Search Documents

By T. R. Kostecki, A. J. S. Spearing, A. Hyett, M. Gadde

Ground control research for underground coal mining has progressed significantly over the past several decades. With this progression, and the ability to analyze and model underground conditions, underground working conditions have significantly improved. In order to progress further, the behavior of roof support must be known and be adequately modeled, such that models can be used for support design under different geological and mining conditions. This paper discusses the results from a research project funded by the U.S. National Institute for Occupational Safety and Health (NIOSH) and undertaken by Southern Illinois University Carbondale and Peabody Energy. The research involved installation of active and passive instrumented bolts in mines, recording relevant in situ data and then attempting to model the behavior of the bolts as mining progressed. Such calibrated models could aid in design of roof supports under different geological and mining layouts and thus, hopefully, further improve rock related safety.

Jan 1, 2012

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By T. P. Meloy

Traditionally the mineral and mining engineers have characterized particles by sieving and-settling. Within the last decade, with the advent of the scanning microscope, entirely new experimental and theoretical approachesl-10/have been taken to minutely define the particle surface. This approach depends upon a hypothesis which takes advantage of the recent developments in automatic micro-scopes which can acquire large amounts of information in a short time and the new computational techniques which rapidly reduce the information to meaningful, practical data. Historically sieving and settling are the oldest sizing techniques known. Sieving by square screens, shown on Figure l-A is a common, current practice for sizing particles both in the laboratory and in production. A woven cloth is used which usually has square openings. The size particle that will pass through the opening dependent on a complex relationship of its morphology. As can be seen in Figure l-A, neither the width nor the height of the particle is determined by sieving. From square screens one and only one parameter characterizing the particle size is obtained, that parameter is the radius of the sphere that will just pass through the given sieve opening. A variation of square mesh screen is the slot screens, shown in Figure 1-B. Here another measure more closely associated with the height of the particle is obtained. Once again, one and only one parameter is associated with the particles' shape.

Jan 1, 1977

By Malcolm Ross

Asbestos crystallizes within rock formations undergoing intense deformation characterized by folding, faulting, shearing, and dilation. Some of these conditions have prevailed during formation of the taconite iron ore deposits in the eastern Mesabi Iron Range of Minnesota. This range includes the Peter Mitchell Taconite Mine at Babbitt, Minnesota. The mine pit is over 8 miles long, up to 1 mile wide. Fifty three samples were collected from 30 sites within areas of the pit where faulting, shearing and folding occur and where fibrous minerals might occur. Eight samples from seven collecting sites contain significant amounts of ferroactinolite amphibole that is partially to completely altered to fibrous ferroactinolite. Two samples from two other sites contain ferroactinolite degraded to ropy masses of fibers consisting mostly of ferrian sepiolite as defined by X-ray diffraction and TEM and SEM X-ray spectral analysis. Samples from five other sites contain unaltered amphiboles, however some of these samples also contain a very small number of fiber bundles composed of mixtures of grunerite, ferroactinolite, and ferrian sepiolite. It is proposed that the alteration of the amphiboles was caused by reaction with water-rich acidic fluids that moved through the mine faults and shear zones. The fibrous amphiboles and ferrian sepiolite collected at the Peter Mitchell Mine composes a tiny fraction of one percent of the total rock mass of this taconite deposit; an even a smaller amount of these mineral fragments enter the ambient air during mining and milling. These fibrous minerals thus do not present a significant health hazard to the miners nor to those non-occupationally exposed. No asbestos of any type was found in the mine pit. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Amphibole; Reserve mining; Tailings; Mesabi iron range; Mineral fibers

Jan 1, 2007

By Betty L. Gibbs

Geologically simple deposits can be modeled quickly and easily with inexpensive gridding and mapping software. Hundreds of mines around the world use RockWorks99 and Surfer 7 for generating contour maps, producing log plots and cross sections, and performing other useful geological calculations. These programs are used by many mining operations as their only modeling and graphical software or they are used in conjunction with larger systems. The investment in learning time is low and the programs produce reasonable quality results with standard computing equipment. RockWorks99 and Surfer 7 provide a good level of capability while maintaining high quality technical integrity. Both programs are used for many applications in mining, oil and gas, environmental and other fields that require analysis of spatial data.

Jan 1, 2000

By James P. Connell

The American Concrete Institute defines "shotcrete" as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity unto a surface." This definition thus includes what is traditionally known as "gunite," which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this paper. In 1914, following the invention of the mortar gun in 1907, the then Chief Engineer of the U.S. Bureau of Mines, George Rice, developed the guntie process for underground test work at the bureau facility at Bruceton, Pennsylvania. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto Tunnel in California. The greatest development was In Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Intially, shotcrete was used to reduce manpower requirements for forming; and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately niter the opening had been made. The incorporation of wire mesh into the shotcrete led to the New Austrian Tunnel Method, or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the U.S. reliance on wood or steel supports in main line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to the new and seemingly unrealistic lighter shotcrete support.

