Search Documents

By John E. Caffrey

Mr. William. J. Montgomery in his book "Theory and Practice on Mine Ventilation stated "Ventilation is vitally important to underground mining for three reasons: First, it sweeps all workings with a plentiful supply of air and drives to the outside the smoke, gases, and contaminated air which would be injurious to the miners; second, it dilutes and renders harmless the explosive gases emitted from the strata, thus eliminating the dangerous conditions caused by the accumulation of these gases; third, it keeps the mine air as nearly as possible of the same composition as the outside air, thus giving to the miner the healthiest possible condition in which to work...." Specific methods to achieve the above basic reasons for mine ventilation were established in the Federal Coal Mine Health and Safety Act of 1969. Sections 303(y)(1); (y)(2), and Section 317(f)(4) of the Act, which can be broadly described as entrapment features, are controversial and debatable in the minds of many mining engineers in their intent and method for affecting, 303(y)(1) in certain cases prohibits the use of belt haulage entries as an intake for face ventilation, This is to say that air traveling in a belt entry will be placed into the returns and not used for face ventilation, 303(y)(2) limits the velocity of the air on trolley haulage entries. The regulations, as published in the Federal Register, have set this limit at 250 feet per minute unless a higher velocity is approved by the District Manager.

Jan 1, 1972

By Robert D. Harris

In 1958, the coal industry, through Bituminous Coal Research, Inc., and the electric utility industry, through the Edison Electric Institute and the Association of Edison Illuminating Companies, initiated a joint program to study coal pyrite and its removal as a means of lowering the sulfur content of steam coals. It was assumed that significant amounts of pyrite often remained in washed steam coal not because available systems for coal cleaning were inadequate, but because the pyrite was small and widely disseminated, During the first two years, samples of coal were examined petrographically to determine the size, association, and mode of occurrence of the pyrite in the raw coal and in the products of laboratory separation, Samples of coal were also pulverized in different equipment to determine how effectively pyrite was released by pulverization and if the mode of pulverization affected the liberation of pyrite. From these studies, the following tentative conclusions were made (1 ): 1. Much of the coal pyrite is within a 250-70 micron size range, and therefore is too small to be removed by conventional coal cleaning, but relatively large when compared to the size of coal as pulverized for combustion in large boilers. 2. The degree of pyrite liberation is mainly determined by the size of the product and not by the type of crusher. 3. For improved pyrite removal, the coal should be cleaned during or after pulverization at the power station.

Jan 1, 1965

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By F. A. Molloy

As a result of feasibility studies made in 1975 a 3-0 seismic reflection survey was shot over part of the Veendam salt pillow during 1978-1979. The Zechstein salt pillow, located in the northeast of the Netherlands near the town of veendam, occurs at a depth of 1400 m and contains three carnallite rich horizons over an interval of 300 m below top salt. MgCl2 brines are produced from these layers as feedstock for a magnesia plant, which starts up in 1981. Prior to the acquisition of the seismic data four wells had been drilled. The thickness of the carnallitite layers encountered in these wells varied between 50 and 125 meters. In view of these variations it was necessary to obtain a reliable isopach of the different layers. The 3-0 seismic survey covered an area of ± 4x4 km with a sampling interval of 20 m in all directions. The data was recorded it an area array using a 120 channel instrument. Final presentation of the data was in the form of 3-0 migrated acoustic impedance cross sections. The quality and resolution of the seismic data allowed reliable structural and isopach mans to be made. It was shown that the carnallitite layers are continuous over the area surveyed, whilst local thickening is "fault" related. Having this information brine production locations could be choosen in the thicker parts, allowing maximisation of production potential whilst avoiding faults and fulfilling mining regulations. A subsequent benefit of this approach is the possibility of using the seismic data to predict ore grade. Using the available wells as calibration points the acoustic impedance response of the seismic at the well was matched to the ore grade found. From these points a synthetic section was made with varying ore grades. Pre¬liminary results are encouraging and the liability of this predictive tool will be evaluated in the light of future drilling.

Jan 1, 1981

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By R. F. Merwin

Advancement in automation intensifies the need to remove tramp iron from bulk materials being processed and carried on belt conveyors. Although magnets have long been employed for this purpose, it becomes increasingly necessary that magnetic equipment of appropriate types and sizes be selected and advantageously installed -- if maximum benefits are to be derived Tramp iron present in bulk materials consists of ferrous trash, such as wire, bolts, nails, equipment parts, tools, and machine cuttings. The results, if the iron is not removed, are damaging to equipment having close clearances, explosions, or fire, En the case of flammable materials, production downtime losses, and contaminated products.

