Search Documents

By B. Barry, M. S. Klima

"Testing was conducted to evaluate the effects of hydroacoustic cavitation (HAC) treatment on two bituminous coal slurries and the subsequent separation of each slurry in a classifying hydrocyclone. HAC treatment was performed using a pilot-scale circuit fabricated by Furness-Newburge Inc. The circuit was designed to induce cavitation by means of flow through an ultrasonic resonator chamber or enhanced cavitation by initial flow through a cavitation chamber followed by flow through the ultrasonic chamber. The test materials were nominal -1,500-micron and -150-micron Illinois-basin bituminous coal slurries, which were obtained from an operating coal preparation facility. After 5 sec of HAC treatment, the median size of the -1,500-micron material was reduced, with ash values for certain size fractions decreasing more than 5 percent compared with untreated samples. Extending treatment time led to greater degradation of the +1,180-micron material and an increase in the -25-micron material, with ash reductions occurring for material in the -850+150-micron size range. Size degradation was less for the -150-micron material. Subsequent separation of the treated slurries was carried out in a hydrocyclone with diameter of 102 mm. HAC treatment led to a decrease in the ash value and an increase in the heating value of the underflow stream compared with the feed material. For example, the ash value was reduced by about 16 percent for the -1,500-micron material and 25 percent for the -150-micron material with heating value increases of 7 and 33 percent, respectively, after HAC treatment. Overall, HAC treatment appeared to have a slight effect on the size selectivity curves.IntroductionUltrasound in the range of 20 to 1,000 kHz, referred to as power ultrasound, consists of high energy waves that can create zones of compression and expansion when used to irradiate liquids (Frederick, 1965; Leighton, 1994; Mason and Lorimer, 1988). This action generates varying pressure regions leading to cavitation or the formation, growth and near-immediate collapse of microscopic voids or bubbles (Frederick 1965; Leighton 1994; Mason and Lorimer 1988). Collapse occurs when the bubble reaches critical size and cannot absorb additional sound field energy, and the critical size is governed by the ultrasound frequency (Shchukin et al., 2011)."

Jan 1, 2015

By Whitmell J. Smithwick

Lime is one of the most extensively used chemicals in industry. Other than sulfuric acid, it is used in greater quantities than any other man-made industrial chemical. In 1974 there were 20,368,000 tons of lime used in the United States, which amounts to approximately 190 pounds for each man, woman and child in our nation. Lime also is perhaps the most diversely used of any industrial chemical. It is used in such areas as pharmaceutical, chemical, steel making, glass making, production of copper and aluminum, sugar refining, agriculture, construction, ecological endeavors, potable water treatment and sanitation. Figure I lists the major uses of lime for 1974, which is the latest year for which this data is available. The impact of the use of lime for ecological reasons did not show up to any appreciable extent in 1974, but we expect this to be a significant factor within the next few years. Fortunately, in the United States and also in most of the world, there are many deposits of high quality limestone available for the production of hood quality lime. For this discussion, we will assure that a limestone of a suitable quality and size consist will be available in a storage bin or stockpile near the kiln. Quality requirements for the lime product will be covered. We also will give a brief description of the three most popular types of lime calcining systems, how they function, and expected lime product quality from each of these. Commercial fuels and major accessory equipment will be discussed briefly.

Jan 1, 1976

By B. N. Thompson

The main industrial minerals produced are non-metallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. The other minerals, some with minor production, include diatomite, feldspar, magnesite, sulphur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of Late Cenozoic acidic volcanic rocks.

