Search Documents

By John M. Gaines

Lead concentrates from the Viburnum Trend in the Southeast Missouri Lead district are sintered prior to smelting to bind the particles together homogenize the feed, and reduce the sulfur content. Good sinter forms competent masses about 4 to 6 inches across, that hal!e about 15% porosity and good mechanical strength to withstand transport and the weight of the overlying load in the smelter. Bad sinter has poor mechanical strength and forms fine fragments that retard the circulation of reducing gases in the furnace and lengthen the time required for reduction. The productivity of the lead smelter depends on good sinter feed. Because some lead sinter plants produce bad sinter about 20% of the time, this applied mineralogy study has been undertaken to determine the mineralogical and microtextural differences between good and bad sinter. A reflected light microscopic study of 130 polished sections has shown that good and bad sinters differ distinctly in their mineralogy, tex1ure. and character of, porosity. Good sinter consists of hardystonite, franklinite. lead-zinc-bearing magnesium-calcium silicate, lead silicate matrix, and large crystals of calcium-magnesium-iron silicate, together with minor amounts of lead oxides, lead-zinc silicate, metallic lead, specular hematite, magnetite, lead-iron-bearing zincite and zinc-Iead-magnesium-bearing wustite in a tightly intergrown mesh of crystals and with an evenly distributed porosity of 15% to 20%. Electron microprobe analyses show that the principal phases contain lead (or zinc): hardystonite (4-20% Pb) franklinite (2-14% Pb) and lead silicate matrix (65-74% Pb). Bad sinter differs from good sinter in the greater abundance of lead silicate matrix, galena metallic lead, and lead oxides and the lesser abundance of hardystonite, franklinite and calcium-magnesium-iron silicate. Bad Sinter is characterized by a lack of an intimate intergrowth of the constituent phases. Its porosity is much lower commonly 0 to 5% and those pores are concentrated in local areas rather than distributed evenly throughout the sinter.

Jan 1, 1991

By D. T. Smith, L. M. Hsiung, J. J. Schmitt, J. W. Golz, R. L. Lankey, H. N. G. Wadley, J. Z. Zhang, B. L. Halpern

"The microstructure and mechanical properties of Al/AI2O 3 metal-oxide nanolaminates fabricated by' a novel Jet Vapor Deposition (JVD) process at substrate temperatures of ~25° and -250°C have been investigated using transmission electron microscopy (TEM) and nanoindentation methods. The thickness of the oxide layer was held constant between 2 and 5 nm, whilst the Al layer thickness was systematically varied from -3 to -50 nm. Continuity of the Al layers was significantly improved when the nanolaminates were deposited at an elevated substrate temperature (-250°C). The yield strength of the nanolamintes with Al layers greater than -25 nm follows a Hall-Petch type relationship, whereas that of the nanolaminates with Al layers less than -25 nm is better predicted by a Koehler-Lehoczky strengthening model. IntroductionAluminum-aluminum oxide (presumably A12O3) nanolaminates have been recently fabricated using a novel Jet Vapor Deposition (ND) process developed and patented by Jet Process Corporation [1-4]. ND uses sonic, high purity helium (He) gas jets to entrain atomically dispersed vapor and deposit films. It is of interest here because it can deposit multilayered structures (laminates) inexpensively at high rates. Materials with a thin, multilayer structure are of interest because they potentially offer novel mechanical and physical properties [5]. Koehler in 1970 used an image force model to investigate the strength of laminated materials and proposed the use of alternating layers of high and low shear modulus metals to produce high strength composite materials [6]. He predicted that dislocations would have to overcome a large repulsive image force in order to move from metal layer B of lower shear modulus (uB) into metal layer A of higher shear modulus (uA)' The image force (F) is given by the relation:"

Jan 1, 1994

By Larry M. Southwick, Phillip J. Mackey, A. E. (Bert) Wraith, Albert Pelletier

In 1881, the first commercial pneumatic Bessemer-type converter treating copper matte was successfully introduced by Pierre Manhes at the Eguilles copper plant near Vedène in France. This development followed over a year of testing on a smaller scale at a foundry in Vedène, during which the vertical tuyeres of the conventional Bessemer converter had been successfully replaced by horizontal tuyeres in an effort to avoid the freezing of copper which had occurred in the bottom of the vessel having vertical tuyeres. The Manhes Converter, as it became known, was the first successful large-scale adaptation of the Bessemer concept of using compressed air blown into a melt for metal refining and treatment. Within a few years, Manhes Converters utilizing horizontal tuyeres in either the original type of vertical converter, or a later and more enduring horizontal barrel converter, were in operation at over a dozen copper smelters around the world. It was this process that Messrs Peirce and Smith essentially improved with the introduction of the larger converter which bears their name and the development celebrated at this Symposium. The present paper briefly traces the original development by Pierre Manhes in the early 1880s and which set the stage for the later Peirce-Smith adaptation. The paper observes that the original development by Manhes was in part driven by the need to reduce coal (energy) consumption and hence the production cost in order for Eguilles to remain competitive with the larger plants in Swansea, Wales, where a ready supply of cheap coal helped keep smelter treatment terms of the day low. These themes are eerily resonant of today where booming copper production in China has impacted the industry, and also where energy consumption, closely linked to today’s more familiar theme of ‘climate change’ remains an important challenge currently confronting the entire industry. The paper concludes with comments on these seemingly parallel situations today and offers some thoughts for the future.

