Search Documents

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By Maryam Motamed, Jeremy Stone, Leigh Anne Zhang

Controlling and predicting ground movements are essential to the design of shoring systems. The Courthouse Commons tunnel in San Diego, California, included a 56-foot-deep temporary shaft as a launching point for tunneling using the Sequential Excavation Method (SEM). The rectangular shaft was unique in that it was surcharged on one wall by an 11-story building and employed a hybrid support of excavation design. An array of geotechnical instrumentation was used to monitor lateral and vertical movements at the ground surface. This paper compares the measured ground movement with the predicted ground movement from various excavation stages

Dec 1, 2022

By W Medina, G Angulo, A Anani

A current challenge faced by the mining industry is solving the integrated transition mine problem (TMP) that maximizes the net present value (NPV). This study aims to develop an optimization framework capable of solving the TMP. The problem is NP-hard and therefore computationally intractable. Three ad hoc approaches – Exact solution, Benders’ decomposition, and Benders’ decomposition with Bienstock-Zuckerberg (BZ) algorithm – are compared for different scheduling periods. The TMP is formulated as a mixed integer linear programming model, implemented in Python, and solved with the Gurobi optimizer. The results showed that Bender's decomposition with the BZ algorithm outperforms the other approaches in execution time, computational cost, and feasibility to address large problems in exchange for a marginal cost in the quality of the NPV obtained. In addition, the probability of finding the optimal point of transition is higher regardless of the number of feasible crown pillar locations evaluated. This is achieved through the optimality cuts proposed in the algorithm.

Jun 25, 2023

Microorganisms have been widely used for hydrometallurgical operation and effluent treatments(Smith, et. al., 1991a; Gadd, et. al., 1986; Darnall, 1986; Paponettis, et. al., 1991; Mihaylov, et. al., 1991; Rusin, et. al., 1991; Noble, et. al., 1991; Yang, et. al., 1991). In recent years there is a growing interest in using microorganism for flocculation of minerals fines and flotation collector (Smith, et. al., 1991b, 1991c; Misra, et. al., 1991a, 1991b, 1992a, 1992b). It is envisioned that the utilization of nonpathogenic microorganism and/or extracellular surfactant derived from microorganism as a flotation collector will replace some of the environmentally toxic flotation collectors and at the sometime improve flotation efficiency. The selection screening, and judicious selection of appropriate microorganism as flotation collector has been a challenge to process engineers. Over the past five years, continued research at the University of Nevada has shown that certain microorganism Mycobacterium phlei (M. phlei) can be a good flocculating agent and has potential to be used as a flotation collector (Dubel, et. al., 1992; Misra, et. al., 1991a, 1991b, 1992a, 1992b; Smith, et. al., 1991d; Chen, et. al., 1992a, 1992b)).

Jan 1, 1993

By Furuyama Takashi, Mori Sukeyuki, Hara Tsuyoshi, Fukushima Yujin

In mineral processing practice, flocculation is largely established as an engineering technique of waste water treatment and the study of parameters increasing the settling velocity of particles is still of great importance to improve the process. Further investigations were made using quartz (Q89) and fluorite samples (F91) which included 58.8% and 65.8% of -2.3 µm particles respectively. In all the experiments the flocculation phenomena were observed varying the pH value of the aqueous suspension. In contrast to quartz particles (Q89) which did not flocculate for all pH values, it was, noticed that fluorite particles (F91) flocculated in the alkaline range of pH over 11. With an aqueous suspension containing equal quantities of Q89 and F91, a hetero-flocculation of particles was observed at a range of pH below 10. In this case, the maximum floc size of the hetero-flocculation was 37.0-26.2 µm This size was about three times larger than when quartz (Q84) and fluorite particles (F85) were used with 32.4% and 40.4% of -2.31 µm particles respectively. Besides, in the experiments using Q89 and F91, the maximum size of hetero-flocculated single particles was found to be 6.54 µm instead of 3.27 µm as obtained with Q84 and F85.

