Search Documents

By William A. Turcotte

Introduction The need for water is fundamental to every minerals processing operation. Though this may sound rather elementary, it is one area that cannot be over- looked. Frank C. Quinn in his paper entitled "Water Is Water Is Water" (1967) said, "but it isn't as simple as that. Very often research is slowed down and production is hampered because of a lack of appreciation for the behavior of water." The quantity of water needed for any operation is determined from bench and pilot plant testing. The quality required by the process for both fresh and reuse water is also established during these two testing phases. Quinn's statements are true whether the process involves the paper industry, the minerals industry, or any other industry. It is not the author's intent to cover water quality, quantity, or re- cycle in specific terms, but to provide the reader with a general outline of the topic with reference to several valuable sources of information. The first part of the chapter will cover several of the areas that have been de- tailed by others and also provide a list of reference sources. The references at the end of the chapter are not all inclusive but will provide a good starting point. In the second part of the chapter, a detailed description, with flowsheet illustrations, is pro- vided on the evolution of the reclaim (reuse) water system at the Tilden concentrator. Mineral Industry Water Needs Beresford and Edler (1978) surmnarized the minerals industry's need for water this way: "minerals are necessary to a modern complex technological society. The minerals industry, while its water needs are relatively minor compared to large users such as agriculture, nevertheless requires a large quantity of water to carry out daily operations from mining to final product refining." In 1973 total water use in the United States was estimated at 15.14 billion cubic meters (4 trillion gallons) for the minerals industry. Of this, about 69% was recirculated within the system. In 1982 Watt and Horton stated that the percent of recycled water in the minerals industry had improved to 73%, showing the minerals industry is an efficient user of water and that steady improvement in water recycling is something the minerals industry can look to with pride. The percent of water needed by the United States' minerals industry was estimated in 1962 to be about 2% of the total water required by industry

Jan 1, 1986

By G. Machiavelli, P. Bevilacqua, G. Ferrara, T. P. Meloy

During several years of operation in Europe, South Africa and other locations, the Tri-Flo process has demonstrated substantial improvements in dense-medium dynamic-separation systems. The reasons for this improvement are: • a high-sharpness separation due to the multistage system and the application of new concepts in the design of the regeneration circuit and in the control of the medium Theology, and • the possibility of performing two cuts at different densities using a single separation device and a single regeneration circuit. This paper discusses the above points in detail with particular reference to the multistage technology (based on the circuit analysis theory) and to the control of the medium rheology (based on recent work in the modeling and simulation of the rheological behavior of dense suspensions). Concerning the multidensity separation, information is given on the new three-stage separator where the high-density separation is performed by the first stage and the low-density separation is performed by the second and third stages. This configuration (already realized in two operating plants) was selected because no particular sharpness was required at the high-density separation, while high sharpness was required at the low-density separation. However, the configuration can be inverted or a fourth stage can be added (at very low additional cost) to provide two stages for each separating density. The importance of achieving a high sharpness separation is related to minerals (industrial minerals in particular) where the density difference of the phases to be separated is very low (as in processing of lithium ores, feldspar- and others). Information is provided on plants operating in South Africa and Canada, for the beneficiation of lithium minerals and on a plant under construction in Italy for the beneficiation of feldspar. Finally, the importance of making the separation at two densities is emphasized with particular reference to coal; i.e., producing a low-ash premium coal and recovering, in the middling, a by-product without losing heating value. Also, very important for some minerals is the production of a high-grade concentrate (at the first stage) suitable for sending directly to metallurgy (e.g., chromite ores) and the production of a low-grade concentrate that can be further treated. In this way, a higher overall recovery of the valuable mineral can be achieved, and, at the same time, a reduction of the treatment costs can be obtained. All of the above applications were once considered impossible.

Jan 1, 1995

By Dale Brunton, Robert Adams, Michael Dutton

Tunnels and other underground structures are typically designed using ground-structure interaction models instead of traditional structural analysis programs. This allows for the degree of load sharing etween the two odies to e calculated allowing for a more efcient design. hile modern codes outline the use of limit states with factors on applied actions, limit states are not typically compatible with ground-structure interaction models. Consequently, the engineer is left to develop rational methods for incorporating load factors into their analyses. Several methods can be considered, including the Largest Factor Method, Averaging Method, Subtraction Method, and Split Factor Method. This paper discusses the approaches, compares their effects using a case example, and provides a recommendation for designers.

