Search Documents

By Terry L. Logan, Arfon H. Jones, James C. Seccombe

Deeply buried coal seams [greater than 3000 ft (914 m)] are difficult and sometimes hazardous to test and complete due to coal sloughing, formation pressure anomalies and coal fine generation. Data collected while stimulating two deep coalbed methane wells located at the Gas Research Institute/Resource Enter¬prises, Inc. "Deep Coal Sean Project" test site in the Piceance Basin, Colorado, is presented in this paper. A single thick coal seam was completed openhole in each well. Core data, reservoir data, in-situ stress measurements, and pre-stimulation calibration test data were collected at the site to use in the design of the fracture stimulation treatments for both wells. A nitrogen foam fracture fluid treatment was selected for the first well and a linear gelled water for the second well. Treatment pressures were monitored with a downhole quartz pressure transducer. Atypically high treating pressures were observed, possibly indicating coal fines plugging at the fracture tip or increase in fluid viscosity caused by interaction of the generated coal fines with the fracturefl uid. In addition, a comprehensive fracture diagnostic effort was employed during the fracturing of the second well; namely, triaxial borehole seismic, seismic televiewer, hydraulic impedance monitoring, gamma ray log (in conjunction with radioactive additives in the sand), and temperature log. The results indicate a vertical fracture was created parallel to the face cleat as expected.

Jan 1, 1986

By Elwyn King, Donald J. Dodds

"...Unfortunately, the research activities in soil mechanics had one undesirable psychological effect. They diverted the attention of many investigators and teachers from the manifold limitations imposed by nature on the application of mathematics to problems in earthwork engineering. As a consequence, more and more emphasis has been placed on refinements in sampling and testing and on those very few problems that can be solved with accuracy. Yet accurate solutions can be obtained only if the soil strata are practically homogeneous and continuous...." This statement about soil mechanics was made by Karl Terzaghi, thirty years ago and applies to a greater degree today to the infant science of rock mechanics. More uncontrolled variables are added to the already many existing in soil mechanics. Variables, such as Macro-discontinuity and in situ stress levels. In no other field of engineering are the problems as site oriented. Presently this site dependance demands the investigator or rock mechanics engineer to get his hands dirty rooting in the muck of a tunnel floor trying to properly install or readout test apparatus in a comprehensive site investigation. This paper discusses such a site investigation designed to determine the problems and solutions inherent in the driving of the Trans Koolau Tunnel. The paper will describe the various types of tests to be performed, how the results are to be used and the interrelation of the various tests themselves.

Jan 1, 1997

By R. Karl Zipf, Z. T. Bieniawski

Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation. In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions. An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further under- standing of the mechanics of fine fragment formation in coal.

Jan 1, 1986

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal sup-ports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

Jan 1, 2004

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By Dennis J. Lachel, Lloyd B. Underwood

In recent years a great number of papers have been presented at symposiums and have appeared in the literature relative to geologic prediction for rapid excavation and tunneling. Many of these papers describe research projects now underway to investigate tunnel site selection by remote sensing techniques, seismic holography, electro¬magnetic pulse sounding, optical scanning for structural features, and many other exotic geophysical techniques. While it is possible that this research will produce techniques that may prove to be very useful, it appears for the present at least, and perhaps for another decade, that there still will be no substitute for conventional exploration methods such as coring boring, geologic mapping, studies of existing wells, and proven geophysical techniques. Nevertheless, there is still room for tremendous improvement in the conventional techniques for geologic prediction in tunneling. These include: more rapid and accurately aligned coring borings drilled parallel to the tunnel alignment; improved geophysical surveys both prior and during construction; improved methods for predicting ground¬water inflows and water pressures, both of which can greatly influence the cost of driving tunnels. Geophysical techniques can also be ap¬plied to locate deeply incised glacial troughs or ancient buried stream channels that might cross the tunnel alignment. In the meantime, while some researchers continue their efforts to¬ward a breakthrough in new techniques for geologic prediction, it is recommended that other researchers direct their efforts toward sol¬ving specific problems such as accurately predicting ground-water conditions, determining locations of high geostatic stresses, and locations of major fault and shear zones.