Jan 1, 2009

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

By B. R. Davis, Neale R. Neelameggham, R. E. Brown

The element Calcium element has a unique place in the production of etals, intermetallics and other compounds. The unusualness arises from the fact that we have several possible reductants – metallic calcium, calcium carbide, calcium cyanamide and calcium hydride. A review of how metallic calcium is manufactured and utilized is presented. The difficulties involved in producing the metal in large quantities and price implications are noted. . Fundamental thermodynamics of how these act as reductants are shown, along with the historic application of these in metal production during the past century and a half. Alternate applications as to how to control the cost of the reductant is indicated, such as the numerous attempts in making low cost titanium utilizing direct or indirect calcium reductant.

Jan 1, 2014

By Raj P. Singh

Applications of cementation in the recovery of metal ions from process solutions have been known for a long time. Cementation reactions involve electrochemical precipitation of a noble metal from solutions of its salts on a more electropositive metal which, in tum, progressively dissolves. For example, addition of zinc metal powder in a solution containing zinc and cobalt ions would allow for the precipitation (separation) of cobalt according to the following chemical reaction. This paper pertains to the recovery of cobalt from cobalt process solutions via a cementation reaction on aluminum shavings (metal scraps from cans etc). Specifically, we report on the characterization of cobalt process solutions, a by-product obtained from cobalt chemicals, and the kinetics of cobalt, nickel and manganese cementation from process solutions on aluminum shavings.

Jan 1, 2000

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping, Zhai Dacheng

"Corrosion resistance of RE-Ni-W-P-SiC composite coating and 3 l6L stainless steel in corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations by means of immersion methods and anodic polarization curves obtained by DHZ-1 electrochemical synthetic tester and HDV-7 transistor constant potentiometer. Immersion experiment results show that corrosion rate of RE-Ni-W-P-SiC composite coating as-deposited in HCl solutions increases with the rise of HCl concentrations, on the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing the HCl concentrations the corrosion rates of the coatings as-deposited and after heat treatment in H2SO4 and H3PO4 solutions respectively decrease with the rise.of H2SO4 and H3PO4 concentrations the corrosion rate of the deposit as-deposited in FeC13 solutions decreases with increasing FeC13 concentrations, while the rate of the composite coating after heat treatment increases .with the rise of FeC13 concentrations.In addition, the corrosion rate of 3 l 6L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations increases with rising of concentrations. Furthermore, the corrosion rate of 316L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions respectively is much greater than that of the RE-Ni-W-P-SiC composite coating as-deposited and after heat treatment in the same corrosion media.1. IntroductionAll the materials and their products, when processed, stored and used, it is inevitable that the corrosion, wear, fatigue and crack occur owing to the actions of surroundings. Those early failure and abrasion, through all kinds of departments and profession that corrosion consumes one percent of tens of the steel products of the whole world; and two or four percent of the GDP is lost because of the corrosion."

Jan 1, 2000

By Hideya Sato

Refractory wear caused by melts is one of the major determining factors for the interval of shut-down repair of the metallurgical furnaces in general. Calcium ferrite slag employed by M it subishi Continuous Copper Converter, shows hi& fluidity and corrosive characteristics against most of the refractories. In order to improve the corrosion resistance of the refractories, the mechanism of MgO-based refractory wear by the calcium ferrite slag was intensively studied. The dissolution behavior of the refractory into the molten slag and the penetration of the molten slag into the refractory were observed by crucible tests and newly developed oscillating furnace tests. It was found that the wear of MgO-based refractories by the calcium ferrite slag is mainly dominated by the internal structural failure caused by the penetration of CaO-Cu20 rich slag which is formed as a result of the preferential absorption of FeO, from original slag by the spinel of the refractory.

