Search Documents

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By Jian Zhou, Shuai Huang, Wenqin Xi, Kun Du

The deep oceans harbor a wide variety of mineral resources that are characterized by their abundance and high quality. Nations worldwide are actively pursuing the exploration and extraction of these resources. This paper provides a concise overview of the mineral resources found in the deep sea, highlighting the challenges associated with their exploitation. Furthermore, it presents a comprehensive analysis of the historical development of deep-sea mining technology and equipment, offering valuable insights into this field. By examining the current issues and obstacles faced in deep-sea mineral extraction, this study concludes that the future of deep-sea mining lies in the direction of automation, intelligence, and standardization. Additionally, it identifies the key technological advancements that need to be achieved in order to overcome the challenges associated with deep-sea mining.

Jan 5, 2024

By W. G. Pariseau

"The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to the start of mining in the south barrier pillar. Subsequent loss of ground control in August 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterward three rescue team members. A U.S. Mine Safety and Health Administration (MSHA)report describes the events in detail (MSHA, 2008).An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools and selecting the right tool for the job is essential. In this regard, minimum program requirements include capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses.The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two-dimensional finite element analysis indicated pillar safety was by no means assured (MSHA, 2008; Pariseau, 2008; Pariseau, 2011). Geometry of barrier pillar mining is limited in two dimensions for example, crosscuts are not seen in vertical cross sections. While three-dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three dimensions. This technique involves a dual node - dual mesh concept. Both have been used separately in much earlier work, but are only now used in combination. It is possible to have an estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale (Pariseau, 2014). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2014

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

By Borje Bjorkvall

At LKAB's plants in Lappland, Sweden, sintered pellets are manu-factured according to three different industrial processes, viz. shaft furnace at Malmberget, straight-grate at Kiruna and grate-kiln at Svappavaara. At present the total annual capacity amounts to 4.7 million tons. However, since it has been decided to erect a new straight-grate plant (2.5 million tons) at Malmberget, and because of the decision to extend and rebuild the existing plants, it is estimated that the annual capacity will be increased to somewhat over 8 million tons by 1973. The great majority of the pellets produced is exported. They are thus reloaded several times and generally speaking roughly handled, resulting in larger or smaller product losses on arrival at the point of use. It is there-fore of great economical interest to have a good control over the transport strength of the pellets by appropriate quality testing at the point of production. In addition to good transport strength, further demands are ob-viously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of in addition to good transport strength, further demands are obviously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of

Jan 1, 1972

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

This study investigates the changes in seismic velocity of rockmass before and after three major seismic events to determine any potential identifiable precursory velocity changes associated with these events. Induced stress measurement is one of the challenging tasks in deep underground mining, with extreme impacts on the safety and stability of the mine. This study used p-wave passive seismic tomography to image the velocity redistribution within a rockmass, which can indicate induced stress level changes in the rockmass and detect the velocity changes that might precede a major seismic event or a rockburst. The ultimate goal of this research focus is to develop another tool for the deep-mining community that will help to increase safety and efficiency. For this purpose, the hypothesis of conventional mechanics, which implies induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs, is evaluated. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring; however, the p-wave velocity did increase in the closest “zone center” for two of the three events. 

By Meyer Klein

Decision theory is the formal theory of the logic of decisions in view of the decision maker's objectives, preferences, I beliefs, and available information, It usually deals with weighty economic problems involving irrevocable (or costly to reverse) decisions. Capital investment planning problems constitute an instance par excellence for application of the decision theory concepts. Decision theory as it is presently conceived has evolved in recent years. At first it concentrated on decisions in the face of total lack of information and on games with intelligent adversaries. The results of these efforts proved theoretically interesting, but practically of little applicability. In the last few years, stress has shifted to the introduction of subjective probabilities and preferences, and the results have been eminently successful in applications both in government and with- in business firms in the resolution of complex problems.

Jan 1, 1970

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercapto silanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1990

By Lawrence A. Engel

The idea of using apron feeders for in directly feeding crushers is not a new one, it has been used for many years. To the best of our knowledge, the first apron feeder was used for bulk material handling in 1893. Since that time many design innovations have been introduced, with perhaps the most effective one being, the application of crawler tractor components in the feeder construction. This design was first introduced to the mining industry in 1954 by, national iron company. These feeders were used in the handling of run-of-mine iron ore on the Minnesota iron range, at the rate of 1,000 ltph. The material was fed over a grizzly to a jaw type of crusher. The crusher output was also handled by an apron feeder. Today, the apron feeder is being used in hard rock surface mine operations feeding crushers at rates of 5,500 ltph and over.

Jan 1, 1983

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By Evan Just

?We are certain there is need for research in every phase of mining." This statement by R. M. Crump of the Jones and Laughlin Steel Company (047) paraphrases opinion widespread among mining people. It is undoubtedly true. In preparation for this presentation, 193 organizations were asked to describe their mining research efforts. 60% responded, The meaning of "research" was taken in several different ways. The continual efforts of progressive companies to improve themselves were reported as research. We will call this and any effort to solve specific and immediate problems "practical research". The continuing investigation of subjects of long range interest will be called "basic research".

