Search Documents

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By Alena Johnson

"Much of the copper being produced today uses heap leaching, where pure metal is extracted from the ore with a chemical process rather than smelting. This technique is deployed extensively in major copper producing areas including Chile, Peru and the southwestern United States.Copper ore is excavated from the ground, crushed and then spread in uniform layers on a pad. A slow trickle of sulfuric acid is distributed over the pile, where it percolates to the bottom and a collection point. The acid leaches out the copper, along with other minerals, which can be extracted chemically. This process can be used at large sites producing 100 kt/a (110,000 stpy) and greater.Production on a massive scaleProduction at heap-leach sites is continuous and can operate on an enormous scale. The ore is fed into a crusher to break down the large pieces, and then it moves into an agglomerator to capture the fines and create more uniform particles. While in the agglomerator, the ore is mixed with acid for the first time, helping it to bind the fines into larger particles and starting the leaching process. The treated ore moves by conveyors to a stacker designed to spread it uniformly on the pad.The size of the operation comes into perspective by considering a typical pad measures 1.6-km (1-mile) long and 0.8-km (0.5-miles) wide. Working day after day, the stacker creates individual piles or modules on the pad, each 122 x 61 m (400 by 200 ft) and 3 m (10 ft) deep. When one module is filled, it moves across the pad to the next, filling the area in one continuous pile. A completed row of modules spanning the width of the pad is a cell. Once the entire pad is covered, the process begins again laying down another 3-m (10-ft) layer, and it continues until the entire pad reaches its height limit which can be several hundred feet.Once a new module is completed, technicians lay a network of plastic pipes over the surface in a pattern similar to agricultural drip irrigation installations. The diluted sulfuric acid, called raffinate, is pumped through the pipes so it can be distributed over the module, allowing the acid to soak through the ore and leach out copper as it percolates to the bottom. At the same time, approximately 35 to 45 percent of the acid is consumed by dissolving the calcite carrying the metal in the process. The raffinate reaching the bottom is now characterized as pregnant-leach solution (PLS) since it carries the copper the company is seeking to recover."

Jan 10, 2018

By B. Cousins

Flotation reagents are critical to the optimum performance of flotation circuits. How a flotation reagent performs within the first few cells of a flotation train is a key indicator of how well it will perform throughout the entire circuit. A method to compare reagent performance was recently developed by Ashland Water Technologies. The procedure involves collecting a timed sample of concentrate from each cell and then measuring the volume of the settled solids. An estimate of the percentage of concentrate collected from each cell can then be mathematically determined, providing an understanding of the recovery changes in each cell. Data from trials at a coal flotation circuit are used to demonstrate the method's validity.

Feb 27, 2013

Production reporting is a natural computer application and is often one of the first applications implemented by new computer users. Automation of a manual reporting system is a good place for new computer users to gain computing experience because generation of basic reports - is fairly straightforward, and automation can often be justified easily on the basis of clerical cost savings. Computers are particularly well-suited for reporting applications which generally satisfy the criteria for effective computerization. Three characteristics must be present to effectively utilize a computerized system: 1) The potential application must be precisely definable. If an algorithm for data processing cannot be developed, data cannot be processed. 2) The operation to be performed must be repetitive. If a particular function is only going to be performed once, computerized systems development is probably not justified. 3) The volume of the data to be processed must be relatively large. If only a few items of data must be manipulated, manual methods are probably adequate. Although a computer can perform only a few functions (it can compute; it can make comparisons; it can rearrange data), it can perform these functions much faster and more accurately than a human being can. The ability to classify and reclassify data in a variety of ways and the ability to summarize data make the computer an ideal tool for production reporting. Production reports can be classified into three major categories, depending on their purpose. Reports can be used for (1) informative, (2) analytical, and (3) control purposes.

Jan 1, 1979

By G. V. Krishnan, L. Adler

A rock classification for drilling and boring is presented covering most equipment types and providing an estimation of the key parameters for operation, such as thrust and speed, and of performance such as penetration rate and bit life. Drilling and boring are significant and integral aspects of both the mining and heavy construction industries. Together these constitute over 20% of the G.N.P. Drilling and boring represent the most arduous mechanical processes performed in industry. Their misapplication quickly leads to equipment destruction, hazards, and to major delays. The classification is unified in two ways: 1) for a particular rock class several parameters can be estimated, 2) the classification integrates most excavating activities (i.e. digging, ripping and even blasting), and is derived from ground control. The rock classification provides a job property, based on fundamental and index properties, which yields quick and rough estimates of vital information. However it does not obviate the need for a more thorough analysis, and maintaining field records. BACKGROUND In order to adequately describe a drilling operation the conditions, activity, and equipment must be characterized. Of these the major independent variables are the conditions. Conditions focus on the geologic mass and also consider whether the site is surface or underground. The primary component of the geologic mass is the rock type, detailed below in Rock Characteristics. The other components