Jan 1, 1982

By Frank E. Sullivan

The separation of liquids from granular materials has been widely studied by a number of: investigators over a period of years in an effort to more fully understand the physical phenomenon which occurs. Liquid may be removed from solids, or partially removed, by gravity separation, mechanical separation' or heat drying. Mechanical separation is advantageous when compared to heat drying principally from a cost saving standpoint and also on certain materials which are heat sensitive. It is realized however that mechanical separation of liquids has certain practical limitations. In order to evaluate the efficiency of mechanical separation and predict the extent of, liquid removal, it is first necessary to study the forces which hold the liquid to the solids. From a very practical observation using gravity drainage, it is soon obvious that a pile of coarse solids will drain faster and retain less liquid than a pile of finely divided solids of the same material. For commercial operations it is important to estimate the residual liquid which will remain after a mechanical separation. Batel (1) explored the various quantities of liquid present in the interstices of the bulk granular material. From his work and other authors which he has correlated in one of his recent papers, various formulas are now available which permit an empirical relationship to be developed showing residual moisture versus mechanical separating forces.

Jan 1, 1965

By R. W. Chadwick

Coal was discovered in South Africa in the mid 1830's. The earliest exploitation of modern times was probably in Natal where, in a letter dated 20 August 1842, a Captain Smith mentions that a wagonload of coal brought to Pietermaritzburg, was sold. Until the discovery of diamonds in 1867 and the Witwatersrand gold in 1886, coal mining satisfied a very small domestic demand. By 1889, at least four collieries were operating in the Middelburg-Witbank district, some 120 kilometres East of Johannesburg, and mining had star- ted at Vereeniging, about 50 kilometres to the South of Johannesburg. A map of South Africa is shown in Figure 1 and an enlargement of the main coal mining areas in Figure 2.

Jan 1, 1982

When I wrote the Railroad portion of "Mining Engineering" magazines 94 Powder River Basin (PRB) Coal Article I described to you some definite destinations the Railroads had in mind. As with many destinations, the ones I wrote of turned out to be merely stops on the way to places that we have yet to reach. Somewhere along the way we discovered that making it better is a continuous process not just something that you can do in phases I, II, III, & IV. We always knew this I suspect, but perhaps not at the awareness level that exists in RR environments in 1997. The purpose of this article is to update the 94 article, which I could do very quickly. Everything I told you we were going to do in 94 is done, end of story! But in addition to making it a very short article it would not be telling you the things RR has done beyond what we were planning in 94 and for the future.

Jan 1, 1998

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By William Gleason

With more than 20 major mines extracting copper, gold, coal, molybdenum and lime, Arizona is recognized as one of the better mining jurisdictions, not just in the United States, but in the world. However, that is not to say the road to production is always paved with gold, or in many cases, copper. Earning the license to mine in Arizona is a complex process with years of paperwork and permitting before the first tons of ore are ever processed. Now, get the federal government involved and the process becomes even more complex, and the path to production can become even longer.

Jan 1, 2013

By Morgan M. Sears

The LaModel program is widely used to calculate stresses and displacements on thin tabular deposits, particularly when multiple seams or complex mining geometry is encountered. The program itself allows the user to create multiple mining steps to show a progressive sequence of mining. However, LaModel considers each individual step as an independent steady-state condition, and any previous loading conditions of the materials are not tracked. It also does not consider any sort of dynamic stress change during the mining process. In certain circumstances, especially in multiple-seam situations, modeling a scenario of the seam of interest without considering the previous mining sequence in the off seams can potentially lead to inaccurate results. The primary objective of this paper is to present a situation where a potentially dynamic, unstable mining condition was encountered. It was not evident until the previous loading conditions in the off seams and the impact of dynamic stress changes in the active seam were considered. It is important to make the mining community aware of these potential modeling scenarios where the path-dependent nature of the mining sequence is of key importance. This paper presents a case history where room-and-pillar retreat mining was being conducted in a relatively deep cover stress regime where multiple seam interactions were present from both undermining and overmining. Mining in the active seam was being conducted with roomand- pillar mining techniques consisting of a series of parallel production panels being successively developed and retreat mined along a set of Mains. In this situation, the traditional global LaModel analysis without any path-dependent adjustments did not fully identify the area of poor conditions that were encountered. This paper explores the impacts of mining in the active seam on the lower seam which, in turn, has a negative impact on the active seam. This provided a solid foundation for the subsequent analysis of the three seams simultaneously. Based on the calibrated model, it is likely that retreat mining in the active seam resulted in increased stresses in the underlying seam that conceivably resulted in additional convergence and, most likely, additionally convergence of the pillars under the panel being developed. This in turn could have caused active subsid- The LaModel program is extremely useful for analyzing multiple-seam mining scenarios. As multiple-seam situations become even more prevalent, the potential for encountering a path-dependent mining scenario also increases. To successfully model path-dependent mining scenarios, the ground control engineer will be required to make sound judgments on the condition of pillars in sub-adjacent seams. These engineering judgments should be based not only on the current state of stress, but also on any prior or future states of stress. This means considering the stresses from over or undermining as well as stresses applied to the sub-adjacent seams from actively mining the seam of interest.

