Search Documents

By R. L. Godfrey

The Custom Coals advanced coal cleaning plant will be designed with a unique blending of existing and new processes to produce two types of compliance coals: Carefree Coal? and Self-Scrubbing Coal?. Carefree Coal will be produced by cleaning the coal in a proprietary dense media cyclone circuit utilizing fine magnetite to remove up to 90 percent of the pyritic sulfur and correspondingly greatly reduce the ash. While may utilities can achieve full S02 reduction compliance with Carefree Coal, others face higher sulfur reduction requirements due to the higher sulfur content of their existing fuel supplies. For these circumstances, a patented Self-Scrubbing Coal will be produced by taking Carefree Coal and pelletizing limestone-based additives with the finest fraction of the clean coal. These technologies will enable over 150 billion tons of non-compliance U.S. coal reserves to meet compliance requirements.

Jan 1, 1995

By M. Guney, A. R. Bell

In Mindola mine on the Zambian Copperbelt, there is a plan to extend the current production level of 1.2-1.5 km (3,900-4,900 ft) with five additional production levels. Research work indicated that the present total heat output of 38.6 MW will inevitably increase to 63.2 MW in 25 years. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 33.8/40.2°C (93/104°F) and 35.3142.10C (95/108°F) respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9, 000 MW.

Jan 3, 1984

By Feridon Ghadimi, Saeed Mojeddifar, Massume Khavari

Separation of geochemical anomalies from background is an important and essential issue in the exploration of mineral deposits. Statistical methods are used to separation of anomaly from background. Fractal/multifractal and singularity methods are very suitable for the separation of weak anomalies. For interpolation, various methods could be used such as most distance-weighting methods, kriging, spline interpolation, interpolating polynomials, and finite difference methods. This paper addressed application of multifractal techniques together with finite difference procedure to detect the anomalous regions. Fractal models such as concentration–area, spectrum–area, and singularity index model were selected to identify Pb–Zn anomalies. In this research, 170 samples from 33 boreholes were taken in the Haft-Savaran area and analyzed for determination of Pb–Zn anomaly. Singularity method was a suitable method for separating Pb and Zn anomalies. Also, the results showed that the geochemical anomaly has occurred along NE–SW trend and is consistent with the sulfide mineralization process and the faults of the region.

May 18, 2020

By D. A. Fenton

The reliability of large diameter, high horsepower ball mill is paramount when large production and minimum downtime is required. The 17 ft. x 56 ft. double compartment ball mill at St. Lawrence Cement Company has the first gearless drive built in North America and has the world's largest hydrodynamic bearings currently built and running. The machine has seen three years operation and has met its specifications. The mill was designed by Aerofall Mills Limited and the gearless drive built and designed by the Canadian General Electric Company. This paper discusses the operation of the first North American installation of a gearless drive ball mill from the mechanical, electrical and process aspects.

Jan 1, 1977

By E. Stolarski

The circulating fluid bed (CFB) technology can proudly point to its history of more than a quarter of a century of commercial operations. Over 80 CFB units operate in aluminum calcining, coal combustion and gold roasting. This paper describes the invention of the circulating fluid bed and chronicles its development and evolution from calcining through coal combustion to gold roasting. It presents performance data of Lurgi's CFB units in operation and highlights the six gold roasting plants currently operating throughout the world.

Jan 1, 1998

By Jr. Goller

You and I can visit cement plants, inspect the various rotary kiln systems and find some equipment or some burning techniques that waste energy--fuel and power. After we have made such a visit and studied a few ideas, we could recommend ways to eliminate much of this waste. Probably every idea would cost money to bring into action. For our discussion, let us arbitrarily set an upper limit of $1,000,000 on the recommendations that we are allowed to make. Call these "low-cost" or "short-term" measures. They are improvements that do not require more than say, three months to complete; they do not require a major revision to the process. Other recommendations are "high-cost" or "long-term"; they are outside the scope of this discussion. Some of our "low-cost" recommendations would offer a satisfactory return on the money that they cost; the remainder would not. Now, is there some way that we can rather quickly pick out the "low-cost" measures that will show a satisfactory return and spend our time making these improvements first? Can we separate these items from those where the return is less likely to be good? I feel that we can pick some of these items quickly if we have a kiln system that has consistently non-uniform day-to-day operation. If the operation is uniform we probably cannot pick them quickly.

