Search Documents

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By Marcel F. DeGuire

Pilot plant operations are described for the treatment of manganiferous zinc concentrates from the Gamsberg ore deposit in South Africa via conventional electrolytic zinc processing. Two methods were employed for the control of excess manganese ions in the pilot plant electrolyte involving (1) chemical oxidation and (2) anodic oxidation. The chemical oxidation method for manganese control was very successful. It also was found that the addition of manganese dioxide ore was not required for oxidation of ferrous iron during the neutral leach or jarosite precipitation steps. A new method (JAR process) for iron removal also was tested in the pilot plant.

Jan 1, 1978

By A. R. Hollbach

This paper presents a succinct overview of the Canadian coal situation. The topics treated specifically are: the rates of growth of coal supply and demand; the relationship between the coal and electricity generation industries which form its dominant market; the unique impact of nuclear generation on coal demand in Canada; and finally, a view of the developing technologies which will create opportunities for growth in the coal industry of the future. Resources The most important element of coal supply is the resource. The disposition of Canada's coal resources has a marked effect on their utilization, since industry in Canada has not generally developed around coal-fields. The distance from the major industrial centres of Ontario and Quebec to the major region of coal supply in Alberta and British Columbia has crested an economic barrier to the expansion of the use of domestic coal.

Jan 1, 1985

By J. Kretschmann, H. Mischo, O. Drusche, S. Krause

Mining is and will be inevitable in spite of the increasing implementation of circular strategies. The energy transition and population growth will boost the demand for critical raw materials. It is the opportunity for miners to reinvent their business models. Generating attractive new business cases with sustainability-oriented innovations meets investor and stakeholder expectations from the beginning. This contribution guides managers on their pathway towards sustainable success. Contextual sustainable business model patterns will be presented that can be adjusted individually, regardless of actor’s size. It will also point out, how sustainable value creation can be measured on business model level.

Feb 1, 2023

By Donald G. Rogich

The concept of initiating a large action-oriented contract, directed toward inherently safe mining systems, was conceived by the U. S. Bureau of Mines in January 1970. At that time we were in the process of establishing research contracts and grants, about 100 of which were let in FY 71 to deal individually with fairly specific technological areas. These projects in the aggregate covered a wide spectrum of health and safety problems. What appeared to be necessary was the creation of a project or program that would provide a focal point for the demonstration of many of the results of this research and also in the action sense culminate with working hardware and systems that could be tested and demonstrated over a fairly long teen. The concept of working demonstrable systems, rather than just a conceptual study, was, felt to be necessary for two significant reasons. In the development of any new system, the translation from concept to working hardware is usually a costly and time consuming process which acts as a deterrent to implementation. Secondly, many decisions in the mining community to change equipment or systems ,are based on first hand observation of the new system, in operational practice, an attitude which is certainly understandable in view of the high capital costs of equipment. The decision was made to procure a single R&D contract which would be aimed at developing underground coal mining systems which

Jan 1, 1972

By Dongxu Jia, Chen Cao, Shuangwen Ma, Jun Han, Huibin Ma

Coal bump, or coal burst, is one of the catastrophic disasters in underground coalmine. Among them, approximate 80% of recorded destructive burst events were occurred in mining roadway. The bump panel is often formed by hard coal seam and hard main roof; however, the cause and course of the bump events are not understood yet. This study provides a fundamental theory for the causality and progress of a coal bump event occurred in longwall roadway. Considering hard roof condition commonly existed in bump panels, we think that the abutment pressure induced by suspended roof behind the working face is the trigger of a coal bump event occurred in the roadway. Once high abutment pressure is concentrated on the hard coal seam around the working face, the roof and the coal around the working face form a seesaw-like structure, which leads the roof in front of the working face moving upwards. The movement of roof uplifting in front of the working face is a well evidenced phenomenon in practice, namely, roof rebounding, which causes unloading of the normal stress on the roof-coal interface around the roadway. A rib coal block bump mechanical model has been developed to establish the critical equilibrium equation of the coal block. Result shows that, the force source of coal bump is the horizontal ground stress perpendicular to the rib surface; and the slippage of the coal block is caused by the unloading of the normal stress acting on the roof-coal interface. Based on the causality and consequence theory of coal bump developed in the paper, several new prediction and prevention measures have been developed, including roadway design and in-tunnel reinforcing methods. The commonly used prevention measures in present have also been discussed. This paper presents a comprehensive explanation of coal bumps occurred in longwall roadways, from abutment pressure at working face forming seesaw structure to roof rebounding leading slippage of the rib coal mass into roadway, which provides a fundamental theory for coal bump causality mechanism and prediction and prevention technology.