Jun 25, 2024

By Bernard F. Anderson

INTRODUCTION In this chapter, the term "down-the-hole drill" (DTH drill) is used as a generic name that encompasses the various trade names and other references such as "downhole drill," "in-the-hole drill," etc. This chapter is limited to a description of DTH drills used in stoping large underground ore bodies. DTH drills differ from conventional drills by virtue of the placement of the drill in the drill string. The DTH drill follows immediately behind the bit into the hole, rather than remaining on the feed as with ordinary drifters. Thus, no energy is dissipated through the steel or couplings, and the penetration rate is nearly constant, regardless of the depth of the hole. Since the drill must operate on compressed air and tolerates only small amounts of water, cuttings are flushed either by air with water-mist injection or by standard mine air with a dust collector at the collar. HISTORICAL DEVELOPMENT Mine managers have long known the economies enjoyed by quarry and open-pit operators in producing large quantities of ore. The savings are due primarily to the availability of massive equipment, capable of drilling large blastholes to reduce the amount of drilling, increase the fragmentation, reduce secondary blasting, and im¬prove the flow of the product. In an attempt to reduce underground mining costs, various methods are used for long-hole drilling, includ¬ing standard pneumatic percussion drifters and diamond drills. These systems have their shortcomings; percus¬sion drills are limited to small hole sizes and they ex¬perience excessive deviation and significant loss of energy with increased depth. The diamond drills provide deeper and straighter holes, but only at high cost. Both systems suffer from high noise levels, low penetration rates, and poor explosives distribution, among other problems. When the mining companies approached the drill manufacturers for a compact and portable large-hole jumbo for underground use, they specified not more than 1 % deviation on 60 m (200 ft) of vertical hole and a penetration rate of 15 m/h (50 fph). On Dec. 23, 1960, a test unit was placed in service in Montana and met the performance criteria. Though lacking the so¬phisticated features available today, the economies of surface blasting were brought underground. Unfortunately, the first system did not gain immedi¬ate acceptance in the industry. Among the factors con¬tributing to its demise were resistance to change, the need to alter development methods for the ore bodies, and a lack of flexibility in moving the rig from setup to setup and from level to level. In 1972, the mining industry again challenged the drill manufacturers to provide a workable jumbo that would combine compactness, ease of maintenance, relia¬bility, and efficiency, all on a self-propelled chassis. The manufacturers responded by providing improved jumbos, which have been accepted with enthusiasm throughout the mining industry. Today's DTH jumbos are capable of drilling from 100 to 200 mm (4 to 8 in.) diam holes that can be reamed to even larger diameters. The holes can be drilled to depths of 150 m (500 ft), depending upon ground conditions and the capability of the jumbo to retrieve the steel and drill. Fig. 1 illustrates a typical DTH jumbo. APPLICATIONS The uses to which DTH drill jumbos have been put are quite numerous, with new uses being found regularly. For convenience, these uses may be classified as primary blastholes and nonblasting holes. Primary Blastholes The original purpose for the development of the DTH jumbo was for drilling primary blastholes that could be mined by open-stope methods. Prior to the advent of the DTH jumbo, extensive development was required before production drilling could begin. Sub¬levels were required to allow access for column-and-arm stopers or ring/fan jumbos, to the extent necessary based on the effective penetration of the chosen machine. With the DTH jumbo, the mine engineer is able to reduce preproduction time and development costs. How¬ever, the most significant saving results from an im¬proved cost per ton of broken ore in the production phase. To utilize a DTH system, only a top heading and drawpoints are necessary. The top heading can be the width of the ore body with a 3.7-m (12-ft) back. A drop-raise pattern is drilled and shot to begin the stoping operation, providing a free face for subsequent blasting. A typical layout is illustrated in Fig. 2. The advantages of this system include: 1) Drilling and blasting are independent operations, and blasting can be performed at a rate congruous with the mine's ton-per-day capacity. 2) The development layout is simplified. 3) Good explosive distribution is achieved, provid¬ing more uniform fragmentation. 4) Environmental conditions for operators are im¬proved, including improved safety with all work directed downward (not overhead), lower noise levels, little fog, and a reduced dust count. 5) Improved production per manshift. 6) Simplified and easier operator work cycles. 7) Reduced cost per ton of product. 8) Fewer holes lost due to ground shifts. Nonblasting Holes With the introduction of the compact DTH jumbos, other practical uses became apparent, including the drilling of: 1) Holes for sand fill, from level to level and from level to stope. 2) Drain and dewatering holes. 3) Power and communications cable holes.

