Search Documents

By A. Probst, N. Moores, J. A. Finch

In 1994, McGill University and INCO Ltd. (Sudbury operation) initiated the transfer of technology originally developed to detect levels in equipment ranging from flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud line and the solids load. The probe consisted of a vertical tube with 32 equally spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth to produce a conductivity profile. From the conductivity profile, the mud line and the percent solids can be inferred. The probe was installed in October 1994, and it has been successfully detecting profiles since then. This paper includes a description of the incidents that occurred and the experiences gained during this technology-transfer process. Discussed is probe installation and startup; software modifications to accommodate both operating conditions and the needs of the operators; and calibration procedures to adjust to changes in performance as a consequence of long-term use. Also included are preliminary observations of the still-in-progress last stage, i.e., signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.

Jan 1, 1999

By Hans Breuer

The new regulations for the bituminous coal mining industry, issued by the mining authorities of the Federal Republic of Germany, are aimed at reducing to a feasible minimum any development of the coal workers pneumoconiosis (CWP) by lowering the admissible dust exposure of mine workers. Additional and improved measures of dust suppression and job assignment control *) are required for the purpose In this connection two basically different demands are placed on dust measurements: As far as dust suppression is concerned, the causes of dust development and the effectiveness of methods applied to reduce dust concentrations have to be identified, whereas with regard to the control of job assignment, the dust exposure of mine workers has to be depermined. Demands placed on dust measurements -- specifically for determining dust exposure -- are liable to become more severe since the threshold limit values were considerably reduced in these last years and since any additional dust suppression measures as well as a purposeful job assignment to certain mine workers are dependent on relevant measuring data. Therefore, research work has been carried out with the objective of measuring and evaluating, in terms of their effect (i. e. their incidence on the development of a CWP), size distribution, concentration, and specific noxiousness of any prevailing dust conditions.

Jan 1, 1980

By Bruno Bussière, Michael Aubertin, Robert P. Chapuis

Covers with capillary barrier effects (CCBE) have been used in recent years as gas barriers for the isolation of wastes, including reactive mine tailings. Capillary barrier effects help to maintain a high degree of saturation in the moisture retaining layer, which then reduces gas flux. Various factors affect the degree of saturation of the moisture retaining layer in a CCBE, such as the material water retention characteristics and layer thickness. Slope geometry can also influence the hydrogeological behaviour of a CCBE, but this factor has frequently been ignored in the past. In this paper, the authors show some results of a numerical study that illustrates the influence of slope on the behavior of capillary barriers made of different types of material. The numerical model calculations are based on an actual case of a CCBE constructed in northern Quebec. This investigation shows that the water content profile is greatly affected by the position along the slope. Thus, it is necessary to evaluate the influence of the geometry to properly establish the performance of a cover system.

Jan 1, 2000

By J. A. Oraniscak

Longwall mining operations continue to increase extraction rates and the potential to generate higher amounts of airborne respirable dust (ARD). The National Institute for Occupational Safety and Health (NIOSH) has gathered data from underground longwall surveys and laboratory crushing tests to identify the important factors influencing the amount of ARD levels generated. Coal-seam characteristics, operational parameters (i.e.,cut sequence, mining height, etc.), extraction rates and dust-control parameters (i.e., airflow, water flow, etc.) were examined to determine their influence on ARD levels measured at longwalls during actual mining operations. ARD generated by a laboratory crusher while crushing bituminous coal samples collected from underground longwalls was also examined to determine if there were cor relations with coal-seam properties. Results from the longwall and laboratory data collected indicated that low-ash, high-volatile coals (low moist fuel ratio or MFR coals) generate higher amounts of ARD. It was found that face ventilation and water application to the coal product are essential elements to controlling longwall ARD levels.