Apr 26, 2022

By Kevin Andrews, SETAREH GHAYCHI AFROUZ

Ground control analysis and groundwater inflow assessments for underground coal mines require in-depth field investigations including, but not limited to, geological and geotechnical core logging, downhole geophysical logging, laboratory rock strength testing, and packer (Lugeon) testing. Field and laboratory data collection are time consuming and expensive, and an initial understanding of the expected trends among various geotechnical and hydrogeological parameters can assist with the planning and optimization of geotechnical characterization studies and grouting plans. In this study, a comprehensive database is analyzed, comprised of important rock mass characteristics (hydraulic conductivity, rock quality designation (RQD), and lithology) for coal-bearing rocks in the Central Appalachian Basin. Statistical analysis of the data is completed to establish an enhanced understanding of geotechnical and hydrogeological conditions expected to be encountered as underground coal mining passes near and beneath streams and rivers. The results of the study provide valuable reference material for the coal mining industry for completion of shaft installations, mine stream crossings, environmental assessments, and grouting and mine dewatering designs.

Jul 1, 2023

By D. R. Lanners

Samples of the same coal measure overburden spoil were obtained from three different mine sites. Site A used a 27-m3 tub-mounted dragline, Site S used a front-end loader and truck combination, and Site C used a 6-m3 crawler-mounted dragline. The spoils were analyzed in the laboratory for the strength parameters using drained triaxial tests conducted on 150-mm diameter specimens. Regression analysis was utilized to determine the appropriate failure criterion for the strength data from each site. Spoil obtained from Site S yielded higher shear strengths than Sites A and C.

Jan 1, 1993

By Kwame Awuah-Ofei, Sisi Que, Shaochun Yuan, Yumin Wang, Ziwei Ding

This research sought to facilitate improved stakeholder analysis in mining by providing further insights into the preferences of local community members using discrete choice theory. While recent research has demonstrated the usefulness of discrete choice theory in mining stakeholder analysis, no previous work has examined which discrete choice model (DCM) is most suitable. This paper provides a research note on a case study in a mining community that was performed to compare three DCMs. After a thorough examination of the benefits and deficiencies of all models, this study concludes that the conditional logit model stratified by questions is the most useful DCM for mining stakeholder analysis. The recommendation is based on the usefulness and accuracy (ability to match the survey data) of this model.

Jul 25, 2022

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By K. C. Ko, M. D. Bunnell

The studied coal mi1e is an underground coal mine located in the northern Wasatch Plateau of central Utah (Figure 1) . Since operation began in 1981, in situ stress conditions have been encountered which differ from the assumed conditions utilized during early mine design efforts. Geologic structures also varied somewhat from those projected during initial geologic interpretations of the area. The encountered geologic conditions combined with the unusual stress conditions prompted a combined study of in situ stress and stress-related geologic structures. The study was conducted in two phases, with phase 1 consisting of detailed underground mapping and analysis of stress-related geologic structures to determine stress orientations from which they originated; and phase 2, consisting of over- coring two sites within the mine to determine present in situ stress orientations and magnitudes. GEOLOGIC ANALYSIS Three types of geologic structures have been encountered in the mine that act as indicators of stress orientations of the geologic past. Two of these structures, faulting, and igneous dikes, are directly measurable in the mine. A third type of structure, photolineation, was detected through remote sensing methods and shoe god correlation to roof conditions in certain areas of the mine. Faults Two major orientations of faulting have been encountered in the studied coal mine, including a system of N 80 W striking normal faults and a system of N 55 to 70 W striking oblique-slip faults. Only data collected from the oblique-slip faults were used for this study due to the fact that these faults offset the N 80 W faults wherever the two systems intersect, indicating that the N 55 to 70 W system was created by a more recent stress field. Figure 2 shows locations within the mine where data were collected from seven locations along oblique-slip faults. Data collection consisted of measurement of fault plane strike and dip, fault slickenside trend and plunge, and slip direction. The data are tabulated in Table 1. The fault data were then plotted on stereo nets to determine the stress orientations present at the td of faulting (Figure 3). The determined stress orientations are 32~0 included in Table 1. The stereo net plots show average principal stress orientations of: 1) [ ] plunge 1 degree. These data suggest that the N 55 to 70 W oblique-slip faults were produced by a nearly