Jan 1, 1982

By Thomas D. Kaufmann

Introduction Mining has always been sensitive to the fluctuating income of downstream customer industries. The industry is now becoming more vulnerable to booms and busts as economic pulsations increase and demand for mining products shows little or no long-term growth. As the general economy has become more cyclical in the last decade, the capital-intensive primary industries have become more aware that timing as well as preparation of survival plans are vital in investment decisions. Strangely, however, some of us have not yet included the business cycle in our feasibility studies. Cyclic prices and volumes and fluctuations in profits and cash flows do not fit our linear models. The increased cyclical nature of our economy is recent and poorly understood. Forecasting peaks and troughs is still more an art than a science. Nevertheless, avoiding business cycle parameters can lead to error in value estimation and contingency planning of new projects. Metal and Mineral Industries More than half the iron and steel, aluminum, copper, lead, zinc, manganese, tin, nickel, molybdenum, cobalt, and chrome that we mine, smelt, upgrade, and recycle goes to construction, transportation, capital goods, and consumer durable industries. All are cyclical. Their products are consumed slowly, so replacement can be postponed in recessions. Purchases of such goods are usually financed by debt, and their customers are sensitive to highly cyclical changes in interest rates. During prosperous periods, people tend to buy capital goods despite high interest rates. Upstream industries also tend to be whipsawed by inventory cycles. With high interest rates and good transportation, downstream fabricators can lighten their inventories during recessions. They know that upstream suppliers can deliver supplies and raw materials immediately, And, with the advent of electronic accounting, the fabricator with timely inventory information can afford to hold fewer contingency stocks. Likewise, when recovery returns, inventories surge back through industry pipelines, accelerating demands on primary supplies. The price elasticity of most primary products is low. Their share of the value of finished products of the industries they supply is generally small. The 60 kg (130 lb) of aluminum in a car is vital. But whether it costs $80 or $130 will not visibly influence the demand for an automobile. With low elasticities of demand, the primary producer is hit with decreases (or increases) in prices and in sales volume, during recessions as well as recoveries.

Jan 6, 1984

By N. Arbiter

Evidence for the floatability of sulphide minerals without collector is analyzed and it is shown that results obtained with ores, in contrast to those with single minerals or mineral mixtures, depend on many additional variables, some identified and others not. Because of the prevailing low levels and costs of collectors for most sulphide ores, it is unlikely that collectorless flotation will have commercial applications, so that continued research on the subject may be justifiable on theoretical but not on practical grounds.

