Search Documents

By Weijian Yu, Genshui Wu, Jian Zhang, Yong Ning

Aiming at characteristics of the soft coal roadway engineering geology and deformation, the exposure research of the soft coal seam, theoretical analysis, numerical calculation and program design were carried out. First of all, according to the disclosure, soft coal seam engineering characteristics and geological conditions in Xinxing coal mine were expounded. Meanwhile, the soft coal roadway bolt supporting axial effect, the bolt supporting transverse effect, the anchorage body mechanics strengthening mechanism and problems such as supporting strength have been analyzed. The paper pointed out that the soft coal with very small cohesive force can form a composite anchorage body under the combined action of the anchor cable group, the W-type steel band and the metal net. The soft coal body in the plastic damage area formed anchorage balance arch with a certain bearing capacity and adapted to the rock deformation, and which played an effective support role in the roof outside the balance arch of the roadway. Therefore, the full-cable support technology was proposed. And then, numerical calculation and comparative analysis were conducted on three schemes of the roadway with non-support, with combined support of “anchor bolt and cable” and the full-cable support. The results show that when the roof is supported by anchor cable, it not only controls the continued increase of the subsidence value of the roof, but also effectively suppresses the convergence amount of the floor heave value and the amount on the sidewalls of the roadway. Whether it is from the stress distribution situation, or the viewpoint of plastic zone scope, the combined support of full-cable is more reasonable than that with non-support and that with the combined support of “anchor bolt and cable”. Finally, based on the features of soft coal seam in No.2265 work face of Xinxing coal mine, the relevant support schemes were put forward, and its specific support parameters and cross-section designs were drawn as well.

Jan 1, 2017

By Vas P. Srinivasa

A comminution circuit is an important integral part of a mineral processing plant. Nearly 40% of the capital cost and 30 to 40% of the operating cost are taken up by the crushing and grinding circuit. Therefore, considerable care should be given to the design and selection of this circuit. Several factors affect the selection of a comminution circuit--energy consumption, avail- ability of the equipment, the remoteness of location, and availability of trained personnel, to mention a few. Each of these factors influences the choice. Selecting a comminution circuit strictly on lower capital cost may not be optimal. Crushing and grinding circuits are usually site specific and should be selected - only after careful analysis of all the factors involved. The objective of this paper is to show the effect of these factors, which are extranious to capital cost. Usually, the capital cost of a semiautogenous grinding circuit is lower than that of an equivalent conventional circuit. However, due to lower equipment availability and high power costs in certain locations, the economic advantage of lower capital cost is lost. Analysis indicates that a break even point occurs at a power cost of 5¢/kWh. This paper describes the procedure utilized for selecting the most economic comminution circuit and states the conditions applicable for each cominution circuit.

Jan 1, 1983

By J. C. Norman

The United States was the world’s largest producer and consumer of boron compounds during 1995. According to estimates from the US Geological Survey(USGS), boron mineral concentrate and chemical production in the United States totaled an estimated 1.1 Mt(1.2 million st) yielding 602 kt (663,000 st) of B2O3 for an estimated value of $462 million. This level of production exceeded 1994 revised production figures by about 9%. The United States continued to provide nearly all its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. During 1995, about 900 people worked in domestic boron mines and plants, about the same as in1994. USGS estimated total world production of boron during 1995 to be about 3 Mt (3.3 million st), yielding about 1.6 Mt (1.8 million st) of B2O3. World production in 1995 was about equal to revised 1994 levels.

