Search Documents

By Babcock. C. O.

This report presents equations derived from experimental testing to convert borehole pressure cell data from vertical and horizontal cells to the biaxial ground stress changes. While hydraulic pressure cells in boreholes have been in extensive use since 1957, methods of data reduction have been slow to develop. The methods of Sellers (1970) and Bauer et al. (1985), respectively, indicate a linear relationship between cell pressure change and the rock stress change. Lu presented a theory for creep behavior (Babcock et al., 1982). In the present work, in laboratory testing, the logarithm of the cell pressure was related to the stress change in seven elastic materials for a range of Young's moduli of 3.45 to 85.5 GPa (0.5 to 12.4 x 106 psi). The gage response depends upon the setting pressure of the gage, the gage pressure at any time, the rock properties, and the cross-sensitivity of the gage to transverse loading. The setting pressure of the cell should be proportional to the Young's modulus of the rock, the absolute stress can be determined by overcoring in strong rock, and the in situ Poisson's ratio can be estimated in some cases from the cell responses.

Jan 1, 1986

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1993

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1991

By Jesse H. Auvil

In January of 1966, during the annual session of Georgia's General Assembly, Representative Paul E. Nessmith of Statesboro, Georgia, walked into my office and asked me what I thought of the advisability and feasibility of a law which would require the mining operators to reclaim their mined out lands. My answer to him was, as a one time mine superintendent and operator, that I probably would not think very highly of the added cost which reclamation would impose on the operation; but that since assuming the job of Chief Geologist and Assistant Director of the Georgia Department of Mines, Mining and Geology, and in retrospect, I could recommend it very highly, particularly in view of the increased pressure being applied by the Federal government along these lines. I stated then and still emphatically state that this sort of administration should be done on the State level rather than the Federal level. He asked me if I would conduct him on a tour through some of the mining country in which I had worked and to this I readily agreed. The result of this trip was that he was adversely impressed by the devastation which the mining operations had wreaked on that area of middle Georgia along the fall line known as the kaolin belt. Very little except talk was done for the remainder of 1966.

Jan 1, 1970

By Frank J. Skudrzyk, Vladimir F. Petrov

In compliance with the current Russian environmental legis­lation, possible impact of industrial activities on the environment is restricted by acceptable limiting values (maximal allowable concentrations - MAC) of individual chemical substances in the natural environment - water, atmospheric air and soils. These norms have federal status and are valid for the whole territory of Russia. Disposal of the substances, for which no MAC is estab­lished, is forbidden by the law. Many gold mining companies use cyanide in precious metal recovery. This paper overviews the Russian experience in pro­tection of natural water reservoirs from technogenic impact of cyanic technologies. Major toxic compounds, contained in liquid and solid rejects from hydrometallurgical treatment of gold ore using cyanidation, are cyanides (CN), thiocyanates (SCN) and cyanide metal com­plexes. Unlike western classification of various cyanide types, in Russia any inorganic cyanide compounds (simple and in com­plexes with metals), with the exception of iron cyanide com­plexes, are considered toxic and the acceptable limiting value is established for them. MAC is 0.05 mg/I for fish reservoirs and 0.1 mg/I for drinking water. For iron cyanide complexes MAC is 0.15 mg/I for fish reservoirs and 0.25 mg/I for drinking water. Russian norms for thiocyanates are practically as rigid - the acceptable limiting value for them in fish reservoirs is at the level of 0.07mg/l (0.15 mg/I for potassium thiocyanate) and for drinking water - O. lmg/1. Norms for metals are established on the basis of total content regardless of the form in which they are present in water - as cations or complex ions. It should be noted, that in case several toxic compounds of the same limiting value (for cyanides, thiocyanates and base metals the limiting value is toxicological) are present in water. Their allowable concentra­tion is calculated as the sum of actual concentration of each com­pound, divided by the corresponding acceptable limiting value, with the result not to exceed one (compounding effect). Differences in cyanide classification and the necessity to include thiocyanates dictate different analytical methods. This, in a number of cases, results in certain discrepancies in analytical results. Until recently chlorination was used as a basic process of detox­ification of wastewaters. Calcium hypochlorite powder or hypochlorite pulp, prepared of lime milk and chlorine shipped to the plant, were used as a reagent. Chlorination is an efficient method: it allows to completely destroy plain and complex cyanide, in addition to iron complexes, and thiocyanates. A good example of high efficiency chlorination can be found at the Mnogovershinniy mill near the Okhotsk Sea located in the salmon spawning area, for which we designed an automated chlorination plant for tailings dam. Since plant start-up ten years ago, the required concentrations of cyanides and thiocyanates have been kept at the MAC level required by environmental regulatory agen­cies and no harmful affects on ichthyofauna has been reported. One major drawback of chlorination is high cost of the major reagent, as well as secondary contamination of detoxified waters by chlorides. Secondary contamination by chlorides becomes obvious in the course of detoxification of wastewaters of com­plex composition, which require increased reagent consumption. Recent changes in economic conditions in Russia caused the necessity to direct efforts to reduce the costs of precious metals recovery, and in particular, wastewater treatment. We have con­ducted certain work in this direction and obtained positive results. We hope that our experience described below will be of interest to other specialists particularly taking into account the current low gold prices.

