirements:• No reactive tailings to generate acid rock drainage.• No gaseous emissions other than normal atmospheric constituents.• No liquid effluents.• No regular consumption of fossil fuel.• High recoveries of all the valuable metals."

Jan 1, 2011

By Andreas H. Vassiliou

Organic materials are major constituents of the ore in several uranium deposits. Some of these deposits have been described as "urano-organic" because, the organic materials are believed to have provided the dominant control for the accumulation and deposition of uranium and are directly and intimately intermingled with the uranium. The nature of these urano-organic deposits has been problematic in terms of (a) the origin of the associated organic materials and (b) the specific form of&apos; occurrence of uranium. The organic materials in urano-organic deposits have been genetically related to both coal and petroleum or their progenitors or deriva-tives. Analytical data presented here (infrared, chemical. D.T.A.) suggest that coaliferous materials or related plant derivatives represent the main source of the organic fractions in practically all major urano-organic ores analyzed from the Colorado Plateau and other areas. Recognition of the specific form of occurrence of uranium in urano-organic deposits has been problematic mainly because the uranium is usually in an extremely fine-grained and disseminated state in the organic matrix. Electron microprobe and X-ray diffraction analyses presented here show that fine-grained uranium minerals, specifically uraninite or coffinite. are disseminated in the organic matrix as the predominant form of uranium in most major deposits; however. the presence of true organo-uranium compounds is also suggested for some deposits.

Jan 1, 1981

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997