Search Documents

By Khaled Morsy

The tragic incidents at Sago and Darby coal mines in 2006 pointed out the need for stronger seals to resist the blast effects of violent gob explosions. Mine Safety and Health Administration (MSHA) has published the final rule on Sealing of Abandoned Areas in April 2008. According to the final rule, the mine seals for unmonitored gob areas should withstand an instantaneous pressure of 120 psi. Reinforced concrete (RC) seal is one of the feasible options that can be used to meet the final rule. Concrete is a heterogeneous, cohesive-frictional material and exhibits complex non-linear inelastic behavior under multi-axial state of stress. The increased use of concrete as primary structural material requires the development of sophisticated material models to have an accurate prediction of the material response to a variety of loading situations. The constitutive modeling of concrete has advanced considerably in the past three decades. Choosing a reasonable concrete material model is important in order to obtain an accurate mine seal design. This paper attempts to address the effect of different concrete material models on the response of RC seal subjected to dynamic loads from methane explosion. Three concrete models, from ABAQUS library, were selected to address the effect of non-linear behavior of concrete and damages due to tensile and compressive stresses. In addition, a typical and verified concrete material model was used for conducting 3D finite element models simulating the RC seal by ABAQUS, EXPLICIT ver. 6.6.

Jan 1, 2008

By Thomas M. Barczak

With the development of the shield support, the primary requirement for successful ground control in longwall mining is to provide stable gate road and bleeder entries. Wood cribbing has been the dominant form of secondary support. However, the cost and limited availability of timber, along with the poor performance of softwood crib supports, has forced western U.S. mines to explore the utilization of other support systems. The recent success of cable bolts has engendered much interest from western operators. Several innovative freestanding support systems have been developed recently including: (1) "The Can"' support by Burrell Mining Products International, Inc., (2) Hercules and Link-N-Lock wood cribs and Propsetter by Strata Products (USA) Inc., (3) Variable Yielding Crib and Power Crib supports by Mountainland Support Systems, (4) the Confined Core Crib developed by Southern Utah Fuels Corporation; and (5) the MEGA prop by MBK Hydraulik. This paper assesses design considerations and compares the performance and application of these alternative secondary support systems.

Jan 1, 1996

By Greg Hendon

Various methods have been used to evaluate the effectiveness of shields in place. The most common method used is static recording of leg pressures by visually examining pressure gauges. In an effort to more closely examine the shield cycle and therefore the shield effectiveness, Jim Walter Resources has implemented a program of monitoring utilizing a polycorder system which is capable of recording convergence and pressure measurements on a continuous basis. This paper will discuss two longwall panels at Jim Walter Resources which have been monitored.

Jan 1, 1990

By John Feddock

A recent increase in energy demand has resulted in the rapid growth of coal consumption in the People?s Republic of China (PRC), which is the largest coal producer and consumer in the world. Reportedly, the safety issues in Chinese coal mines have been improving, but the number of fatalities and serious injuries continues to be alarmingly high. The number of fatalities from catastrophic accidents have prompted researchers to review the Chinese mine safety situation and to look for potential solutions. Marshall Miller & Associates, Inc. (MM&A), along with various collaborators, has investigated these issues as part of its work on various projects in the PRC and has discussed the concerns with relevant Chinese officials. Preliminary investigations by MM&A of coal mine accidents during 2001?2006 in the PRC indicate that 65%-78% of the total fatalities were the result of gas explosions and roof falls in underground mines. Even though the drainage of methane has been practiced for decades, current practices do not always produce satisfactory results due to technical constraints and equipment limitations. Based on prior experience of in-seam degasification at the Daning Coal Mine located in Shanxi province, MM&A believes that in-seam directional drilling technology can be a viable solution to degas the low-permeability Chinese coal deposits. This paper 1) reviews current Chinese coal mine safety conditions, 2) analyzes the advantages/disadvantages of current degasification practices in China, and 3) presents the pre-mining degasification practices for the longwall panel at the Daning Coal Mine.

