Search Documents

By Cheng Li, Yanlei Wang, Lingrui Kong, Jianxin Tang, Fang Yuan

Coal mined-out areas have a significant impact on mining safety and affect the pressure distributions of neighboring coal faces. The PFC3D software is used to study the goaf mechanical characteristics, and the core loading test verifies the rationality of the numerical simulation method. The results from the numerical modeling showed that the void ratio, particle size ratio, and particle size distribution of the rock particle sample (RPS) had a significantly remarkable influence on the compression deformation characteristics of the rock block. The parallel-bond tensile strength and parallel-bond cohesion had a notable impact on the compression deformation traits of the rock block only when the axial stress level was lower than 12 MPa. By contrast, when the axial stress exceeded 5 MPa, the effective modulus significantly influenced the compression deformation features. However, the stiffness ratio, loading rate, and parallel-bond friction angle had almost no effect on the compression deformation characteristics. Furthermore, when the stress level was less than 10 MPa, the stress–strain curves from the rock core samples’ numerical simulation and loading tests were approximately linear. In addition, the Pearson correlation coefficients of the stress–strain curves suggest that the goaf zone’s core numerical simulation results had a robust correlation with the loading test results. The findings of this study can serve as a reference for the field application of PFC3D software and safety assessments in goaves.

Jan 18, 2022

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By Paul C. Schmall

In recent years, several geotechnical methods have been successfully applied to ash pond closure. These include modified dewatering techniques with wellpoints and wells to physically drain the material, soil mixing to create a soil-concrete material for improved accessways as well as improved ground structures within ponds to act as barriers or gravity dams, and geotechnical instrumentation to serve as an early warning of the potential for liquefaction. Given the parallels between fly ash and sluiced in place mine tailings, the application of fly ash remediation method to mine tailings shows significant potential, as illustrated in this paper.

Feb 1, 2024

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

By Peter Amelunxen, Craig Lockhart

Significant effort was made in 2003 and 2004 to upgrade the existing instrumentation and process control infrastructure at the Phelps Dodge Bagdad copper concentrator. Specifically, • cameras were installed on the feed belt for online image analysis data, • ultrasonic level sensors were installed for froth height and sump level control, • a trial froth image system was installed on one of the rougher rows, and • a new expert system to tie everything together was integrated and tuned in-house. Control philosophy, observations, opinions, and general tips and tricks are discussed with the hope of assisting other plant personnel and expert system integrators.

Jan 1, 2005

By D. Bessinger, J. Nell

The electrical conductivity of rutile was optimised as a function of time, temperature and gas composition. These optimised conditions were used to treat rutile/zircon feed prep concentrate samples from a South African heavy minerals producer, prior to electrostatic separation. Enhanced separation between rutile and zircon was obtained when compared to untreated samples. Samples treated in a hydrogen atmosphere and cooled in nitrogen showed the best separation when passed through a high tension electrostatic separator using conditions of high sample temperature and high relative humidity.

Jan 1, 2005

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997

By J. E. Urosek

Decisions made during a response to a mine fire or an explosion greatly affect the final outcome. The safety of miners should be the primary concern with accounting for all of the miners the first issue for resolution. If miners have not safely evacuated from the mine, the last known location of the miners at the time of the event and anticipated travel routes are primary exploration areas. After the mine is evacuated, there are many very important decisions that must be made quickly and often under great stress. It is critical that the mine operator establish an orderly method to direct the mine emergency response. Designation of a Command Center, staffed with personnel charged with developing plans, is a common method of establishing control. Scheduling of key mine managers will be critical, since decisions must be made 24 hours a day and people working for extended periods with little or no sleep do not always make clear or cognizant decisions. Internal communications, passing information on to subsequent shifts, and external communications with families and media must be accurate and timely. Assembling resources for responding to the mine emergency is critical for an effective response, and pre-planning can pave the way to a successful recovery. Sampling mine gasses and accurately determining the composition of gas mixtures is a common tool used to develop response plans in all fires and explosions. It is essential that preparations for emergency situations are made well in advance of a disaster. Effective communications are essential for mine management to successfully respond to a mine emergency. This paper discusses some considerations which need to be addressed in directing a response to a mine fire or explosion.

Jan 1, 2009

By M. Leslar

Slope monitoring has been an important issue in static terrestrial lidar for some time. Several solutions for monitoring the progress of a slide have been devised over the years. All of these solutions have required users to be in the field operating the lidar equipment. This paper presents a new system developed using the Optech ILRIS-HD or ILRIS-LR lidar and the scripting language of PolyWorks to produce an autonomous slope monitoring system. This system has proven invaluable in detecting and alerting mine workers to potential danger within their mine sites. It has already been deployed in two mine sites and is scheduled to be installed at a third.