Jan 1, 1961

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul-road conditions can have a positive impact on mine operations, resulting in heightened safety, productivity gains, longer tire life and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain Mine, monthly site severity studies, ad hoc inspections by frontline supervisors or operator feedback reporting are used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By Paul Lynch

"Since being reported to the 2012 UMI in Shanghai, the Cook Islands has been steadily developing for the commencement of it Seabed Minerals sector in its large Exclusive Economic Zone which contain a vast and unique Manganese Nodule resource, estimated at 10 billion tonnes1. At the 2013 UMI in Brazil, it was reported that the Seabed Minerals Act had commenced and all the necessary complex Technical aspects of this developmental work was being undertaken. At the 2014 UMI in Portugal, full details of the final developments leading to the opening of the Tender of Exploration Blocks in the Cook Islands EEZ will be presented in a brief but comprehensive method, using Poster displays, Powerpoint and active Website interaction. This will show the drafted Regulations, prepared on best international standards, to address both Licencing and Environmental requirements, to give clarity and security to the Resources Owner, industry and stakeholders. This work in being coordinated by the Cook Islands Seabed Minerals Authority, with the valuable collaboration of many international, regional and national stakeholders, including the Cook Islands NGOs, Marine Resources, Marine Park and National Environment Service."

Sep 1, 2014

By Baolin Qu, Jingxin Wang, Cuncang Xu, Bing Wu, Mingyu Zhong

With the development of the coal mine regulation regime, the situation of coal mine safety production in China has continued to improve. However, coal mine accidents have not been fundamentally eliminated; constantly learning from historical accidents can make mining work safer. Therefore, to better understand the coal mine accident characteristics, this study analyzes the tendency of coal mine safety accidents from multiple perspectives, among which all accidents after the establishment of the State Administration of Coal Mine Safety in 1999 are the top priority. The results show that strict national policy, technological progress, and reasonable coal prices are conducive to the safe development of mines. On the contrary, high-intensity centralized production will lead to frequent accidents in the peak season of coal production. In addition, the type of coal mine ownership will have an indirect impact on the occurrence of coal mine accidents. The research results not only play a positive role in the prevention and control of coal mine accidents in China but also have reference meanings for the safety production of coal mines in other countries in the world.

Dec 28, 2022

By AMAN SONI, JONATHAN G. BAGGETT, Nino Ripepi, JUAN J. MONSALVE, Richard Bishop

Underground stone mines are vulnerable to karst void formations due to the erosion of carbonate rocks by groundwater flow. The voids or cavities may lead to hazards including ground collapse and sudden outflow of clay-rock sediments during the development of the mine. This study evaluates the effect of karst voids on the strength of pillars in an underground room-and-pillar limestone mine. Ground-penetrating radar (GPR) surveys were interpreted to map the void boundaries inside a karst-affected pillar. A combination of LiDAR scanning and virtual discontinuity mapping is used to formulate the discrete fracture network (DFN). Discrete element modeling (DEM) helps simulate the effect of karsts and discontinuities in the pillar models with varying stress. It is observed that the cavities may lead to a significant reduction in pillar strength. Apart from posing a hazard to miners and machinery, any advance into these cavities may disrupt mine operations. This research serves as an initial step toward understanding the importance of pillar design in underground stone mines affected by karst voids to prevent local instability or pillar failures.

Sep 1, 2022

By J. O. Stephens

During the late 1940's and early 1950?s, the Westinghouse Combustion Turbine Division built and demonstrated a residual oil-burning locomotive on six eastern railroads. Plans were made to convert to burning pulverized coal, and a single combustor was operated at a full-pressure condition in the laboratory for about two years. During the mid-1960's to mid-1970's, there was considerable interest in coal-burning MHD and a combustor was developed which would also be applicable to combustion turbines. In the early 19801s, the BCR National Laboratory (BCRNL) became affiliated with the University of Pittsburgh, and a program was begun, supported by the Stare of Pennsylvania, to develop an all-purpose combustor for use with industrial and utility boilers and eventually with combustion turbines. In this paper, we review the work of almost 40 years, indicate our present position, and propose steps to be taken leading to efficient and environmentally acceptable power generation from coal, and specifically to coal-burning locomotives.

Jan 1, 1986

By R. A. Meyr, K. A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by the U.S.Congress. The U.S. Mining Safety and Health Administration subsequently released the Final Rule on Refuge Alternatives for Underground Coal Mines, which required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. The following paper documents the research that was performed on a structural wall to be used in conjunction with a breathable air system to create a refuge alternative. A 103.4-kPa (15-psi) safe haven polycarbonate wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics. The successful safe haven wall design was modeled for an actual underground coal mine environment using the explicit finite difference formulation program FLAC3D to determine the responses of the wall and surrounding strata within a mine. A full-scale design was fabricated and installed in an underground coal mine to determine any construction constraints and as a final step in proof of concept for the safe haven wall design. This paper is meant to introduce the reader to a new wall concept to be used in conjunction with current technology.

Jan 1, 2013

By David Hatem, Michael Vitale, Joseph Gildner, Michael Roach, Fred Dunham

Dispute Review/Resolution Boards (DRB’s) are a highly successful dispute avoidance and resolution tool. In a joint effort between the UCA of SME and the Dispute Resolution Board Foundation (DRBF), the authors embarked on an informal assessment of the state of the DRB practice in the tunnel industry from the point of view of the Contractor, Owner, DRB Practitioner, and Attorney. The results of this assessment were presented in a panel discussion at the Rapid Excavation and Tunneling Conference (RETC) in June of 2021. This paper presents the results of that session with recommendations for further industry discussion and implementation

Dec 1, 2022