Jan 1, 1977

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By Erika Moonin, Jim Nickerson, Marcus Jensen

"This paper will explain how the Contractor and Owner avoided a contractual dispute involving characterization, impacts, and final remedy for challenging ground conditions encountered during drill and blast excavation of the starter tunnel required for launch of the tunnel boring machine (TBM). During excavation more than 600 feet underground, the Contractor encountered a large complex fault zone subject to more than 14 bar of water pressure. Successive ground inflows from the fault complex over a six-month period presented significant technical and partnership challenges for the team and ultimately delayed the project by nearly one year. This paper will discuss how the Contractor, Owner, and their respective consultants worked together to address these challenges, make decisions, and ultimately move the project to successful completion. PROJECT BACKGROUND AND NEED Seven states of the western United States of America rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River basin, including the Rocky Mountains, the Wind River Mountains, and the Uinta Mountains. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. During the 1980s and 1990s, snowfall was relatively abundant and Colorado River flows were high on average. Beginning in the year 2000 and continuing to the present day, snowfall has been well below documented historical averages and Colorado River flows have diminished. In fact, a trend toward diminishing flows is evident during the period of the historical record. This variability in Colorado River flows and the trend to lower flows is represented in the following Figure 1."

Jan 1, 2016

By Jr. Winters

The United States continues to be the largest producer and consumer of copper in the world. Table 1 on the following page shows several production statistics for 1974, the most recent year which the non-communist world copper industry might consider a good year, and for 1976 and 1977. In 1974 an estimated 24 percent of the non-communist world's newly mined copper was mined in the United States, and. 87 to 89 percent of that was from the western porphyry coppers. In 1976 U. S. new mine production was down to 22 percent of the non-communist world's newly mined copper, and the percentage of U. S. new mine production supplied by the porphyry coppers had risen to 89 to 91 percent. In 1977 the statistics remained the same as in 1976. U. S. porphyry copper production represented about 65 percent of U. S. refined copper consumption in 1974, rose to 75 percent in 1976, and dropped back to 61 percent in 1977 as imports of foreign copper into the United States began to swell.

Jan 1, 1978

By Robert W. Row

Advanced physical coal cleaning processes that are now under development may remove significantly greater fractions of pyritic sulfur and ash than do commercial coal cleaning processes at comparable heating value recoveries. These processes may be useful for reducing sulfur dioxide emissions from electric utilities and other emission sources. However, little work has been done to determine their applicability to any major coal market. The northeastern states of the United States are interested in burning more coal, but with further sulfur dioxide emission restrictions. Their nearest coal sources are relatively high sulfur Northern Appalachian coals. The project discussed in this paper, which is scheduled to be completed in June 1985, has the objective of technically and economically evaluating various coal supply scenarios involving five selected advanced physical coal cleaning processes; and comparing the economics of them with alternative fuel supply options open to the northeastern users.

Jan 1, 1985

By Miguel Angel Ibarra

This paper describes the results of a digital computer simulation study in which the impact of the proposed truck dispatching on the overall mine productivity was investigated for an operating open pit mine. In the study, the existing operation was first simulated for a one-month period, using both the actual time study data and the computed cycle times. By adjusting certain input parameters to the simulation program, the actual one month production was first duplicated through simulation. Afterwards, the operation was again simulated in a dispatch mode. Comparison of simulation results under the dispatch mode, with the initial base case simulation results, showed a definite improvement in overall productivity with dispatching; i.e., approximately 10% gain for the operation. As expected, the results also showed that the extent of possible improvement did vary with the particular pit configuration being investigated.