Jan 1, 1993

By Joyce Lappin-Randolph

In 1977, Vertical Crater Retreat (VCR) Mining was developed at the Homestake Mine and by 1983 had become a fully integrated mining method contributing 60% to total underground production. VCR has proven successful for continuous ore blocks exceeding 55,100 tons (50,000 st) with dips greater than 60" and provides a productivity average of 39 tons (35 st) per man shift (tpms) which is 92% greater than Open Cut-and-Fill. Discontinuous ore bodies, small pods, or flat structures not amenable to bulk systems are mined with Mechanized Cut-and-Fill (MCF) and have been able to achieve a 32 tpms (29 st) average productivity. Small, low grade, remnant ore bodies were not economically viable with large scale bulk techniques and couldn't support the development required for a MCF system. As a result, Homestake began researching modified bulk mining methods to increase production rates and maintain safety, while lowering costs. A modified version of VCR with significantly diminished development was prototyped in an effort to reduce initial capital investment and expedite the production phase. This modified method is called Small Block Vertical Crater Retreat (S. B. VCR). Geology The Homestake Gold Mine is located in the northern Black Hills of South Dakota at Lead. Having been active since 1876, it now extends from the surface to the 2,440 m (8000 ft) level underground.

Jan 1, 1987

By I. Mazalov, G. Ospanova

Introduction Today, uranium is of great interest because of its application to nuclear power and nuclear weapons. Kazakhstan has been an important source of uranium for more than fifty years. All uranium products are exported. Results In Kazakhstan uranium exploration started in 1948 and developed in several parts of the country thru mining of hard rock deposits. There are known around 50 uranium deposits in six provinces: Shu-Sarysuyskaya (57%), North Kazakhstan (18%), Syrdaryinskaya (15%), Ilyiskaya (7%), Caspian (2%), Balkhash (1%). In the Northern Kazakhstan province, KazSabton took over Tselinny Mining & Chemical Co in 1999. In this province the stockwork is of Paleozoic and Paleozoic folded complexes origin. In the Balkash province some mining of volcanogenic deposits occurred during the Soviet era. This province’s stockwork is of Endogenous origin.In the Ili province uraniumis mainly found in uranium-coal deposits formed by oxidation of the lignite beds roofs. In the Caspian province the Prikaspisky Combine operated since the 1960s a major mining and processing complex on the Mangyshalk Peninsula. This led to the founding of Aktau. It was privatised as Kaskor in 1992 and operations ceased in 1994. The uranium occurrence is associated with the phosphorous from fossil fish bone detritus conglomeration. In the Chu-Sarysu province, which has more than half the country's known resources, both Stepnoye and Tsentralnoye have been operating since 1978 and 1982 respectively. Uranium mineralization occurred in the regional stratum oxidation zones. In the Syrdarya province slightly to the west of the province’s center the No.6 Mining group has been operating since 1985. Uranium mineralization occurred in the regional stratum oxidation zones.

Jan 1, 2007

By V. J. Hucka

A 0.5 m (20 in) diameter high pressure natural gas pipeline crosses over a coal mine located in Central Utah. Ground movement induced by the mining operation could possibly place excessive strain on the pipeline causing it to rupture. The mining operation extracts coal from two seams using the room and pillar method. The seams are situated one on top of the other and both lie directly under the pipeline. At present, only the upper seam is being mined beneath the pipeline. However, in the future, the mining operation of the lower seam will also affect the pipeline. As would be expected, mining of both coal seams causes surface subsidence. This is especially true when the pillars are extracted during retreat.

Jan 1, 1983

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By William L. Young

I think I should let you in on one of Canada's best-kept secrets, if you will promise not to tell it all over the place. Believe it or not, good, honest, enterprising capitalism is still alive and flourishing north of our common border, and I am living proof that capitalism is still working for the little guy. My personal story of mining development in Canada isn't all that rare -- you've probably heard something like it from other areas and other days several times -- but my case brings it up-to-date. I would like to Tell you briefly the history of Northumberland Mines Limited, a contemporary case of individual enterprise getting a mining operation underway. And if I can do it you probably can too.