Jan 1, 1998

By M. Javier

"Mining makes civilization possible. It also creates socio-environmental liabilities forcing us to ask how much more of this mining can our planet support. It is clear that the future of mining differs from mining in the future. The laws of nature are being compromised by mining. This paper studies the problems at the core of the mining business which need to be addressed. What kind of mining will serve our existence with nature on this planet? What kind of mining perspectives are we able to formulate without having negative effects for future generations? Is mining technologically sustainable? The values of predictions, imagination, and creativity must be integrated to define what mining should be. Those values should be in the technologies necessary to restoring equilibrium of nature (Geomimic) as well as in complete extraction of metals, better utilization of the mineral reserves, and design the usage of metals to recycle. The purpose of this research is to examine many views and perspectives for future generations and to accelerate the pace of innovation of having mining without socio-environmental liabilities by design and by understanding nature. KEYWORDS: Geomimic, Sustainability, Waste mine Design, Management by Loss. INTRODUCTION The future of mining is being stifled by many antiquated and stagnant attitudes and policies by the industry and society as a whole. The time is now or never for real action and education against these attitudes and to upgrade them to meet the current needs of this planet if we are to survive. Doing this will prove that we understand and respect nature for us and our posterity. It will also show a positive assessment that the mining process can be reversed before the point of no return. And that is to say, only if reversibility is still an option. It may not be anymore but it’s worth a try. We need to use our imagination and engineering know-how to come up with new proposals to change the core of mining. It would entail re-engineering. There is a profound difference between the future of mining and mining in the future. The future of mining is the continuation and persistence of past practices in the industry and expecting new results. Mining in the future requires a paradigm shift for extraction through modern thinking about mining as it pertains nature. The new paradigm for mining in the future would restore equilibrium with nature. Always keep in mind the connection of mining to nature. What is the future of nature? To predict mining in the future we need to use past experiences in mining and our knowledge of modern science and engineering to formulate a prototype that will enhance mining while maintaining equilibrium with nature. Mining and protecting nature are not mutually exclusive. This new prototype has nothing to do with the level of bonding or insurance that the mining industry can legally provide. The goal of this paper is to contribute some new ideas to help transform the mining industry based on the laws of nature and its limitations. Using this new prototype we will develop the following 1. Extraction of minerals Reserves-Dimensions-Technologies 2. Usage of mineral resources-Manufacture’s products designed to be reused and recycled 3. Nature- Equilibrium (physical, chemical and biological)"

Jan 1, 2016

By M. Gomilanovic

The Republic of Monte Negro (a member of the Serbia and Monte Negro federation) has 26 different mineral raw materials, 4 of which are recoverable and 22 unrecoverable. At present, 12 types of mineral raw materials are exploited. Based on these resources more than 80 facilities were built for the production and processing of mineral raw materials. The most significant of them are coal, bauxite and decorative and technical stone. Bearing in mind that all the mentioned mining facilities have significant impact on the living environment, and that Monte Negro was declared the ecological state, the objective of this paper is to present the experience acquired from this field of science.

Jan 1, 2003

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By O. R. Bell

In Australia&apos;s remote North West are located the operations of Cliffs Robe River, one of the world&apos;s largest iron ore projects. Initial project cost was $US300 million and required the construction of a deepwater port, two toms for 3000 people, a 105 Mw power station and 170 km of railroad, all in harsh, arid country over 1300 km from the nearest industrial centre. The ore occurs as goethite cappings on scattered mesas and averages 57 percent iron. All aspects of the project are reviewed from pre-operational research, through project construction to current operation.