Jan 1, 1996

By John W. Wilson

Every operation connected with the working of a deep-level mine has, to a greater or lesser extent, a direct bearing on the costs of production, and hence, profitability of the mine. If adequate mine planning is not done in the early stages in the life of a mine, considerable expenditure can result from the cost of maintaining mine service tunnels, production delays in stopes caused by poor strata control, distortion of fittings in hoisting shafts, rockbursts and so on. In fact, the optimum profitability of a deep-level, hard-rock mine can only be achieved if the layout of the shaft systems, ore passes, tunnels, stoping areas and other underground excavations are designed to withstand or accommodate the rock stress conditions that will be created by mining operations. In South Africa where the deepest mines in the world are located, access to the underground workings of most deep-level gold mines is via vertical shaft systems and a network of tunnels connecting the shaft systems to the stoping areas. In current practice, there are two basic methods of extracting the gold-bearing reef,* namely, the scattered stoping method and the longwall stoping method. The choice of the stoping method is governed largely by the anticipated gold distribution and payability of the reef in the area, the geological conditions, the degree and complexity of faulting and dyke intrusions, the depth at which the gold-bearing reef is to be mined and the inclination and width of the reef. The longwall system was first introduced at the East 717 Rand Proprietary Mines Limited in 1942 in an effort to combat the rockburst hazard which appeared to increase with increase in depth. This mining method became standard practice on that mine for stoping operations 700 ft. below the surface. Since that date, several deep mines on the Central Rand, East Rand and West Wits gold mining areas have adopted this method.

Jan 1, 1977

By M. Karmis

The determination of the surface area which may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted Furthermore, the influence of both mining and geological factors, such as mining width and depth and overburden lithology, on this angle is examined, using the Surface Deformation Prediction System (S.D.P.S) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1994

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By Stefan Lorenz, Robert Galler

"The technical lifetime of underground structures does not only depend on the long-term behavior of individual support elements and material characteristics, but also on various boundary conditions, which influence the entire long-term system behavior of the structure. Thanks to the construction of second tunnel tubes and the corresponding cross passages sampling of support materials such as shotcrete, concrete of the inner lining and rock bolts including sheet membranes is possible. To evaluate the stresses and the supporting effects of the tunnel shells, flat-jack tests and different simulations were performed. With these simulations the percentage of the load bearing behavior of the shotcrete shell can be determined. From the results, conclusions for new design approaches for tunnel construction should be generated. New concepts, in which the outer lining is part of the permanent support elements can be considered. This approach would be applicable for conventional as well as mechanical tunneling. INTRODUCTION Tunnels are an indispensable part of modern transport infrastructure. As multi-generation structures their long-term preservation as well as their technical service life is of central importance. The current state of research in the field of durability of structural elements must be considered separately. In almost all areas a prediction of materials and structural components towards lifetime exists. System-wide investigations were rarely performed, so that there is no technical lifetime consideration of the outer lining in systems included. In this study the mechanical behavior of the interface connection in a double shell lining (DSL) tunnel was investigated in laboratory tests. Objective The target of this work is, at first, to create a large database with the lifetime of different structural elements and materials, which may be the basis of durability considerations of tunnels. Secondly, the goal of these investigations is to optimize tunnel designs and their dimensioning regarding to the technical lifetime. For that matter, it is necessary to analyze the selected approaches of the loss of strength and stiffness of the outer lining."

Jan 1, 2016

By Holger Witthaus

Various seam conditions had been examined during longwall production at RAG German hard coal mines. Based on the field data a prediction method was developed considering separation planes as influencing factors for roof falls at the face. The characteristics, orientation, and density of separation are important factors on the occurrence of roof falls. In addition to geological influences, the performance parameters and geometry of support must be considered and optimized for the prediction and prevention of roof falls in a longwall face. Based on detailed macro- and microscopic investigations of e coal seams considering various ranks of carbonization, the origin and characteristics of separation planes are determined and a strata-specific influence on roof fall is interpreted. It was assessed that the coal face fracturing and displacement caused by the stress depend on the floor and roof strata conditions due to activation of the existing separation planes. Field studies are shown giving an idea of influences by advance rates of the longwall face, support delay and hydraulic pressure to the roof control in longwall faces in depth of more than 3000 ft. The analysis includes the application of specific software developed for longwall roof fall prediction as a result of a European research project. The software allows a laminar graphic display of roof fall probability, which is used for recognition of risk areas and risk management.