Jun 23, 2024

By Ashma Singh, Nichole Maistry

Due to declining iron ore grades, low-grade ores with complex mineralogy — namely, banded iron formation (BIF) — are being explored to maximize iron ore resources and increase the life of mine. Flotation is the standard global process used for the beneficiation of BIF ores, as it is a complex ore reserve, and liberation is typically achieved below 1 mm. This study focuses on the flotation of a South African BIF, evaluating its response to different collectors, as well as effect of grind. As flotation is an expensive process and South Africa ranks high on the production cost curve, preconcentration by gravity or magnetic separation is performed prior to flotation. Thus, flotation was also performed on a gravity concentrate to determine if a grade suitable for steelmaking (approximately 63 percent) is achievable. The results indicate that the use of an alkyl ether amine-based collector partially neutralized with acetic acid is suitable for separation of hematite from illite and quartz at high pH values. Further optimization tests are being pursued to improve overall recovery and grade.

May 1, 2025

By Peter C. Busse, Henry M. Giegerich, Ronald K. Netolitzky

Zimbabwe The Republic of Zimbabwe is situated in south central Africa and north of the Tropic of Capricorn. The country is land-locked, bounded on the north by Zambia, on the south by the Republic of South Africa, on the east by Mozambique and on the southwest by Botswana. Nearly 400,000 sq km in area, Zimbabwe is bigger than both France and Spain and nearly three times the size of England. The outstanding physical feature is the central plateau, known as the highveld, which is about 650 km long and 80 km wide at an elevation of +1,200 m, and on which the Jena Mines is located. Because of its elevation and inland position, Zimbabwe's climate is temperate, generally drier and cooler than is normally expected in the tropics. Zimbabwe's population is in excess of 10 million. English is the official language, with Ndebele and Shona being the main ethnic languages. About one million people live in Greater Harare, the capital city. The basic unit of currency is the Zimbabwe dollar, which has depreciated substantially over the past few years. Currently (November, 1995), the exchange rate is $US 1.00 = $Zim 9.00, compared with $US 1 .OO = $Zim 2.50 in 1991. Project Area The Jena Mines Complex is situated in central Zimbabwe (Figure 1), in the Silobela area of the lower Gweru River valley. The mine site is 270 km from Harare by paved and gravel road. The Jena Mines property consists of a single rectangular (8 km by 5 km) shaped mining lease with an area of approximately 40 sq km (Figure 2). Annual average precipitation is 720 mm falling in the summer months between October and April. Mean daily maximum temperature is 24°C in October and mean minimum is 14°C in July. The southern parts of Zimbabwe have experienced drought conditions over the past four years which has affected water and power supplies. The countryside in the Jena area is generally low relief with a gentle slope to the northwest. The mine site topography is flat with an average elevation of 1,210 m. Zimbabwe Mining Industry Zimbabwe has a long mining tradition, particularly for gold. In the 1,200 years preceding European colonization, it is estimated that about 4,000 ancient mines produced between 600 and 800 tonnes of gold. Since the turn of the century more than 1,700 tonnes of gold have been produced. An excellent infrastructure has developed to support the mining industry. This includes a well- maintained system of paved roads, railway links to major mining areas, an electricity grid covering most of the country, and numerous industries manufacturing a wide range of mining supplies. Jena History The claims in the Jena Mines area are among the earliest registered in Zimbabwe. The gold potential was easily recognized because of extensive ancient (pre-European) workings. European trading beads from the 14th Century have been recovered from anthills in the mine area. Development of the Jena Mines commenced in 1898 and several mines have operated intermittently over the past 90 years. The recorded cumulative historical production from the significant producers of Jena is tabulated in the following:

Jan 1, 1996

By J. Bowders

A case study describing the expansion of Marion County landfill is presented. The exapansion area is located on a deep mined area. Finite element analyses were used to predict the surface subsidence and associated tensile strains on the landfill liner of the expansion site. A synthetically reinforced liner system is recommended to minimize the impact of the subsurface movements on the integrity of the liner system.