Jan 1, 2000

By M. K. Gangal, E. D. Dainty, G. Kunchur

This paper presents a validation of C02 as a single surrogate measurement for other diesel-emitted pollutants in multi-diesel-machine operations typical of small underground mines. This means that the simple measurement of C02 alone can be used to estimate the concentrations of other components of diesel exhaust in the mine environment. The linear relationship of C02 concentration with other diesel-emitted pollutants was indicated by the results of simultaneous real-time monitoring of C02 with CO, NO, NO2, SO2, Respirable Combustible Dust (RCD), and Air Quality Index (AQI) in several small underground mines. The SO2 was not directly measured but calculated from the measured C02 concentration and diesel fuel analysis for carbon, hydrogen and sulphur. The measurements were made in the return air drift under various mining conditions involving a number of diesel LHDs and haulage trucks. The statistical analysis and mathematical representation of the several components of diesel pollutants with C02 are presented. Regression analysis shows that at the 1 percent level of significance there is a strong linear relationship of these diesel pollutants with C02. This relationship is discussed in detail, concluding that C02 measurement alone is a good indicator of overall mine air quality and can be used as a control parameter.

Jan 1, 1991

By A. J. Jeffery

Heat transfer to a fluid flowing through a rough duct has been shown by many researchers to be a function of surface roughness. The effect of roughness asperities on the duct surface is to turbulate the fluid as it flows through the duct, increasing frictional pressure losses and convective heat transfer rates, and also increasing the surface area per unit length available for heat transfer. These factors combine to increase the total costs to the mine in terms of refrigeration and fan power requirements. A measurement system designed to automate the collection of tunnel roughness information and based on an infra-red timed pulse laser has been developed at the Royal School of Mines in London. The system allows accurate, high resolution digital recordings of tunnel surfaces to be made in two or three dimensions. Software for analysing the data has been written, and the description of a complex surface via single numerical term has been explored. A relationship between the numerically measured surface roughness and the pressure loss of the ventilating air is being investigated with a view to establishing an alternative method of describing tunnel roughness. The paper describes the roughness measuring technique developed and the analytical techniques explored so far.

Jan 1, 1993

By F. J. Menzer, E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 91,000 tonnes of ore per day and has copper ore reserves estimated to be in excess of one billion tonnes. Functional groups within the Geology Department (currently staffed with six professional and two support personnel) include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pit metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct exploration and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1992

By P. Eng. Daniel Kelly

INTRODUCTION The Astoria property is located in the prolifically mineralized Abitibi greenstone belt and is one of the most advanced projects presently under development by Yorbeau Resources Inc. This property, which hosts the Astoria gold deposit, is located in the southern part of Rouyn township, Abitibi area, Quebec, 4 km south of the city of Rouyn-Noranda (Figure 1). The Astoria deposit has been the subject of underground development for over a half century, beginning with Granada Rouyn Mining Co. in the 1930's and followed by Astoria Rouyn Mines Ltd. in the 1940's. Yorbeau Resources Inc. acquired the property in 1984 and has, since then, conducted numerous exploration programs on this gold deposit. The diluted reserves of the Astoria deposit are estimated at 1,3 million metric tons grading 6,14 grams of gold per metric ton (1.4 million st at 0.18 oz/st). This reserve figure is based on the results of surface and underground exploration carried out from January 1986 to June 1987 and includes ore in the proven, probable and possible categories. This paper is divided into two sections. The first part includes a summary of the geological environment including a description of the gold bearing zones and a short discussion on wall rock alteration. The second part of this paper reviews the underground work and the objective of the ongoing exploration program.

Jan 1, 1988

By I. Longson

As a longwall coalface advances a caved goaf or waste region is left behind. Air flow takes place through this permeable goaf due to the pressure differentials existing across it and en route this leakage air picks up both heat and moisture. A marked deterioration in climatic conditions occurs in the face area at all points downstream of where this leakage air rejoins the main air-stream. This goaf heat source can make a very significant contribution, typically 30-40% to the rate of total heat pickup on an advancing UK longwall coalface with a VST of 40°C and hence on the climatic conditions that prevail at the return end and in the return gate of the face. The magnitude of the rate of heat collection from the goaf depends on a number of factors but it has been established that it is particularly influenced by the prevailing virgin rock temperature and the total flow rate of the leakage air. This paper proposes a model for the goaf based on a packed bed analogy and other assumptions required in order to evaluate the rate of heat pickup are identified. The outlet condition of the leakage air predicted by the model have been shown to correlate with underground measurements taken for a range of different production patterns with the face cutter at various locations on the face. The sensitivity of these predictions to variations in the input data has been tested and is commented on. At this stage of the development the capabilities and predictive limitations of the model are discussed. Further areas of investigation are suggested in order to improve the predictive ability and to extend the versatility of the model.

