Search Documents

By E. P. Fahrenthold, K. E. Gray

Introduction Brine reservoirs along the Texas and Louisiana Gulf coasts are currently under study to investigate the technical and economic viability of production wells designed to extract methane gas in solution. The effect of well pressure drawdown on reservoir rock and associated overburden material is important to well performance predictions and the analysis of potential subsidence problems. Consequently a series of compaction tests have been conducted on sandstone and shale cored from a test well drilled near Hitchcock, Texas, in order to determine the variation of mechanical properties to be expected over the producing life of the formation. Previous Work The referenced tests are part of an extended study of geopressured-geothermal reservoir behavior, including compaction (Jogi, Gray, Ashman, and Thompson, 1981 and Jogi, Kalra, Gray, and Thompson, 1981) and creep (Thompson, Jogi, Gray, and Richardson, 1981) tests of reservoir rock and related reservoir performance studies (Rago, Okhuma, Seperhnoori, and Thompson, 1985). Recent work has considered the nonlinear constitutive behavior of sandstone (Fahrenthold and Gray, 1985 and 19861, while additional experimental work is reported here. Geological structure and composition of the Hitchcock field from which the core samples were obtained is discussed by Light (1985). Experimental Procedure Compaction tests were conducted on cylindrical cores, nominally 2.75 inches in length and 2 inches in diameter, with independent control of the axial, confining, and pore pressures. Axial and radial deformation of the samples were measured in tests over a range of effective stress states expected to develop over the reservoir lifetime. The term effective stress as used here refers to the algebraic difference of the total stress and pore pressure, with compression taken as positive. Three types of compaction tests were conducted on the sandstone. In the uniaxial tests, axial total stress and radial strain were held constant as the pore pressure was reduced, similating one dimensional compaction which may occur during reservoir depletion. In the triaxial tests, radial total stress and pore pressure were held constant as the axial total stress was increased, duplicating conventional rock compaction test procedures. In the pore pressure drawdown tests, axial and radial total stresses were held constant while the pore pressure was reduced, in order to investigate differences in sample response to mechanical and pore pressure loading. Compaction tests were also conducted on shale material obtained from the reservoir overburden. The field coring process provided few consolidated shale sections sufficiently large to allow preparation of samples with the dimensions described above. With additional attrition during sample preparation of this brittle material, ultimate yield of the coring effort was limited. The few available samples were tested in uniaxial and triaxial tests similar to those described above. The use of displacement transducers to measure sample deformation avoided the difficulty of strain gauge installation on this material. Test Results The sandstone and shale both demonstrated nonlinear stress-strain behavior, with hysteresis and residual strain present upon unloading. Polynomial interpolation of the stress-strain curves was used in the calculation of incremental values for the loading and unloading moduli. Figures 1 and 2 show example axial effective stress-axial strain curves for triaxial tests conducted on sandstone and shale samples. The figures plot incremental stress and strain variables, defined as deviations from the state of prestress to which the sample was subjected. The state of prestress was varied between tests in order to investigate material behavior over the entire stress and strain space of interest. Tables 1 and 2 give the incremental moduli (Young's modulus and Poisson's ratio) as a

Jan 1, 1986

By G. Wheeler

Epithermal gold exploration in the last decade has developed useful models for exploring new ore districts in Oregon. In Eastern Oregon, disseminated gold occurs in epithermal deposits that have been pervasively silicified and brecciated. Many gold prospects staked since 1980 are in fluvial and lacustrine sandstone and conglomerate deposits. Clay alteration products and disseminated pyrite may be present. Vein filling calcite and thin to thick quartz veins are common. Late stage quartz forms pseudomorphs after calcite in many deposits. Arsenic, mercury and gold are geochemically anomolous but silver is usually not. The epithermal deposits are located in part of the Deer Butte Formation or equivalent units. Exploration criteria include the presence of Deer Butte Formation or correlative units and NW structures cut by N-S basin and range structures.

