Search Documents

By Walter Steiner, Claus Becker

INTRODUCTION General Switzerland is a densely populated country in the heart of Europe. With its total surface of 41.300 km2 and a population of 6,8 million in 1986 the average population density is 163 capita / km2. The population density is lower than in Germany (245 capita/ km2) or the Netherlands (355 capita/km2). The USA have a population density of 26 capita/ km 2. However, sixty percent of the Swiss surface is covered by the Alps and another ten percent by the Jura mountains the remaining thirty percent of the surface is covered by the Swiss plateau where the majority of the population lives. The population in the inhabitated areas is thus substantially higher and may possibly reach those in major metropolitain areas. Due to the high population density in Europe in general and Switzerland in particular future traffic demands cannot be fulfilled sole by car or plane. Environmental and land-use constraints lead to the third option for growing transportation needs: High-speed rail (Bovy, 1990). Switzerland has developed its own approach to promote public transportation and in particular rail transportation: "Rail 2000" (Stalder, 1990). The system "Rail 2000" is based on a series of hubs distributed over Switzerland where easy connections can be made.

Jan 1, 1991

By B. C. Paul, R. Q. Honaker, K. Ho

Recent research has shown that froth flotation is not effective at treating fine coals (-28 mesh) containing a large portion of middling particles. Due to their relatively large density differences, middling particles can be separated more efficiently using gravity-based processes. The ability of gravity separators to treat fine particles has been limited by the lack of particle inertia relative to the surface drag forces. However, particle inertia can be enhanced by the application of a centrifugal field. A commercial-scale centrifugal Falcon concentrator capable of treating a mass flow rate of greater than 1 tph continuously has been used to evaluate its feasibility for treating fine coal as an alternative to froth flotation. Tests conducted on a -28 mesh fine coal circuit feed have found the Falcon concentrator to be very effective at cleaning the 28 x 325 mesh size fraction. For an Illinois No. 5 coal sample, the ash content was reduced in the 100 x 325 mesh size fraction from about 18% to 8% while achieving a high combustible recovery value of nearly 97%. In addition, the total sulfur content was substantially decreased from 2.6% to 1.7%. The effects of the critical operating parameters on separation performance have been studied and their values optimized.

Jan 1, 1995

By Robert A. Jankowski, J. Drew Potts

The Bureau has identified several ventilation techniques and a water spray application for reducing auger mining dust levels. The dust control methods all work by improving air quantity or flow patterns at the face. Section airflow is maximized by reducing air leakage between entries. Sealing stoppings with brushed- on mortar, containing fiberglass additives, reduces leakage. Heading airflow is maximized by properly installing the brattice curtain and keeping the area between the curtain and rib free from obstructions. The brattice curtains should be hung at least 1.7 m (5.5 ft) from the ribs in 7.9 m (26 ft) wide entries and kept less than 4.6 m (15 ft) from the face. A tight curtain seal is created by using the mine air pressure to force the curtain against the timbers, roof and floor of the mine. Using both a blowing curtain and an exhausting curtain will isolate some face workers from dusty air. The Bureau designed, auger clearer spray system, can be used to force heading air across the active face. Laboratory tests indicate that the auger clearer spray system can increase face velocities by more than 0.5 m/sec (100 ft/min), while using less than 0.13 l/sec (2.0 gal/min) of water.

Jan 1, 1989

By D. B. Sikka, R. B. Bhappu

Porphyry-type copper-molybdenum (Cu-Mo) deposits typically occur in the Phanerozoic rocks and have been well-documented. During the past two decades, a number of porphyry-type Cu-Mo deposits that range in age from 1055 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India. Namibia and Zambia. The Malanjkhand porphyry copper deposit M.P., India is estimated to contain 789 Mt (870 million st) averaging 0.83% copper (mill headgrade); 0.004% molybdenum; 0.2 g/t (0.006 oz/st) gold; 6 g/t (0.175 oz/st) silver and a cap of 7.5 Mt (8.2 million st) of oxide ore averaging 0.8% copper. The economic potential of the expanded copper mining milling, smelting and refining complex is expected to yield cathode copper 118.6 kt (130,700 st); molybdic oxide 830 t (914 st); gold 1.9 t (61,732 oz); silver 46.6 t (1.5 million oz); sulfuric acid 240 kt (264,500 st), copper from leach dumps 11.5 kt (12,600 st); nickel 24 t (26,400 st); cobalt 84 t (92,600 st); bismuth 16 t (17.6 st); selenium 48 t (53 st), tellurium 4.8 t (5.3 st).