Jan 1, 1989

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

By Robert C. Cifelli

INTRODUCTION Background and Objectives Underground coal mining is a vital component of West Virginia's economy. However adverse environmental effects including ground subsidence and aquifer dewatering are often associated with such mining activities. Many families in northern West Virginia still rely on private water wells and springs for domestic water needs. In such areas where underground coal extraction and land subsidence have occurred, a disruption of the ground water flow system commonly exists with subsequent drainage of water to lower levels that may extent as deep as the mine workings; this causes loss of water supplies to landowners and represents a nuisance to mining companies 2 This report represents a summary of an M. S. thesis project in geology at West Virginia University by the senior author (3). The intent for this study was to document the effects of underground coal removal on ground water levels at selected mine sites in northern West Virginia, as observed from water wells, springs, and streams. This research should be useful to coal companies and regulatory agencies and aid in recommendations of future water well locations and specifications in areas of existing or proposed underground coal mines.

Jan 1, 1986

By K. H. McDaniel

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ventilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen graphics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1997

By S. P. Mehrotra

In this review article, various approaches and mathematical models that have been used to simulate, design, and synthesize flotation circuits are examined. First, a brief review of flotation kinetics is presented which is followed by a discussion on simulation of flotation circuits. The existing literature on optimal design of flotation circuits has been divided into two broad categories. In the first category, a generalized integral approach is used wherein the optimal circuit design involves determination of both optimal interconnection of various flotation cells/ banks of cells in terms of structural parameters and optimal values of various operating parameters. In the second category, a conventional circuit configuration is assumed to be the best configuration; the optimal design here only means the optimization of operating parameters. The merits and demerits of these two approaches are discussed.

Jan 1, 1987

By John W. Wilson

INTRODUCTION In the past, the cost and time required for the construction of shafts has played an important part in the planning of underground mines. For reasons that are discussed later, the economics and technology of shaft construction in the future can be expected to play an even greater role in the planning of new mines and the operation of existing mines. Indeed, the very feasibility of a proposed mining venture may depend on the cost and timing of the shaft requirements. The most commonly used shaft sinking methods used today for excavating vertical shafts are discussed and the need for new technology and methods emphasized. In one study by the U. S. Bureau of Mines, it was reported that the coal industry in the United States alone could require 170 to 190 new shafts per year on the basis of doubling current production by the mid 1980's or 70 to 90 shafts on a more moderate coal production expansion program. This study concluded that the attainment of the required number of shafts would be unlikely with the present shaft sinking resources and costs. In order to meet the requirements for shafts in the United States coal and metal mining industries, more efficient and speedier shaft construction methods will be necessary. Current shaft sinking methods are, in the main, labor intensive, and it is noteworthy that it is becoming increasingly difficult to attract the work force required to sink shafts conventionally. Because of this situation, some attempts at mechanization have been made to compensate for this ever-increasing scarcity of trained

Jan 1, 1976

By E. Lefeuvre

Precambien in age, the phospate deposit under study which outcrops to the south forms a synclinal consisting of only one mineralized horizon. The synclinal strikes SSW/NNE, dips from 30 to 60 NNE and is about 5 km wide. The deposit has been explored by : - trenches and pits about 50 m apart in the outcropping area ; - core drill holes forming lines perpendicular to the outcrop. These lines are about 100 m apart. On each line, the drill holes are about 50 m apart The phosphate layer is clearly visible and has then been defined from the geologicia1 description of drill hole logs. The layer has been divided into two parts : a very rich, altered part at the hanging wall and a poor part displaying opposite physical characteristics, i.e. a fresh and hard rock. With open pit mining in view, the deposit has been divided into a 3-dimension network of blocks, each block measuring 50 X 50 X 100 m. The tonnages of rich and poor ore, PO25, MgO, Si02, CaO and R2O3 grades and the tonnages of barren waste at the hanging wall and the footwall have been calculated for each block. Given the dip of the phosphate layer ranging from 30 to 60° and its relative thickness (between 10 and 15 m), it was impossible or inappropriate to carry out direct calculation by 3-dimension kriging : too many neighboring blocks to obtain sufficient date and impossibility to draw up the morphology of the layer.

