Search Documents

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low-, a medium-, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0 percent ash, as follows: From low-volatile anthracite, 0.7 percent; from medium-volatile coal, 1.0 percent; and from high-volatile coal, 2.3 percent. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0 percent or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a conventional dense-media washing plant.

Jan 1, 1968

By David G. Thompson

There are basically two commonly used methods of drying washed coal. They are mechanical drying (sometimes called dewatering) and thermal drying. The common methods of mechanical drying are by using vibrating screens, cross flow screens, sieve screens or Vor-Siv, vacuum filters and centrifugal dryers. With thermal drying, the common types include direct fired fluid bed, rotary drum, flash or suspension, vertical tray or cascade continuous carrier or vibrating fluid bed dryers and hollow screw dryers. In the past, it has more or less been a general rule that any time the total product is being washed, both mechanical and thermal drying was required. The reason for this was that a product moisture of 3 to 4% was required and thermal drying was and is the only practical method by which this can be accomplished. With the advent of air pollution controls and the ever increasing concentration on dust elimination, a 3 to 4% moisture product is no longer practical in either the preparation plant or in the processing plants which utilize the coal. Under the new standards, it is desirable to have a product with a 6.5 to 7% surface moisture. With this moisture range, dusting, due to handling, will bc kept at a minimum.

Jan 1, 1975

By Issac Douglas, Sheila Devasahayam, John S. Thella, Manoj K. Mohanty, Jeremy Prishmont

The flotation performance of Sodium O, O-diisobutyl Di thiophosphate (referred to as reagent A) was compared with Aerophine 3418A (referred to as reagent B) for floating a complex copper ore grab sample (Ore A). Preliminary test results indicated a cumulative copper concentrate grade of 10.19% with a recovery of 86.31%, which was achieved with reagent A from a feed consisting of 5.32% Cu. The grade and recovery achieved using reagent B are 9.11% and 87.85%, respectively. A comparative analysis based on the preliminary test results indicated that reagent A’s performance is better than that of reagent B at lower concentrate grades, specifically below 12% Cu. However, the flotation performance is better for reagent B at higher concentrate grades (>12% Cu). A more detailed study was conducted to optimize the grade-recovery performances achievable from both reagents on a complex low-grade copper ore sample (Ore B) from Western USA. Test results indicated a copper concentrate with a grade of 5.5% Cu and 78.59% recovery was obtained with reagent A compared to 4.31% Cu and 62.04% recovery with reagent B from a feed consisting of around 0.25% Cu.

Feb 22, 2026

By Corey Vaughan

Unplanned shutdowns from abrasive wear part failure in crushers, chutes, and slurry pipe assets can cost millions in lost production and reactive maintenance. 2Censor patented sensor technology enables real time abrasive wear monitoring of mineral processing equipment, turning passive assets into smart, data driven components. Wireless sensors embedded in liners and pipework transmit wear data live to operators, allowing for predictive maintenance, safer scheduling, and optimized asset life. This paper will present global case studies showing reductions in downtime, increased throughput, and improved maintenance accuracy. The system is ready to retrofit, neutral to original equipment manufacturers, and proven across more than twelve countries in abrasive wear liners and slurry pipe applications.

Feb 22, 2026

By C. W. Schultz

The distribution of material passing a screen, or a set of screens, is described by the equation [ ] where p = the probability that a single particle will pass the screen on a single presentation k = number of layers of screen cloth n = distance from head of screen expressed as number of screen openings. This model can be used to predict the performance of conventional screening operations (i.e., k = 1) as well as the so-called "statistical screening" operations. Using this technique, in which multiple identical layers of screen cloth are employed, screening can be carried out at a finer size than is possible with conventional techniques with no loss of separation efficiency.

