Search Documents

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By Bee R. Waples

The Alimak Raise Method, using the Alimak Climber, has proven to be a new, fast, economical method of driving raises at the Iron King Branch of Shat-tuck Denn Mining Corporation, Humboldt, Arizona. In order to fully understand the advantages of the Alimak Raise Climber, it is necessary first to describe the basic machine; second, a complete cycle of a raise round; and third, the comparative speed and economy afforded the Iron King operation by using this new method of raise driving: The raise climber consists of a drilling platform that is raised and lowered by two 6.2 HP compressed air motors that drive, through roller chains and sprockets, three worm gears connected in series. These worm gears drive pinions which grip the guide rail rack. The worm gems are fitted with spring-loaded couplings so that a small rock or grit in the rack is passed over without disturbing the mesh between the rack and the other pinions.

Jan 1, 1961

By J. J. Gusek

An 81 hectare (200 acre) tailings impoundment at a taconite operation in Wyoming that ceased operations in 1983 has been a source of blowing dust. The site qualified for reclamation under Wyoming's Abandoned Mine Land (AML) reclamation program. The ultimate reclamation construction included: incorporating commercially available organic amendments and fertilizers into a 300 mm (12 in) thick "cap" of a sterile clay loam cover material, lowering the water level in an adjacent flooded mine pit that was feeding uncontrolled seeps into the tailings basin, constructing a wide tailings pond spillway that allows flood control while minimizing seasonal water level fluctuations in the pond, and building rock berms and rock snow fences for wind erosion control and soil moisture preservation. Tree planting in the protective wind/snow shadows of rock berms and rock snow fences, and the plugging of a decant pipe are planned for future work.

Jan 1, 1998

By R. H. Lesernann

Copper has held up extremely well as we have moved through the trough of the economic cycle. In the aluminum, lead and zinc industries at least half of the Western World production was unable to cover its operating costs at the prices prevailing throughout most of 1991. In copper, less than 10 percent of production ran in the red last year. Most of that was in Peru where the government has not allowed its currency to devalue at the same pace as inflation. Thus, mining company revenues in local currency terms have risen very modestly while costs have escalated tremendously. Excluding such governmentally imposed distortions, virtually every mine in the Western World ran at a profit last year. While copper producers have to be extremely happy about staying in the black through the trough of the consumption cycle, consumers have to be worried. They must be asking themselves, "If copper held at over $1.00 in a year when consumption declined, how high will prices go when demand picks up?" Consumers are accustomed to paying high prices at the peak of the cycle, but they are also accustomed to paying low prices at the trough of the cycle. What went wrong this time?

Jan 1, 1992

By Sergio Godoy P.

The Los Bronces porphyry copper deposit is located in the high Andes of Central Chile. Ore is mined from several tourmaline breccias and from an earlier porphyry. After years of experience in the geostatistical estimation of reserves in different zones of the ore body, we believe that success lies in considering the evaluation as an integrated process beginning with the analyses of the drilling density and sampling methodology, ending with the critically important reconciliation between the estimated and the actually extracted ore, in general, when errors or differences occur, focus is centered in the calculation stages of geostatistics. However, this paper demonstrates that all the evaluation stages are equally important and require the direct and continuous geologic input to ensure the best possible estimate within the frame of the geologic constraints.

Jan 1, 1992

By C. E. Jordan

The Tuscaloosa Metallurgy Research Center of the Bureau of Mines, U.S. Department of the Interior, is investigating the recovery of phosphate from beneficiation slime, as part of the Bureau's efforts to conserve mineral resources through increased use of wastes. Phosphate equivalent to about two-fifths of U.S. production is discarded annually in the wastes. Exploratory flotation tests on the plus 5-um fraction of a slime sample showed promise for a classification-flotation technique. Onsite classification tests at six phosphate washing plants were conducted with a two-stage hydro cyclone system designed to recover the plus 5-um material. The cyclone underflows contained 8.3 to 19.1 percent P2O5, and the recovery of the plus 5-um PZOS values ranged from 81 to 95 percent. The percent P2O5 recovery from the total slimes ranged from 38 to 47 percent. Batch-flotation studies are currently being conducted.

