Search Documents

By William S. Hallager

Banded ironstone and associated fine-grained carbonaceous sediments near Jardine, Montana, are enriched in gold, arsenic, and tungsten. The mineralized sediments lie within a thick sequence of quartz-mica schists cut by a 2.6 b.y, granite. Surface, underground, and drill hole mapping are used to construct structure contour maps of individual ironstone lenses. Each lens is then unfolded by triangulation of minimum surface path distances between drill hole penetration points. Major and minor element abundances in composite ironstone samples are interrelated through R-mode factor analysis. Results indicate five significant element groupings thought to reflect coarse detrital, fine detrital, sulfide-rich chemical, iron-rich chemical, and epiclastic ultramafic sediment. Ultramafic factor scores are highest in a previously undefined rock type rich in cummingtonite, biotite, and chlorite; lacking in quartz; and closely associated with at least one ore horizon. Detrital dilution of ironstone, calculated from chromium and nickel content, drops off significantly as ore-bearing ironstone is approached. This observation may indicate that centers of gold precipitation have protected themselves, either topographically or by rapid deposition, from detrital contamination. Gold mineralization correlates most strongly with the sulfide- rich factor. Gold may have been introduced through hotspring activity as a bisulfide complex.

Jan 1, 2013

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By Thornton L. Neathery

The low-grade talc deposits in Tallapoosa County, Alabama, are associated with a mafic-ultramafic rock complex that is part of a widely distributed schist and gneiss group. These rocks form a synform structure overlying Inner Piedmont lithology. Paragenetic sequence of the Tallapoosa talc is interpreted as enstatite-anthophyllitetalc. Talc occurs as massive boulders formed by the alteration of enstatite-anthophyllite and as finely disseminated discrete particles in the enclosing saprolite matrix. Weathered rock reaches depths as great as 60 feet. The quality and quantity of the talc, however, are variable. Mineral analyses of the talc-bearing samples, by petrographic grain count, indicate a talc content of 16 to 26 percent. Most of the talc occurs as plates or scales that are moderately stained with limonite. Fibrous talc also occurs in the deposits and is often mistaken for anthophyllite asbestos which is intimately associated with the talc. The size, shape, and occurrence of the talc deposits precludes any method of min¬ing other than open-cut. A small-scale mining operation began in the district in 1969. Potential capacity of the operation is 5, 000 tons per year. Inferred reserves, based on field investigations, are placed at approximately 8 million tons. Approved for publication by the State Geologist, Geological Survey of Alabama.

Jan 1, 1970

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step-function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step-function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another is-sue is how they compare to peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1997

By Z. H. Xie, D. S. He, W. M. Xie

China has rich phosphate rock resources, but with their continuous depletion, the rich ore resources have become increasingly scarce, which makes the exploration of collophane more important. Medium- and low-grade phosphate rock cannot be utilized until their impurities have been removed through mineral processing. However, due to the similar physical and chemical properties of dolomite and phosphorus minerals, the separation of dolomite from phosphate

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By Nagashi Ogushi

Geochemical prospecting method using stream sediments, soils and rock chips has been tested to see the applicability for the typical Kuroko field in Japan. Three independent anomalies have been detected in maps being shown by grav densities of cells which are represented by the results of factor analysis as well as distribution of minor elements scaled in logarithm. A small vein type mineralization which has outcrops could be attributed to the origin of them whereas the one near the surface of known Kuroko deposit to a coincidence. The addition of drill core geochemistry is required to complete the interpretation.

Jan 1, 1982

By R. Mulyanto, M. Siray, A. Parhusip, F. Hartono

"PT Freeport Indonesia is preparing the Deep Mill Level Zone (DMLZ) mine to be the successor of the currently operating Deep Ore Zone (DOZ) mine. The DMLZ is block cave mine situated 500 m below the DOZ mine and approximately 1600 m depth from surface. Both of the block caving mines require draw point construction in the extraction level to extract the ore from caved area above. Learning from the experience in DOZ, the construction & maintenance of draw points in the production panels is a significant challenge in supporting consistent production.The average DOZ draw point construction duration is approximately 46 shifts per draw point. The time frame for construction is dependent on several variables; availability of the conventional forming system, material availability, and development tolerances. The repair of concrete floors and lintel sets causes production downtime. Reviewing the old DOZ draw point design, there is an opportunity to increase constructability, durability, and reliability of DMLZ draw points. This paper discusses how the DMLZ has improved draw point construction productivity and is on track to significantly reduce costs whilst increasing the quality by using the Six Sigma Improvement Method.Introduction The DMLZ Mine is part of the PT. Freeport Indonesia (PTFI) future Expansion to its underground mining complexes. It is the fourth vertical lift in the East Ertsberg Skarn System (EESS) deposit (Figure 1).Currently, it is under development phase.The DMLZ mine will be a block cave mine using an advanced undercutting method. The DMLZ extraction level will be approximately 1,600 meters below the surface on the 2570 level with column heights of roughly 500 m. The Undercut is on 2590 level, some 20 meters above the extraction level."