Jan 1, 1979

By Khosrow Badiozamani

Depletion of easily accessible coal reserves and stringent competition in coal marketing has led to the coal industries&apos; need to more accurately assess alternate development scenarios and to develop well-conceived produc¬tion plans. This, in turn, has encouraged the active use of the computer during resource eval¬uation and mine planning. Morrison-Knudsen, (M-K) has developed proprietary software, known as "EAGLES", to support not only its own mine planning and development activities but also the mining industry in general. The EAGLES system provides complete geologic modeling, mine planning, production modeling, equipment modeling, and cost and financial modeling capabilities. In addition, EAGLES can be used for geotechnical studies, environmental assessments, and surface and groundwater hydrological evaluations. Another important tool used in today&apos;s mine development is Landsat (remote sensing). Landsat is especially useful in the evaluation of mining activities at remote mine locations and for megascale assessments of geologic structures and hydrologic regions. The use of scientific systems in the development of surface mines is being well integrated into today&apos;s mining operations and will be a major factor in the planning, development, and operation of mines in the future.

Jan 1, 1985

By Francis Martino

Just as coal producing mines are faced with various handicaps which control the quantity of coal produced and sold, the subsequent user of that product is faced with parameters that impact the optimum utilization of coal. Traditionally, the industry focused on the quantity of mineable coal in a reserve. The mine planning development was primarily concerned with two important criteria: (1) safety and (2) the productive efficiency in a quest to produce the lowest cost coal.

Jan 1, 1982

By Ava Segal, Doga Cagdas Demirkan, Abhidipta Mallik, Sebnem Duzgun, Andrew J. Petruska

Search and rescue operations in mining heavily rely on humans. In the context of emergency situations within underground tunnels, the potential to utilize sensory technology for navigation assistance holds the promise of saving human lives. Our research introduces a device configuration designed to enhance the performance of search and rescue teams. This setup integrates LIDAR and thermal cameras with the Microsoft Hololens, facilitated by the NUC computer and ROS Bridge. Performance assessment involves quantifying the extent to which a user is willing to venture into a light-deprived section of the mine prior to necessitating supplementary illumination. The preliminary outcomes highlight the significant potential of augmented reality assistance in offering indispensable aid to first responders, thereby greatly augmenting the efficiency of search and rescue missions conducted during critical circumstances.

Feb 1, 2024

By M. Morrongiello

The Kalgoorlie Consolidated Gold Mines Fimiston Open Pit is mining through a dense network of disused level workings and stopes of varied sizes and orientations. This study investigated the interaction between underground workings and the pit slope stability, in particular for the ultimate pit depth of over 600 metres. Parametric analyses were conducted on the structural and rock mass properties in order to provide realistic input. Several cases in both 2D and pseudo 3D using UDEC were modeled and analyzed to investigate the performance of the rock mass at various mining stages. The concept of equivalent property factor was also introduced to model the 3D behavior using 2D models. Based on the modelling results, the possible failure mechanisms and deformation of the pit walls were assessed. Factors of safety have been derived for the pit slope at different mining stages using the strength reduction technique. The modelling results agree well with pit performance monitoring results to date. The concept and results presented in this paper could be a useful reference for operations with similar circumstances and stress regimes.

Jan 1, 2005

By J. Luo

A major design problem for upper seam longwall gate roads that are to be constructed in a multi-seam environment is to predict the effects of stress field changes created by interaction. To quantify these effects, case study data were analyzed to develop empirical stress transfer relationships between seams for both longwall and room and pillar mining. Data analysis showed vertical movement and roof characterization in the upper seam to be controlling factors in damage prediction and, therefore, gate road planning and design. CMRR (Coal Mine Roof Rating) was correlated with the multi-seam roof characterization systems previously used. A WINDOWS-based software package named UGLY (Upperseam Gateroad Longwall Stability) was developed. Results from selected case studies were correlated with upper seam stress predictions.

Jan 1, 1997

By Miguel Reyes, Mathew Girman, Chenming Zhou

Modern smart mining increasingly depends on sophisticated electrical and electronic systems for improved safety and productivity. With more electronic systems being introduced underground, the mining industry faces electromagnetic compatibility (EMC) issues caused by electromagnetic energy emitted by one device adversely impacting the normal function of another. This paper provides an overview of EMC and electromagnetic interference (EMI) research for underground mining, including a review of EMI in other industries applicable to mining, published EMI research pertaining to mining applications, representative EMI incidences, related EMI legislation in mining, and mitigation strategies.