Jan 1, 1981

By F. H. Seymour

Central to Newmont Gold's Mine planning system is the ability to interactively perform cut and fill operations on topographic contours and to accurately evaluate grades and tonnages within contour outlines using polygon set manipulation routines. This paper develops the applied geometry concepts that underlie these routines. Included are representation of volumes with contours, point in polygon test, block proportion in polygon calculation, polygon area and centroid calculation, and intersection, union, and complement between polygon sets.

Jan 1, 1990

By G. Pan

A geostatistical approach is proposed for the design of infill drilling programs. The method is consisted of three major steps: developing geological favorability models, delineating mineralization and ore envelopes, and classifying reserves or resources. Geological modeling aims at developing favorable geological zones in which drilling is designed. Modeling mineralization and ore envelopes establishes criteria on potential blocks to be drilled. Top target blocks should be those included within ore envelopes. The framework of resource categories includes five types: probable reserves, indicated reserves, indicated resources, possible resources, and barren. Indicated reserves or resources are the top priority to be drilled for the definition of minable reserves. Possible resources may be considered as targets for further exploration. The algorithms involved in the analysis include indicator favorablity analysis, ordinary kriging, and indicator kriging. A case study presented here involves a gold deposit of Carlin type. The deposit was delineated by a sparse drilling program with 230 feet of average spacing. The infill drilling program designed by the new method suggests a significant reduction on the number of holes from a regular-grid infill drilling pattern.

Jan 1, 1995

With the rapidly growing use of hydraulics in mining equipment, maintenance personnel should be familiar with the various components in hydraulic systems. Hydraulic systems do wear out - the fluids they transport are hot and turbulent, the equipment they power often imposes tremendous pressure pulsations and bending stresses, and the working environment is harsh. Therefore, even though hydraulic hoses are made of remarkably trouble-free components, they do need to be replaced periodically. There must be coupling methods that allow hoses to be replaced without disturbing other components. Couplings must also provide a variety of leak-resistant connections between hoses and other components in the hydraulic circuitry. Threaded Connection and Seals Hydraulic coupling thread ends and sealing arrangements are standardized, with many types available. Their outward appearance varies, but coupling configurations are recognizable by examining threads and seals and comparing them to the examples provided here. Iron Pipe Thread There are two kinds of iron pipe threads normally used in mining equipment circuitry - National Pipe Tapered Thread for Fuels (NPTF) and National Pipe Straight Thread Mechanical Joint (NPSM). The NPTF seal is the engagement of the coupling threads, called thread interference. When tightened, the tapered thread of the male fitting binds into that tapered thread of the female fitting to form a relatively leakproof seal (Fig. 1). In the NPSM seal, there is a 30° angle seat machined into the end of the male NPTF fitting. This seat engages with a mating 30° angle cone on the inside of the female fitting. Female NPSM fittings have straight threads, as opposed to the tapered threads of the NPTF fittings. However, most NPTF solid male fittings also have a 30° angle seat enabling them to be used with NPSM female fittings (Fig. 2). JIC and SAE Fittings Joint Industry Conference (JIC) and Society of Automotive Engineers (SAE) seals are formed by joining two mating, conical metal surfaces. The coupling threads are used to bring and hold these surfaces together to form a leak-resistant seal. A JIC connection is a solid male threaded end, with a 37° machined male nose, mating with a 37° female flare seat. When connected, the mating surfaces are held together by the threads, but the threads do not form the seal. The female seat is created by flaring a tube end or machining the interior surface of a stem to 37°. A female JIC has a swivel nut, allowing the sealing surfaces to be joined together without twisting a hose or twisting the seats against each other (Fig. 3). JIC couplings are frequently used on low, medium, or high pressure hydraulic circuits on mining equipment and machinery. The SAE connection is similar in appearance and sealing characteristics to the JIC system, except the angle of the machined male nose and female flare seat is 45° (Fig. 4). "O" Ring Fittings Seals for "O" ring fittings are formed by compressing an "O" ring against an exposed machined surface on a mounting block or hydraulic component part. The "O" ring must be compatible with the type of hydraulic fluid used (Fig. 5). An "O" ring boss connection is made of a male straight thread

Jan 10, 1983