Feb 27, 2013

By R. Zunich, E. Rybinski, M. Grondin, B. Flintoff

It is uncommon these days to read a business magazine or newspaper without finding a reference to Knowledge Management (KM), and its critical importance to corporate success. One definition of KM is: “getting the right knowledge to the right people at the right time and helping them to put information into action in such ways that strive to improve organizational performance.” In the minerals processing industry we could assert that we have been practicing this for years through effective operator training. In most cases we would probably be wrong. Training has certainly filled the need of addressing safety and basic operational issues, but we must collectively focus on education (learning), and the difference, as measured in outcomes, is not at all subtle. This paper briefly examines the history of training and education in the mining industry, and looks in more detail at the impact of one company’s approach to empower its workforce, while keeping the ultimate goal clearly in mind: “The great end of knowledge is not knowledge, but action.” (T.H. Huxley)

Jan 1, 2001

By A. D. Davis, C. J. Webb, C. S. Johnson

The Belle Eldridge Mine is an inactive lead-zinc mine in Spruce Gulch south of Deadwood, South Dakota. Acidic mine drainage (AMD) produced at the site drains into Spruce Creek, a tributary of Whitewood Creek. The site is on U.S. Bureau of Land Management (BLM) property. Extensive fieldwork was done at the Belle Eldridge Mine through the cooperation of the BLM and the South Dakota School of Mines and Technology. The site was extensively mapped to identify physical and environmental hazards such as tailings, waste rock, collapsed buildings, adits and workings. An exhaustive search of the historical records of the Belle Eldridge Mine was conducted. Maps of the under-ground workings of the Belle Eldridge dating from the 1930’s and 1940’s were found. The maps were used to correlate currently collapsed features to old adits and tunnels. Using hand corers and a portable drill rig, waste rock, tailings and soil core samples were collected and depth to bedrock was determined and the total volume of waste and tailings pile were determined. Related work examined the hydrology of the site. The site is very complex hydrogeologically. Numerous underground and surface workings and tunnels add to the complexity. Several seeps are located at the site, one of which is producing AMD. Recharge to the site was studied, and a 100-year flood plain map was produced.

Jan 1, 2000

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Frank W. Luerssen

Introduction "Austerity" is perhaps an overly generous description of the past three years in the American steel industry. Steel plants operated at an average of only 57% of their capability in 1982-84. The dismal losses for last year are still being totaled. But during the two years before this period, American steelmakers recorded an aggregate net loss of a staggering $6.8 billion. Steelmakers responded by closing numerous marginal facilities. And production capability was cut by 13.6 Mt (15 million st). Capital expenditures still averaged $2 billion annually. But this was inadequate to maintain the existing base of steelmaking facilities. The general economy experienced a satisfactory recovery during this period. American steel, however, continued to suffer from a lagging recovery in the capital goods sector. This was due to record penetration of its domestic market by imports and from very weak realizing prices on the volume that was available. In addition to the direct influx of offshore steel products - which itself depressed prices - the industry also became painfully aware of the growing importance of "indirect" imports. These came in the form of steel-containing producer and consumer durables. Industrial equipment and autos fabricated from foreign steel accounted for the equivalent of 6 Mt (6.5 million st) of lost market opportunity for domestic steel-makers last year. That is over and above the 23.5 Mt (26 million st) of direct steel imports. Given these factors, Inland Steel was not spared from the threeyear downpour of red ink. Despite its record of continuing modernization in steel, our single-plant location in the world's best steel-consuming market, and the high proportion of consumer durables related products, such as cold rolled and coated sheet in our mix, Inland suffered aggregate losses of $277 million during the 1982-84 period. Strategic Planning The foregoing establishes a perspective - a base from which we have restructured our view of the steel industry, and of our own role within that picture. Until possibly two years ago, this present weakness in steel demand was viewed around the world as an aberration, eventually to pass. By contrast, it is now recognized that austere times are the normal steel environment. The topic here is management of resources. This implies an emphasis on strategic planning. It is worthwhile to examine some of the more critical assumptions that were driving strategies among a number of steel companies just before the 1980s. Those projected characteristics of the future steel environment were arrived at through painstaking analysis. They were carefully and heavily quantified and were generally shared by outside observers and our peers within the steel industry. • First, the assumption was made that domestic steel demand would continue to grow at an average rate of 2% per year. • Second, it was assumed that this growth in the American market would continue to be filled predominantly by US mills. It was believed that increases in steel and steel-related demand overseas would absorb much of the ominously growing capacity of third

Jan 6, 1985

By M. K. McCarter

The history of mining education, like the history of the mining industry, is typified by “boom and bust” cycles. In academia, the perpetual problem can be stated as “too many graduates for the jobs or too many jobs for the graduates.” The deep “bust cycle” that spanned the 1990s through 2003 spawned renewed efforts to eliminate, consolidate, restructure, rename, reinvent or otherwise change mining education to make it (for some) more fiscally or socially acceptable. During this period, a number of mining programs were eliminated, and by the late 1990s senior people in academia and their counter-parts in industry became increasing concerned about the very real possibility that strategic disciplines may disappear altogether. As a result, the Mining and Metallurgy Society of America (MMSA) created an educational committee to explore how industry could help preserve key programs necessary to provide future professionals. Several meetings were held to assess the problems and look for solutions. In 2004, this effort culminated in the first of the “Engineering Education” sessions to be held at the SME Annual Meetings. In response to the information presented in this first meeting, Marc LeVier (then president of MMSA) invited a number of the participants to reconvene the following day. An action plan was formulated and a task force was organized. To more fully represent all industry sectors, SME later that year assumed the sponsorship role for the task force.