Jan 1, 1986

By d&apos, L. R. Fletcher, Andrea. D. V., M. A. Peltier

The Bureau of Mines analyzed coal mine blasting accident data obtained from the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The data were examined to determine the causes, frequency, and severity of accidents in an effort to point out the most dangerous aspects of coal mine blasting. Accident data for the 14 years from 1971 through 1984 show that there has been a total of 43 fatal and 926 nonfatal blasting accident victims in surface and under- ground coal mining. This is an average of 3.1 fatal and 66.1 non- fatal injuries each year. Underground coal mining accounted for 60.5% of the fatal and 78.7% of the nonfatal accidents involving explosives and breaking agents in coal mining. In addition, since 1970 there have been 53 fatal and 20 nonfatal injuries that occurred when explosives were the ignition source for dust and/or methane explosions in underground mines. Abstracts from 297 accidents that occurred from 1978 through 1984 were also examined to determine accident causes. Most accidents occur during scheduled blasting, and failure of the blast area security system is the leading cause. Blast area security problems in surface mining are failure to clear the blast zone, failure of personnel to follow instructions, inadequate guarding, and failure to retreat to a safe location and/or take adequate cover. Other common causes in surface mining include premature blasts, excessive flyrock, and misfires. In addition to the above causes, accidents in underground coal mining can be due to rockfalls triggered by the blast, unexpected breakthroughs, fumes, and incidents associated with Airdox-type systems.

Jan 1, 1986

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By S. E. Phillipson, S. Romberger

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. The geology of the deposit is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks and an extensive crystal-lithic tuff debris apron. The orebody is hosted by intracauldron sedimentary rocks and breccias. Fluid inclusion data suggest that silver, lead and zinc were transported as chloride complexes and precipitated by cooling in veins from <5% (by weight) NaCl eq. fluids at 170° to 215°C. Silver spatially and perhaps temporally associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2002

By Stephen P. Harrison

The ventilation of coal mines has long been a major challenge for the mining industry. Prior to the 1969 Health and Safety Act, mine ventilation planning was almost entirely handled by individuals in mine operations and engineering who had extensive practical experience. Their background and expertise was sufficient to deal with existing ventilation problems and planning. A recent decline in the number of qualified individuals combined with more stringent state and federal regulations have necessitated a thorough engineering oriented approach to ventilation in mine planning design. To plan for an existing mine, a thorough ventilation survey must be conducted to determine the capabilities of the existing ventilation network. A ventilation survey also provides considerable useful data for long range planning. Essential information such as friction factors, entry resistance, and potential ventilation problem areas is gained from the survey data. With this information a comprehensive computer analysis can be conducted to evaluate alternative mine plans. This evaluation of mine plans is essential to minimize the number of shafts required while still maintaining the quality of mine ventilation. Using an existing mine as an example, this paper outlines a detailed procedure for organizing, con-ducting, and evaluating a ventilation survey. In addition, specific ventilation problem areas are isolated and alternative methods for their solution are considered. Furthermore, a long range mine plan is evaluated and the most feasible variation of the plan is selected.

Jan 1, 1980

The exploitation of mineral deposits for economical recovery of the contained minerals has many aspects differing from other industrial or manufacturing operations. However, generally accepted principles of good organization and management applicable to industrial plants are similarly effective for mineral processing plants. A more detailed coverage of organizational structures and management techniques than is possible in this section can be obtained from many good books devoted wholly to these subjects. A few of the more readily available examples are included in the general references at the beginning of this section. The field of mineral processing encompass a wide variety of minerals, processes, flowsheets, equipment, and end products. Mineral deposits, mines, and related beneficiation plants are found in all parts of the globe, often in remote locations with no nearby support for supplies and maintenance. Available labor is frequently unskilled, sometimes primitive, and often untrained without machine and hand tools or heavy equipment experience. Such situations call for well- planned and conducted training programs covering the full range of mining-type job skills. Climates can range from arctic to tropical and from arid to extremes of rain or snow, and the mine and plant sites can be almost anywhere. However, it is often possible and sometimes necessary for

Jan 1, 1985