Jan 1, 2007

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By Da Zhao Gu

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By Sam Spearing

Free-standing supports are commonly used in coal mines in the USA, particularly when longwalling. A recent trend has been the development of prop supports. Prop supports have many advantages over bulky, crib-type secondary standing supports, particularly in regard to material handling and installation. The challenge in prop design has been to develop load capacities that can compete with crib type systems and to develop reliable (stable) yielding capability. This paper will focus on the design aspects of steel prop supports, specifically, and evaluate the various concepts that have been developed to provide easy height adjustment and sustainable stable yielding under load. The design and resulting improvement provided by recent support developments called the Quik Stik and Ball Buster are discussed in detail. Performance areas that still need improvement in the design and usage of free standing supports in general are identified and possible solutions outlined.

Jan 1, 2008

The basic objectives of mine roadways are to provide sufficient cross sections in order to meet the needs of accommodation of equipment, transport, personnel travel and ventilation. However, many roadways become damaged to the extent of needing maintenance, generally dinting, and in some cases requiring re-ripping. The damaging of a roadway is a result of several factors including geological properties of surrounding strata, method of roadway formation, type and spacing of support and so on. Among these factors, strata conditions play an important effect on the stability of roadway. Weak rocks cause excessive roadway closures and water softens some rocks and promotes the closure problem. In this paper, a scientific discussion on the effect of water on the stability of roadways is given on the basis of results obtained by means of in-situ investigation and laboratory rock tests.

Jan 1, 1996

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Yoginder P. Chugh

The characteristics of weak floor strata associated with actively mined coal seams in Illinois are very important from ground stability point of view and, in many cases, are the governing factors in determining the size of pillars and mine openings. Laboratory and field getotechnical characterization studies of weak floor strata were conducted at six mines during the period 1985-1988. Correlation analysis among engineering index properties, and laboratory, and field determined strength-deformation properties were conducted to identify simple tests which can be used to estimate ultimate bearing capacity and deformation properties of immediate floor strata. It was concluded that the ultimate bearing capacity (UBC) and strength- deformation properties of the weak floor strata can be estimated from simple tests such as, natural moisture content, atterberg limits, and axial swelling strain. Indirect tensile strength was found to be a better estimator of UBC than unconfined compressive strength.

Jan 1, 1989

By Murali M. Gadde

Welded wire mesh is the most commonly used skin control technique in the United States underground coal mines. Currently, selection of the mesh is based on trial and error rather than any rigorous design methodology. Several factors affect a wire mesh?s performance including the amount of rock material to be supported and how the load is distributed, wire gauge, aperture size, grade of steel, weld strength, bolting pattern and sheet size. Although the best way to choose the mesh is to conduct full-scale physical load tests, because of the limitations on the number of variables that can be considered in such tests and the requirement of an elaborate test set-up, it may not always be possible to use this option. An alternative would be to use numerical modeling to study the load-deformation behavior of a wire mesh. In addition to providing a very detailed stress, strain distribution in the entire mesh, the advantage of this approach is the ease with which parametric studies can be conducted. In this paper it is shown that the load-deformation curves generated by nonlinear numerical models match closely with laboratory derived ones. Then, based on parametric studies, design guidelines are developed to choose the mesh appropriate for different loading conditions. The modeling studies also bring forth the limitations of the current lab studies. For example, under some conditions it was noticed that the small sheet size considered in lab tests would produce higher mesh deformations than a full-size one used in actual practice.

Jan 1, 2006

By D. S. Choi

This paper describes an improved source location technique for microseismic events related to coal mining. A system of non- linear distance equations is solved with the use of the Newton-Raphson method. This computational method is- advantageous when the number of geophones is limited. In addition, this paper includes the results of the analysis of data from several instruments which characterize both mine seismicity and environmental noise such as vehicle traffic. Analysis of the mine seismicity has contributed to a better understanding of caving above a longwall gob and of what constitutes stable ground conditions.