Jan 1, 2016

By M. P. Smith, C. Hughes-Narborough, Y. T. Man

"Money and reputations can be lost in bad projects. Causes of bad mineral processing projects include poor contract definition and purchase of equipment without adequate test work. However, the root cause of many of the problems that can lead to bad projects is not any inanimate object, bad weather or catastrophic natural event but the people working on the projects. Because the people are so critical to the success of a mineral processing project, one must have suitably qualified and experienced people (SQEP) in all key positions. Characteristics that define SQEP include people who have successfully executed projects of similar size before; have undertaken projects treating the same minerals and producing the same valuable products and people who are familiar with designing, operating and implementing the required technologies and unit operations.To minimize the likelihood of future bad mineral processing projects, five recommendations are put forward in relation to the people aspect of a project.1. Attempt to retain SQEP during any down turn in the mining economic cycle so thatthe knowledge and experience can be kept within the industry.2. Increase the effort in attracting young people into the industry and retaining them.3. Set up robust training program to give young professionals a firm foundation of what real life projects and operations are like.4. Provide mentoring and continuous training for people after they have completed their formal graduate training program. Their career progression should be appropriately monitored and controlled.5. People working in projects must be exposed to as many detailed design and other finer issues as possible so that they can comprehend the amount of work required to deliver a project successfully."

Aug 1, 2016

By Camilo Quintero, Frank Cesario, John Kinnear, Brian Boye

In this paper, an innovative approach was adopted to automatically calculate the effects of tunnel induced settlement on buildings and utilities. The approach resulted in increased output quality, consistency, reduced time, cost savings and a greater ability to respond quickly to design changes. The techniques described have been applied to the Fairbank Silverthorn Storm Trunk Sewer System project, located within the City of Toronto. The automation allowed a very large area of topography, tunnels (6 km), buildings (9000) and utilities (over 1000) to be rapidly evaluated. Visualization of the settlements and impacts also allowed the project design team to optimize the system design to mitigate the settlement impacts.

Jun 13, 2021

By Nikhil Dhawan, Amit Barnwal

The present study reports a processing route to recover metals from integrated circuits of discarded random access memory (RAM) units containing ~ 66% printed circuit boards and ~ 33% integrated circuits. The integrated circuits are manually separated, grounded, classified, and subjected to water fluidization for the effective separation of metals. The significant separation was achieved via water fluidization, and the underflow fraction was magnetically separated. The magnetic fraction was thermally exposed in a muffle furnace, and the process optimization was carried out using a Box-Behnken statistical design. The detailed characterization at subsequent steps significantly aids the understanding of metal-plastic separation and enrichment. A concentrate containing 97% metals (Fe-59%, Ni-9.5%, Cu-7.7%, Sn-13.4%, Pb-5.6%, Ag-1.6%) with 96 wt% recovery can be recovered from discarded IC units. The process pursued is simple, adaptable, and environment-friendly, and the product can be used in conventional smelters.

Jun 23, 2020

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

As a result of the rise in global demand for pure copper, there is urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as an effective and efficient leachant for the dissolution of chalcopyrite. This work reports different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from Wase Local Government Area, Plateau State, Nigeria, and assayed as 11.30 wt% of Cu. At the optimum leaching conditions (0.4 mol/L NH3-( NH4)2SO4 leachant concentration; 75 °C reaction temperature; 45 μm particle size), the extent of chalcopyrite ore dissolution reached 87.4% within 120 min. The dissolution rate was affirmed to conform to the diffusion control mechanism with the activation energy, Ea, of 38.84 kJ/mol and a reaction order of 0.661 for the leachant concentration being established. The leaching mechanism was affirmed by characterizing the raw ore and the leached product by XRD and SEM-EDS analysis. Ascertaining optimal leaching conditions for copper using alkaline leachant is advantageous from the environment and economic points of view.