Jan 1, 2007

By D. M. Avant, S. M. Pickering

A variety of grades of very white muscovite mica are now being produced from sedimentary sands and clays in Central Georgia. The mica is naturally concentrated near the base of the lens-shaped kaolin deposits and also disseminated in associated quartz sands. The same weathering and bacterial alteration processes which have transformed the kaolins from dark organic muds to white pigment-grade industrial clays have also removed discoloring iron from the micas and developed unusually white muscovite. Further, chemical alteration has removed some potassium from the muscovite atomic structure, resulting in an easily delaminated mica which can be cleaved to unusually fine, high bulking, high aspect ratio products. The peculiar alteration history of these sedimentary micas enables production of some of the whitest, finest particle size, and thinnest aspect ratio muscovite mica products on the world market today. Raw mica feed is obtained from kaolin and sand processing by-products, and also from beneath the useful base of abandoned kaolin mines. The processed ultrafine and filler grade muscovite mica products are used for paint, plastics, cosmetics, mold release, thermal and electrical insulation, epoxy, and dry wall joint cement markets.

Jan 1, 2002

By BHAMIDIPATI S. SASTRY, ANMAYA NAIK, ASIF AHMAD, Srivatsan Jayaraman Sridharan, ADITYA PANDEY

Wet kata cooling power (WKCP) as measured by a kata thermometer is a well-known heat stress index used in the mining industry. Although, over the years, several researchers proposed different heat indices and indicated limitations of the kata thermometer, WKCP is used in the South African gold mining industry due to its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for the WKCP and some of the more commonly used empirical models. For this purpose, WKCP measurements are obtained based on experiments conducted in a low-speed wind tunnel. Based on a regression technique, the analysis presented aims to assess the disagreement between the empirical model predictions and actual measurements. The correlation is also presented between WKCP and the well-established thermoregulation models using parameters from the low-speed wind tunnel experiments, including dry-bulb temperature (Td), wet-bulb temperature (Tw), barometric pressure (P), and wind speed (v). It is found that the proposed empirical model for the WKCP represents the bioclimatic interaction quite well under the specific parameters that defines the harsh thermal environment and air condition, such as metabolic activity, clothing of the person, and the velocity of the ventilating air in which the person is working. The statistical analyses performed show that the empirical model proposed for the WKCP produces satisfactory estimates of the thermal stress experienced under lower air velocities, light clothing, and higher metabolic activity rates.

Sep 2, 2021

By David J. Lowell

The gold content of porphyry copper deposits ranges from less than 0.05 g/t to more than I g/t ((0.0017 to 0.035 oz per st) and the average is about 0.05 g/t (0.0017 oz per st) gold. Perhaps the highest grade mineralization found near a porphyry cop¬per deposit is the Ok Tedi Gold Cap ore body whose grade falls in the 2 to 3 g/t (0.07 to 0.1 oz per st) range. It is difficult to define a gold-rich por¬phyry copper deposit. All porphyry copper ore bodies contain some gold, but there seems to be a fairly sharp break in the gold content at about 0.1 g/t (0.003 oz per st) gold. There is also a problem in identifying dis¬seminated gold deposits that may have an indirect relationship to porphyry copper systems. This relationship is clear cut in deposits such as the Ok Tedi Gold Cap, the El Hueso deposit, the Fortitude and West de¬posits at Battle Mountain, NV, and the Sur¬prise deposit at Ely, NV. There are many other bulk disseminated, epithermal-type gold deposits - McCoy, NV, for example - that might be related to a porphyry system but where this relationship is remains very uncertain. In such places as the Goldfields and Tonapah district in Ne¬vada and in the El Indio, Chile district, there may be a vertically stacked ore deposit rela¬tionship between near surface epithermal deposits and disseminated molybdenite and chalcopyrite enargite mineralization at depth that may represent a deep porphyry system. This, however, has not been positively demonstrated. Most of the bulk epithermal gold deposits are probably not related to porphyry copper systems. Exceptions would probably be Ok Tedi, El Indio, El Hueso, Battle Mountain, and Lepanto where vertical or lateral zoning relationships are more apparent. This author believes that porphyry copper systems are related to a relatively unique type of intrusion that is probably distinct from, for example, the McCoy intrusivebody. For that reason, deposits such as McCoy, Chimney Creek, and the like will not be included in the definition of gold-rich por¬phyry copper deposits for this article. The interpretation of the origin of several of the deposits previously mentioned are subject to an unusual amount of contro¬versy. For example, geologists seem to be equally divided about the presence of a porphyry copper deposit below the El Indio deposit. Geologic setting Continental vs. island arc Several geologists have speculated that the gold-rich, moly-poor, porphyries are

Jan 1, 1989

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009