Jan 1, 1990

By Thomas A. Bailey

Since the advent of longwall mining, various methods and materials have been used during relocation to control the intrusion of the gob in the shield/panline area. (figure 1) Controlling this gob is critical to ensuring a safe, speedy, and productive longwall move. An uncontrolled gob can cause a number of problems, from increased worker exposure to entrapment of equipment to lost production. With an eye toward worker safety and increased productivity, several different methods have been developed to minimize gob intrusion. This presentation will take a look at the history and development of longwall ?screens? and ?mesh?, from chain-link fencing to high-modulus polyester geogrids. The benefits and advantages of these developments will be defined. Since 1994, longwall coal mines have used polymer geogrids during longwall recovery to control intrusion of gob material into the shield/pan line area. As described by Brandon and Collins (1996) in their paper presented at the 15th Ground Control Conference in Golden, CO., mines had used various forms of support, such as welded wire mesh, chain-link fencing, wooden cribbing, props, and steel cable to accomplish this. These methods worked, but were labor-intensive, slow, and provided varying degrees of gob stoppage. Although a few mines still use chain-ink fencing to control the gob, longwall coal mines have generally settled on polyester geogrids to control gob and roof and these mines have been instrumental in providing input in order to develop and improve these geogrids products. he trend during the past twelve years has been to incorporate stronger grids and to eliminate auxiliary reinforcements, such as steel cables and nylon or polyester webbing. A job that once required heavy steel cables, props, and fencing is now accomplished with strong, lightweight, high-modulus polyester grids. When we discuss high-modulus grids, we refer to the ratio between load and strain, as illustrated in figure 2. These grids are woven or knitted from yarns that have been pre-stressed. When these grids come under load, they pick up the load more quickly. This allows less deformation in, in this case, the mine roof. The same principle applies when these grids are used to control the ribs. With less elongation, the grids will hold rib material tighter, thereby keeping travel ways more open.

Jan 1, 2006

By D. S. Choi

This paper presents a theoretical analysis of the effect of shape and size on strength of geologic materials. The results indicate that the shape effect is caused by the development of confining pressure at the interfaces. The linearization of the obtained formula is of the same form determined by experiments. The size effect is attributed to the fact that the geologic materials contain discontinuities in the form of fractures, bedding planes, and cleats. The maximum reduction factor for the size effect is the one-sixth power of the volume of a cubic test specimen. The results of this work are particularly useful in determining the strength of coal pillars in underground mines.

Jan 1, 1989

Recent improvements are described in several techniques for ground control in underground mining. Promising methods for analysis and mitigation of rockbursts are discussed. Methods of assessing damage to underground excavations from repetitive seismic loading are reviewed. Analysis of mining-induced surface subsidence is discussed.

Jan 1, 1989

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992

By Frank Chase

Longwall mining has gained the reputation as being the safest extraction method in underground coal mines. However, one of the most difficult tasks associated with longwall mining is moving the face once a panel is completed. Based on Mine Safety and Health Administration (MSHA) fatality reports since 1996, longwall face recovery operations have claimed the lives of 5 U.S. miners and have resulted in numerous injuries. Recovery operations can be hazardous because they involve moving large pieces of equipment in very confined spaces. They are also conducted in highly stressed ground conditions due to front abutment loads generated by panel extraction. Shield removal is the most hazardous operation during face recovery because miners are constantly exposed to the unpredictable gob edge. To protect the miners, one or more walking shields, cribbing and/or other supplemental roof and standing supports are typically employed as breaker line supports as each shield is removed. At the Harris No. 1 Mine in southern WV, mobile roof supports (MRS?s) have been used in lieu of traditional walking shields on 17 face moves since 1997. MRS?s are shield-like support units mounted on crawler tracks and are commonly used during room-and-pillar retreat mining operations. For longwall recovery, the two biggest advantages that MRS?s have over traditional walking shields are that they are remotely controlled and are highly maneuverable. MRS?s have contributed to safer shield recovery and shorter move times at the Harris No. 1 Mine. This paper will address both the safety and the operational issues associated with MRS usage during shield recovery. It will also discuss new developments, including the use of the inherently safer battery powered MRS?s, which have been recently certified by the Mine Safety and Health Administration.

Jan 1, 2007

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

By Ray Brandon

The recent introduction of polymer geogrids for ground control purposes in underground mines allows mine operators more flexibility in choosing improved products for several applications. This is evidenced most clearly in longwall recovery operations. Since November, 1994, many mine operators have chosen Fortrac geogrid assemblies for the purpose of securing longwall recovery areas prior to shield removal. Fortrac is a lightweight, strong, and flexible polyester geogrid available in many strengths. Utilizing the "diamond" seaming method, different strengths of Fortrac geogrids are easily fastened together so stronger geogrids may be placed in the most critical areas and lighter geogrids in less critical areas.

Jan 1, 1996