Jan 1, 1977

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By S. L. Ducummon

Inactive underground mines now provide essential habitat for more than half of North America's 44 bat species, including some of the largest remaining populations. Thousands of abandoned mines have already been closed or are slated for safety closures, and many are destroyed during renewed mining in historic districts. The available evidence suggests that millions of bats have already been lost due to these closures. Bats are primary predators of night-flying insects that cost American farmers and foresters billions of dollars annually, therefore, threats to bat survival are cause for serious concern. Fortunately, mine closure methods exist that protect both bats and humans. Bat Conservation International (BCI) and the USDI-Bureau of Land Management founded the North American Bats and Mines Project to provide national leadership and coordination to minimize the loss of mine-roosting bats. This partnership has involved federal and state mine-land and wildlife managers and the mining industry. BCI has trained hundreds of mine-land and wildlife managers nationwide in mine assessment techniques for bats and bat-compatible closure methods, published technical information on bats and mine-land management, presented papers on bats and mines at national mining and wildlife conferences, and collaborated with numerous federal, state, and private partners to protect some of the most important mine-roosting bat populations. Our new mining industry initiative, Mining for Habitat, is designed to develop bat habitat conservation and enhancement plans for active mining operations. It includes the creation of cost-effective artificial underground bat roosts using surplus mining materials such as old mine-truck tires and culverts buried beneath waste rock.

Jan 1, 1997

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

It is widely accepted that particles stabilise flotation froths and that stable froths result in improved flotation performance. Predicting the effect of particle addition on froth stability is, however, challenging. Dynamic surface tension measurement using maximum bubble pressure presents an attractive technique to investigate the effect of surfactant and particles at the air-water interface. The range of bubble lifetimes that can be studied (typically 0.1 to 60 s) is analogous to variations in air rate in flotation cells, and the corresponding changes in surface tension give an indication to the diffusion and adsorption rates of particles at the interface. In this paper, we use dynamic surface tension measurements to investigate the effect of particles on bubble surfaces at the microscale and link this to bulk froth stability measurements carried out using a froth column. Using the maximum bubble pressure method, the results show that the addition of particles results in lower surface tension, both at the dynamic (i.e. short) bubble lifetimes and towards equilibrium (i.e. 60 s bubble lifetime). This corresponds with the bulk froth stability measurements, where the three-phase system yielded more stable froths than the surfactant only system. Furthermore, increased particle loading at the air-water interface, whether through higher surfactant concentrations or lower air rates (longer bubble lifetimes), gave lower surface tension and higher froth stability. This demonstrates the link between bubble loading and froth stability. It is proposed that the maximum bubble pressure technique can be used to predict froth stability for two- and three-phase systems, enabling the effect of particle loading to be accounted for and quantified. Moreover, the technique has the potential to allow rapid determination of particle and surfactant diffusion at the air-water interface and prediction of the corresponding effect on bulk froth behaviour.

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By J. N. Murphy

The use of the National Science Teachers Association (NSTA) regional meetings as a forum to educate teachers on the role of minerals in our society has been immeasurably successful. Each year, on average about 3,500 to 4,000 teachers participate in each of the three regional NSTA meetings. At each of these meetings, nearly 2,000 teachers visit the “Minerals Coalition Booth” and receive free mineral samples and other educational support materials. Some rules of thumb for a successful booth at the NSTA are provided. Considering the level of effort for such a booth, are there alternatives? The NSTA also organizes a national annual meeting with attendance of about 20,000. All who have participated in a regional NSTA agree that the traditional approach of providing a mineral set and teacher materials for a substantial fraction of the 20,000 attendees is not feasible. Conceptual alternatives for minerals education at the national NSTA meeting are introduced and evaluated.

Jan 1, 2001

By M. S. Klima, P. T. Luckie

Proper analysis of washabiity data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Feb 24, 1997

By E. F. Schnitzer, S. R. Mamoyac, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By J. Parker

Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa (4000 and 7000 psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition

Jan 1, 1991

By Beverly Cramp

In 1995, mining engineer Alain Gachet thought about using Earth-observation satellite imagery to search for precious minerals. The latest radar Earth-observation satellite, Canada’s RADARSAT-1, had just been successfully launched at the time, creating new opportunities for commercial applications. Gachet was working in Congo Brazzaville as an oil executive and general secretary of Elf Congo for the French national oil company Elf Aquitaine. He understood that the RADARSAT-1 launch promised new and cost-effective sources of data for mineral and oil exploration. “It was early 1996 before I ordered my firstRADARSAT-1 satellite images,” said Gachet. “I was first struck by the quantity of information delivered by the radar images. Linear structures and faults were clearly defined and subtle topographic features were tremendously enhanced,” he said. “It was ‘tree top geology,’ but this kind of information appeared to be key for finding new gold seams.”

Jan 1, 2003

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020