Jan 1, 1987

By Madan M. Singh

It is estimated that through 1975, there were 1.69x109 m2 (418 000 acres) of urban land threatened by potential subsidence due to mining with a value of over $12 billion (19;3 dollars; USBM, 1979). With increased coal production to meet the energy needs of the nation, both these figures may be expected to increase. Hence greater attention to controlling surface damage due to subsidence is merited. In fact, the Surface `lining Control and Reclamation Act of 1977 (SMCRA) (Public Law 95-87) mandates that underground coal mining operators "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, ..." The term "subsidence," as used in this paper, implies the total phenomenon of surface effects associated with the mining of minerals, and not only vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By Paul M. Jr. Musgrove, Thomas D. Henderson, Mark B. Nesbitt

Introduction History. Vat leaching operations began in October 1953. Since that time, about 4.2 million tpy of oxide ore averaging 0.72% copper have been treated. Economic conditions, improved operating methods, and increased production facilities have allowed the ore grade to be reduced over the years. The average ore grade was 0.84% Cu during the 1950s, 0.68% in the 1960s, and was 0.50%, or below, during the 1970s. By 1961 some 35 million tons of oxide ore had been removed from the mine, exposing the underlying sulfide ore body. A 5,000¬ tpd concentrator was constructed and put into operation to treat the sulfide ore in November 1961.1 The original crushing plants were used for both oxide and sulfide ores, but by adding a third crushing shift, six days per week, the total ore treated was raised from 12,000¬17,000 tpd. Dwindling oxide ore reserves prompted expansion of the concen¬trator to 13,500 tpd in 19672 so that exhaustion of known reserves of both ores would occur at nearly the same time. Again, no additional crushing facilities were added during the expansion. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to about 9,000 tpd. Instead, the addition of two crushing shifts per week and improved operating procedures have increased the treatment rate to 26,500 tpd-13,000 tpd to the leaching plant and 13,500 tpd of sulfide ore treated in the concentrator. Geology. The Yerington ore body is a disseminated porphyry copper deposit where a quartz monzonite porphyry intrusive contains the major part of the ore values, with some copper mineralization found in the adjacent granodiorite and other rocks. The geology of the Yerington Mine was aptly described by J. R. Wilson (Mining Congress Journal, June 1963). The ore body is one of few porphyries where geologic conditions were optimum for the formation of an important concentration of oxidized ore with minimum economic effect of secondary enrichment. The principal mineral in the oxidized zone is chrysocolla, which irreg¬ularly occurs dispersed throughout the rock and as narrow seams along fissures. The grade of the ore in the oxidized zone is generally the same as in the primary sulfide below, although some massive concentrations do occur as vein-like fissures and as filling of breccia zones. Cuprite, tenorite, melaconite, malachite, and azurite occur but are not abundant. Lying between the chrysocolla horizon and the primary sulfide is a transition zone whose limits are irregular but seldom with vertical range exceeding 50 ft. Chalcocite, cuprite, melaconite, native copper, and chrysocolla occur superimposed on the primary sulfides. Chalcocite replacement of chalcopyrite, as well as secondary chalcocite, do occur. The primary sulfide minerals are chalcopyrite and pyrite, with minor amounts of bornite and covellite. There are no appreciable gold or silver values, and molybdenite has rarely been noted.

Jan 1, 1985

By Martín Antonio Encinas‐Romero, Patricia Guerrero‐Germán, Jesús Leobardo Valenzuela‐García, José R. Parga‐Torres, María A. Bracamontes‐Landavazo, Agustín Gómez‐Alvarez

A study was carried out to process a sulfide mineral concentrate from Norwest of Mexico containing 97 g/t Au, 0.15% Cu, and 15% Fe. An oxidative acid pretreatment was investigated using ferric sulfate as oxidant, followed by leaching of gold with sodium cyanide. Scanning electron microscopy, SEM-EDS, and X-ray diffraction, XRD, the analysis confirms the presence of quartz and pyrite species. First, a leaching was carried out without pretreatment, at ambient conditions, T = 25 °C and P = 1 atm, obtaining only a 45.2% gold extraction. Once the presence of Fe and Cu sulfides had been confirmed, the Eh-pH diagrams were constructed for the Fe-S-H2O and Cu-S-H2O systems, where it is appreciated that pyrite and chalcocite can dissolve with high oxidation potentials and forming sulfur, oxidizing to sulfate at highly acidic conditions. The oxidized concentrate was neutralized and adjusted to pH > 10.5; it was leached at ambient conditions, at different particle sizes, 44, 37, and 26.5μm, achieving an Au extraction of 75% using a concentration of 0.5% NaCN, 26.5μm particle size, 20% solids, and P = 1atm. Then the oxidized material was subjected to different temperatures, 25, 50, and 70 °C, under the same conditions and obtaining Au extractions up to 92% at 70°C. Additionally, the leaching process was compared using an autoclave reactor at moderate pressures, obtaining an increase in the extraction of Au up to 98% in 2 h, at T = 70 °C and P = 0.62 MPa.

