Search Documents

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

By M. H. Pettibone

During the past decade, the size of grin- ding mills has steadily increased. Mills 11 m in diameter with 9 mW motors have been installed with even larger units on the drawing board. The rising costs of energy and labor have spurred interest in improving efficiency while reducing capital investment and operating labor. Autogenous and semiautogenous grinding have experienced renewed interest as efforts to reduce operating and capital costs have increased.

Jan 1, 1981

By Jacob Grasmick, Bill Newns

Despite ongoing digitization and “hardware” technological advances, geotechnical uncertainty remains the most significant risk in underground and tunnel construction. And, whilst they are commonly held up as an example of the sophistication of the industry, the practice of drafting and using geotechnical baseline reports is subject to a wide range of influences, not all of which support good risk management. Uncertainties in predicting ground behavior, the gap between the pre-construction assumptions, and the systemic response to construction remains a significant technical and communication challenge. Accordingly, this paper presents a framework to quantify geotechnical uncertainty using geostatistics and translate these into practical tools for ground risk management throughout planning, procurement and construction. Adopting even some of the principles of this framework should provide improvements to contract risk management and should assist to minimize the potential for commercial losses.

Dec 1, 2022

By Virgil W. Carmichael

In the Fort Union formation of western North Dakota, eastern Montana and northeastern Wyoming there are immense tonnages of lignite and subbituminous coal that have not yet been evaluated in terms of present economic conditions. Continued expansion of United States energy requirements has focused ever increasing attention on this tremendous resource, particularly as efficiency in mining and transporting of coal, as well as in electrical energy generation and transmission have improved and as hydrogenation and gasification of coal approach economic feasibility. This "total energy" concept for coal includes all of the energy uses that coal offers and has resulted in mergers of oil and coal companies and acquisition of coal re- serves by oil companies, as well as by coal companies and others. There is no doubt that these coals are entering an exciting new era of exploration and development that will result in greatly increased production. As a matter of fact, increased consumption for energy generation is well under way and recognition of the economic feasibility of high-Btu pipeline gas and synthetic petroleum products from coal is imminent. As coal is gradually displaced in steam electric generation by the more exotic fuels and processes, it will be increasingly used as raw material for the synthetic petro-chemical industry and the organic chemical industry.

Jan 1, 1968

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, “I guess that without the occasional complaint, your mine is probably over-ventilated” (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2009

By Peter Schmäh

Pipe-jacked tunnels are considered for a large variety of applications from water and sewage, cable ducts to challenging pipeline crossings or landfall construction. In most cases, Slurry MTBMs are used to carry out these projects. Continuous further development of technological features for pipe jacking plays a key role to overcome feasibility limits and to meet increased project requirements. As tightened safety regulations in terms of accessibility and escape routes increasingly limit the options of small segment lining tunnels in the diameter range below 4 m, 13 feet, pipe jacking has partially taken over. During the last decades, a growing number of large-diameter and long-distance pipe jacking projects have been completed. Experienced contractors successfully use the technological capacity of the MTBM equipment. The machine and cutting wheel have to be designed according to the ground conditions. Bentonite lubrication and interjacking stations are key factors to keep push forces moderate. For long pipe jacking drives, a so-called push module can be installed in the machine can, to be able to switch from pipe jacking to segment lining in case the machine gets stuck. The overall aim is to provide clients and the tunnel construction industry with safe and economical solu- tions for successful project execution. This presentation will present international milestone projects and will also discuss the latest developments in automation, related opportunities and limitations, and the future of digitization and artificial intelligence in pipe jacking.

Jun 23, 2024

By Biswajit Samanta, Rahul Kumar, Pranjal Pathak

The Open Pit Mine Production Scheduling Problem (OPMPSP) is a complex optimization problem that seeks to determine the best sequence for extracting mineralized material from the ground in order to maximize the Net Present Value (NPV). This process must take into account various capacity constraints, such as mining rates, processing limits, stockpiling capacities, blending requirements, and precedence constraints, which dictate the order in which blocks can be extracted. Traditionally, the OPMPSP has been formulated as a mixed integer programming problem, employing binary and continuous variables to represent the extraction of each block. However, this approach has limitations, particularly when it comes to addressing the stockpiling issue. In response, some researchers have proposed mathematical models, which offer a more accurate representation of the problem but come with their own set of challenges. In this study, an alternative approach to tackle the OPMPSP with stockpiling by employing constraint programming (CP) is explored. The method was carefully tested on the Newman1 dataset from the well-known Minelib library. The results show that the CP-based model obtained a production schedule having about 2.69 % higher NPV than the NPV of the solution, which is recorded in the Minelib Library.

Jun 25, 2023

By BHAMIDIPATI S. SASTRY, Pavan Kumar Kattamuri, ADITYA PANDEY

The thermal conductivity of rock surrounding the airway is one of the most important thermal properties for estimating strata heat transfer into the mine air and for designing the air-cooling strategies. Several laboratory methods are available for the determination of thermal conductivity; however, most of them are complex and cumbersome. The present study explains the working principle of Lee’s apparatus which is relatively simple, easy to fabricate and use, and provides consistent results. In the present study, thermal conductivities of sandstone cores obtained from an Indian coal mine are determined using Lee’s apparatus. An approach is discussed for determining the temperature gradient of sandstone specimens while cooling and used for calculating thermal conductivity. The thermal conductivity of different sandstone specimens attains values between 2.37 and 2.59 W m− 1 °C−1. For different sandstone cores obtained from the field, properties including specific gravity, specific heat capacity, thermal diffusivity, and porosity, along with thermal conductivity, are determined and highlighted in this study.