Jan 1, 2009

By Miguel Angel Banuet Rodriquez, Hector Conceso Aragon

"Construction of the longest road tunnel in Mexico is part of Acapulco’s alternate roadway to the scenic roadway project. This article provides a brief summary regarding details of the construction since the project began. Work was done by skilled engineers and Mexican workers that includes outstanding execution of the work in an urban and tourist area. This project will have a strong impact on the steady development of the port of Acapulco.Project locationAcapulco’s Alternate Roadway Project is currently under construction in the city of Acapulco, located in the Guerrero state of Mexico. It is an 8-km (5-mile) long roadway that starts at the Icacos neighborhood, heading toward Acapulco’s airport, crossing a drill-and-blast tunnel that is 3,160 m (10,350 ft) long under Veladero Park, a mountainous area. The tunnel overburden reaches a depth of 380 m (1,250 ft) approximately at the central point of the horizontal alignment, and continues with a 4-km (2.5-mile) long elevated road to connect to the existing Viaducto Diamante toll road (Fig. 1).Tunnel construction has already been finished using two portals for drilling and blasting operations; Brisamar Portal on the west side and Cayaco Portal on the east side (Fig. 2).Geometric dataOnly two main excavation cross-sections were considered in the executive design. The first one corresponds to the running tunnel for a three-lane vehicle section, with crosssection areas between 120 and 130 m2 (1,290 and 1,400 sq ft) taking into consideration different geological and geotechnical conditions to be encountered (Fig. 3).The second one corresponds to eight emergency bays, each one 50 m (164 ft) long, laid down within the tunnel outline, located at 400 m (1,312 ft) from each one with excavation cross-sections between 156 to 169 m2 (1,680 to 1,820 sq ft), in accordance to geological and geotechnical conditions to be encountered (Fig. 4).The tunnel’s horizontal alignment is completely straight, having a small curve within the vertical alignment on Cayaco portal, because there were some differences in levels when tunnel excavation started. Tunnel slopes were designed in such a way that rainwater does not run down into the tunnel at any time."

Jan 3, 2018

By Alexander E. McHugh

A study of some variables affecting the recovery of molybdenum from oxidized molybdenum minerals was made. The effects of variations in contact time, temperature, pulp density, particle size, and solvent concentration on the recovery of molybdenum using acid and alkaline solvents were investigated. Chemical analyses, screen analyses and microscopic examinations were made and the presence of important elements determined. A hydrometallurgical method was developed to recover the molybdenum from the oxidized molybdenum ore by simultaneous dissolution of the molybdenum with sulfuric acid, adsorption on activated charcoal and flotation of the charcoal. The molybdenum was extracted from the activated charcoal with sodium hydroxide, precipitated with calcium hydroxide as calcium molybdate and this regenerated sodium hydroxide for additional stripping. A solvent extraction method, using mines, was also studied to recover molybdenum from both alkaline and acid molybdenum solutions. Satisfactory results were obtained.

Jan 1, 1967

By N. A. Abdel-Khalek

An experimental study was carried out to compare the results of laboratory column flotation versus conventional flotation for the cleaning of fine coals of different rank and their oxidized samples as well as discrete size fractions. Surface oxidation caused a significant reduction in the flotation yields achieved with both methods. However, the column flotation produced concentrates? of lower ash content. The recovery -size curve achieved with column was similar in shape to that obtained with conventional cell, with superior results in the region of fine fractions. The influence of some column operating parameters was also discussed.

Jan 1, 1990

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By J. L. Bellanca, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not constitute endorsement by NIOSH. ABSTRACT Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which presents an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders' evaluations. The study includes considerations for safe technology integration. INTRODUCTION Striking, pinning, and crushing accidents related to mobile machines continue to be a major concern in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) linked 22 of the 75 underground mine fatalities reported between 2011 and 2015 to power haulage [1]. The Mine Safety and Health Administration (MSHA) asserts that proximity detection systems for mobile machines (mobile PDSs) could help to prevent these types of fatal injuries [2]. Mobile PDSs use a collision avoidance technology that allows the mine to establish hazard zones and employ electromagnetic sensors to detect workers equipped with a miner-wearable component (MWC) working near these mining machines. The authors characterize a mobile PDS as an automated technology, because—in line with Lee & See’s [3] definition of automation—a mobile PDS actively “selects data, transforms information, makes decisions, or controls processes” (p. 50). When the system detects workers in the established hazard zones, it issues alerts and slows or stops the mobile machine. Even though a mobile PDS may be a viable and promising safety solution, there are still a number of questions regarding how well this automated technology will fit with mining tasks and conditions. Using a mixed-methods approach, the current study explored factors that influence the fit of mobile PDSs in the underground mining environment.