Jan 23, 2022

By K. J. Shelswell

This work describes the design, analysis, and comparison of discrete simulation and static spreadsheet models developed to compare the oreflow efficiency of two conveyor-based material handling systems; one approach with a conveyor stream in series and one with parallel conveyor streams. Analysis and comparison indicated that daily rates were significantly affected by random conveyor failures in both designs. The compound effect of random failures limited the effectiveness of long belt assemblies in series, while the parallel conveyor stream design partially alleviated this constraint. The static spreadsheet model predicted a lower average daily oreflow rate for the series conveyor stream design and a higher average daily oreflow rate for the design with parallel conveyor streams when compared to the discrete simulation results. These discrepancies were the product of model sensitivity to operational factors incorporated in the system and provided the opportunity to further use the discrete simulation models for trade-off comparisons and sensitivity breakdowns of mine operating practices and material handling system efficiencies in both the series and parallel belt stream designs

Feb 23, 2014

By Hans W. Schreiber, Rudi P. Fronk

IINTRODUCTION Widespread activities in precious metal projects in the western U.S., Australia, Canada and other parts of the world have opened a flood-gate of consul- ting expertise to aid and accelerate the development process. Utilization of outside expertise has taken on many shapes and forms that have in some instances actually "decelerated" or "retarded" project progress. Small mines are especially vulnerable to apparent false-starts and misdirections, be- cause of their generally lower capital commitments, shorter lead times and limited mineral in-house expertise. Mine development for small mines requires fundamental approaches by knowledgeable consultants that are timely and cost-efficient and in line with accelerated development, if they are to be successful. The development process is obviously that process which brings a given deposit into production. Or, put another way, the process comprises all activities, decisions and commitments which take place from the moment an authorizing entity (usually a board of directors) com- mits to development and production (usually on the basis of a final feasibility study) until the first ton of ore is processed to a saleable product. The activities, decisions and commitments over a development period--such a period can range from as short as a year or less to as long as 5 years or more--are many, highly varied, and often interdependent. The development period is also particularly risky, not only because of the varied and interdependent decisions and commitments, but also because of capital demand amounts. Delays in the development process are thus particularly costly - sometimes so costly that small and often undercapitalized mining companies, failing to reach production and a cash flow within a planned period, face, if not bankruptcy, at least severe equity dilution or particularly onerous and restrictive covenants on additional loan financing. It therefor behooves especially small mining companies to examine ways to accelerate development. By doing so, the development process may actually meet planned scheduling. The development process generally comprises environmental impact studies completion, final engineering, permit- ting, financing, equipment and machinery procurement, contractor selection and construction -- such activities largely being overlapping. The paper addresses what the small mines operator or the small mining company can do with consulting firms to accelerate development. By "small mines" is meant open pit operations of 2000 tpd or less and underground operations of 500 tpd or less. By "consulting firms" is meant entities who do not possess an engineering and construction capability, such as Derry Michener Booth & Wahl, Pincock Allen & Holt, Behre Dolbear-Riverside, etc. The paper concentrates on gold projects. PRIORITY CONSIDERATIONS Of the items listed in the previous paragraph which comprise the development process, the two which most consistently appear to cause delays are permitting and financing. The former's delays can be due to political overtones and thus the delays may not be reasonably foreseeable. The latter's delays are most often due to inadequate preparation, and thus are avoidable. For the reason stated above, and considering that financing is fundamental to all of the activities which constitute the development process, the paper focuses on financing as the priority item which can most assist in accelerating or retarding the development process.

