Search Documents

By Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

Ground deformations are of major concern during tunneling, especially in downtown environments, since they have a significant impact on the costs and practicality of tunneling. This case history describes soil and groundwater conditions and ground behavior during the construction of twin transit tunnels for the Downtown Seattle Transit Project (DSTP). The tunnels were excavated through complex glacial soils ranging from hard glaciomarine drift to flowing sand. The tunneling process was greatly facilitated by the prediction of soil layer positions to an accuracy of ±0.6 m (2 ft). Tunneling was complicated by the presence of over 500 temporary tiebacks and by disturbed ground overlying an operating railroad tunnel. A variety of ground improvement techniques were used to successfully minimize settlements, which ranged from 1 cm (0.4 in.) in glaciomarine drift to 6 cm (2.4 in.) in flowing sands. Ground improvement techniques included compaction grouting, chemical grouting, jet grouting, and eductor well systems.

Jan 1, 1991

By D. M. Larsen, K. R. Gardner, P. B. Altringer

The Bureau of Mines, U.S. Department of the Interior, is conducting batch and small- scale continuous laboratory studies on the biologically assisted removal of selenium from process waste waters. Mixed cultures of gram- negative bacteria isolated from several brackish water marshes are capable of reducing selenate [Se(VI)I to selenite [Se(IV)I and precipitating an amorphous elemental selenium product. Selenium extractions ranged from 80 to 96% regardless of the initial selenium concentration. The conditions for rapid bacterial growth and reactor design for optimal selenium removal have been investigated. The mechanisms of bacterial reduction and the rate of selenium removal for scaleup to larger systems is discussed.

Jan 1, 1989

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By T. P. Weldum, B. J. Mahoski, R. S. Rasmussen

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After an overall review of the flow-sheet, two operating circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modeling system, and, on this basis, a quality-assurance program for data gathering was implemented. A number of circuit-design and operating variables were investigated. Statistical analysis of plant-test results revealed relationships previously unquantifiable by any other modeling technique. Improvements in the classification system and in mill grinding efficiencies were demonstrated. As a result, there was significant energy cost savings.

Jan 1, 2000

By Zhen-lu Zhao

The manipulators possibly used in underground mining must deal with unpredictable obstacle while keeping certain positions and orientations of end effector, and in some cases, are required to possess redundant joints in order to be more flexible. This kind of manipulators might be fitted with jumbo drill or platform as auxiliary to potentially deal with some utility works in versatile way, such as installing rock bolts, guniting, blasting, charging, surveys and measuring work, etc.. This paper describes numerical procedures of performing inverse kinematic problems for redundant manipulators .The procedures, based on the generalized pseudoinverse of Jacobian matrix, are developed to lead to kinematic solution at both singularity and ill conditioning, and to guarantee continuous sequence of positions of the end effect or. Furthermore, the solution to optimization and obstacle avoidance is investigated. A numerical example is shown to illustrate the approach.

Jan 1, 1989

By S. Zaman, John Bulter, M. E. Defoe, Franklin T. Davis

This section deals with the carbon minerals and materials: graphite, tar sands, gilsonite, and diamond. as well as sulfur and the sulfides of mercury, arsenic, antimony, and bismuth. Table I contains the production figures for each of these commodities in the United States and in the world. Specifications for concentrates are also summarized as are prices for concentrates at the time the section was written. In each chapter an attempt has teen made to describe the more common commercial mineral involved with the commodity, the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985

By S. K. Kawatra

For efficient control of particle size in a wet grinding circuit, three alternative methods for monitoring pro- duct particle size are available. These methods are based on: 1. Ultrasonic wave absorption. 2. Low-angle forward scattering of a laser beam. 3. Inferential sizing techniques. The relative advantages and disadvantages of each technique are discussed. A particle size monitor can be used on a single grinding line to control the product particle size. To minimize the number of particle size monitors at an operation consisting of many similar grinding lines, a portable multi-stream on-line analyzer can be used. The paper outlines the design and the operational characteristics of the portable multi-stream online analyzer.

Jan 1, 1979

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A low-temperature-chlorination selective oxidation followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide was investigated for hydrometallurgical processing of a chalcopyrite concentrate. In this article, the selective oxidation phase of the process is described. The selective oxidation requires a temperature well above the CuCl-FeCl3 eutectic points. The test procedure was developed with a batch reactor and then tested with a continuous reactor. The process was initiated by adding small amounts of chlorinated samples to a fluidizing bed of dead-roasted sulfide concentrate micropellets. The selectively oxidized samples thus prepared were shown to fully dissolve copper, while virtually all the iron remained undissolved.

Jan 1, 2000

The declining grades of surface deposits have re-confirmed the need for greater production rates. Large scale production requires increased investments in expensive and sophisticated equipment. The key to successful operations can depend entirely on proper equipment utilisation and in this program of research at the Department of Mining and Metallurgical Engineering, University of Queensland, much emphasis has been placed on the analysis and improvement of this aspect of a load-haul-dump operation. For a model to be successfully integrated into a mine engineering function and readily accepted by mine operating personnel, it has to offer more than just results. The concepts used in its design and construction must include sufficient detail to enable engineers to apply it usefully and with confidence.