Jan 1, 1986

By Justin Brown, Michael Kobler, Dave Ragland, Bob Shufflebotham

PROJECT OVERVIEW As the sun-bronzed San Diego students strolled casually to class, mining crews from Atkinson Construction were working only 9 meters below the surface. The330 meter long, 11.3 meter diameter squat ellipse NATM tunnel is part of the9.3 kilometer Mission Valley East Extension Light Rail Transit (MVE-LRT) being constructed for the San Diego Metropolitan Transit Development Board (MTDB). The SDSU segment of the MVE-LRT was awarded to the Clark Construction Group, the parent company of Atkinson Construction for $82.7 million. URS CORP was the prime designer and Hatch Mott MacDonald performed the NATM tunnel design. The construction managers were Washington Infrastructure Services with Underground Construction Managers, EPC Consultants, and ILF Consultants. A NATM tunnel design was chosen as the most cost-effective way to minimize disruption of the university activities. The tunnel passes close to several buildings and directly below access roads, tennis courts and a baseball field. The NATM method of conventional mining uses shotcrete for ground support often reinforced with steel orplastic fibers, welded wire mesh and lattice girders. The tunnel runs from a cut and cover box up a 4.2% grade in a 217 meter radius left-hand curve with several spirals and ends at the underground station 330 meters away. The depth of cover varies from 16 meters near the west portal to nine meters at the station. The design called for a two-pass system with a primary lining of 300 mm shotcrete with lattice girders at 1 m centers and two layers of welded wire mesh. The lattice girders are used primarily for profile control and are not considered a structural element. The top heading was designed to be excavated in one of three excavation sequences depending on ground conditions and depth of cover. In sequence one excavation, the top heading is excavated in two halves with a one-meter separation. In sequence two excavation, a side gallery is advanced 8 or more meters ahead of the

Jan 1, 2003

By K. A. Eriksson

Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind -and Secondary Mills. There are, however, only a few Primary Mills in operation with "solid" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a cost per ton basis and/or downtime for liner replacement would be too high.

Jan 1, 1988

By H. L. Bourne

Not everyone understands the concept of mineral royalty. Mineral royalty is a fee paid to a landowner by someone who extracts a mineral commodity from the owners property. The royalty contract between the lessor and lessee contains clauses and conditions that are significant to both parties, e.g., annual m1n1mum, escalation factor, duration of the lease, reclamation and assignability. Comparison of royalty rates requires knowledge of many conditions that influence the value of a given deposit. People in several different professions benefit from shared royalty information.

Jan 1, 1989

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By Penglu Gan, Jinjie Zou, Chenglang Pan, Xiaowu Tang, Yu Zhao

"The north segment of the Zizhi Tunnel that consists of twin tunnels was excavated at a shallow depth in soft ground using the Shallow Tunneling Method. Based on continuous field measurements, the development histories of surface settlement were analyzed first. The observed development process could be roughly divided into three stages and the influence of river was evidenced. Transverse and longitudinal surface settlements above the twin tunnels were then fitted with empirical models. The obtained trough width parameters in transverse and longitudinal direction (it and il) and the volume loss (VLs) were presented and discussed. Additionally, surface settlement was compared with the crown settlement. The relationship between surface and crown settlement behaved in two different ways inside and outside the river-affected region. The findings in this project give references for predicting surface settlements in similar tunneling condition. INTRODUCTION Nowadays tunnel construction has become a major way of utilizing underground space in many large cities. The ground deformation will be inevitably induced in the tunneling process. Engineers should always be careful about excessive deformation that may damage adjacent structures. For shallow tunnels, controlling ground deformation turns to be more risky. Since soil arching is not completely formed in the shallow tunneling, settlements can easily develop from tunnel crown to ground surface.A conventional tunneling method named Shallow Tunneling Method (STM) has been developed and widely applied to constructed shallow tunnels in China. The major difference between this method and the New Austrian Tunneling Method (NATM) is whether considering self-supporting capacity of surrounding ground or not. In order to reduce the disturbance of surrounding soils, several guidelines are highlighted in this method, including advanced pipe forepoles, strict grouting, short excavation length, strong support, quick closure and frequent measurements (Fang 2012). Nevertheless, the ground deformation is still hard to control and becomes a concerned problem, mainly because ground settlement has some regional features and largely depends on the detailed excavation methods (bench cut method, multiple heading method, etc.) and ground condition (sand, clay, decomposed rock, etc.)."