Jan 1, 1987

By A. Bascetin

Materials produced in quarries have been used for different intentions such as concrete and cement raw material, asphalt and embankment aggregates, railway ballast. Especially in cement manufacturing, the chemical composition and the uniformity of the raw materials play a strategic role in the economy and quality of the cement process. Therefore, it is necessary to achieve uniformity and desired chemical composition and maintain these at all production stages according to the type of cement produced. To achieve this goal the production planning and pit design play an essential role. This paper briefly outlines the production optimization of cement raw materials in a quarry in Istanbul western part of Turkey. For the purpose it was used the 3D ore body modeling and the geostatistical techniques. The variation of chemical components (%CaO, %Al2O3, %Fe2O3 etc.) and quality control parametres (LSF, SR, AR and etc.) obtained from the quarry were determined. Then the values of unknown chemical components and quality control parameters in the ore body were estimated using Kriging which is one of the geostatistical interpolation methods. The open pit design was also created by specifying wall slopes and taking into consideration of the grade distributions of the benches. The most important revolution in the paper is investigating the effects of the block dimensions in block modelling which is important for reserve estimation. The other important point in the study is using the different range values in variogram analysis for determination optimal reserve estimation. n this study, the effects of two parametres on reserve and waste amount estimation were determined according to CaO% distribution. The study was pointed out that the changing of the two parameters are very important for the optimal mine planning and environmental considerations.

Jan 1, 2010

By Adrian Molinari

A radioisotope probe (Minexan 202) capable of simultaneously analyzing a mineral slurry for five elements and pulp density has been developed by Outokumpu Oy, Finland. The probe is designed to operate immersed directly in a process stream, or it can be equipped with a flow cell through which passes a continuous sample of the main stream. A minicomputer (PDPII) is used to control the probes and calculate the assay data. This paper describes the probe as applied to slurry analysis and compares it to the conventional x-ray on-stream analyzer (Courier 300).

Jan 1, 1977

By G. Plenge, M. Brittan

"Plant design parameters for gold extraction, leach residence time and cyanide consumption are generally determined from standard bench-scale bottle roll or agitation leach tests. The application of laboratory data to process design has essentially evolved from the testing of oxide or low cyanide-consuming ores. Such scale-up factors may not be appropriate for ores that deplete cyanide and oxygen since this interferes with gold extraction kinetics. High cyanide-consuming ores also exacerbate the differences between the conditions applicable to small batch tests and large continuous operations. Testing a reactive high-sulfide South American ore deposit necessitated the re-evaluation of conventional bench-scale cyanidation procedures. Pulp density can be a major factor affecting the results for plant design purposes and should be treated as a test work variable. As with high clay-bearing ore, where pulp viscosity can hinder mass transfer, minimizing the influence of test equipment on gold extraction kinetics may require low pulp densities. This introduces interpretative complexity since cyanide consumption changes as a function of pulp density. Activated carbon also consumes cyanide, so its effect has to be accounted for in the case of carbon-in-leach (CIL) or carbon-in-pulp (CIP) plant flowsheets. Since cyanide is an expensive reagent, often a major component of plant operating costs, it is important that the scale-up of cyanide consumption from laboratory to plant be representative. The traditional method of reporting cyanide consumption in bench-scale testing is questioned since it takes credit for residual free cyanide in leach tails. The projected plant consumption may be better estimated by using the total cyanide addition in a laboratory test. We propose a test work protocol that categorizes the cyanide consumption into its components but requires more extensive testing to generate design data. The ultimate validation of scale-up factors used by project engineers requires rigorous bench-scale versus commercial plant comparative data. Such data are not readily available.IntroductionMajor factors in the design of a gold processing plant are gold recovery, leach residence time and cyanide consumption. These parameters are important determinants of project revenue and costs and, thereby, potentially of project financial viability. Estimates of the associated design criteria for a commercial plant are normally generated from laboratory cyanidation, carbon-in-leach (CIL) or carbon-in-pulp (CIP) tests using standard procedures (Angove, 2005). The key question is whether the standard laboratory test work procedures developed historically for low reagent consuming ores are appropriate for ores that are highcyanide and oxygen consumers.The present paper examines test procedural factors that can influence the test work results and, therefore, their interpretation for design scale-up purposes. The study refers in particular to a high cyanide-consuming sulfide ore. The ore was being tested to develop scoping level engineering design criteria for a proposed project in South America."