Jan 1, 1995

By Raymond A. Povirk, David L. Bartsch, James V. Hamel

The Ohio Valley Coal Company is expand- ing its Powhatan Mine No. 6 near Alledonia, Ohio. This expansion includes a 20 rn (65 ft) height in crease for an existing 44 rn (145 ft) coal refuse - slurry impoundment dam. The dam is being raised by upstream construction which will involve placement of more than 15 m (50 ft) of new fill over an existing reinforced concrete decant structure. This structure is 0.76 rn (30 in.) square inside and its deepest portion was under 24 m (80 ft) of coal slurry and water. The top of the decant structure was not strong enough to safely support the new fill and, because of the slurry and water, there was no way to reinforce the structure from the outside. The structure was reinforced frorn the inside by sliplining 73 m (240 ft) of 0.66 rn (26 in.) OD, 0.53 rn (21 in.) ID polyethylene pipe, grouting around this pipe with cellular concrete. and constructing a steel-fiber reinforced micro-silica concrete transition at the upslope end of the pipe. Rehabilition of the decant structure was completed in August 1989. The rehabilitated decant structure is now performing satisfactorily as fill is being placed over it for raising the dam.

Jan 1, 1991

By Craig J. Nelsen, J. Leroy Schutz

The Carache Canyon Prospect consists of a hypabyssal breccia pipe which intrudes a gently dipping sequence of Cretaceous Mancos Formation and Mesa Verde Group shales and sandstones. This sedimentary sequence is intruded by a number of Oligocene (34-30 Ma) calc- alkaline sills. The formation of the breccia pipe and its subsequent gold mineralization is related to the emplacement of an alkaline intrusive complex dated between 30-26 Ma. An exceptionally large block within the pipe provides compelling evidence that brecciated sills and sedimentary rocks form a relict stratigraphy that collapsed 400-800 ft (120-240 m) below their counterparts outside the pipe without substantial changes in stratigraphic position. Native gold and sulfide mineralization within and around the pipe occurs in fractures that are primarily controlled by competency differences between sills and sedimentary rocks and secondarily controlled by ductility contrasts between the relatively brittle Mancos Formation hornfels and the more ductile Menefee Group shales. The resulting pattern of gold mineralization is a series of stacked, tabular, mineralized sills and sandstone separated by barren shale in an annular region along the southwest margin of the pipe. A series of near-vertical, subparallel, sill and sandstone breccias separated by barren or weakly mineralized shale breccia occur within shallow levels of the pipe.

Jan 1, 1990

For nearly two decades, MINExpo International has held the title to the biggest show in mining. The 2012 MINExpo is expected to be the biggest yet, with nearly 1,800 exhibitors rolling out the newest equipment and services across 12 halls. From September 24 to 26 in the Las Vegas Convention Center, MINExpo will present the newest in everything from automation and robotics to safety and communications equipment to reclamation services, and much, much more. The last MINExpo, in 2008, had nearly 38,500 visitors. The show?s sponsor, the National Mining Association, expects this year will be even bigger, with more than 40,000 visitors over three days. Twenty talks on the issues facing mining today are scheduled for Tuesday and Wednesday mornings, but the real action will happen out on the floor. That?s where ultra haul trucks big enough to carry as much as 363 t (400 st) of rock will be assembled next to underground loaders able to lift more than 20 t (22 st) in one scoop. Caterpillar, Komatsu, Liebherr, Sandvik, Atlas Copco: all the big names in mining equipment will be there. Their massive earthmoving equipment and mining machines are the centerpiece of the show. Preassembly for the largest pieces begins on August 6, 2012.

Jan 1, 2013

By Rodney H. Sergent

After being forgotten or ignored for nearly 100 years, the ability of bromine chemistry to extract gold from ore has been rediscovered. While bromine chemistry is similar to chlorine, there are some important differences. Bromine in its elemental form is a dense, fuming, red liquid. Elemental chlorine is a gas and requires a substantial amount of equipment to handle, store and deliver to solution. Bromine has an advantage in its ability to rapidly and completely oxidize heavy metals to water soluble halide salts. The first patent for use of bromine chemistry for gold extraction was issued in 1881 (1). By 1895, work done in Colorado concluded well roasted ores required approximately 1-1/2 lbs/ton of elemental bromine for superior extraction of metals (2)). At that time, bromine was deemed to be cost effective vs. chlorine even though it was more expensive on a pound basis than chlorine. The advent of cyanide technology virtually eliminated both chlorine and bromine from consideration for leaching of ores. Cyanide was so inexpensive that it made deposits requiring unique technologies unattractive for mining. Only since the deregulation of gold price has bromine/chlorine technology been considered for those ores not amenable to cyanide. While chlorine has found its way into the pretreatment steps, bromine is just beginning to realize its niche in the marketplace.