Jan 1, 2019

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By Andre C. Zingano

It is a very difficult task to estimate the immediate roof and support behavior in a room-and-pillar mining section in the initial phase of the mining project. There is little information available at this phase, and it is restricted to geomechanic characterization of the rock layers from cores samples, and the in-situ instrumentation of experimental entries and intersections. Even being a pilot excavation for roof support test a good indicator for the behavior of the immediate roof, its behavior for a full excavation mining section is different from a single intersection of two entries, mainly because the stress redistribution caused by the multiple entries excavation and face advance for a full excavation section. The objective of this paper was to calibrate a 3-D numerical model of an experimental intersection, based on the in-situ instrumentation of an experimental intersection excavation, and the geomechanic description of the rock layers. The numerical model was built with the same specifications as the excavation test, including the entry geometry and roof support. The numerical model calibration was based on wire extensometers that were installed at different positions in the roof of the pilot excavation, and on the geomechanic characterization of the rock layers that form the roof, coal seam, and floor. Therefore, it is possible to estimate whether the roof support specification adopted in the test phase will be good enough for the development of the entire mining section.

Jan 1, 2009

By Roy A. Grancher

HAPPY BIRTHDAY Not only is 1971 the Centennial Year of the AIME, but it also marks the One Hundredth Anniversary of the United States Portland Cement Industry. On September 26th in 1871 David O. Saylor of Allentown, Pennsylvania, received his patent Numbered 119,413 for the manufacture of portland cement. "Cement" had been used in the United States before that. This was, however, natural cement - a direct product of rocks as found in nature, usually burned at low temperatures in open kilns. During the early 1800s this natural cement played an important role in such projects as the building of the Erie Canal. It was only after the Civil War that small amounts of high priced portland cement was imported from Europe. The successful use of this material in construction led to Saylor's experiments and subsequent patent for the manufacture of a scientifically controlled product in this country. These one hundred years have witnessed four major "ages" of cement . . . three of them occurring in the last quarter century since World War Two. The first age was the "Age of Development", a seventy-year period which saw the growth of cement and its concrete end uses as major construction materials. Next followed a period called the "Age of Demand" when, after the war, cement became in short supply relative to large building requirements. In effect a cement shortage existed. The decade of the Sixties proved to be the "Age of Reaction", with its courses of action coming in response to the problems that arose when the industry's expansion programs provided too much capacity. Today cement, and the concrete industries, find themselves entering the "Age of Reason". Overcapacity, low price, rising costs, and poor returns are several of the reasons behind that name, As these industries face the construction challenge of the Seventies, and beyond, the application of basic management principles (otherwise known

Jan 1, 1971

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By L. W. Pommier

In the field of minerals processing the concentration of valuable minerals normally takes place in suspensions of ore particles in liquids. The fluid resistance offered by Newtonian liquids to the movement of free settling spheres for the limiting cases of creep flow and turbulent flow is well described by Stokes' and Newton's Laws. However, these equations are not applicable to non-Newtonian fluids, since the relationship between applied shearing stress and resulting rate of shear is a non-linear function, and more than one viscosity parameter is necessary to describe their rheological properties. For this reason, the term "apparent viscosity," which has been commonly used to explain the flow resistance of the non-Newtonian systems including suspensions, may be misleading. A rigorous analysis of the mechanisms of momentum transport of solid-liquid systems is complex indeed. There are many variables that affect the properties of such systems, and precise limitations and assumptions are necessary in order to produce quantitative relationships for predicting their behavior. Very dilute suspensions of spherical particles in Newtonian liquids of identical density as the solids have been examined in the past (12); however, the study of suspensions in which there is a considerable difference in density, between the liquid and the suspended solids has been neglected.

Jan 1, 1968