Jan 1, 1986

By Hans E. Tausig

The economics of transporting minerals by sea in less than full cargo lots encompasses an analysis of production costs, sale and inventory calculations and a careful comparison of ocean freight costs all of which when pieced together will usually definitively indicate which of the ocean freight alternatives is the correct one for the economic factors involved. To illustrate: Let us assume that a production to be marketed yields 60,000 metric tons of copper concentrates over a twelve month period. Shipment is geographically viable through Vancouver, B.C. The production has been sold to a Japanese Smelter and the mine produces at a rate of 5,000 metric tons of concentrates per month. The copper has been sold CIF FO. The Seller has carefully investigated ocean freight rates Vancouver, B.C./Hibi, Japan and finds that he could obtain a twelve month freight contract at $15.00 per metric ton FIGS based on a loading/discharging speed of 4000/ 2000 metric tons per WWDSHEX (weather working day, Sundays and Holidays excluded) this freight rate being predicated on shipping in lots of minimum. 15,000 tons. A further freight investigation reveals that to ship at the same terms and conditions but in lots of 5,000 tons, and shipping each month (in accordance with the mine's actual production) would cost $20.00 per metric ton FIOS. The calculation that is now made is whether it is more desireable to pay a higher ocean freight by shipping in 5,000 ton lots or to pay the lower freight where here the ocean freight involves a difference of some $300,000.00.

Jan 1, 1979

By James M. Barker

No commodity agreements now exist for sulfur and a lack of reference to sulfur commodity agreements exists in the literature. Law (1975) made a passing reference to sulfur as one of a group of commodities where "there have been additional control efforts of various types." Clearly, sulfur was a candidate, at least conceptually in the past, for some form of commodity agreement and the following discussion centers on the world sulfur market of the early 1980's in this context. GENERAL THEORY OF COMMODITY AGREEMENTS The upsurge in demands for commodity agreements seen in the last decade or so stems largely from agitation by the less developed countries (LDC) for better economic treatment by more developed countries (MDC). Several economic factors, real or imagined, adversely affect the LDC's as follows (MacAvoy, 1977): 1) variable demand in MDC's causes wide fluctuations in commodity prices which hurt the economies of commodity producers, who are often LDC's although consumer economies may also benefit from more predictable prices; 2) a general decline of commodity prices relative to the price of manufactured goods which hurts commodity producers in their balance of trade while their stocks and overcapacity rise; 3) instability of LDC economies enhanced by the above factors lowers internal stability, inhibits foreign investment, and retards economic growth; and 4) a lack of self respect when dealing with developed countries o, following the OPEC lead, LDC producers want the stature related to cartel market power.

Jan 1, 1985

By Milton E. Jennings

On May 11, 1977, the SAMARCO 20-inch, 396-kilometer (246-mile) Pipeline was placed in service. This system represents the latest thinking in slurry pipeline design and is one of the main contributors to the viability of the SAMARCO Project. This paper presents the background, description and latest information on the system's operation. Special attention is given to the handling limitations of the slurry and to the unique hardware requirements.

Jan 1, 1978

By K. Oraee

Proven and probable coal reserves in Iran are estimated to be in excess of 5 Billion tons while the annual coal production is a mere 2 Million tons. Underdevelopment of the industry has proved higher production levels to be impossible, despite growing demand for energy supplies. The existences of numerous legislation are thought to have a detrimental effect on coal mining activities to the extent that some business entities have become uneconomical in many areas. This paper provides an analysis of the prevailing mining laws, policy making, legal frameworks and obstacles. It also outlines some other obstacles enshrined in the law and also highlights areas where foreign direct investment should be encouraged. The costs of lost opportunities are then estimated. The paper concludes by demonstrating that deregulations, amendments and in some cases complete abolishment of the incumbent legislations governing the coal mining industry will greatly enhance development of the industry. The analysis provided in this paper together with the results obtained, can prove useful to macro-economic policy makers both at local and national levels.