Jan 1, 1980

By Harold J. Schock

This paper describes an experimental method for the monitoring of diesel-generated exhaust gas pollutants in a dead-ended drift for the purpose of assessing the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 105 ft. (32.0 mf long and slightly downsloping, with an average height and width of 8 ft. (2.4 m) and 28 ft. (8.5 m1 , respectively. The data were gathered for assessing these ventilation methods and for gathering data to support a computer model of the dispersion and mixing processes. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generated pollutants. Induction ventilation appeared to be the least effective of the three methods examined. A comparison was also made between personal monitoring and area monitoring. Results of this analysis showed that in regions of high concentration gradients, it was not possible to get good agreement between point sampling and personal monitoring. In well-mixed areas, good agreement between the two methods of monitoring was obtained.

Jan 1, 1980

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models could be used potentially to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1992

On Feb. 16, 2012, the Polish coal mining company Lubelski Wegiel Bogdanka S.A. set the world record for daily production from a plow-equipped longwall, with an output of 24.4 kt (26,900 st) of coal from a single face. The company commissioned the first Cat longwall system at its Bogdanka Mine, near Lublin in eastern Poland, in March 2010 and within six months had raised the bar to nearly 17 kt/d (18,700 stpd) of cut coal. Since then, Bogdanka has continued to increase its daily output with a plow face that began mining in the new 7/VII/385 panel last October, taking the world record to new levels. In addition to the record output achievement, the plow face advanced more than 27 m (89 ft) at a 1.63-m- (5.3-ft-) cutting height. ?We thought this achievement would be impossible for any shearer in seam heights as low as this,? said Zbigniew Stopa, vice president of Bogdanka.

Jan 1, 2012

By David Cronan

"Most of the recent renewed interest in manganese nodule mining has been focused in the Clarion-Clipperton Zone (CCZ) in the NE tropical Pacific where nodules are rich in Mn, Ni and Cu. However, equally interesting, but compositionally different, nodules occur in the tropical central South Pacific (CSP). The CC Zone deposits lie in the International Seabed Area whereas those in the South Pacific lie mainly in the Exclusive Economic Zones of Island States, principally the Cook Islands and Kiribati. The CSP nodules should not be regarded as an alternative resource to CCZ nodules, as they are enriched in different elements. Rather, the CCZ nodules should be thought of as a source of one group of metals (Mn, Ni and Cu) and the CSP nodules the source of another group (see below), mutually complementing each other and to be mined in parallel for their different metals.Manganese nodule mining in the South Pacific has been mooted since the 1970s. However, new data on manganese nodule composition and abundance there have recently appeared. Also, a recently developed interest in 'rare', 'green' and 'technology' elements has necessitated a re-examination of old South Pacific nodule data for information on these elements (previously thought to be economically unimportant), and the re-analysis of the deposits to obtain new data on them. Additionally, current and possibly future applications to the UN to extend island 'continental shelf' areas necessitates an appraisal of the manganese nodules in these areas. These developments have prompted recent work that has helped to refine our understanding of the distribution and abundance of metals of traditional interest in South Pacific nodules, namely Mn, Co, Ni and Cu, but has also drawn attention to other elements of possible economic interest including titanium (Ti), vanadium (V) and the rare earth elements (REE)."

Sep 1, 2014

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By J. R. Aggson

In an effort to minimize cutter roof failures in longwall development entries of a West Virginia coal mine, a three-entry system was developed with the center entry arched into the strata above the coal seam. The purpose of the arched entry was to modify the horizontal stress envelope associated with the three-entry system and improve roof conditions in the adjacent outside entries. Contrary to the predictions of elastic analyses, the presence of the arched entry improved roof conditions by eliminating cutter roof failures in the outside entries. In-situ stress determinations and numerical modeling techniques were employed to quantify the impact of the arch and investigate the mechanism of stress relief associated with the arched entry. Stress determinations and underground observations indicated that the roofs of the outside entries were within the zone of stress relief generated by the arch, and that failure or movement along bedding plane discontinuities played a major role in the formation of the stress relieved zone. The numerical model incorporated horizontal joints to simulate bedding plane discontinuities. The properties of the joints were adjusted until roof stresses predicted by the model were in agreement with measured stress profiles. This process resulted in a calibrated analytical tool that could be used to evaluate alternate mining geometries.

Jan 1, 1988

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990