Jan 1, 1979

By Y. Ooishi, Y. Matsumoto, T. Arai, H. Ohta

The multi-circular face shield (MFS) is a new type of tunnelling machine for construction of the special cross section and has been put to practical use in 1988. The MF shield has two circular faces partially overlapped in a single shield machine and can construct the cross section shaped like glasses for the double track railway. And it is possible to equip two or more cicular faces horizontally or vertically, if necessary. During the development of the MF shield the experiments have been carried out for the purpose of estimating the excavatability and the face stability of the MF shield. As a result it was confirmed that the both types of MF shield (one with double faces aligned horizontally and the other with double faces aligned vertically) has higher performance in the face stability and lower value in the cutter torque and the total thrust than the conventional circular shield.

Jan 1, 1991

By D. M. Muir

Thiosulfate offers a nontoxic alternative to cyanide for processing gold ores. The mechanism of leaching gold using ammoniacal thiosulfate solution is driven by the Cu(II)-Cu(I) redox couple and is complicated by competing ligands such as NH3 and S2O32; It is shown that an understanding of the copper speciation and sulfur speciation is required to optimize this system. This paper presents Eh-pH and speciation diagrams for varying concentrations of Cu(II), S2O32- and NH3 and discusses the conditions under which various copper and sulfur species are stable.

Jan 1, 2002

By William P. Blacutt

This paper examines Bolivia's General Environmental Bill recently passed by Congress: a multi-purpose law with two primary objectives: a) the protection and conservation of the environment, and b) the promotion of sustainable development. In this law, environmental benefits are emphasized by stating general principles, not by attempting to define the means. Regulations are left to the writing of subsequent complementary codes. This paper shows that much of the controversy surrounding the legislation disappears when it is seen as guide rather than an operational part of Bolivia's industrial policy. In essence, the law addresses recent environmental awareness in a region more anxious than ever to speed economic growth.

Jan 1, 1992

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992

By Julie Mitchell

The U.S. Bureau of Mines is conducting research on the application of expert sys tens technology to mining equipment diagnostics and predictive maintenance, to increase mining productivity and efficiency. One of the greatest hindrances to mining productivity is the breakdown of equipment, causing lengthy and costly delays. A diagnostic maintenance expert system (DIMES) is being developed for the hydraulic system of a continuous coal mining machine. Through the use of such a system, the frequency of equipment failures and repair time should be significantly reduced. This paper describes the application domain, the functional requirements, and the problem approach for DIMES, the design and implement at i on of the knowledge- based system, the sensor work involved with the project, and the future plans for the continued development of this and other expert systems.

Jan 1, 1989

By L. Darkwah

The use of explosives in coal mining inevitably results in oversize, midsize and undersize (fines) products due to fragmentation. The oversize can be broken into smaller sizes by further processing. However, the undersize have a negative affect on the efficiency of a mining operation. Therefore, limiting the amount of fines can be economically crucial. This paper concerns investigations aimed at reducing fines generation in coal mining. Inherent fractures were identified as one of sources of fines generation. This paper is centered on establishing a relationship between the fracture occurrence, the explosive properties and the blast outputs, which are evaluated in terms of the fines generated.

Jan 1, 1998

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By W. D. Diment

The concept of flying employees in and out of remote mine sites on a regular rotation basis, rather than establishing permanent support communities nearby, has gained increasing acceptance by mine operators, unions and regulatory agencies in Canada. The development of successful fly in/fly out programs and resultant compressed work schedules is dependent on meeting design requirements through comprehensive research of worker profiles to ensure the selection of suitable employees and the implementation of satisfactory working conditions. This paper presents an overview of Canadian mine industry practice with regard to the fly in/fly out mode of operation and compressed work schedules.

Jan 1, 1987

By R. A. Bauer

Investigations of bedrock within subsided areas over abandoned coal mines in Illinois reveal very little disturbance of the bedrock. In areas that have surface subsidence of 0.3 to 1 m (1 to 3.25 ft), examination of cores from exploration drilling and investigations of the boreholes by means of closed circuit television have shown that fractures are spaced at least 0.9 to 3.6 m (3 to 12 ft) apart. They are located within a zone 6 to 15 m (20 to 50 ft) above the collapsed area in coal mines 42.6 to 112.7 m (140 to 370 ft) deep. The dip of the fractures ranges from 25° to 60°, cutting across nearly horizontal sedimentary bedding planes. The amount of fracturing found in the collapsed area decreased as the amount of soft, weak materials increased in the immediate overburden of the mine.

Jan 1, 1987

By T. S. Golosinski

Most of the 154 t (170 st) truck fleets that were predominant in large surface mines in the 1970s and 1980s are approaching the end of their economic life. One replacement option considered by mine operators is a change to the 2 18 t (240 st) trucks. A comparison of load capacities between the 1.54 t (170 st) and the 2 18 t (240 st) trucks indicates a large productivity advantage in favor of the 218 t (240 st) trucks. This advantage, however, is often reduced by a number of site-specific factors. Therefore, a careful evaluation is required to define the actual benefit of changing to the large trucks. This article discusses some important factors that have an impact on truck size selection, based on several different studies. 218 t (240 st) trucks The 2 18 t (240 st) rear dump trucks were first introduced for surface mine service almost 10 years ago. However, it is only during the last few years that this equipment has gained acceptance in the surface mining industry. About 250 units were employed in surface mines worldwide at the beginning of 1992, and further purchase commitments are being made. Encouraged by the mining industry’s interest, all major off-highway mining truck manufacturers now offer 218 t (240 st) models (Table 1). At present, the existing 218 t (240 st) truck fleets are dominated by electric drive trucks. However, recent introduction of a 2 18 t (240 st) mechanical drive truck rounds out the development of this truck size.

Jan 1, 1992

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982