Jan 1, 1978

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

Investigation and uptake of filtered tailings continues to grow throughout the globe. This is driven by a wide range of site-specific considerations, which include such factors as tailings characteristics (e.g., amenability to filtration), production rates, climate, water availability, cost drivers, environmental requirements, and social factors. Despite the aforementioned technological growth, the currently available filtration technology is not able to meet the needs of many operations and projects that would otherwise adopt the technology. Experience with large-scale industrial filtration shows that vacuum belt filter systems meet the needs of many modern users, exceptions being the inability to effectively dewater tailings at altitude and/or with a fine particle size distribution: a potential fatal flaw. This paper presents a case study on the utilization of the patented Viper Filtration technology on gold tailings to overcome this challenge and shares the resultant full-scale plant design, highlighting the features designed to overcome cost and scalability deterrents. This technology is a novel mechanical process which complements the vacuum pressure in dewatering the filter cake as it travels along the belt filter. This project commenced with a pilot testing program, which successfully met the objective to rigorously test, measure and record any performance improvements achieved when engaging the Viper technology. Of the two tailings products tested, gross improvements of 4.2%w/w and 5.7%w/w were achieved when compared to the conventional vacuum belt filter operation. This pilot testing facilitated measurement of operating and design data, which forms the basis of the full-scale system design and resultant equipment supply of three vibration roller assemblies for retro-fitting on the existing vacuum belt filter.

Jan 25, 2021

By W. H. Renison

This paper will discuss the operation and maintenance of Molycorp's Quests Mine ore conveyor system. The 1.2 m wide, steel cable-reinforced conveyor belts are capable of transporting 1089 kt/h of ore over a belt line distance of 3124 m with a vertical rise of 518 m. A portion of the conveyor runs in a 2057 m long underground decline on a 10° slope. Six 448 kW motors power the main 1.2 m wide belts.

Jan 1, 1984

By Vincente M. Jr. Lim, Brain W. Lawrence

Underground mining operating costs consist pri¬marily of direct costs such as labor, supervision, ma¬terials, and supplies, plus indirect costs. The material and supply costs vary substantially between mines but commonly range from 35 to 60% of the total direct costs. As part of the preparation of accurate operating cost estimates for a project, information must be as¬sembled to select the material and supply items and to determine the quantities of these items that will be required. Cost data then can be incorporated with the estimated material and supply requirements to determine the total material and supply costs for the project. Estimated quantities will vary considerably between mining projects depending upon factors such as the type of material being mined, the mining method, the equip¬ment selected, drilling and blasting techniques, mucking and haulage methods, ground support requirements, number of men employed, etc. Valuable information often can be obtained from suppliers and manufacturers, including data on current operating practices for similar projects, recommenda¬tions for the specific project, and preliminary cost quota¬tions. However, quotations obtained for estimates are generally higher than the prices paid at the time of purchase. Mines operating in the area, or those mining under similar conditions, also can provide essential design information, but it often is difficult to obtain cost information from the operators. Estimated costs for the most common major items of underground materials and supplies are presented in the accompanying tables. They represent current costs or cost ranges and are intended to be used only as a guide when preparing budgetary estimates for materials and supplies. Cost data were obtained mainly from suppliers and manufacturers, with up to three quotations being ob¬tained for each item whenever possible. In most cases, as noted in the table footnotes, prices were based on quantities representing normal requirements for me¬dium-size mine operations. Every attempt was made to assure accuracy. However, the cost for most items, especially those with multiple sources, can deviate sig¬nificantly for various reasons such as geographical loca¬tion, current market conditions, quantities ordered, size of the customer (which could influence the ultimate quantities purchased), and the ability of the purchasing department. It is also for these reasons that the actual amount individual mines are now paying for specific items may vary from the estimated cost in the tables. The cost for specific sizes of items that do not appear in the tables often can be factored from the data pre¬sented. Costs for many items can be converted easily to a unit that sometimes is more basic, but not as com¬monly used, such as from a length to a weight unit. Other items not listed, such as repair parts for equip¬ment, will involve contact with suppliers to determine specific recommended requirements and to obtain costs for these items as related to each individual project. Costs are expressed in terms of US dollars as of 1978 unless otherwise specified. All measurements, sizes, and weights are expressed in conventional units (i.e. feet, inches, pounds) ; applicable metric conversion fac¬tors follow each table. Costs are represented for drill steel and bits; mining explosives; blasting caps; blasting supplies; ground sup¬port items; ventilation equipment; utility pipe, utility hose, and accessories; mine track and accessories; tires for underground equipment; lubricants and fuels; and miscellaneous supplies.