Jan 1, 1983

By I. R. Firth, D. L. Taylor

The ability to accurately model the movement of grade boundaries during a typical bench blast would be of significant benefit to mine operators. The movement of grade boundaries during the blasting process may have significant impact on grade recovery if not accounted for. The paper describes the preliminary stages of a research project which combines numerical blast models and conventional mine planning software to allow practical use of the results of a numerical blast simulation. A two dimensional bench blast is simulated using the Universal Distinct Element Code (UDEC). The results of the simulation are used to provide input to the Surpac mine planning package which can be used to generate grade control plans.

Jan 1, 2001

By J. Iannicelli

Spray drying is the principal drying method used in the production of over six million tons annually of beneficiated kaolin in Georgia. Thirty-three dryers in the Georgia Kaolin belt comprise the highest concentration of large tonnage spray dryers in the world. The steady growth of spray drying in the U.S. kaolin industry is paced by advances in design and development of large spray dryers which have led to large scale new applications in mining and related industries.

Jan 1, 1982

"When boring a tunnel, homogeneous hard rock is the exception rather than the rule. While contractors can set goals such as meters per month and performance incentives, it is also prudent to plan for difficult ground. A properly designed tunnel boring machine (TBM) can tackle fault zones, water inflows, squeezing ground, or whatever the risk may be. The alternative is not a good one: modifying the machine in the tunnel after bad ground is encountered. Not only does this result in increased downtime, but it also needlessly exposes the crew to the tunnel conditions. In the worst case scenario, the entire operation grinds to a halt.However, an accurate GBR cannot always be obtained, particularly for mountainous, high cover tunnels in remote locations. And even with a thorough GBR, unforeseen geological events can occur. What can be done in these situations? Difficult Ground Solutions (DGS) is ground investigation system with a suite of options that can be added to a shielded hard rock machine or dual-mode, Crossover machine to better enable advance when conditions are unknown or difficult conditions are anticipated.DGS consists of a set of integrated features tailored to a specific project’s geology. The main components of the system allow for ground investigation ahead of the TBM, increased monitoring and methods to keep a machine shield from becoming stuck.In fault zones and squeezing groundIf fault zones or squeezing ground are known or suspected, or if there is even a possibility of encountering them, this can greatly affect the TBM operation. Shielded machines protect the crew from the surrounding rock, and they can bore and line a tunnel efficiently, but in fault zones and converging material their shields can be their downfall. Avoiding a stuck machine is paramount to project success. DGS employs several features to avoid the problem of a machine becoming stuck. The first of these is multi-speed cutterhead drives. These drives effectively give the machine multiple modes of operation—high speed, low torque for hard rock, and low speed, high torque for difficult ground. Designing a machine with high-torque, continuous boring capabilities allows that machine’s cutterhead to restart with break-out torque in difficult ground. The net effect is that the machine can keep boring in the event of a face collapse and can bore through fault zones and running ground where the potential for cutterhead jamming exists. Going one step further, multi-speed gearboxes give the machine the ideal earth pressure balance- (EPB-) type torque if larger sections of soft ground are anticipated.Secondly, TBMs can get through squeezing ground and faults using Continuous Shield Advance. This design utilizes a stepped shield configuration — where each successive shield is slightly smaller in diameter — to avoid becoming stuck in converging ground. External shield lubrication is an added insurance against becoming stuck, using a series of radial ports that can pump Bentonite into the annular space to act as a lubricant in squeezing material.As a last effort, if a machine has already become stuck the TBM can utilize augmented, or “super” thrust. Additional thrust jacks can be added to supply an extra boost in a short stroke, generating enough force to break loose a trapped shield."