Jan 1, 1969

By T. Reed Scollon

Before we can attempt to answer the question of what can be expected from coal research, let us examine why research is done in other fields and what others expect for the money they spend on research and development. Up to 1900 almost all organized research was carried out at universities. Most of the support came from the university, and by present standards the amount of research was extremely small. The motivation for university research was basically discovery of new phenomena, with the objective of advancing knowledge. Side by, side with this organized effort was that of individual inventors who were primarily responsible for applying this new-found knowledge to useful purposes. During this period inventors were rarely supported by anyone, and experimentation was carried out either in their spare time or at the expense of earning a living. Men like Edison, I believe, were the first to demonstrate on a large scale that one could systematically apply newly discovered scientific principles to inventions that would serve useful purposes and would return a profit to those engaged in the effort. The tremendous expansion in research therefore began with the realization and demonstration that the scientific discovered could be applied in such a way as to return a' handsome profit to those who invested in it. The motivation of many of the research personnel however, remained the satisfaction associated with new discoveries, The money to support their efforts came from those interested in a return on their investments. Since the First World War and a rapidly accelerating rate since the Second World War another important motive for supporting research has appeared--the needs associated with national defense; this type of research has been supported almost exclusively by the Government.

Jan 1, 1959

By G. Chancellor

"INTRODUCTION The paste plant is located at the Barrick Goldstrike mine in Northern Nevada on the Carlin Trend. The Goldstrike property consists of an open pit and an underground mine; along with two processing facilities: a roaster and an autoclave. The underground portion of the mine produces approximately 1,800,000 ore tons per year and approximately 400,000 ounces. The mine is broken up into four distinct zones: Banshee, Meikle, Rodeo and Northpost. The current paste plant services both the Rodeo and Northpost zones. Development of the conceptual designs and permit approval for this plant was an extensive process that took over a decade to complete. A testing program was developed in conjunction with this process and implemented throughout to ensure the following metrics were achieved: ensure no environmental impact, material available onsite would be able to flow through the pipe to all required locations, and that this material could achieve the appropriate final strength. PLANT AND UNDERGROUND CONSTRUCTION This is the first paste plant to be built in Nevada. The paste plant at Goldstrike began construction in January 2012 and was completed in March of 2013. This plant was constructed to service the Rodeo side of the underground mine which previously utilized a cemented rock fill (CFR) plant to meet their backfill needs. However, in March of 2013, the same month the plant was commissioned, the raise that fed this CRF plant was mined out in a planned phase of the adjacent open pit. This made the switch to paste all the more difficult as it was being relied on for as the sole source of backfill production even though the system yet to be fully tested and optimized. The plant was designed to be fed with onsite Roaster tailing which would be thickened and then mixed with cement and fly ash. The plant was designed to pump 177 tons of paste per hour with a utilization of 65%. The original design specifications for the paste were 77% solids with varying binder contents depending on where the paste was being placed"

Jan 1, 2015

By T. P. Meloy

Riffles on a shaking table have a major effect on particle separation. This effect is modeled in a spreadsheet.

Jan 1, 1993

By P. T. Bissert, J. P. Ducarme, J. D. Noll, C. C. Jobes

"There have been about 42 fatalities in underground coal mines between 1984 and 2015 where the victim was struck, pinned, or run over by a mobile machine (MM) such as a shuttle car, scoop, or battery hauler. MSHA has issued a proposed rule requiring proximity detection systems (PDS) on MMs in an effort to prevent future fatalities. Currently approved PDSs use electromagnetic (EM) technology to detect the presence of a miner and impose machine controls to prevent contact. The disadvantages of an EM-based PDS on MMs include the need for a miner-wearable component (MWC), environmental interferences, EM interferences from other devices, and low localization range and accuracy. NIOSH researchers are investigating alternate technologies that could improve the capabilities of the current PDSs. Many technologies were reviewed, and NIOSH researchers identified RFID, LIDAR, RADAR, ultrasonic detection, and computer vision as candidates for PDS development. The performance characteristics of each technology and its applicability to an underground mining environment will be discussed, along with international developments and implementations, and the concept of sensor fusion. INTRODUCTION PDSs provide safety to mine workers by detecting their presence (and in some cases location) around a machine. These PDSs provide a warning zone, which triggers an alarm, and a stop zone, which halts the machine before it contacts the miner. The Mine Safety and Health Administration (MSHA) issued a final rule requiring that PDSs be installed on all continuous mining machines (CMMs) on the working section, with the exception of full-faced machines, according to a phase-in schedule for newly manufactured and existing equipment [1]. The PDSs that were designed for CMMs have since been adapted to other mobile machines. Mobile machines include scoops, which are used as general utility vehicles, as well as coal hauling machines, such as shuttle cars, ram cars, and continuous haulage systems. MSHA has examined all accident reports from 1984 to 2014, and determined that 42 fatalities could have been prevented on mobile machines had a PDS been installed [2]. As such, MSHA issued a proposed rule that would require mobile machines on working sections (with the exception of longwall sections) to be equipped with a PDS. This rule would follow a phase-in schedule for newly manufactured and existing equipment. Currently available PDSs are based on electromagnetic (EM) technology. NIOSH researchers developed a shell-based magnetic flux density distribution model [3] for determining the position of a miner near a machine. A typical system would consist of four generators positioned around the perimeter of the machine. Each generator is a coil of insulated wire wrapped around a ferrite core. The magnetic field strength is proportional to the current running through the coil. Miners working on the section have an MWC, which is a transceiver that measures the field strength emitted by the generators and transmits a data packet over an RF link which contains the field strength reading to the PDS controller mounted on the machine. The magnetic field generators are pulsed sequentially such that the MWC can identify which generator’s field strength it is reading. This type of system utilizes the principle of magnetic flux density: the closer the MWC is to the field generators, the higher the field strength reading. Thus a miner’s presence can be determined once he gets too close to the machine, because his MWC will measure a magnetic flux density beyond a certain threshold. These thresholds are utilized on a per-generator basis to “shape” the fields for both warning and stop zones around a machine, as illustrated in Figure 1."