Jan 1, 2016

By M. R. Yalamanchili, C. A. Young, J. J. Kellar, W. M. Cross, J. D. Miller

Introduction Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available that allow direct in situ analysis of adsorbed layers. With reactive internal reflection elements (IREs), Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IR/IRS) allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar. 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Fig. I is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/dodecylsulfate, CaCO3/oleate, ZnS/xanthate and KCI/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990). Of particular interest to flotation chemists is the conformational behavior of the alkyl chain of adsorbed collector molecules. In the simplest sense, conformation can bethought of as the relative flexibility of the hydrocarbon chain caused by rotations about carbon-carbon single bonds. The flexibility is described by the amount of gauche/trans conformations in the alkyl chain. Figure 2 shows examples of gauche and trans conformations (rotational isomers or rotamers) in a hydrocarbon chain. These two conformations are observed when the terminal methylene groups in any four-carbon subchain are on the same side (gauche) or opposites sides (trans) of the plane of the middle carbon-carbon bond. A gauche conformer (rotamer) is thus a state of maximum potential energy, whereas a trans conformer is a state with minimum potential energy. The difference between these states has been found to be approximately 0.5 to 0.8 kcal/mole (Mead et al., 1986). The relative number of butane molecules present as gauche conformers with respect to trans conformers can be calculated from the Boltzmann equation (Mead et al., 1986). At 25° C approximately 66% of the butane molecules are trans rotamers. [ ] However at 100° C, only 33% of butane molecules are trans rotamers. Exposing the hydrocarbon chain to a polar, rather than an a polar, medium should also cause an increase in the number of gauche butylene groups in a hydrocarbon chain, although this effect has been difficult to observe experimentally (Mead et al., 1986). Forming a crystalline hydrocarbon is equivalent to decreasing the temperature, which greatly increases the amount of trans butylene groups present in the chain. From the preceding discussion, a picture of the solution species of concern can be developed. The collector monomer should exhibit the greatest number of gauche rotamers and most likely will look crumpled or balled-up to reduce the surface area in contact with water. The micellar form is expected to be aggregated, with the hydrocarbon chain existing in a less polar environment. These characteristic conformational features have been examined by FT-IR spectroscopy for various liquid phases of alkanoic acids (Umemura et al., 1981; Cameron et al., 1982a; Yang et al., 1986; Wong, 1987; Wong and Mantsch, 1983; Cross et al., 1992), phospholipid membranes (Fringe Ii, 1980; Casal and Mantsch, 1985: Wong et al.. 1988;

Jan 1, 1994

By Donn A. Calder, Wayne C. Henderson

The Calmet Process for extraction and recovery of gold and silver from concentrates and high:grade ores has been a commercial reality for over two years. During that time period, almost seventy-five different concentrate (or ore) types have been processed in approximately 200 separate lots (a total of almost 2000 short tons). During commercial operation of the process at the plant in Fountain, Colorado, recovery of gold and silver into <lore' has averaged almost 93% for gold (range 81-98%) and over 90% for silver (range 76-97%) based on a fire assay target and calculated head values.

Jan 1, 1998

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth&apos;s surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth&apos;s surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET&apos;s uranium exploration procedures.

Jan 1, 1981

By Geoffrey Purcell

The flotation response to amine collector of quartz and the feldspars microcline and albite, of the pyroxenes augite and spodumene, and of olivine can be, explained by a physical adsorption model. Flotation decreases in the order given above, and the different behavior of the three groups is attributed to structural variations of the silicates, With sulfonate collector both chemical action and physical adsorption play their part in producing hydrophobic surfaces, and flotation increases in the order given.