Jan 1, 1995

By G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26 million tons of ore of which 16 million is mined and milled on site. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centered around the Pyroxenite ore. This will lead to substantial increases in production costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction, and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people and, in 2024, produced 42.4 million tons of iron ore and 57.9 million tons of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan, and Liberia, focusing on iron ore and coal extraction to support steel production. This study examines Peña Colorada, one of Mexico’s largest iron ore mines (a joint venture by ArcelorMittal and Ternium). Facing declining ore grades, Peña Colorada adopted Hexagon solutions to uncover and capture project value. A comparison of two Life of Mine (LOM) plans from 2012 and 2016 (before and after implementing Hexagon solutions) shows that between 2019 and 2023, Peña Colorada reduced actual waste by 26% (compared to 2012 LOM) and 19% (compared to 2016 LOM). LOM Plans are generated yearly, and each time, opportunities for reducing mining waste were identified, evaluated and implemented. The key driver was schedule optimization using Hexagon MinePlan Schedule Optimizer (MPSO). This reduction means less waste transported to disposal sites, resulting in fewer hauling equipment operating hours, lower fuel consumption, and reduced carbon emissions.

Feb 22, 2026

By C. Braux

The aim of this study was to develop an integrated approach to enable identification of areas favourable for the presence of massive sulphide deposits in a given region (Las Herrerias, Spain). It is based on geochemical soil exploration, geophysical surveying (ground gravimetry), detailed geological mapping and a knowledge of the deposits of the South Iberian Massive Sulphide Belt. The multi-dataset approach consists, in the first instance, in standardizing and combining all the geochemical data with reference to their geological setting. Next, the "heavy" anomalies are extracted from the gravimetric survey, regardless of the surrounding context (heavy or light). The results from these two stages are then crossed, so that areas where heavy anomalies are associated with geochemical anomalies can be identified and classified. Crossing the geochemical and geophysical data enables a much tighter selection of anomalies than does the manual superposition of data provided by each method (geology, geophysics, geochemistry).

Jan 1, 1994

By C. D. Harrison

The 1990 Clean Air Act Amendments specify national objectives for reducing sulfur dioxide emissions from coal-fired power plants System-wide reductions can be achieved by combining various emissions controls technologies and allowances, or compliance credits, that can be purchased, sold, or traded. As part of the Coal Quality Expert development project funded by U.S. Department of Energy and the Electric Power Research Institute (EPRI), Black & Veatch has developed an interactive computer tool, the Acid Rain Advisor (ARA). ARA allows the user to develop integrated system-wide compliance plans by comparing the costs and emissions reduction benefits for emissions allowances and various SO2 control technologies such as coal cleaning, fuel switching, and scrubber retrofits.

Jan 1, 1992

By J. Y. Hwang

Coal cleaning with traditional magnetic separation usually yields unsatisfactory results because minerals associated with coal, such as quartz, clay, pyrite and calcite, are weak-or non-magnetic. Magnetic reagent technology is a new mineral processing technology with the capability to enhance the magnetic property of minerals selectively. This reagent can be adsorbed selectively on minerals through the control of surface chemistry and, thus, result in selective magnetic enhancement. The application of this technology on coal cleaning has been experimentally demonstrated. Good separation results can be obtained at low to medium magnetic field strength. Comparison with other processing technologies is included.

Jan 1, 1992

By Jameel Menashi

Aqueous solutions of Na2Cr04 can be reduced with CO to produce hydrous Cr203 and NaHCO3/Na2CO3. CH3OH, HCOO and HCHO in the presence of CO2 also reduce Cr 6+ and yield similar products. It is shown that the rate of Cr6+ reduction can be represented by the expression -d[Cr6+]/dt=k[Cr6+)1/2[R] where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mole. Rapid reduction rates are attained at temperatures in excess of 220°C and, with these three reductants, a green acid-insoluble readily filterable hydrous Cr203 is formed. With HCHO significant reduction of Cr6+ occurs at about 80-100°C and an acid-soluble violet modification of hydrous Cr2O3 is formed. The reduction process is reasonably selective: solutions of Na2CrO4 contaminated with Mo6+ and W6+ can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels. These findings are utilized as a basis for a process for recovering chromium from secondary source materials.