Jul 20, 2021

By O. M. Arafat, J. A. Finch

"The Functional Performance Equation calculated from a plant grinding survey defines two distinct ball mill circuit efficiencies and how they relate to total production rate through the target grind size. The survey data are also used to calculate a complete ball mill size distribution model, represented by the energy specific grinding rates, not just through the target grind size, but through all the size classes. Cyclone separation performance is represented by individual size recoveries to underflow. When these two unit operation performances are entered into the circuit modelling program (Streamline™), along with the circuit feed rate and size distribution, all the circuit survey size distributions and mass flows are perfectly regenerated by the program. The many issues associated with the historical Epstein (breakage-selection) models are eliminated. Once the circuit program is populated, pump and cyclone performance changes can be evaluated using a step-by-step procedure in order to maximize Classification System Efficiency. Mill water use and media sizing opportunities are also diagnosed in order to maximize Mill Grinding Efficiency at the size of interest. An example is provided. This circuit analysis and modelling system, and related training, is provided through a web-based application. INTRODUCTION Since its development (McIvor, 1988), the Functional Performance Equation for ball milling has facilitated new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this refreshing approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the Functional Performance “Mill Grinding Rate” at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining “selection rate” and “breakage size distribution” functions. The much simpler ball mill model presented here has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this extremely business-friendly ball mill model with optimization criteria from Functional Performance Analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/material provider, and circuit designer."

Jan 1, 2017

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981

By B. Pina

The conversion of maf coal to pyridine solubles and gas was investigated in a microautoclave batch reactor for two Kentucky washed coal samples (Ky. #9 and Ky. #11). Solvent hydrogen donor strength was controlled by the tetralin content of a mixed 1-methyl naphthalene-tetralin solvent. Primary liquefaction conversions greater than 90% in 10 minutes of reaction time at 427°C were achieved in liquefaction solvents with moderate hydrogen-donor strength (circa 40% tetralin). A modified irreversible first order rate expression, containing a parameter (a) to account for the intrinsic reactives of the maf coal, described the experimental kinetic data rather well. The integrated form of this rate expression is -k1e x = a (a- ß)e (eq. 1) Parameter ß in equation (I) is the pyridine solubility of the starting maf feed coal, x is the primary liquefaction fractional number of conversion, k1 is the specific reaction velocity constant and ? is reaction time. Primary liquefaction rate was found to be quite temperature sensitive and independent of coal when a liquefaction solvent containing 40% or more tetralin was employed. Primary liquefaction rate appears to depend on liquefaction solvent hydrogen donor strength for solvents containing = 40 wt.% tetralin. The intrinsic reactives in the maf feed coal or a appear to depend mainly on the inertinite group maceral content of the coal for the two coals studied in liquefaction solvents containing 3 40wt.% tetralin. In contrast, a appears to decrease in liquefaction solvents of low donor strength., i.e; solvents with less than 40wt.% tetralin.

Jan 1, 1984

Improvements in computer technology and associated software have allowed the improvement and development of more advanced ventilation modeling software packages including those that have the ability to simulate the effects of a mine fire on the ventilation system in terms of heat, smoke and gas distribution. This ability has real applications for the mining industry in terms of emergency planning, training and response. The primary focus of this paper will be the benefits to training programs that this type of software can provide to all types of training for various personnel, from the newly hired inexperienced miner, mine rescue, atmospheric monitoring personnel and emergency evacuation drills. The results of the simulations can then be used to give miner?s more detailed information on what types of conditions they may face based on the type and location of the fire and the program itself can be used to manipulate the ventilation system in a way that emergency response personnel may (i.e. tear down stoppings to reduce airflow to the fire area) and see the effects in real-time.

Jan 1, 2012

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Cat 994 class) as primary loading equipment in open pit iron ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Data were gathered on loader selection rationale; operating and maintenance experience; and production, availability, and cost information. Brief time studies were conducted to indicate machine performance and utilization. The paper summarizes the field data and includes economic comparisons of wheel loaders versus cable shovels in an iron ore application.

Jan 1, 1996

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By G. L. Simmons.

Many large. low-grade (refractory) sulfide gold resources exist in Nevada and other parts of the world that are not amenable to concentration by conventional flotation practice, Over the past several years Santa Fe Pacific Gold (SFPG) has investigated flotation process options to economically treat low-grade refractory resources of this type at Lone Tree and Twin Creeks. Conventional flotation technology applied to the original high-grade gold resources at Lone Tree and Twin Creeks was initially unsuccessful. Review and analysis of auriferous (gold-bearing) iron sulfide mineralogical characteristics and flotation chemistry provided a fundamental understanding that led to the development of a new flotation process that SFPG refers to as N2TEC. This paper discusses the development of this technology and compares N2 TEC results with conventional flotation practice.

Jan 1, 1997