Jan 12, 2017

According to the Balandin's (1) "multiplet theory of catalysis", adsorption can occur only if atoms of the reactant molecules are congruent with surface atoms of the catalyst. Such a condition calls for certain definite geometrical relationships between the reactant molecules and the atoms at the surface of the catalyst. If such a match or geometrical 'fit' is not provided, the surface reaction will not take place. An appropriate analogy to this may be the lock and key theory that enzymes should fit a substrate just as a key fits a lock. Similar geometrical considerations in adsorption studies were made in connection with the flotation of minerals. Gaudin(2) and Gaudin and Preller (3) proposed that if the dimensions of collector ions are in registry with the mineral lattice, an ordered layer of adsorbed species is formed. They explained that the structural fit is one reason for good flotation of galena with xanthate. In another study, Bachmann (4) attributed the selective flotation of KC1 from NaCl with amine to the fact that the lattice parameter of the amine collector is closer to that of KC1. Schubert(5) investigated the flotation of various nonmetallic minerals with amine and pyridine, and related the dimensions of the collector ions with the anion distances of the mineral surface. He concluded that good flotation is obtained when the tolerance is within 20%. The geometrical theory has also been used by Groszek (6) to explain the preferential adsorption of n-paraffin onto the basal plane of graphite. The geometrical theory has thus been found useful in explaining adsorptive properties of an adsorbate relative to the substrate structure. The purpose of the present work is to examine the possibilities of a geometrical fit between sodium dodecyl sulfate and Cu(OH)2 surface, and to construct a crystallographic model of the surface compound.

Jan 1, 1974

By Siyu Song, Yanhong Wang, Guohua Gu, Linbo Huang

In this study, the effect of cations, Na+ and Mg2+, in saline water on copper flotation in the presence of calcium bentonite was investigated. It was found that as the concentration of NaCl was increased, the copper recovery initially decreased and then increased to above 99%, while the copper grade initially increased and then decreased. In contrast, as the concentration ofMgCl2 was increased, the copper recovery continuously increased, while the copper grade continuously decreased. The variation of copper recovery and grade was mainly attributed to the synergistic effect of pulp rheology and flotation solution chemistry. The underpinning mechanisms are the compressing electrical double layer and ion-exchange interaction between saline water and bentonite, which occur at the same time. Using salinewater slightly affected the pulp rheologywith a decrease in copper recovery at low NaCl concentration. Increasing the concentration of cations in saline water might even facilitate the flowing out of exchangeable cations, especially divalent cations, from the interlayer space of bentonite to the solution, resulting in the decrease of copper grade at high salt concentration.

Sep 10, 2020

By A. K. Sheik

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999

By B. K. Parekh, Z. Chen

INTRODUCTION The need for cleaning and recovery of fine (minus 28 mesh or 0.5 mm) coal fraction has increased in recent years. This results from realizing a substantial recovery of ultraclean coal from the waste stream improving overall Btu (heat) recovery, providing extra revenue for the coal industry. Also the potential of using the clean coal so obtained for making coal-water mixture which could replace oil. An additional benefit of recovery clean coal from the waste stream is reducing environmental concern of burning uncleaned coal and in waste disposal. Deashing of coal by physical beneficiation processes is limited by the degree to which ash components are liberated from coal. Conventional processes have been inefficient in terms of Btu recovery, for ultrafine coal. Chemical cleaning methods, which involves leaching of ash material from coal, have provided ultraclean coal at high Btu recoveries, are more costly than the physical cleaning methods. An advanced physical separation technique that appears to address the need discussed above is selective flocculation. This technique which has been successfully utilized in iron ore beneficiation offers the potential of processing fine and ultrafine coal to produce a clean fuel. OBJECTIVES The main objective of the present study is to investigate applicability of selective flocculation technique for recovery of clean coal product from the waste coal slurry supplied by the Peabody Coal co., from their three different coal preparation plants. It is also the objective of the program to conduct preliminary economic study of the selective flocculation process.

Jan 1, 2002

This review provides a new and comprehensive summary on studying colloidal interactions encountered in mineral processing with representative examples for critical information, which are of great scientific and practical importance. Colloidal interactions play a vital role in mineral processing, including grinding, physical separation (particularly flotation), dewatering and tailings management (Fig. 1). Despite great energy input in comminution to liberate valuables from gangues, hetero-coagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. The importance of colloidal interactions is becoming increasingly significant as we process ever more finely disseminated low-grade ores as a result of inevitable depletion of high-grade ore deposits. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. 

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By S. Finsterle, R. C. Trautz

We performed numerical modeling studies to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is a key factor affecting the performance of a nuclear waste repository such as the one proposed at Yucca Mountain, Nevada. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network as well as on the capillarity of individual fractures intersecting the opening. We developed a high-resolution numerical model of an unsaturated fracture network and examined the appropriateness of seepage predictions using a fracture-continuum model. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2000

By Deborah A. Peacock

"Outer space technology and exploration have reached a tipping point, so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies worldwide are on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3.The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars.How and why are the Moon and asteroids and their resources of interest to private space industry companies? Why are the Moon and asteroids viewed as a potential business venue?Geology of the Moon and asteroids — Why do we want to mine there?Space enterprises are actively working toward establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products and distribution of the products and services in space and to Earth and beyond2.Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral-rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind."