Jan 1, 2017

1. Theory of Wet Dust Suppression Techniques Wet dust suppression is the utilization of a liquid for the control, reduction or elimination of airborne dust, or the suppression of such dust at its source. Effective control involves: a. The confinement of the dust within the dust producing area by a curtain of moisture. b. The wetting of the dust by direct contact between the particles and droplets of moisture. c. The formation of agglomerates too heavy to remain airborne, by combining small dust particles with each other and with the droplets of liquid. From the standpoint of economy, availability and safety, water is the ideal fluid. From the standpoint of effectiveness, however, it leaves much to be desired. As a result, a tech¬nique has been devised in which very small percentages of specially formulated dust control compounds are blended with water to greatly enhance its dust suppression qualities. The terms "dust control compounds, wetting agents and surface active agents" are frequently used interchangeably. Although dust control compounds represent a specific type of wetting agent, a great many wetting agents are far from satisfactory for dust control. "Wetting Agents" is a broad category which covers such items as emulsifiers, solubilizers, detergents, foamers, penetrants, thickeners, etc. Dust control compounds, on the other hand, are carefully formulated blends in which one or more special surface active agents have been incorporated.

Jan 1, 1972

By John S. Cummings

In this paper the phrase "exploration for blind metal deposits" refers to exploration activities geared to the discovery of metal deposits which cannot be located by visual surface inspection. The word "system" refers to all of the components (people, money, corporations, techniques, etc.) which collectively result in an exploration process. The details of the system or systems which I have employed in exploration will not be discussed because of client relationships. However, some of the more severe problems in exploration result from how the system's components interact and our attitudes as to what exploration data is telling us, if anything. It is these items which will be discussed. Exploration for blind metal deposits, which has been relatively intense over the last 2S years compared to rather minor outlays prior to World War II has often been an uncoordinated assortment of various specialists employing various techniques (see Dickerson -1). In a program geared to the location of blind deposits, the lack of outcropping deposits or occurrences should not be a deterrent to a well conceived and well planned program. The severe cyclical swings in exploration activity, although often coinciding with depressed metal prices, by and large result from the failure of exploration operators to present a coherent and realistic program to management. It is my opinion that the stream of complaints criticizing management for cyclical exploration support are mostly unwarranted, as many of the programs and goals are ill defined. Although depressed market conditions may serve as the catalyst for exploration cuts, the underlying cause is that when the "chips are down", the non-directional, non-specific nature of many programs is revealed. Thus management should not be castigated for eliminating such programs during bad times, but rather they should be castigated for supporting them during boom periods.