Jan 1, 1998

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By H. Wilcox, M. Prichard, Y. P. Chugh

Environmental considerations related to the disposal of coal combustion byproducts (CCBs) and the impacts of deforestation associated with the harvesting of timber for utilization as roof supports in mines should become more severe in the future, as landfill space and suitable timber reserves become more scarce. To help address these concerns, lightweight artificial supports, such as post and crib elements, that use large percentages of coal combustion byproducts as aggregate have been developed for use in underground mines. These structural products show equal or better engineering characteristics than timber, and they have the potential to replace timber support in underground mines. CCB-based ultralight structural material (ULSM) has also been developed and commercialized for use in the construction of ventilation stoppings in underground mines. The bulk densities of these blocks range from 0.40 to 0.64 g/cm3 (25 to 40 lb per cu ft) with more than 75% CCBs. Efforts are also given to develop and demonstrate large volume CCB-based subgrade improvement technique for road construction. Soil treated with SIUC fluidized-bed combustion (FBC) fly ash developed an immediate bearing value exceeding 25% with a swelling strain of less than I %, which is greater than untreated soils, and met Illinois Department of Transportation (IDOT) standard specifications. In this paper, development procedures, engineering characteristics and beneficial uses of CCB-based structural products are given.

Jan 1, 2002

By G. M. Wilemon, B. J. Scheiner

The Bureau of Mines conducted investigations on extracting phosphate values from fine-particle wastes generated during the mining and beneficiation of phosphate ore by leaching dried wastes using a H2SO4-methanol mixture. Although phosphatic clay waste contains up to a third of the phosphate originally present in the ore, recovery of these values represents a significant challenge due to the fine grain size of the material, the particles averaging less than one micrometer in diameter. Waste samples obtained from two Florida producers yielded phosphate extractions of 71 and 84 pct, respectively, when leached under ambient conditions and at a stoichiometric acid ratio of 1.4:l. Elevated temperatures did not improve the amount of phosphate extracted. Undesirable A12O3, Fe2O3, and PlgO impurities were largely rejected; higher grade wastes gave acids that meet established industry impurity standards and lower grade samples yielded acids that marginally fell short of the standard. Separation of the crude acids from the insoluble residues was accomplished via vacuum filtration through either filter paper or commercial filter cloths. Both filtration rates and solids retention were improved by the addition of 0.5 lb/ton of poly(viny1 acetate) (PVAc) or poly(ethy1ene oxide) (PEO) to the methanol-acid slurries. These results show potential for substantially increasing the reserves of an important domestic resource.

Jan 1, 1989

By U. Srivastava

In the processing of manganiferous ore, it is useful to control whether the manganese (Mn) goes to the iron product to produce ferromanganese, or to the slag for extraction as a high Mn product. This can be done by manipulating the thermodynamic conditions for manganese oxide(MnO) reduction to control whether it remains as MnO or converts to metallic Mn. Results are presented showing that during production of iron nuggets, reduction of manganese oxide (MnO) can be controlled by changing the furnace temperature and reductant composition appropriately.

Jan 1, 2010

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By Ehsan Alavi, Brian Hagan, Colin LaVassar, Glen Frank, Derek Dugan, Rick Capka, Lisa Mori

"Tunnel face instability is one of the most common issues in EPB tunneling. The evaluation of an ideal face support pressure is a critical element in the design and construction phases of EPB tunneling. In this study, measured tunnel face pressures in three EPB tunneling projects (University Link U230 and U220 projects and the Northgate Link Extension N125 Project) for Sound Transit in Seattle, WA are compared with the calculated analytical methods. This comparison shows that the analytical methods generally overestimate the required tunnel face support. The best practice for managing the face pressure in EPB tunneling operation is discussed based on the experience gained through these projects. Furthermore, the algorithm that is developed for identifying ground loss in these projects is addressed. INTRODUCTION Earth pressure balanced tunneling relies on using muck within the chamber to support the face. Muck is pressurized by controlling the advance rate of the tunnel boring machine and the speed of the screw conveyor. Target face pressure is typically calculated by using the geotechnical assumptions in the geotechnical baseline report. The concept behind EPB tunneling is that the application of sufficient face support pressure will prevent tunnel face instability and the resultant over excavation. Tunnel face instabilities caused by a lack of sufficient face support can lead to ground loss and surface settlement (Anagnostou & Kovári 1996, Kirsch 2010). A certain support pressure must be achieved to counteract water and earth pressure with an adequate factor of safety. While the water pressure can be predicted accurately, the determination of the resultant earth pressure on the face is less precise. This becomes manifested in the relatively high partial safety factors on the earth pressure."