Jan 1, 1966

By David A. Lindsey

In this paper, we present a physiographic classification of gravel deposits, identify some field measures of aggregate quality, and describe sampling strategies for mapping aggregate quality in the Front Range Urban Corridor of Colorado. Gravel occurs in four types of deposits along the Front Range of Colorado: (1) piedmont alluvial fans, (2) high dissected terraces, (3) high (continuous) terraces, and (4) floodplains and low terraces. The four deposit types are the basis for definition of gravel-deposit models, which differ in geologic environment, deposit characteristics, deposit size, environmental impacts of mining, and post-mining use. Of the four types, floodplains and low-terrace deposits have been exploited most for gravel. High terraces also have been mined. Deposits of high dissected terraces and dissected alluvial fans have produced minor amounts of gravel, mostly for use as local fill. Studies to identify useful field measures of aggregate quality and to determine the appropriate scale for sampling were conducted on gravel deposits beneath the flood-plain and low terraces of the South Platte River north of Denver and the Cache la Poudre River between Ft. Collins and Greeley. Gravel deposits of the South Platte were selected for study because they represent the last major resource of gravel for aggregate in the Denver metropolitan area. The Cache la Poudre valley is the primary source of gravel aggregate for rapidly urbanizing areas around Ft. Collins and Greeley. Of all the field measures of gravel quality, the most important is particle size. Various parameters that measure particle size were investigated, but the easiest to determine, and the most useful to the aggregate industry, are measures of the proportion of coarse sizes. Particle size varies widely in gravels of the urban corridor. Gravel lithology, particularly the presence of deleterious particles such as reactive volcanic rocks and decomposed rocks, must be determined to assess aggregate quality. Studies of South Platte and Cache la Poudre gravels have not revealed large proportions of deleterious lithologies. Studies of particle shape revealed only small numbers of physically weak shapes in both the South Platte and Cache la Poudre gravels. Particle shape does not appear to vary from place to place in the gravels. Rounding, or the ab¬sence of angular corners, may play a role in the tendency of loose gravel to yield under load. South Platte and Cache la Poudre gravels are rounded, and rounding tends to increase upstream. Before the quality of gravel in a valley can be assessed, the stratigraphy of the gravel must be known because it affects sample design. If only a single gravel layer is to be studied, only the thickness of the gravel must be known before sampling. If, however, more than one layer of gravel-distinguished by particle size, sorting, or lithology-is present, sampling must take into account the thickness and distribution of each layer. For example, three gravel layers of different particle size underlie the floodplain and low terraces of the South Platte. The tributary Cache la Poudre, on the other hand, contains gravel layers that can be distinguished only locally and vary slightly in particle size. Sampling experiments were conducted on gravel bars in the South Platte River and in gravel pits on the floodplain and low terraces of the South Platte and Cache la Poudre Rivers. Experimental results indicate that, even where sample error is large, regional and stratigraphic variation may be measured if it is large relative to sample error. Using vertical trench samples weighing an average of 40-90 pounds, down-stream decrease in coarse particle size was mapped for Cache la Poudre gravel, and differences among superposed gravel beds were measured for South Platte gravel.

Jan 1, 1999

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By Eberhard Werner

Existing reports on the effects of mine subsidence on water wells and springs appear to be inconsistent. Some report quick and complete recoveries to pre-mining conditions while others indicate long-term or permanent effects. It is clear that topographic and geological factors as well as precise position with regard to the mine are important in determining probable effects of subsidence on aquifers. Ridgetop aquifers which are well above regional base-level are much more susceptible to disturbance by mining activities than those located topographically lower. Effects seen are attributed largely to increased permeability, both horizontal and vertical. of the aquifer rocks. The deeper aquifers usually show short term losses or water-table declines. but the effects on the ridge-top aquifers persist for longer periods or may be permanent. Subsidence enhances permeability. so that infiltrating water moves much faster to lower levels. causing pond and stream losses and declining levels in wells as well as declining flows of springs of the higher aquifers, while increasing levels and flows of the lower aquifers. Additional effects are shifts of spring locations caused by minor tilts due to differential subsidence and redirection of shallow flows by changes of horizontal fracture permeability. These effects are seen as mining of a panel progresses beneath the site. and are often repeated when adjacent panel mining fronts pass the site. Analysis of water well level and spring flow records indicates that the effects are greatest at the edges of longwall panels in the tensional regime. These effects are amplified for locations close to topographically steep terrain and in close proximity to fracture traces mapped from medium-to small-scale aerial images.