Jan 1, 1978

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By T. D. Kaufmann

When Dr. David Gully solicited this paper last spring a few questions basic to commodity trade between the U.S. and world markets appeared perplexing. Why, for example, when the demand for aluminum was at a peak and when little expansion of capacity had taken place, was the dollar price half of what it had been at the previous peak? Or, why in 1984 when imports surged by 50% as the U.S. economy pulled out of its recession did the dollar not fall, but rather rose by 35%? And, why when the experts all seemed to agree that the dollar was grossly overvalued did the price of gold continue to decline? Surely these were extraordinary times for the mineral economist. When this paper was written in late July, 1985 the answers seemed clearer. The prices of many commodities were not low - the dollar in which they were denominated was too high. In other currencies many commodity prices were indeed high. The dollar was overvalued in trade terms by some 40% caused by an influx of short term coupon investments made by foreign money managers to take advantage of the higher short term interest rates in the U.S. relative to other international banking centers. With a decline in the relative difference in interest rates, an unhealthy buildup of foreign bank accounts and a perception that the dollar would fall, the dollar did start to decline rapidly.

Jan 1, 1985

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

By C. W. Schultz

Earlier publications from The University of Alabama have indicated that column flotation performance is improved when operating at low pulp levels and when the feed is directed into the froth phase. To validate these early observations a series of tests were performed in which the position of the feed entry to the column and the pulp-froth interface were systematically varied. The optimum grade-recovery relationship was achieved with high feed entry (WA) of column height) and very low pulp levels (<10% of column height). The position of the pulp-froth interface appears to be the more critical variable. When operating in this mode (1. e. at low pulp levels) column flotation becomes. in reality. a froth separation process.

Jan 1, 1991

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By V. O. Tenorio, A. M. Sanzana

"INTRODUCTION This report summarizes a research about mines which are transitioning from surface to underground mines. It is a guide to make strategic decision in these increasing amount of mines. Capital and operating costs are linked with major strategic decisions in the exploitation of an ore body. This is the reason to analyze costs related to this transitioning world trend. There are multiple reasons for transitioning from Open-Pit (OP) to Underground (UG) mining. The primary economic incentive for going UG is that the cost per unit of ore from OP mining eventually exceeds that from UG extraction. This is due to the excessive amount of waste that must be extracted when the depth of the pit increases. In addition, the reduced footprint of UG operations contributes to diminish the environmental impact on the surface. Furthermore, it becomes more difficult to find new, easily accessible ore deposits. Then, a cost model helps to guide strategic decisions in the transition from OP-to-UG mines. Objectives • Propose a methodology to guide strategic decisions in the transition from OP to UG mining. • Create an integrated cost model based on existing OP and UG individual cases. • Identify and characterize a group of mines transitioning from OP to UG. • Analyze operating and capital costs of a particular transitioning from OP to UG mine. MAIN CONCEPTS Open Pit Mining (OP) The main decisions in OP mines are: Cut-off grade, Stripping Ratio (SR), equipment size, stockpiling, pushback sequencing and processing capacity. The stripping ratio is measured as the tonnage of waste required to be removed to reach and extract one tonne of ore. The material extracted from an OP exploitation can be classified as waste and ore. This classification depends on the cut-off grade. The cut-off grade indicates the minimum amount of material with economic value in a block. The waste from the mine is going to the waste dump and the ore is going to stockpiles where will be store and then going to the processing plant (leaching or concentrator). The waste of this process is going to the tailing pond big pools. And the product is sell in the market. Another important issue is the mining capacity which is going to define the investment in mining equipment. Underground Mining (UG) The first decision to be made in order to open an underground mine is selecting the mining method. Caving methods are the more productive and have lower operating costs. There are three caving methods: Block Caving (BC), Panel Caving (BC) and Sublevel Caving (BC). The access development could be an horizontal adit or a straight or downspiral decline. A shaft could be used for inclined or vertical access. Other key issues are: equipment capacity, cut-off grade and production sequencing."

Jan 1, 2016

By Lawrence P. Kennedy

The Lynne deposit is a volcanic-to volcaniclastic-hosted, Zn-Pb-Cu-Ag orebody located in the early Proterozoic magmatic terrain of northern Wisconsin. As of February 1991, core drilling has partially delineated a multi-million ton, near-surface, disseminated to massive sulfide deposit. The deposit is hosted by a gently dipping sequence of fragmental rhyolites, felsic tuffs, less abundant dacite to andesite flows, and fine-grained volcanic sediments. The deposit is broadly conformable With the host rock stratigraphy, but the ore zones thicken and coalesce in the central part of the deposit.

Jan 1, 1991

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019