Jan 1, 1997

By M. E. Poad, Donald Ross, G. G. Wadell

Because of the "energy crisis" emphasis has been placed on bringing coal mines into full production faster. To accomplish this, more is involved than a rapid excavation system. Mine design should have the freedom within the law to customize as mining conditions dictate as long as the maximum safety of the miner is insured. A year ago, safety was the most prominent "social-human factor"--now, safety and energy self-sufficiency are primary to our national policy. The Single Entry research program as designed satisfies both. It investigates the hypothesis that a single-entry system, for longwall development, supported in the center by open cribs and divided by a fire-resistant partition, can be regarded as being equivalent to or better than a multi-entry system. This paper provides an explanation for the use and advantages of a single entry system in development for longwall mining, explains the problems anticipated with single entries and presents the research approach needed to evaluate and solve the problems. Under study are ground control, ventilation, fire and explosions, emergency procedures, and industrial hazards. Described are measurements data on crib and roof bolt loads as entry heading advances and longwall abutment load is superimposed, stress field determinations and preliminary structural analysis of the double and single entry, and methane liberation and ventilation records as entry advances. Some of the mine operation problems and waivers of mining laws will be discussed. This project is a complete system study having progressed approximately two years in a five-year program.

Jan 1, 1974

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By Z. T. Bieniawski

Results of in situ investigations are discussed providing comparisons of rock mass deformability measurements by three methods: 'petite sismique' technique, the Goodman borehole jack and flat jacks. The tests were performed in exploratory tunnels constructed for site characterization purposes of an underground hydro-electric scheme. Due to the large number of data (41 petite sismique measurements, 45 Goodman jack tests and 19 flat jack measurements), it was possible to evaluate thoroughly the testing techniques employed. The purpose of this paper is to indicate the problems encountered in the interpretation of the results and to offer suggestions for selecting in situ tests. INTRODUCTION In situ tests are expensive and time consuming but they are an important aid in tunneling applications since they can provide deformability data of rock masses in contrast to rock material characteristics obtainable from small laboratory specimens. Some in situ tests are relatively easy to perform but their reliability may be in question unless a comparison of the data obtained by several different test methods is possible. Although many in situ techniques are available for determination of rock mass deformability (1), those more convenient to use are the Goodman jack, flat jacks and 'petite sismique. These methods are considered convenient because the Goodman jack is a borehole device; flat jacks can provide not only deformability data but also information about the stress field around excavations; while 'petite sismique' is based on seismic refraction surveys. Accordingly, these three methods have been selected for comparison.

Jan 1, 1979

By Arthur E. Lord, W. Martin McCabe, Robert M. Koerner

Following the driving of each new section of tunnel, a prompt decision is required regarding the type and extent of primary support to control convergence and prevent ground failure. Sometime thereafter, the effectiveness of the in-place support must be evaluated over the entire length of excavation. It is therefore extremely desirable to have available a lightweight, portable, easy to install and interpret, cost effective monitoring system to assist with these ground control functions. Such a system can be assembled based on the acoustic emission (or microseismic) technique. This monitoring technique uses a piezoelectric transducer to detect subaudible noises associated with deformation of and/or crack propagation in the soil or rock being monitored. After detection, the signals are then amplified, filtered and electronically counted to provide a quantified assessment of the stability of the structure. In the simplest sense, the absence of emission, or counts, signifies no deformation and thus stability. Conversely, the occurrance of counts signifies instability to varying degrees. The higher the count rate, the greater the instability and the need for immediate or additional support. Described in this paper is an overview of the acoustic emission (microseismic) method, details of its use in a laboratory study measuring convergence and stand-up time in soil, and the behavior of rock samples under similar stress conditions. Field use of the method is recommended for ground control monitoring in tunnels, and some suggestions regarding monitoring procedure are presented.

