Search Documents

By Graham A. Mathieson

The precise definition of an ultimate or economic pit has, over the years, received much attention in the literature on the subject of mine planning. Unfortunately, relatively little has been published in the area of pit sequencing and scheduling--an aspect which is typically of much greater economic significance both during the life of a mining operation, as well as in the evaluation of an exploration project. This paper discusses an overall mine planning methodology with emphasis on the design of an optimal sequence of pit expansions or phases. Although the concepts given are not new, it is hoped that some practical suggestions will be made. The paper will also describe graphical techniques which have been found useful in comparing the merits and impacts of alternate planning strategies and production schedules.

Jan 1, 1982

By M. W. Chanda

This paper presents the development of a rock-creep measuring apparatus using air as the initial pressure source. Servo-controlled machines can and have been used for time-dependent property tests. However, the long-term nature of some tests makes essential the complete independence of stress-maintaining equipment from main power sources or continuously running hydraulic pumps. The main objective of this paper is the development of a creep testing machine that is free from interference arising through power supply interruptions or mechanical maintenance normally associated with many compression testing machines. To achieve this, a compressed-air power source was used to drive a compression ram. A few trial results obtained and analyzed using the transient creep law are in reasonable agreement with the general creep law.

Jan 1, 1993

By F. -U. Schneider, F. Wellenkamp

Based on previous investigations of ultrafine comminution in planetary ball mills, a new centrifugal mill has been developed which permits similar high stress conditions. Because this new type of mill is equipped with an immobile chamber, devices for measuring energy, for cooling the milling vessel, as well as, in continuous operation, for material feed and discharge can be more easily attached than to planetary ball mills. Observations of particle behaviour have shown that, in the case of dry grinding, most of the material is found on the mill walls even after short grinding times. Due to the fact that energy dissipation takes place mainly in the zone near the wall, a grinding system which reduces the amount of ball filling required is at an advantage.

Jan 1, 1995

By R. J. Snow, S. N. Bhattacharya, D. D. Patil

Electrokinetics involves the movement of charged particles or water molecules in an applied dc field. Applications in particle fluid systems include the dewatering of soils, the densification of mill tailings and the treatment of coal wastes. In this paper, a novel application of this technique is discussed, wherein an electric field is applied to a coal-water slurry flowing through a pipe, resulting in lower pressure losses in the system. A unique experimental setup was designed and built to study the effect of an electric field (dc) on the wall shear stress for the flow of coal-water slurry through the pipe. The effect of solids concentration, current strength and pH on drag reduction across the system was quantified.

Jan 1, 2002

By M. A. Mahtab, N. M. Cruickshank, M. T. Wane

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment, and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) microseismic activity. Geophysical and engineering methods for detecting these characteristics are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1987

By M. J. Klishis

This paper presents the findings of a study on roof bolters' hazard exposure. A "micro-analysis" of accident data was combined with ergonomic observations of roof bolter operators to categorize bolting-related injuries and a checklist was constructed. Bolting-related problems were identified as situations that could expose bolter operators to hazards. Approaches to avoid these situations were applied at six mining operations to evaluate specific problems in roof bolting operations. The re-search emphasized the importance of analyzing worker behaviors in the context of mining situations and equipment design problems that lead to human error accidents.

Jan 1, 1995

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone's lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China's dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996

By Ulrich O. Lange

Coal is America's most abundant energy resource. Therefore, it IS logical to assume that coal must be produced in much greater quantifies in order to make the United States self-sufficient, as far as energy is concerned by 1985. However, there are a number of obstacles which have to be overcome in order to achieve such a great task. According to one of the most outspoken American Mining men, there are three major obstacles. Those are: (1 ) Mining technology (2) Public image of the coal mining industry (3) Governmental policy toward the mining industry The following will be dealing with Shortwall Mining, which is a very specific part of mining technology and which might influence the image of the coal mining industry as well as the governmental guidelines, at least to make it easier to live with those guidelines. During recent years the operation of coal mines has been more expensive than ever. Since 1970, the cost of producing coal increased by 30% and the productivity dropped by just about the same amount. Those are alarming signs.

Jan 1, 1975

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica plate and glass sphere in sodium oleate solutions. Hydrophobic forces were observed when the two surfaces were activated by CaOH+ or MgOH+ ions. The force measurements conducted in the absence of the surfactant showed that the activated silica surfaces do not exhibit the primary hydration forces that have been observed between unactivated surfaces. The activation mechanism was studied by calculating the contributions from electrostatic and chemical interactions to the total free energy change. The results suggest that the adsorption of the hydroxo-complexes is controlled mainly by the lateral interactions between the adsorbed species on the silica surface.