Jan 1, 2017

By Elham Najafi, Sina Ghassa, Ata Akcil, Hadi Abdollahi, Sandeep Panda, Zohreh Boroumand

The present study investigates the influence of ferrous iron (as FeSO4) and ferric iron (as Fe2 (SO4)3), and pyrite (FeS2) on the ability of bacterial leaching of a high-grade sulfide Zn–Pb ore. In this regard, shake flask experiments were carried out at 5% (w/v) pulp density of the ore sample (having 40.7% Zn and 12.4% Pb initial metal content) using a consortium of mesophilic iron and sulfur-oxidizing acidophiles. A concentration of 0.04 mol/L of ferric iron in the leaching media was found to be optimum for zinc extraction without affecting growth of the microorganisms. Under this concentration, the dissolution of Zn, Pb, Cd, and As was found to be 57%, 0.2%, 0.03%, and 9.9% in 25 days. Using ferrous iron in the media, 0.16 mol/L of Fe2+ was found to be the optimum concentration for efficient bacterial growth and metal dissolution (54.6% Zn, 0.08% Pb, 0.03% Cd, and 10.2% As) from the sample in 25 days. On the other hand, using pyrite as the source of energy for bacterial growth, an initial 12-day lag period was observed when compared to the effect of ferrous iron in the media. Under the optimum concentration (test with 0.24 mol/L iron in the form of pyrite), the dissolution of Zn, Pb, Cd, and As was found to be 39.8%, 0.1%, 0.03%, and 10% in 25 days. The surface chemistry analysis indicated formation of a sulfur layer over the particle surface that hindered reagent diffusion and affected metal recovery through bioleaching.

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials and the consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium. Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, X-ray fluorescence analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 wt.% V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples Ca carbonates also significantly contribute to the V deportment, while wuestite, lime, and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the V-bearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Oct 14, 2023

By Daniel T. Eyde

The U.S. Geological Survey (USGS) estimates world production of natural zeolites to be 2.7 Mt (3 million st) in 2013. China ranked ?rst with 2 Mt (2.2 million st), followed by the Republic of Korea at 230 kt (253,000 st) and Turkey at 50 kt (55,000 st). Japan?s production is reported to have increased as a result of zeolites, reportedly low grade local mordenites, being used to treat the low-level radioactive contaminants in the areas surrounding the damaged reactors at the Fukushima Daiichi power plant. China and other countries? high-volume, low-value construction applications, which include dimension stone, pozzolans and lightweight aggregate, are also included in production. This means the production data does not accurately indicate the quantities used in high-value added specialty applications. Consumption in the United States, according to USGS estimates, increased slightly, to an estimated 71.3 kt (78,400 st). Domestic uses for natural zeolites were, in decreasing order by tonnage, animal feed, pet litter, cement (primarily down-hole cement applications by the drilling industry), water purification, odor control, waste water cleanup, fungicide or pesticide carrier, gas absorbent, fertilizer carrier, oil absorbent, desiccant, catalyst and aquaculture. The six leading uses accounted for more than 70 percent of the domestic natural zeolite sales tonnage.

By G. F. Ayakwah

Point load strength (Is50) and slake durability (ID2) indices provide a measure of the strength and durability of rock fragments and are related to the alteration intensity and frictional resistance of the materials. Samples were collected from the rock piles, alteration scars and debris flows at the Questa mine with the purpose of examining relationships between Is50 and ID2, mineralogy, chemistry, weathering, hydrothermal alteration, and other geotechnical parameters. The Is50 from the various rock piles ranges from 0.6-8.2 MPa and the ID2 ranges from 80.9-99.5%. The Is50 and ID2 results indicate that the samples from the debris flows are stronger (average Is50= 4.0 MPa and ID2= 98.4%) than the rock-pile samples and that the alteration scar samples are weaker (average Is50 = 2.8 MPa and ID2 = 89.2%) than the rock-pile samples, but still most of these rocks are strong in terms of their Is50 and ID2. The Is50 decreases as the degree of alteration increases in some rock pile and alteration scar samples, but not in all. However, the majority of the rock fragments within the rock piles still indicate high strength, even after 25-40 years of weathering.

Jan 1, 2009