Jan 1, 1982

By J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc., and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the 'New Missouri Lead Belt' (See Figure 1). Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated about 1,100 feet below the surface at an elevation 270 feet above sea level, the flat lying sinuous ore bodies are up to 250 feet wide, 85 feet high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite, Access to the mine is through two 18'Ø concrete lined vertical shafts - one for servicing and the other for hoisting ore (See Figure 2). The mine is being worked by a modified room and pillar method using both rubber tired equipment and a sub-level rail haulage. Ore is broken from first pass headings, back and bench faces and transported by load-haul-dump units to ore passes located on 900 foot centers. The ore is pulled from chutes on the sublevel 90 feet below into 15 ton bottom dump cars and delivered in 10 car lots by a 15 ton diesel locomotive to a 42" gyratory crusher (See Figure 3). A recent innovation has been the introduction of two 50 ton trucks with plans to haul up to 60% of the ore on the mining level to an ore pass feeding directly to the primary crusher (See Figure 4). Ventilation raises up to 16'Ø, which were originally planned for 900 foot centers, are now driven on 450 foot centers.

Jan 1, 1973

By Hugh Jones

Mine planners are challenged to hold two seemingly opposing objectives: maximizing the mine?s operational efficiency while minimizing post-closure impacts. One of the most effective approaches to meet these objectives is to plan for mine closure from the start. Mine closure is typically viewed as the process that happens in the period of time when the operational stage of a mine is ending and the final decommissioning and mine rehabilitation is being undertaken. In reality, it is a continuous series of activities that begins with preplanning prior to the project?s design and construction and ends when long-term site stability is achieved and a self-sustaining ecosystem is established. Putting this model into practice as early as possible can significantly reduce the financial burden of mine closure and rehabilitation.

Jan 1, 2011

By E. R. Mueller

The natural lives of machines and components vary tremendously! Maintenance managers struggle constantly to maximize their equipment lives while minimizing their maintenance costs, but they normally lack the tools and techniques they need to do this properly. This paper proposes a methodology based on probabilities of failure and expected values for repairs that recognizes the variation among individual machines and components as well as the high costs associated with catastrophic failures. It enables a user to determine the optimum change-out intervals for many types of equipment. The approach proposed here is sophisticated enough to be reliable but simple enough to be applied by the maintenance staff on the shop floor. It will complement existing preventive and predictive maintenance programs.

Jan 1, 1995

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By Andrew R. Thomas

As the demand for most industrial minerals on the world market continues to climb, educational institutions maintain traditional policy in emphasizing chiefly metallic ore deposits and energy resources in addition to the general disciplines. In spite of their increasing importance, few universities exhibit great depth with respect to industrial minerals courses due to the shortage of specialized faculty in a category this broad. As new ideas are formulated and technological advances are developed in the field of industrial minerals, the classroom still exists as a student's primary source of information. This opportunity to give today's students the benefit of modern developements has not been utilized to its utmost potential.

Jan 1, 1981

By H. Colijn

Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units, such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. A feeder can do many things, but it should never be considered a suction pump: During the past few years various papers have been written and presented on feeders and their application. 1,2,3,4,5,6,7,8,9)* It is not the intent of this paper to cover the same ground, and the readers are therefore ad¬vised to consult the referenced publications for supplementary information. This paper will be confined to some specific design criteria of bin feeders, such as feeder load and power requirements. Special attention is given to the basic design criteria of vibratory feeders.