Jan 1, 1999

By Anthony W. Garson

Good morning, ladies and gentlemen: It is a pleasure to be here this morning as a representative of Dean Witter Reynolds; one of the foremost international investment firms in North America. My colleague, Hugh Wilmer (who will be speaking to you a little later), and I are involved as research analysts in the research and writing of published reports containing recommendations on the buying or selling of North American and South African gold and silver mining shares. Our talk this morning will focus on the gold mining operating costs of North American and South African gold producers. However, I am not going to bore you with reams of statistics on the operating costs of large numbers of gold mining operations; how meaningful would this data be to you? Instead, I will discuss what the investor should look for, and how he should use this knowledge in making his investment decision.

Jan 1, 1984

By Tom Ireland, Sumi Eratne

The approach to Risk Management during the procurement of major projects often has a significant outcome on the ultimate successful delivery of a project. The $NZ4.4B Auckland City Rail Link project is the largest and most complex transportation project yet undertaken in New Zealand. Risk management prior and during procurement was undertaken in accordance the ITIG Code of Practice for Risk Management of Tunnel Works (TCoP) and through the use of an Alliance Geotechnical Baseline report. This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. This included the use of cloud-based delivery of geotechnical data and 3-D geological models, reducing tendering costs and allowing a focus on risk mitigation measures during the tender rather than data management.

Jun 13, 2021

By Nikhil Dhawan, Shrey Agrawal, SHAILA MIR

The current study investigates the effect of microwave processing on low-grade banded iron ore using charcoal, coking coal, and non-coking coal. Charcoal showed better microwave heating response at low temperatures, and the coals exhibit better heating response at higher temperatures. Low carbon dosage ~ 12% is sufficient to generate concentrate with 61.8% iron grade and ~6% for 94.8% iron recovery comprising of magnetite phase suitable for iron-making applications. The process separation efficiency of ~ 95% is achieved at 6% carbon dosage and decreases with an increase in carbon due to formation of the fayalite phase. The metallization degree showed a strong dependency on reductant dosage and achieved amaximumvalue of 22.7%at 18%charcoal. The comparison of ore with pure iron oxide and the synthetic mixture of iron oxide indicated that the underlying bonding due to banded structure enhances the Joule heating during microwave irradiation and thereby aids in attaining higher temperature and better separation.

Sep 21, 2020

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982

By R. Owen

The vision-based approach to process control involving fine particles in harsh on-line environments is discussed in this paper. The sensor equipment at the process location, consisting of a light source and a CCD camera provides RS-170 B&W video output. The video can be seen on a process monitor in the control room and is sent to a computer based Vision Processor. The Vision Processor contains a video digitizer and Canty developed software that extracts process information. The iron mine application controls thickener agent feed rate and thus settling pond overflow clarity. The sensor is mounted in the overflow flume of the outdoor settling pond and is used year around in the Minnesota weather. Alternate control system needs a low flow water sample which is subject to freezing in winter. The computer based vision processor provides 4-20 mA analog outputs for real time control as well as file archive for a history record.

Jan 1, 2001

By Wm. I. Weisman

Sometimes in assessing where we are and where we are going it is informative to take a look at where we have been. Whether or not it adds to our understanding of the present, I think it may be interesting to review some of the past history of our industry. As a starting point I chose to use the famous Paley Commission Report, formally known as "The U. S. President's materials Policy Commission -Resources for Freedom."(l) The Paley Commission report said "Fluorspar is an essential raw material for the steel, aluminum, and chemical industries." Of course this statement is still true. It also said, "United States known reserves of fluorspar would be sufficient for some 15 years at present rates of consumption--about 426 000 short tons in 1960. Projected consumption for 1975, however, is several times as great, and reserves in other free countries do not appear adequate to supply United States deficiencies during the next 25 years." This simply demonstrates how even the most learned and competent people can observe all the facts avail-able to them at a given time and yet be unable to predict the future very accurately. We all know that reserves in other countries are more than adequate to supply the United States today, 25 years since the report was published. In fact, the report estimated free-world reserves at something over 36 million tonnes (40 million short tons). Contrast this with 246 million tonnes (271 million short tons) estimated as total world reserves from the section on fluorspar from Commodity Data Summaries of 1974, published by the Department of the Interior. (2) The Paley Report discusses other matters pertaining to fluorspar that are still of interest, such as improving mining methods. Furthermore, it certainly did a good forecasting job in noting that greater recycling should become possible in the aluminum industry in regard to fluorine lost in wastes and also concerning the substitution of fluorspar in the steel industry by other fluxing materials. It also suggested that non-fluorine containing propellants should be investigated as a replacement of those containing fluorine as a conservation matter. Some discussion was devoted to recovering the fluorine content of phosphate rock, which is being practiced today, but was in its infancy in 1950.