Jan 1, 1984

By Sihua Lei, Hong Zhong, Shuai Wang, Yu Gan, Zhanfang Cao

High purity MgO is widely used in various fields as an important magnesiumcompound. The separation of Mg and Ca is of great importance for the preparation of high purity MgO from dolomite. In this study, the key effects of carbonization temperature and nano-calcium carbonate agglomeration on the separation mechanism of calcium and magnesium have been investigated. The results indicated that the reaction in the carbonization process was stepwise. Precise control of the carbonization temperature was essential for the formation of Mg(HCO3)2 due to its low reaction efficiency at lower temperatures or decomposition markedly at higher temperatures. Meanwhile, there was a common-ion effect in solutions containing Mg2+ and Ca2+. Nano-CaCO3 particles were formed during carbonization and agglomerated with the prolongation of static time. A product with a purity of 99.56% MgO and 0.16% CaO was obtained under the optimized conditions: ratio of liquid–solid 30 L/g, carbonization temperature 22–25 °C, carbonization time 1 h, and refining time 4 h. This work has important guiding significance for the preparation of high purity magnesium oxide from dolomite.

Apr 21, 2020

By Moussa Wone, Jeff Peterson, Filippo Azzarà, Daniele Nebbia

The DC Water and Sewer Authority's Long Term Control Plan includes tunnels, sewer separation, pumping station rehabilitation and green infrastructure to reduce combined sewer overflow (CSO) discharges to the District waterways. The Northeast Boundary Tunnel is a deep, large sewer tunnel that will reduce CSO discharges; signifi- cantly mitigate known chronic flooding in the Northeast Boundary drainage area and improve the water quality of the Anacostia River. This paper presents the unique combination of Owner and Contractor perspectives of the entire Project from conception through procurement, execution, and contract management, providing lesson learned, chal- lenges encountered, and solutions implemented to deliver the Project successfully.

Jun 23, 2024

By Nick Karl, David Wilburn

"The mission of the U.S. Geological Survey (USGS) National Minerals Information Center (NMIC) is to collect, analyze and disseminate information on the domestic and international supply of and demand for minerals and mineral materials essential to the U.S. economy and national security. Understanding mineral exploration activities and trends assists government policy makers, minerals industry decision makers and research entities in identifying where future sources of mineral supply are likely to be discovered, the amount and type of these resources and factors that may affect exploration and development.This review summarizes significant exploration trends related to active sites and budgets, mineral commodities and regional factors for the years 2001-2015. Data were compiled by specialists in the USGS-NMIC, and reported annually in the USGS-NMIC Minerals Yearbook series and in the May issue of Mining Engineering magazine. External data for these analyses were derived from industry sources, published literature, and SNL Metals & Mining, an offering of S&P Global Market Intelligence (New York, NY).The USGS-NMIC compiled exploration site data for more than 80 mineral commodities, focusing on base metals, diamond and precious metals. More than $138 billion constant U.S. dollars were budgeted by the minerals industry from 2001 through 2015 to explore more than 16,000 mineral deposits globally (SNL Metals & Mining, 2016a). Annual analyses identified where mineral exploration took place by principal commodity target, ranked the magnitude of activity in each region, identified the factors that most affected changes in exploration activity and highlighted developments that led to changes in global supply or increased diversity of supply to the United States. Geographic classifications noted in this report were Africa, Australia, Canada, China, Latin America, Pacific, Russia, United States and Rest of the World."

Apr 1, 2017

By M. N. Herrera

The bioleaching of mineral sulfide pulps in a bench-scale rotating drum reactor has been studied. The reactor includes horizontal paddles in the inner wall for lifting of the mineral pulp. The performance of the reactor was tested in the bioleaching of a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans strain (ATCC 19859). The concentrate was efficiently bioleached at 50% pulp density with the drum operating at 0.5 -1.0 rpm Attempts of bioleaching the concentrate at the same pulp density in conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows to operate at much higher pulp densities than the conventional stirred tank reactor. This behavior is explained in terms of an improvement of the bacterial activity due to a better control of the attrition of the mineral particles.