Jan 1, 2015

By Thomas P. Meloy

Theoretical development of comminution models has come about in the last 10 years. These models assume that the material being broken is homogeneous and that the compression or energy wave is uniform throughout the specimen. Obviously, this is not the case because most comminuted materials are rocks with either many phases and/or definite grain size. The mathematical models deriving the size distribution of daughter fragments resulting from the comminution of brittle, single particles are of two schools. The first model, proposed by Gilvarry in 1961, was based on the concept of volume, surface, and edge flaw activation. The second, proposed by Meloy in 1960, was based on the concept that the crack density is a function of the energy in the comminution wave. The flaw theory has run into increasing theoretical problems and is now being abandoned. On the other hand, the crack density theory has been expanded and has successfully considered the case where there are inhomogeneities in the comminutive wave. However, the main constraint of a homogeneity in the solid being comminuted has hitherto never been overcome. In this paper, a very general derivation of the crack density model is made for inhomogeneous solids by replacing the assumption of homogeneity with an arbitrary function, P(y), which describes the susceptibility of the material to comminution as a function of position. The restraints on this function, P(y), are very broad and, hence, the derivation is extremely general. General use of the equation derived necessitates a detailed a priori knowledge of both the fracture process and of the physical properties of the material being fractured; this knowledge is expressed in open form as, P(y), the linear probability density that a plane of fracture intersects at point y on an arbitrarily oriented line segment of total length xo through the original particle. From these assumptions, a general expression for the cumulative mass distribution of particles resulting from fracture is then postulated. It is: [ ] where, B(x), is a cumulative mass of material finer than size x, r is the average number of crack,, (y), is defined above and xo is the initial particle size. It is shown that suitable assumptions reduce the expression to the theoretical results of Gaudin and Meloy and to special forms of the empirical equations of Rosin-Rammler, Gaudin and Schuhmann. Semi quantitative agreement is demonstrated by Grimshaw with experimental results of a very complex fracture of heterogeneous sandstone blocks. A need is expressed for more theoretical development of P(y), and a more extensive experimental study of both homogeneous and heterogeneous fracture. The full mathematical derivation is presented for the first time in this paper. The general implications of the equation and its application are also discussed.

Jan 1, 1968

By Shani Engelbrecht, Belinda McFadzean, Avuyile Wali, Natalie Shackleton, Vratislav Malysiak

Frothers play a crucial role in sulphide and PGM ore flotation recovery, and AECI Mining Chemicals studies on PGM ores have shown significant flotation kinetic increases with the optimal frother-collector combinations. Using Senfroth 200 as the industry baseline, remarkable kinetic increases were observed with AECI Mining Chemicals developed frothers in the first concentrate. Even in the worst-case scenarios, 4E PGM recovery increased by 5% at a slightly higher concentrate grade. It is important not to limit frother dosage to a fixed value. Instead, enough frother should be added to maintain a stable bench float, measuring the dosages by frother volume before and after tests. Frothers can be specialized blends and their importance should not be underestimated. The results produced by formulating and innovating frothers to address specific industry challenges have been encouraging. Testing a frother on a plant scale does not have to be as daunting as with collectors, enabling the identification of the best frother-collector combinations at an industrial scale. AECI Mining Chemicals bench scale testwork has motivated plant-scale trials that have successfully transitioned to commercialization. This paper compares the results from metallurgical and froth stability tests and shows that occasionally frothers that have a less stable froth can have improved valuable mineral recoveries, while still exhibiting better drainage for reduced entrainment and mass pull. It was shown that caution should be used when relying only on simplified froth stability tests in the evaluation of new frothers.

Feb 1, 2025

By E. A. Domínguez

Kaolin deposits of Patagonia (Argentina) were formed by ?in situ? alteration of volcaniclastic rocks or by erosion, transportation, and deposition of residual clays in small basins. The mineralogy, geochemistry, grain size distribution, and specific surface area of natural and washed kaolins were studied in order to point out the relationships with the ceramic process. Primary kaolins are coarse-grained, kaolinite+quartz±halloysite, with a very low specific surface area. Sedimentary clays are either kaolinitic?smectitic and very fine-grained or kaolinitic with a coarser particle size distribution. An interdependence between mineralogy, chemistry, particle size distribution, texture, surface activity and ceramic behavior was found. Plasticity is strictly dependent on surface activity and expandable clay minerals. Slip rheology is affected by soluble salts, smectite, and tubular halloysite. Kaolinite-halloysite play an opposite role versus smectite-I/S in slip casting and tile pressing. Kaolinite and quartz are beneficial for drying behavior while expandable clay minerals increase drying sensitivity. Firing behaviour is mainly affected by minor components supplying fluxing oxides.