Jan 1, 1978

By P. Schilizzi

The increased impact of mining subsidence in the U.S. coalfields and the recent regulatory constraints legislated by government and state agencies have provoked an intense research effort on this topic by government agencies, coal companies and academic institutions. Subsidence and horizontal strain predictions are a basic requirement if subsidence and its associated effects are to be controlled and contained within acceptable environmental levels. As a result, several such prediction techniques have been proposed or are currently under development to assist coal operators in minimizing the detrimental effects of these surface deformations. VPI&SU has been actively involved in this research effort in the past few years, with particular emphasis on the Appalachian coalfield. During the initial stages of this research a large number of subsidence case studies were collected from the literature, the coal industry and government agencies. In total, data from 32 longwall panels and 60 room and pillar panels were collected. This data bank was used to determine relationships between the basic mining and subsidence parameters, in order to allow the evaluation of the various prediction methods for the Appalachian coal region. Based on this data two subsidence prediction techniques, one based on profile functions and the other on influence functions have been developed. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. The limitations of the data of the collected case studies, i.e. accuracy of surveys, frequency of monitoring, lack of horizontal movement measurements, etc, led VPI&SU to the initiation of a detailed subsidence and strain monitoring program above a number of active mines, located in three major coal producing counties of Virginia. The aim of this program was to enhance the data base with accurate and complete measurements of surface movements and to allow, therefore, the refinement of the prediction techniques. This paper presents this monitoring program, discusses in detail the results obtained from three specific case studies and provides recommendations for the implementation of the field data in the general prediction methods.

Jan 1, 1986

By Isabel Barton

This article describes and analyzes the history of research into the origins of the uranium-vanadium(-radium) deposits of the Paradox Basin. For several decades after their discovery in 1881, research was desultory and almost entirely descriptive, fluctuating with demand for vanadium and radium. Systematic geologic descriptions, accumulated between 1910 and 1950, supported rapid progress during a government-backed surge of research in the 1950s, when uranium was the chief commodity of interest. Most of the major theoretical innovations date from this decade, including the use of concepts from solution chemistry to identify the conditions and constrain the processes of deposit formation and alteration. Research from this time was highly influential in geology at large, providing the model for sandstone-hosted uranium deposits worldwide and numerous new minerals and mineral structures. After about 1960, mine production remained high but research dwindled, and most new advances were to the details of the hydrothermal model of ore formation rather than its core concepts. By the end of the 1960s, the deposits were understood to have formed at the mixing interface of an oxidized, metal-bearing water with a reducing fluid of debated origin. Research was desultory over the ensuing decades; the source of the metals and the nature of the chemicals constituting the trap were not clearly established. They remain questions today, as do factors like the relationship between ore mineralization and the geologic history of the basin. (More in the full paper.)

Jan 1, 2025

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By Ronald Ludchak

Since coal has been designated as the short-term answer to the threatening world energy crisis, improved surface mining techniques, along with improved extraction and handling equipment, are needed to increase the amounts that can economically be mined by open pit methods. A dwindling supply of low cost oil and gas have dictated a major rethinking of our energy sources and their use. New methods for open pit coal mining have to be found to increase coal production and to meet more stringent reclamation laws. Modern twin-engine elevating scrapers can play a vital role in meeting these needs. They are readily available, with short delivery times, from several experienced manufacturers of earthmoving equipment. Recent developments of the elevator system have extended its working range to include many of the materials commonly encountered in open pit mining. The paper deals with the advantages of using twin-engine elevating scrapers in the performance of various mining tasks. These tasks range from utility work to the major task of using the scrapers as a primary stripping toot and, of even more importance, a stripping- reclamation tool for, with scrapers, the overburden can be moved and redeposited in the same strata sequence or soil horizon as in its natural state. A recap of current applications of the elevating scraper will be presented, along with proposed uses.

Jan 1, 1975