Jan 6, 2023

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The early mining of iron ore in Minnesota was carried on with the most primitive kind of tools. The pioneers used only such equipment as could be packed from Duluth through one hundred miles of forest to the first mines on the Vermilion Range and the operations were carried on with picks, shovels, hand drills and wheelbarrows, the ore being hoisted in buckets with a horse winch and carted in horse drawn wagons to the stockpile. This was about the extent of the mechanical equipment of the Minnesota iron mines in the early eighties.As soon as a railroad was pushed through from Two Harbors to the Vermilion Range the equipment began to be improved upon; wood burning steam boilers were installed and small steam puffers displaced the horse-winches, wheelbarrows were aban¬doned and small cars were introduced. Hauling the hoisted ore in wagons was discontinued and trestles were built so that the ore could be stockpiled more cheaply through the use of cars and high piles. These same stockpiles were loaded by hand into the 10 and 15 ton capacity railroad ore cars.Within a few years a marked change took place—the hand drill gave place to the air drill, such as No. 3 Rands, Ingersolls, Sargents and some Sullivans. Tramming was done by mules, the ore hoisted in. self-dumping skips, hoisting engines were intro¬duced and it seemed as though mining as a business in Minnesota had come to stay. At this stage someone conceived the idea of making the stockpile floor about three feet above the top of the ore cars to facilitate the hand loading of stockpile ore for trans¬portation. This was done through the use of wheelbarrows at first and later by using I-ton cars running on tracks laid on the stockpile floor."

Jan 1, 1920

By J. H. Gwynne

[ ]

Jan 1, 1962

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998

By Jiachen Wang, Nan Wang, Yang Li

The energy structure and consumption ratio in China determine the practical demand for the collaborative mining of coal and co-associated resources. The multi-layer mining of coal, uranium, coalbed methane, and oil and gas co-associated resources, represented by the Ordos Basin, Junggar Basin, and Tarim Basin, faces numerous challenges. Additionally, coal has been found to coexist with various mineral resources in 33 coal-bearing basins worldwide. The scientific issues related to the multi-layer development of coal related co-associated resources urgently need to be addressed. This paper discusses the unique challenges and potential solutions in the multi-layer development of coal-related co-associated resources. The challenges include large extraction space, high mining intensity, intense overburden movement, rapid surface subsidence, and severe overburden damage due to repeated mining disturbances. Proposed solutions include the establishment of a correlation mechanism between multi-layer mining and the carrying capacity of the overburden environment, analysis of the impact characteristics of multiple field couplings, and exploration of their superposition evolution laws. The paper also proposes the development of a comprehensive evaluation and prediction system for overburden environmental capacity loss, a global sensitivity analysis model for overburden environmental capacity, and an intelligent identification and early warning system based on multi-source information fusion. These solutions aim to achieve scientific and precise mining with minimal overburden environmental capacity loss. And the multi-layer development of coal-related co-associated resources is a complex task that requires a multidisciplinary approach and innovative solutions, and further research is needed to validate these strategies and explore new methods and technologies for efficient and sustainable extraction.

Jun 25, 2024

By C. Roos

Traditionally within the mining industry, the main functional process flow for resource and reserve evaluation proceeds from geologists who build the geological model, to resource estimation geologists (modelers) who estimate the grades, to mining engineers who develop the mine design and schedule. The interface between these three disciplines is not always seamless. Assumptions made during one stage of the process are not always communicated down the line, even though most mining companies have procedures in place to encourage communication across the various disciplines. These procedures do not always achieve their aim due to a variety of reasons including time constraints, appropriate people not being available, or a lack of understanding of what other disciplines require, and the handover process can degenerate into one of sending computer files on to the next discipline in the process flow. This paper focuses on the interface between the resource estimation and mine engineering disciplines, and outlines some of the common assumptions made when generating a resource model and the risks that engineers may be taking when elevating cutoff grades, optimizing schedules or generating forecasts. The case studies presented focus on openpit gold deposits, but the concepts should be applicable throughout the industry. A summary of key questions and recommendations is provided.

Jan 1, 2014

By M. A. Qianjie

The problems of coalmine safety in china remain unsolved for decades. Starting with the description on safety status quo of coalmine in china, different existing analysis and measures discussed for the safety problem solution of coalmine china. With the consideration of system thought in mind, the author present with a unique systematic reason analysis method on such actuality--individual analysis and general analysis--each for its particular purpose. Upon such cause analysis, construction of the safety system is made clear and, solutions for such problems provided.

Jan 1, 2006

By A. Griffiths

The? use of hydrogen peroxide to detoxify gold mill waste waters containing cyanide and other toxic substances is already an established technology. Recent advances have extended the range of application of hydrogen peroxide treatment to include the removal of complex iron cyanides, the simultaneous removal of cyanide and toxic metals down to very low levels and treatment of barren bleeds, CIP' pulps and tailings pond discharges. Three treatment plants are described here. Each was installed at a gold mine in North America in 1987 and each illustrates a different application of hydrogen peroxide. The need for individual design of the detoxification plant to fit particular requirements is shown by the examples chosen.

Jan 1, 1988

By L. M. English

A basic model has been developed to help assess methane control needs for longwall mining of coal in gassy areas. Rather than depending upon reservoir and rock mechanic theory, it uses an empirically-determined gas emission rate as an input and operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance, and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid the determination of the number, size, and location of vertical wells or other methane control applications that are needed for gob gas control.

Jan 1, 1998