Jan 1, 1979

By J. F. T. Agapito, J. B. Page

This paper describes part of a geotechnical study based on stress determinations and convergence measurements conducted to assess the long-term stability of an experimental room-and-pillar oil shale mine. A rock mechanics program was initiated in 1971 at the Colony Mine as part of a large study conducted for the design of a commercial operation. The Colony Development Operation is a joint venture currently consisting of four active members; Ashland Oil Inc., Atlantic Richfield Company (Operator of the project), Shell Oil Company, and The Oil Shale Corporation. Although oil shale commercialization plans are presently suspended, rock mechanics instrumentation has been continued as part of Colony's policy in maintaining readiness to proceed with a commercial shale oil plant when national energy policies became better defined. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 200 miles west of Denver. Experimental mining operations were conducted from 1965 to 1972 with one of the major objectives of the pilot mine being the assessment of opening and pillar sizes for the determination of extraction ratio and life of the property. Mining was conducted in a 60 foot thick portion of the Mahogany Zone in the Parachute Creek Member of the Green River Formation, at depths of 600 to 850 feet by a one-bench system. Pillar dimensions were 58 feet by 58 feet and rooms were 55 feet wide.

Jan 1, 1977

By J. A. Herbst

Mineral liberation modeling can be traced back to the early work 0fA.M. Gaudin up through more recent population balance modeling by R.p. King, J.A. Herbst and G.T. Adel. A more micro-scopic look was taken at the University of Utah in the form of the J.E. Sepulveda and J.D. Miller Pargen model which permits the creation of an arbitrary shape, multiphase particle made up of discrete grains. Recent work on image analysis and tomographic analysis by J.D. Miller and C.L. Lin have laid the experimental ground work for model validation, but until now it hasn't been possible to include the necessary physics of the particle stressing process to allow the development of a 'ffirstprinciples"mode1 which does not presuppose a "mode” of liberation (e.g., random or by detachment). Recent developments in discrete grain breakage (DGB) modeling now make a generalized physics based model feasible. This paper describes current work that is being done to develop a physics based discrete grain liberation (DGL) model. Two-dimensional and three dimensional simulation results exploring the effects of particle size, phase properties and loading type are presented. Relationships between energy based liberation efficiency, degree of random liberation and material properties are identified.

Jan 1, 2005

By William E. Lamont

The Mineral Resources Institute (MRI) of the School of Mines and Energy Development (SOMED), University of Alabama conducted studies to determine the potential for upgrading the Eastern Devonian shales by flotation. Results of those studies indicate that flotation concentrates containing 150 liters of oil/t (36 gal/t) can be produced from shale containing 50 liters of oil/t (12 gal/t) as determined by Fischer Assay with good recovery of the kerogen. Organic carbon and trace elements such as molybdenum, vanadium and uranium also are concentrated with the kerogen. Kerogen concentration was found to be a function of the size of grind.

Jan 1, 1983

By W. Choi

The present study revealed that the bioleachability of a chalcopyrite flotation concentrate is influenced by the semiconductor properties of CuFeS2. The overall reaction of biooxidation,

Jan 1, 1991

By Thomas E. Krakowski

INTRODUCTION This paper presents a method of calculation of internal moments and thrusts in tunnel liners of any material. The method is intended for hand calculation, but as it is numerical in nature it can be programmed for use in computers. The information required for design or analysis is presumed active internal and external pressures, the effective moment of inertia and cross-sectional area of the tunnel liner, the liner's modulus of elasticity, and the coefficient of subgrade reaction of the material surrounding the tunnel. Starting with active external and internal pressures and following the procedure described herein using the structural properties of the liner and surrounding medium, external passive reactions and internal moments and thrusts are calculated. The method is intended for use by design engineers. GENERAL Experience has shown that flexible tunnel liners have less internal bending stresses than those calculated using classical structural theory applied to free-standing arches. In fact, liners which are very flexible in relation to the surrounding soil or rock have virtually no bending moments when compared to free-standing arches supporting equal active loads. In order for this phenomenon to occur, the original active pressure diagram must be "modified" by additional external reactions (passive pressures) from the surrounding material, so that the thrust line within the lining follows the centroid of the tunnel arch more closely than that of a similar free-standing arch. These passive pressures are reactions developed through outward deflection of the tunnel liner. Thus, the outward moving portions of a