Jan 1, 1966

By R. Asmatulu

According to Darcy's law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By Theodore H. Budd, Douglas J. Heinz

This report concerns the successful construction of Contract No. 287 of the Northeast Side Relief Sewer System for the Metropolitan Sewerage District of the County of Milwaukee. The contract involved the construction of approximately 3316 meters (10,880 feet) of tunnel concrete lined to 1.83 meters (72 inch) internal diameter; 30.48 meters (100 feet) of 1.83 meters (72 inch) reinforced concrete pipe jacked-in-place; a river crossing of approximately 107 meters (350 feet); 197 meters (647 feet) of 1.83 meters (72 inch) reinforced concrete pipe in open-cut; several diversion and flow monitoring structures; and miscellaneous manholes and appurtenances. The contract proposal, which was extremely prescriptive, did allow alternative methods of primary support consisting of precast reinforced concrete segments, steel liner plates, steel ribs with wood lagging, and combinations thereof in designated areas. The specifications required the contractor to designate which support scheme it intended to use. The specifications also required compressed air as a means of ground water control for approximately 2316 meters (7600 feet) of tunnel. The alternative selected in the bid proposal was the support method consisting of steel ribs and wood lagging for 2263 meters (7425 feet) of tunnel and steel liner plates for the remaining section. Shaft supports, by specification, were designed to be steel liner plate with steel ribs varying in size from 4.27 meters to 6.10 meters (14 foot O.D. to 20 foot O.D. ).

Jan 1, 1983

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By Susanne Pignolet-Brandom

Flash smelting products of a copper sulfide concentrate collected at successive levels in an experimental reactor have been studied by reflected light microscopy, scanning electron microscope - energy dispersive analysis and electron nicroprobe analysis. Chalcopyrite, intermediate solid solution, bornite, chalcocite, metallic copper, magnetite, iron-copper spinel, pyrrhotite, hematite, delafossite and cuprite have been identified in the product samples. The detailed reflected light microscopy study of these phases and their abundance in the samples has resulted in the identification of the series of reactions during flash smelting.

Jan 1, 1985

By W. Joseph Schlitt

The use of plate and frame filter presses for dewatering cement copper at Kennecott' s Bingham Canyon precipitation plant is described. The dewatering process begins by periodically flushing a dilute copper slurry from cone precipitators to a rake thickener. The thickener underflows intermittently to an agitated surge tank which feeds the filter presses with a relatively constant slurry containing 10 to 20% solids. The presses operate with a three-stage cycle; loading, air blowing and discharging. Exothermic reactions occur during the air blow which cause actual drying as well as promoting dewatering via simple filtration. At the completion of the air blow, the presses are discharged onto a conveyor belt which transfers material to the load-out building for shipment to the smelter. An extended investigation was undertaken to relate moisture content in the filter cake to maximum press temperature, acidification of press feed, percent solids in the feed, and percent insol in the copper. Of these, press tempera¬ture and feed pH (3. 5 to 1. 0) have the greatest impact on drying. Because the discharged filter cake is hot and continues to undergo exothermic oxidation, significant drying occurs during subsequent handling so that a product containing 8 to 14% moisture is delivered to the smelter.

Jan 1, 1977

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979

By D. S. Dick

Over the last few years, new methods to characterize the flow properties of bulk solids have been developed. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field conditions. In addition, the effect of large particles on a material's flow properties (cohesive strength, bulk density, wall friction) can be determined as well as the effects of various additives such as Freeze Conditioning Agents. New developments have also taken place in terms of devices to improve the reliability of solids flow. Much attention has been paid to finding ways to provide a mass flow pattern with relatively shallow hopper walls through the use of inserts. Such devices can also provide reliable in-bin gravity blending of bulk solids and/or completely non-segregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. Many of these developments have direct application in the mining and minerals processing industries. Examples of each will be highlighted.

Jan 1, 1988

By D. W. Cooper

The AMAX of Canada Limited Kitsault mine is located approximately 150 kilometers, by air, north of Prince Rupert, British Columbia at the head end of A1 ice Arm, just east of the southern tip of the Alaskan Panhandle. It is presently only accessible by sea or air, although a road is being constructed by the company which will provide access to Terrace, a commercial centre with a population of about 15,000. The topography is typically coastal mountainous with peaks rising to 2,100 meters around the head end of the inlet. The concentrator is at an elevation of 515 meters with the mine at 630 meters. This open pit molybdenum mine was previously operated between 1968 and 1972 by British Columbia Molybdenum Limited, a subsidiary of Kennecott Copper Corporation. AMAX of Canada Limited has spent $194 million to refurbish and expand this operation.

Jan 1, 1982

By David P. Kimball, Dalva L. Moellenberg

On May 21, 1990, EPA released its Strawman II draft program for mining wastes. It proposes to expand RCRA regulation of mining operations to include materials other than wastes. Strawman I1 would establish strict standards for the states to follow, rather than technical guidance. It proposes to establish performance standards; design criteria; monitoring requirements; and corrective action, closure, post-closure, and financial assurance requirements. It suggests "pollution prevention" concepts for mining operations. This paper explores the Strawman II proposals, particularly the technical criteria, and addresses several of the important concerns raised by industry.

Jan 1, 1991

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acidinsoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Nov 1, 2011

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acid-insoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Jan 1, 2011

By J. L. Young

The McLaughlin Mill started operating in January, 1985. For the first eighteen (18) months start-up, initial operation, and circuit debottlenecking have been done. The mill was designed to recover gold from a refractory ore requiring acid autoclaving pretreatment. This paper discusses the problem associated with bringing this complex hydro-metallurgical plant to consistently achieve design tonnages. Also, briefly described are the mill flowsheet, training program, permitting, and process and project development.

Jan 1, 1987