Feb 27, 2013

By Martin G. Casto

Mixer-settler extractors, among the oldest forms of extraction equipment, have been used since the beginning of this century. Over the past years, a very large number of mixer-settler devices have been designed and operated. Both batch and continuous flow mixer-settlers have been used. The continuous flow mixer-settler extractor offers a great number of advantages over other extraction equipment. The main advantage of the continuous flow mixer-settler is that it is a compact device. A large number of stages can be assembled in a relatively small area, and more stages can be added fairly easily. Many improvements have been made in the design of mixer-settlers. These improvements occurred in almost every phase of mixer-settler' operation; interface control, mixer design, intrastage pumping, interstage flow of the two liquid phases, and stage construction. It is believed that Barstow1 used one of the first continuous mixer-settler extractors. This mixer-settler had concurrent flow within each stage and countercurrent flow overall. The flow for both phases took place by gravity. The Barstow device and other early mixer-settlers had no separate interface control for each stage, therefore, "tilting" of the stages was necessary. In 1934 Holley and Mott2 designed a mixer-settler in which the heavy phase was recirculated within each stage by the use of a valve controlled central line instead of by a pump. Gordon and Zeigler3 in 1939 were among the first to use an adjustable valve to control the interface levels in a mixer-settler, making tilting of the extractor unnecessary. In 1952 Coplan et al. 4 used a modification of the Holley-Mott idea to build a highly improved mixer-settler with flat common walls, and with the

Jan 1, 1971

By K. J. Shoop

An analysis of an iron ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency in the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Experiments were divided into two groups: 1) Drop testing, which was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. 2) Wet grinding, which was further divided into laboratory tumble tests and pilot plant scale tests. Laboratory tumble tests were performed to determine the effect of temperature on the grinding of iron ore. This was done by varying the percentage of fines and percentage of metamorphic clay material added to the iron ore grinding charge. The pilot plant scale tests were conducted as a scale-up of the laboratory tumble tests and to determine the effect of temperature on slurry rheology, and how this changing rheology affected the grinding of iron ore. The combined results of drop testing and wet grinding were used to make some predictions of the performance of plant scale autogenous grinding. In drop tests the breakage characteristics of the iron ore had no noticeable change in size stabilities for dry and water saturated samples over the temperature range studied (-25°C to 25°C). The effect of frozen pore water was not observed due to the low apparent porosity of the iron ore. The addition of fines to the test charge caused a decrease in the amount of new fines produced for both the laboratory tumble tests and pilot plant scale tests. The production of fines further decreased when tests were performed at the colder temperature. The increased energy consumption at lower temperatures was dominated by rheology phenomena. The addition of metamorphic clay material to the iron ore test charge resulted in more fines being produced in the laboratory tumble tests. This was due to the metamorphic clay material grinding easier than the iron ore. This caused an increase in the amount of fines in the mill, which in turn, would prematurely slow down the grinding of iron ore because of an increase in the viscosity of the slurry.

Jan 1, 1995

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By Stuart W. Maher

A major problem in future discoveries of base metals is their "explorability". By this I mean an exploration program must be designed that assures accurate assessment of the potential for ore, but is within reasonable budgetary constraints. As we are compelled to depend more and more on non-outcropping prospects, "blind" deposits, and as drilling costs multiply, the costs of exploration increase significantly. Solutions to the problem of defining exploration targets are influenced by our conceptions of the origin and recognition o f conditions that localize ore. The maxim that "elephants should be sought in elephant country" presumes we can recognize elephant country. This paper presents a suggested origin for some mineral deposits, and their controls; particularly those termed ?Mississippi Valley type". Tennessee is used as an example of the ideas offered. Mining districts designated "Mississippi Valley type" are, and have long been, the principal sources of barite, fluorite, lead and zinc ores in the United States and elsewhere throughout the world. A large volume of literature is available describing this class of ore deposits, explaining their habitat, and invoking genetic models for them. The quality of this literature is notably uneven, some of it demonstrably erroneous, and much of it is restricted to detailed descriptions of one aspect of the problem, or to detailed descriptions of one aspect of the problem, or to a single mine, or even a single stope. If an ore deposit is thought

Jan 1, 1977