Jan 1, 1979

By V. Roze, M. E. A. Robertson, C. J. Sharland

Current Techniques - Fire Assay Fire assay of gold has been used for several thousand years and is a well known technique to the traditional assayer. Very few assayers wish to use the method but to date there has been no viable alternative. Fire assay is expensive in labour, time, capital and running costs. Workers can be exposed to hazards and uncomfortable working conditions such as lead fumes, heat stress, dust and eye strain. The high capital cost of putting up the building and equipping it, together with running costs which increase annually at a prohibitive rate makes the technique less attractive each year. The main requirement in most assay laboratories is to maximise throughput economically. This is difficult with fire assay as it is impossible to automate. Each sample for analysis is handled by at least 12 people and each person represents a potential source of error. Record keeping and report generation has to be done manually which is both slow and prone to errors. Replacement of staff requires a considerable training period and with a large turnover of personnel this presents yet another problem. The presence of silver and dross in the gold sample affects the accuracy at low gold values. X-ray fluorescent analysis Two methods of XRF instrumentation have been used with limited success. The first type is a laboratory instrument employing L X-rays. Small samples of a few grams, which are not representative,

Jan 1, 1988

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

INTRODUCTION Conventional roof support methods such as mechanical and resin bolting provide adequate support for a wide variety of coal mine roof conditions. However, roof falls remain the single largest cause of death and injury in underground mines and seriously hamper production in many operations, demonstrating that these methods of roof support are not universally effective. One of the most recent and successful advances in coal mine roof control has been the introduction of the roof truss. Although past work on roof trusses (Gambrel1 and Haynes, 1970; Sheory, et al, 1973) shows little quantification of this support technique, numerous field examples have been cited where the truss effectively supported roof which could not be controlled by either mechanical or resin bolts (Kegel, 1969). The truss combines the advantages of both inclined roof bolts and post-stressing the roof. However, the full benefits of roof trusses will only be realized when design criteria to optimize support capacity are determined. The number of trusses required for a given roof condition can then be minimized, reducing installation time and making them economically more feasible. The purpose of this research is to develop roof truss design criteria based initially on laboratory studies of gravity-loaded multi-layered photoelastic mine models. Laboratory test results will then be modified where necessary following future field testing. The ensuing relationships should provide the field engineer with a reliable means of calculating optimum truss configuration, capacity, and spacing for a set of known roof conditions.

Jan 1, 1977

By C. A. Pickles, D. Mallette

Silicon nitride (Si3N4 ) is an advanced structural ceramic materia1 which is presently being considered for a number of potential engineering applications, particularly in heat engines, gas turbines, and electronics. With respect to other structural ceramics, silicon nitride has relatively low thermal conductivity and thermal expansion coefficients and a moderate elastic modulus. Thus, during thermal cycling the stresses developed in this material are lower than in other structural ceramics. At the present time silicon nitride is produced via three main processes: thermal decomposition of silicon imide or amide, treatment of silicon tetrachloride or silane vapour with ammonia and nitriding of silicon powder. These three methods of production are discussed with particular attention to the effect of morphology and phase content on the properties of the final product. In this work carbothermal production of silicon nitride has been studied in a high temperature resistance furnace. Compacted briquettes of silica and carbon were produced which were reacted in a nitrogen atmosphere. The optimum reaction temperature and the carbon to silica ratio were found to be 1425OC and ten to one, respectively. The presence of large amounts of ash in the reductant promoted the formation of silicon nitride. The specific surface area of the briquettes did not have a large effect over the range studied in the present work. Briquette seeding with small amounts of Si3N4 was effective in increasing the reaction rates.

Jan 1, 1990

By E. R. Drevdahl

It has been suggested that we at the University of Arizona present a paper covering the origin, philosophy, and results of the College of Mines program in the field of computers and operations research. I have worked with the program since its beginning, and I will try to outline the developments as they have taken place. The formal development of the educational and research program in the field of Operations Research and Computer Applications at the College of Mines, University of Arizona, began in early 1957. During the year, the University offered its first formal instruction in computer programming. This was my first introduction to computers, and it did not take long to realize that this new tool had a potential that could be profitably utilized by the mining industry. In March 6f 1957, the University Computing Center began operations with its IBM 650 computer. This machine was the only computer of this size in the local area at this time, The first programming effort was in machine language and the programming cost could only be justified for repetitive-type of problems. The progress in the computer field moved very rapidly and with the development of the many compiler and assembly programs and the addition of sub routines to the computer library, the scope of problems that could profitably be investigated by computers expanded rapidly.

Jan 1, 1963