Jan 1, 1999

By Brian G. Thomas

Quality problems in continuous casting of steel can be identified as they occur by monitoring mold signals (level sensor, thermocouples in the mold walls, friction etc.) and taking appropriate action (such as slowing casting speed, changing taper, changing a clogged nozzle, or later visual inspection of the surface for possible downgrading. Surface depressions and groups of deep oscillation marks form at meniscus and reduce local heat transfer as they move down the mold at the casting speed. This slows shell growth, increases shell surface temperature, and causes characteristic dips in mold thermocouple signals. More importantly, they are also associated with longitudinal cracks. Characteristic thermocouple signatures have been identified for many defects, including sticker breakouts, transverse depressions and deep oscillation marks, narrow-face bleeds, transverse comer cracks, longitudinal cracks, mold level fluctuation defects, and other problems. With the help of computational models, these mold signals should be used to troubleshoot defects, and to take appropriate corrective action. Keywords: Continuous casting, defect detection, thermocouple signals, on-line control

Jan 1, 2003

By Wang Yun-yan

In order to examine the adaptability and the kinetics of leaching different gold ores in alkaline thiourea system, six kinds of gold concentrate and/or calcine with different physical and chemical properties were chosen as objects. The leaching behaviors in alkaline thiourea system with high stability, acidic thiourea system and alkaline cyanide system were compared. Changes of phase, surface appearance, particle distribution and specific surface area of six kinds of gold ores before and after leaching were studied in virtue of modern analytic techniques, e.g., XRD, SEM, and so on. The results indicate that alkaline thiourea solution can be used to leach gold ore, for oxidized gold concentrate removed arsenic by microbe pretreatment(4#) the leaching rate of gold is up to 82.68%, such conclusion overthrows the parlance reported that pH value must be less than 1.78, or gold can not dissolve in thiourea solution. Chemical components and phase are related to gold leaching rate, different gold ores are fit for different leaching system, and alkaline thiourea solution is suitable for the pretreated oxidized gold ores with low content of sulfur and in which the main phase was SiO2, phase almost does not change after leaching basically. Generally speaking, when leaching in alkaline thiourea solution, surfaces of gold ores with glaze change greatly to ones with coarseness, distinct trace and holes of corrosion. Particle size decrease and specific surface area increase of gold ores after leaching in alkaline thiourea solution with high stability except gold concentrate of Zhongyuan gold smelter(5#).

Jan 1, 2006

By Larry B. Fiske

Elimination of dust and processing of fines for both thermal and metallurgical coals is addressed. The efficiency of treatment with lignosulfonates compares favorably to oil in thermal coal. Effect of treatment with various lignosulfonates upon cokability of metallurgical coal was determined by Free Swelling Index, Gieseler Plasticity and Arnu Dilatation.

Jan 1, 1992

By Baozhong Zhao

Experimental results have shown that fluxing with soda ash (Na:zC03) can remove As and Sb from molten copper at the rate of As>Sb, but is relatively ineffective in removing Hi. The rate of impurity removal is controlled by impurity mass transfer in the metal phase. In this paper, a mathematical model was developed to describe the impurity removal phenomena. The model incorporates the effects of molten bath mixing intensity, soda ash feeding rate, oxygen content in the molten copper and soda ash fluxing by surface addition and injection. The model predictions are in good agreement with experimental results and may be used in designing large scale tests.

Jan 1, 1996

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By R. W. Smith

The flotation response and electrokinetic behavior of Chlorella vulgaris and Chlamydomonas sp . when using dodecylamine hydrochloride as collector were studied in the absence and presence of Pb(I1). Also, an electron microscopy study was made of the algae after Pb accumulation. The flotation behavior of the organisms after Pb accumulation appears at least partially related to the location of the abstracted Pb onto or into the organisms.

Jan 1, 1991

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By Herbert H. Kellogg

A model of the ISF is described. which reproduces with accuracy the "normal" operation of three industrial furnaces. The model, written in Fortran, is based on detailed heat and material balances, and the concept that the ascending gases reach equilibrium with zinc oxide and with the water-gas shift reaction. "Solution loss" of carbon in the lower shaft, and partial reoxidation of zinc vapor in the upper shaft are also essential features. For prediction of furnace behavior under altered operating conditions (blast rate, temperature, moisture content, oxygen enrichment, or injection of oil or coal through the tuyeres) the model modifies the heat loss, temperature of slag and bullion, amount of reoxidation in the upper shaft and the condenser efficiency to reflect the altered operating parameters. Model predictions for such operating conditions are in reasonable agreement with plant experience.

Jan 1, 1990

By Rodney Hundermark

At Anglo American Platinum’s Polokwane Smelter, radar instruments are being used to provide continuous measurement of the concentrate feed level in the six-in-line electric furnace used for smelting of nickel-copper concentrates containing platinum group metals (PGMs). The radar instruments are installed directly on the furnace roof, and a mechanical system has been designed to protect them from radiation and elevated freeboard temperatures and pressures. Signal validation criteria have been implemented to ensure that proper level measurements are being used by the PLC system. The feedback from the radars has provided an improved understanding of the furnace behaviour with respect to concentrate feed level control, individual feeding events, global feed rates, feed distribution and bath disturbances. In combination with a dynamic mass balance for continuous calculation of liquid level in the furnace, the radar measurements have enabled more precise feedback control of the concentrate blacktop depth. In turn this has yielded improvements in furnace stability.

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.