Jan 1, 1986

By Scott G. Britton

Until now, only the range of typical construction projects which are repeated over and over during the life of a coal mine have been discussed. This chapter looks at underground construction projects which occur only once or twice during the life of any given mine and are major construction projects in both time and cost. These projects usually require the services of an outside engineering and construction firm with hands- on experience in design installation. Because of this involvement with engineering and construction firms (EIC), the role of the construction engineer will change from one of actively de- signing and directing tasks to one of planning, inspection, and quality control. To reflect this role change in the discussions, the focus of this chapter will be changed to a broad overview of project participation. Of course, the projects under consideration in this chapter could easily fill more than one book on their design and installation. In addition, major construction projects are extremely site specific, requiring months of data collection about site geology, physical conditions, and potential excavation and construction requirements. Therefore, no attempt shall be made to discuss any detailed construction aspects as was done in earlier chapters. The purpose of this chapter is to present the fundamental concerns of a staff engineer or supervisor. This engineer does not make the decisions on choosing the EIC firm, but assists and interacts with their project team to accomplish the goals set forth by higher management. The construction topics to be reviewed fall into three main categories. The first category is highlighted by the installation of a main surge bin; the second is typified by the construction of an underground shop; and the third category encompasses special projects such as rotary dumps, crusher stations, and foremen&apos;s offices. These categories highlight the differences between degrees of mine responsibilities for project completion. The first topic is usually a turnkey project by an E/C firm for a given mine. The second topic represents the leading role of the mine in the project with a contractor as a support service or equipment supplier only. The third topic, special projects, is an example of a joint venture-between a contractor (leading partner) and mine management. These roles can change with any given project, but the changes in management responsibilities for the construction engineer can be nicely illustrated for the purposes of this text. The first step toward constructing major mine projects is to analyze the mine which influence their design. From the mine management standpoint, these parameters should reflect the role the mine will play in the project construction. In other words, what is the nature of the proposed mine environment and what are the material, labor, and time requirements needed to assist or direct the chosen engineering and construction firm? Answering these questions requires some basic project planning and cost estimation work. Here, only a general treatment is necessary, since detailed discussions of these topics will follow in Chapters 8 and 10. For those persons interested in the role of the EIC contractor, I suggest beginning by reviewing the article by Beall, "The Role of an Engineering and Construction Contractor," presented in the October 1980 issue of Mining Engineering magazine.

Jan 1, 1983

By Jodie Robertson, Isabel Barton, Cristian Caro

Prior to mining, all rocks contained in a mineral deposit must be placed in one of several categories known as ore types. Each ore type describes a different way that the rock will behave in processing. The ore type determines which process stream a particular mined unit will be sent to, sets expectations for process engineers and metallurgists, and forms the basis for recovery predictions and production estimates. At first, ore types are assigned mainly by geologists based on visible geological criteria (dominant ore mineralogy, estimated grade, rock type, alteration type). As metallurgical tests are carried out and process data accumulate, the resulting criteria may be factored into the ore typing process, typically as assays and recoverable metal using the relevant process(es). Other variables may also be incorporated into ore typing at operations if they are particularly important, such as grindability, preg-robbing, gangue reagent consumption, and the presence of especially deleterious minerals such as talc or smectite. The mine operation department may also redefine ore types and/or process destinations based on economic criteria. A “best” ore type is designated that (in theory) best describes how the rock will behave in processing. Codes representing this ore type are entered into the drill-hole database, then interpreted on cross sections and level plans, and finally added to the block model. Ore types are iteratively reexamined and adjusted over the life of a project. Major difficulties in effective ore typing are (1) lack of communication between geologists and metallurgists, (2) the imprecision inherent in imposing clean categories on messy natural systems without discrete divisions, (3) the need for ore types to provide useful information for a wide range of processes, (4) difficulties in scaling up laboratory test results to mine production, and (5) conflict among geological, metallurgical, and economic criteria for ore typing.

Jul 1, 2024