Jan 1, 1997

By L. Vinnett, J. Yianatos, S. Flores

"A numerical conditioning analysis for mineral recovery estimation was performed for industrial flotation plants, considering the copper (Cu), molybdenum (Mo) and iron (Fe) separability. A modified relative condition number, ?, was presented that allowed sensitivity analysis to be evaluated for the component recovery by means of an analytical formula. This closed form made it possible for the error propagation to be determined from feed, concentrate and tail grades with different orders of magnitude. The ? parameter can be evaluated using available grade data from the design criteria or historical mass balances, in which the variability is typically unknown. Reconciled data from different Cu/Mo concentrators were employed to evaluate the effect of small numerical disturbances in the grade data on the mineral recovery estimation. Higher error propagation was typically observed for Fe. The Mo minerals presented numerical problems, mainly in second cleaners and in the first cell of rougher banks. Lower condition numbers were observed for Cu due to the higher flotation rates.Mass-balance data reconciliation without redundancy was evaluated for a typical Cu/Mo flotation circuit using relative error minimization. Significant relative errors in the mineral recovery estimation were obtained with nonreconciled data in ill-conditioned problems. Negligible improvements in the mineral recovery estimation because of the data reconciliation with regard to the nonreconciled approach were obtained in well-conditioned problems. In addition, the improvements in mineral recovery estimation by using Cu, Mo and Fe in the data reconciliation were nonsignificant with respect to using only the best-conditioned component in well- and ill-conditioned problems.Despite the effort in data reconciliation and data repetition, poor performance may be obtained in ill-conditioned problems, which can deteriorate the flotation rate characterization. The error propagation has a negative impact on the mineral recovery of the first cell, which may significantly bias the flotation rate characterization of both valuable and nonvaluable elements.IntroductionMass balances have been extensively used in flotation processes to determine the mass flowrates (production) and mineral recovery (efficiency) of valuable minerals. Simple relationships for steadystate processes based on the feed, concentrate and tail grades can be obtained by taking a black-box approach. However, the calculation of concentrate flowrates from different components of the system, such as size fractions, chemical elements or minerals, does not satisfy the mass-conservation principle because of measurement errors (Smith and Ichiyen, 1973; Romagnoli and Sánchez, 2000). Mass-balance data reconciliation allows for obtaining a unique solution that satisfies the total and component mass balances, making small adjustments to the process data and taking advantage of the information redundancy (Narasimhan and Jordache, 2000). This methodology, which is based on a constrained weighted least-squares minimization, has proved to be robust when measurement errors are normally distributed, in the absence of gross errors.Commercial software has been developed to conduct massbalance data reconciliation in flotation processes, including MATBAL (Algosys, 2002), BILMAT (Algosys, 2013), JKMultibal (JKTech, 2013), BILCO (Caspeo, 2013) and HSC Chemistry (Outotec, 2013), which accomplish the reconciliation using known data accuracy in the optimization problem. The data accuracy can be obtained by sampling a stream n times in a run, known as repeats, each with independent chemical assays. Some unmeasured variables can be estimated using the measuring redundancy and sensor location. At present, grade and flow rate sensors may be incorporated in flotation to conduct real-time mass balances. However, a lack of sensor calibration and maintenance for suitable online measurements hinders the quality of the information. In"

Jan 1, 2016

By A. Anttila

The grinding mill is probably the most common unit operation used in mineral processing. There is, however, much which can still be done in the way of optimization. This paper discusses the results of a well controlled pilot scale test in which the performance of a tumbling mill with a conventional rubber lining equipped with lifter bars is compared to that with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14 percent more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case the -20 mm ball charge required 26 percent less grinding energy than one with a -30 mm ball charge. The energy savings can. in most cases, be converted to increased capacity. The wear of the grinding media is difficult to assess over a short period test but the results suggest it is somewhat less when a smooth lining is used. The wear of the linings has not been included in this study but it is generally accepted that the use of the magnetic lining reduces the lining costs dramatically. Computer simulation using the Millsoft code, developed by Mishra e.a. confirms and explains the increased effectiveness of comminution when smooth lining and smaller grinding balls are used.

Jan 1, 1998

By Vic Miller

Highly variable milling properties within a geologically complex porphyry copper deposit owned by Kennecott Corporation in Nevada made it necessary to estimate the copper recovery and concentrate grade in areas where actual test data was lacking. The estimation was made by first determining the relationships between the desired metallurgical properties and the ore's petrology (i.e. copper mineral type, rock type and copper grade). This relationship was then combined with the already estimated rock type, mineral type and copper grade data in the mineral block model to predict the milling properties.

Jan 1, 1983

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989