Jan 1, 2016

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and utilize a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow con- trolling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1987

By Renfeng Song, Shaoyan Wang, Zhiqiang Zhang, Ke Guo

Leaching titaniferous magnetite concentrate with alkali solution of high concentration under high temperature and high pressure was utilized to improve the grade of iron in iron concentrate and the grade of TiO2 in titanium tailings. The titaniferous magnetite concentrate in use contained 12.67% TiO2 and 54.01% Fe. The thermodynamics of the possible reactions and the kinetics of leaching process were analyzed. It was found that decomposing FeTiO3 with NaOH aqueous solution could be carried out spontaneously and the reaction rate was mainly controlled by internal diffusion. The effects of water usage, alkali concentration, reaction time, and temperature on the leaching procedure were inspected, and the products were characterized by X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. After NaOH leaching and magnetic separation, the concentrate, with Fe purity of 65.98% and Fe recovery of 82.46%, and the tailings, with TiO2 purity of 32.09% and TiO2 recovery of 80.79%, were obtained, respectively.

Jun 16, 2021

By S. I. Angadi, C. Eswaraiah, Sunil Kumar Tripathy, T. Santosh, Nilima Dash

Banded hematite quartzite (BHQ) and banded hematite jasper (BHJ) ores represent a promising potential iron ore resource in the near future. The hematite and quartz in BHQ and the hematite and jasper in BHJ are closely related and require fine grinding for the liberation of hematite phases. The present study investigates the mineralogical features and comminution properties of BHQ and BHJ ores. In the BHQ ore, it is observed that thick bands of hematite have fine inclusions of silicate minerals, whereas silica bands have few grains of iron-bearing minerals. The hematite and quartz minerals in the iron and silicate bands of the BHJ ore appear to be more intricately associated and complex in nature, presenting difficulties for liberation. Bond work index studies were carried out for the BHQ and BHJ ores with different product fineness in order to evaluate the energy requirements in fine grinding. A higher Bond work index value was found for the BHJ ore (15.4 kWh/ton) than for the BHQ ore (12.4 kWh/ton). A decrease in the product particle size was associated with an increase in the work index value. Single-particle breakage experiments were designed by varying feed particle size and input energy. The specific energy consumption for the BHJ ore was higher than that for the BHQ ore. The comminution parameters showed that the BHJ ore is harder to grind than the BHQ ore, which may be due to the mineral composition and association of hematite phases with the silicates.

By G. A. Shirey

Breakthroughs in software technology and in computer hardware capabilities have opened new opportunities to develop more accurate process simulators and to reduce the operating time to reasonable levels. As a result, there are several new simulation packages being commercialized for modeling coal preparation plants and pulverized coal-fired power plants, and the users of these packages are reporting significant improvements in process efficiency and operating costs by implementing the simulators&apos; results. This paper provides an overview of some of the models currently in use at CQ Inc., including the ASPEN PLUS"" Coal Cleaning Simulator, the Ultramax® process optimization software package, and EPRI&apos;s Coal Quality Impact Model?. Case histories of specific applications are also presented.

Jan 1, 1995

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By Ewan Alexander

"As human beings, we have managed risk since the dawn of the ages and have been adept at doing so. In order to survive, we hunted or gathered. If we did not take enough risk, we died. If we took much risk, we died (Fig. 1). As individuals and tribes, risk had to be optimized to maximize our chances to thrive, as individuals and as tribes.In today’s world, the risks are vastly different, but in order to thrive, these must be managed. And no industry knows this as much as mining. In fact, the International Council of Mining & Metals (ICMM) has proposed the Critical Risk Model (Fig. 2) as a means of identifying critical risk, critical controls and associated performance standards. The ICMM focuses on sustainable development performance in the mining and metals industry. It has 23 members, representing some of the largest mining companies in the world.This approach is going to help the mining industry. But it must be applied effectively, with the acknowledgment that the system alone cannot be effective. We can say this confidently, as even companies known for the strength of their risk and safety management systems continue to experience significant incidents, and, in some cases, catastrophes. Why does that happen when all safety metrics, including injury rate, are pointing in the right direction? In the view of the author, it is only when leadership, culture and systems work in complete harmony that the resilience of an organization to manage its significant risk is at an optimal level. It remains an ongoing leadership challenge to maintain that balance and the optimal mindset in the organization. So how do you maintain that special balance?Let’s start with a basic premise. Leadership, supported by simple effective systems, creates culture which creates outcomes. Everyone going home safely is an outcome, as is cost effective operations, and to achieve those outcomes efficiently, the organization must focus on the inputs. And those inputs include effective leadership, effective systems (for the purposes of this article, risk and health, safety and environment (HSE) systems), good planning, stable operations and competent workers. This article will focus on gaining maximum performance from your risk management system."

Oct 1, 2016