Jan 1, 1968

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study adsorption of sulfide collectors such as modified thionocarbamates and thioureas, xanthate, dithiophosphate, and dithiophosphinate, on galena, chalcocite, chalcopyrite, and quartz under flotation related conditions. In the case of the adsorption of modified thiourea on chalcopyrite, chalcocite and Cu-activated quartz, and of dithiophosphinate on galena, SIMS measurements have provided direct evidence for the presence of metal-collector (1:1) complexes on surfaces. In the other systems, only the collector molecular ion and its fragments were detected. The distribution of adsorbed species on the surfaces was obtained by using SIMS in the imaging mode. On chalcopyrite, only the copper-collector complex was found; there was no evidence for iron-collector complex. In the case of quartz, adsorption of selective collectors was observed only after activation by copper ions.

Jan 1, 1996

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By Kadri Dagdelen, Lee J. Zamalloa

Truck-shovel dispatch systems based on linear or nonlinear programming algorithms have been in operation since the mid-1980s, with different levels of success depending on the correct arrangement of operational resources and the complexity of the mine. These systems are known for shortcomings related to the logic behind the decision-making of the operational objectives. This makes it necessary to have a human agent (dispatcher) to guide the system when the operational parameters change, creating the possibility of suboptimal decisions due to the human factor. To address this issue, the present work discusses the implementation of a methodology based on artificial intelligence (AI) techniques to assist in the decision-making of the best optimization goals arrangement when operating a fleet management system. The focus of the analysis is on the evaluation of variable goal weights in a nonpreemptive, multigoal optimization model for multiple uncertain scenarios based on regions of optimal feasibility.

Apr 1, 2025

By M. Birdsell

"Sustainable long-term restoration requires adequate planning and preparation, implementation, and measurement goals to monitor success associated with restoring sites to pre-disturbance levels of ecological health. The Buckhorn Mountain Mine riparian habitat restoration project has been a multi-year endeavor with a variety of restoration techniques implemented by Kinross Gold/Crown Resources Corporation. INTRODUCTION The Buckhorn Mountain Mine procured mitigation lands during the permitting process to be set aside for long-term restoration. A portion of this mitigation land included three aquatic habitat mitigation parcels; a spring and wetland complex and two stream and riparian corridors. These properties were historically used for agriculture purposes and livestock grazing. During initial permitting, habitat monitoring and mitigation plans were created to help guide restoration, and provide measures for success. Various techniques and adaptations have been implemented on the properties since 2007, and continued efforts are being implemented annually to ensure the long-term success of the project. Field measurements are collected annually to ensure mitigation objectives are being met, and provide opportunity to modify restoration efforts when necessary. MATERIALS/METHODS Restoration efforts have included implementation of several methods including livestock exclusion, treatment of state and locally listed noxious weed species, installation of regionally sourced riparian plant species and local stock willow cuttings. Annual mechanical and herbicide treatments for noxious weeds have been conducted annually. Efforts to control reed canarygrass (Phalaris arundinacea) have been implemented since 2013; methods include mechanical and herbicide treatments. A combination of methods has been employed to help aid restoration of native species within the riparian corridor, and increase survival of planted species, including weed matting and browse barriers to aid riparian planting success. Instream planting of local stock willow have also been employed to increase stream vegetative cover and provide long-term bank stabilization. Most recently, a perched culvert near one of the properties has been replaced with an aquatic life passable culvert designed to aid in the upstream migration of fish species into the stream system. Efforts to provide increased fisheries into upstream portions of the system and aid in restoration of stream bed and bank have been employed to increase the ecological value downstream of the replacement. In addition to efforts completed by the client to provide restoration efforts, a local non-profit organization, in conjunction with the client, installed beaver dam analogues (BDAs) in the fall of 2014. These structures are intended to raise water levels along stretches of incised channel in an attempt to flood historic off-channel floodplain"

Jan 1, 2016