Jan 1, 2010

By John M. Moore

Within the Pofadder district of Namaqualand, South Africa, economically exploited deposits of bedded barite and zinc-lead-silver-copper sulfides occur in close proximity within highly metamorphosed mid-Proterozoic pre-tectonic para¬gneisses of the Namaqualand Metamorphic Complex (NMC) (figure i). The paragneisses belong to the Bushmanland Group (SACS, 1980) that comprises a relatively straight-forward regional sequence of basal leucogneisses, intermediate mica-sillimanite schists and glassy quartzites, and a mixed upper zone of banded iron formations (BIF), minor marbles, quartz muscovite schists and localised uppermost quartz-pebble conglomerates and amygdaloidal mafic gneisses (Joubert, 1974) (figure ii). The base metal and barite mineralisation occurs in close association with BIFs, generally above the glassy quartzites, although in some cases possibly below them. In the regional context, the Bushmanland Group paragneisses are, to the north, intercalated with and ultimately replaced by meta-volcanic sequences of talc-alkaline affinity (Reid, 1977) belonging to the Orange River Group (SACS, 1980). The metavolcanics are generally of acidic to intermediate composition and show evidence of subaerial formation from 'high altitude shield volcanism' with many acidic ashflow and welded tuff bands, mesocratic and lesser melanocratic lavas and some fanglomerates (Ritter, 1980). To the south and east, the schist/quartzite associations are initially intercalated with and eventually replaced by cordierite gneiss/metacarbonate/biotite gneiss associations of shallow marine affinity (Moore, 1980a). The Bushmanland Group paragneisses appear to represent sedimentary material in the extreme distal portions of a talc-alkaline volcanic environment adjacent to a shallow platform sea.

Jan 1, 1983

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By Jr. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photo-elastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface and, (3) the effects of subsidence on tension in the truss members.

Jan 1, 1989

By Yucheng Li, De Huang, Yonghong Liu

Mine frictional resistance is one of the essential parameters of mine ventilation systems, and it is of considerable significance for the prevention and control of mine risks and accident hazards. Frictional resistance requires a lot of resources and time and has errors. To reduce the errors of frictional resistance, a regression model of frictional resistance is proposed based on the correlation analysis of the affecting factors. Through the comparative test analysis of seven regression methods, it is found that the classification and regression tree method for solving the proposed regression model has better performance than other methods. The least square error criterion is used to calculate and rank the importance of the factors affecting frictional resistance. The results show that the cross-sectional area of the tunnel, the support method, and the presence or absence of devices or pedestrian ladders have the most considerable influence on the prediction accuracy of frictional resistance. The support methods and cross-sectional areas are essential input variables. Through the combination test analysis of the influencing factors, the results show that the regression model does not have predictive ability when the number of input variables is less than 3 and the best predictive performance cannot be obtained using all the influencing factors. The best prediction model of resistance is to combine the shape of the tunnel, the support method, the presence or absence of devices or pedestrian ladders, and the cross-sectional area. The method proposed in this paper does not require a lot of resources and time investment, and the frictional resistance error is small. At the same time, it solves the problem of resistance prediction with incomplete data of influencing factors and provides a compelling new method for obtaining frictional resistance parameters.

Jan 28, 2022

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By Jurgen Weissflog

Why, where and since when using shiftable conveyors? Advantages of this equipment The ever increasing demand for bulk materials such as ore, coal, lignite, oilsand, oilshale and bauxite requires mainly an opencast operation. To exploit these materials huge amounts of overburden and partings must be transportes by means of conveyors, trucks or trains. When analyzing the various opencast mines it can be established that there exist only two basic types of mining systems, i. e., the discontinuous strip mining system as used in the USA (Fig. 1) and the continuous mining system as is commonly applied in Europe. The reason why these two mining methods have been developed parallel to and independently of each other to such a high technical standard results from the varying geological conditions of the mineral deposits.

Jan 1, 1983

By Robert McIvor

The following is a summary of the Robert H. Richards Lecture on “Learning and Good Fortune on the Road to Discovery” presented at the Mineral & Metallurgical Processing Division (MPD) Awards Plenary Session on Feb. 23, 2026 during the MINEXCHANGE 2026 SME Annual Conference & Expo in Salt Lake City, UT.

Mar 1, 2026