Jan 3, 2022

By C. Sampaio, C. Petter, M. Veras

"INTRODUCTION Use of sensor technology applied to the gravimetric beneficiation is intended for the selective preconcentration or separation of various minerals. Sensor Based Sorting (SBS) uses sensors to identify the particles and separate them by a mechanical process (flap) or pneumatic ejection valves (Wotruba et al. 2014). The principle of the SBS technology to separate mineral particles consists of three phases which cover feed,detection and separation. (killmann, 2009 Apud nienhaus et al. 2014). The applicability of the technique in an early stage of beneficiation enables free particles and poor grade to be a part of the process. The mass of tailings to be processed can be removed at the initial stage to save energy, water and equipment maintenance (Wotruba et al. 2014). Lindner (2010) suggested that the use of SBS technology would only will be possible if there exsists an electromagnetic interaction in all the wave spectra interacting with the solid ore. The interaction of electromagnetic waves depends directly on the characteristics of the material. The material receives a spectrum of electromagnetic waves by irradiation and this results in a reduced wavelength with differing types radiation such as fluorescence, reflection, remission, absorption, transmission and transmission. The frequency of the wave spectrum varies between 1000 and 1020Hz, illustrated by the data in Figure 1, which shows that each type of sensor emits a wavelength inversely proportional to the frequency ranging from 10-11pm to 104km, and the frequency that varies between EHz 103 and 1020kHz. The difference between the electromagnetic spectrum variations can only be visible to the human eye at wavelengths with intervals between 380nm and 780nm (Wotruba et al. 2014). One of the main advantages of operating with imaging sensors is the versatility of the images which can take on zero, one, two or three dimensions shown below as a point, a line, an area or a spatial image, as illustrated in Figure 2. According to Schubert (1988), to separate a mineral particle it is necessary to follow the characteristics of mineralogy, physics and chemistry with or without use of water. The use of new technologies can help reduce operating costs and improve utilization of mineral resources."

Jan 1, 2016

By Charles A. Hickey

The dining industry game tome Spruce Pine area a few years after tine Civil War. Two Yankees came down from Massachusetts to mine sheet mica to sell to the stove manufacturers for windows in heating stoves. At this time the method of mining was very crude; it was done only with pick and shovel. They were mining mica from the soft veins. Later they progressed to hand grilling and blasting. Hand drilling was quite an art in the area. One man would hold and turn the steel while one or two other men would drive the steel with hammers. In shaft raining, the muck and water was removed by hand winches called windlasses. About 1920 air compressors and jack hammers came into use. These were perhaps tide greatest improvement that has ever come to the area&apos;s mining industry. Later carne gasoline hoists, air drive water pumps, and all electrical equipment. Mica mining has, for the past few years, been very modern and efficient.

Jan 1, 1962

By R. DasGupta

The dissolution behavior of gold in ammoniacal solutions at 75°C has been investigated. The variables investigated include concentration of lixiviants, pH of the solution and various oxidants. The anodic dissolution of gold was studied in the absence of oxidants using the potentiodynamic polarization technique. The cathodic reaction of oxidants was studied on a platinum electrode. Tafel polarization tests were also performed to determine the dissolution rate. The overall dissolution of gold in ammoniacal solutions was examined using a mixed potential theory. A comparative study on the role of cupric am mine, oxygen, hydrogen peroxide, sodium hypochlorite as oxidants for the dissolution of gold in ammoniacal solutions has been carried out.

Jan 1, 1996

By Jack E. Bailey

From a start in 1957, milling 3,000 TPD of copper ore, the Cyprus Pima Mining Company, which is located 20 miles south of Tucson, has expanded its operations four times, and is currently treating over 55,000 TPD of ore.1 The most recent expansion added a 14,000 TPD semi-autogenous concentrator to the operation. Shortly after startup in January, 1972, the semi -autogenous plant exceeded the designed tonnage rate.2 Ore from the mine is delivered to a 54 inch gyratory crusher and is reduced to a minus 8 inch product. From the crusher the ore is stacked on a surge pile and then reclaimed and fed to the two parallel grinding circuits. A 28 ft. diameter by 12 ft. long semi-autogenous mill and a 16.5 ft. diameter by 19 ft. long ball mill make up each grinding circuit. The semi-autogenous mills are in closed circuit with screens and the ball mill circuits are closed with hydro- cyclones. Rougher flotation follows the grinding operation. Concentrate regrinding and cleaner flotation is performed in Mill I, the older mill. The generalized flowsheet is shown in Figure 1.

Jan 1, 1975