Search Documents

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

Explosives are used to mine coal. Any blast results in three size categories of products, namely over-, middle-, and under-size. Boulders can still be broken smaller in further operations after blasting. The under-size, for instance coal fines, negatively affects the mining efficiency. Their reduction ensures better returns. The paper concerns investigations aimed at reducing coal fines' generation. Inherent fractures are identified as one of source of fines. The discussion is therefore centered on establishing a relationship between the fracture occurrence, the explosive properties and the blast outputs evaluated in terms of the fines generated.

Jan 1, 1996

By Ian Farmer, Nigel Glossop, Philip Garritty

Performance of tunnel boring machines - usually expressed in terms of penetration per revolution - is determined by relations between machine thrust and torque, head diameter and rock strength. It can be shown that for a given machine power and head diameter there is only one rock strength at which the machine performs optimally. In weaker rocks the available torque limits performance and in stronger rocks, the available thrust. Performance data shows that, historically, machines have been designed to cut weaker rocks. Optimization of thrust is required to improve performance in stronger rocks.

Jan 1, 1987

By L. A. Ruth

Vision 21 is a government/industry/academia cost-shared partnership to develop the technology basis for integrated energy plants that will, early in the 21stcentury, result in the deployment of ultra-clean plants that produce electricity and “opportunity” products. Vision 21 plants will use fossil fuel feed-stocks in combination with other domestic resources, e.g., biomass, municipal waste, and petroleum coke. Opportunity products could include transportation fuels, steam, high-value chemicals, synthesis gas, and hydrogen. Performance targets for Vision 21 plants, example plant configurations, and the key technologies that will be needed are described.

Jan 1, 2000

By R. Schlüter

"The “Biohydrometallurgical Center for Strategic Elements (BHMZ)” is a cooperation of 13 departments of the Technical University Bergakademie Freiberg fostering interdisciplinary research along the whole (bio-) hydrometallurgical process chain to extract indium and germanium from sulphide ores. Research comprises methods to (i) bring the respective metal from the source material into aqueous solution and (ii) different approaches to extract pure metal or metal-containing materials from the solution. Within the BHMZ the Department of Underground Mining Methods deals with the design and implementation of an underground testing facility for bacterial in-situ stope leaching in its own “Research and Educational Mine”. The intention is to investigate innovative approaches for leaching technologies by crack initiation due to hydraulic fracturing or water pressure blasting under consideration of leaching kinetics and underground conditions. It is planned to set up two testing units comparing energy input and the metal output of conventional (blasting) as well as one of the innovative technologies. Aim of subproject is to establish an innovative and sustainable method ready for up-scaling. BACKGROUND Metals like copper and zinc mainly occur as sulphide ores in nature. Due to the insolubility of these sulphide minerals the respective metal is commonly extracted by pyrometallurgical processing methods. These methods require several steps of enrichment of concentrates such as flotation and roasting (Figure 1) under extensive energy utilization. Additionally, this arouses the emission of sulphur dioxide gas which can have a negative impact on the environment in form of acid rain, as long it is not caught by sulphuric acid facilities (Schippers et al. 2011). However, to treat the ore on the surface either open pit or underground mining operations are necessary. This implies operation steps from excavating, loading, and conveying/hauling, to dumping with the sub-processes crushing and stashing. Due to the tendency of increasing depth, more complex ores and decreasing ore grades of the mineable deposits as well as increasing energy and environmental costs these conventional mining and processing methods become in general more costly and difficult to apply. Hence, hydrometallurgical processes and especially the suitability of bioleaching as an alternative in-situ method for future mining projects should be examined. Leaching by means of microorganisms is a combination of mining and processing by converting the insoluble metal into an aqueous form. This technology is an economically beneficial and environmentally friendly alternative to pyrometallurgical processing methods especially for primary and secondary low grade ores. Mainly the extraction of copper but also of zinc and lead from sulphide ores is state-of-the-art in surface leaching operations like heap and dump leaching (Figure 1)."

Jan 1, 2015

By J. A. Procarione

Introduction Ventilation engineers have always felt somewhat uneasy when, in the normal course of their work, they are forced to consider the flow in any mine entry as "wholly rough." Under such conditions in pipes, friction factor is no longer a function of Reynolds' number. This assumption serves to simplify the problem and overcome an evident lack of information concerning the variability of K-factors. During the summer of 1985, a unique opportunity to investigate the reaction of friction factor to changing flow rates presented itself. A Utah coal mine was temporarily directing a substantial airflow through a single entry. By regulating the quantity, it would be possible to obtain a wide range of Reynolds' numbers in an entry composed of two distinct coal thicknesses. This paper describes the conducted study. The theory covering basic fluid flows in pipes that led to the questioning of constant K-factor is presented first. Experimental procedures are then described, including the use of a view camera in determining entry area and perimeter. Finally, a discussion of the observed variations in friction factor versus Reynolds' number is given. Changes of 34% and 45% in K-factor were seen in this study for the two entry heights. The implications of ignoring the relationship in this case and a call for an expanded research effort are also presented. Theory Since a gas is a fluid, the general principles of fluid mechanics are equally applicable to airflow in a mine entry as they are to the flow of water in a pipe. The Darcy equation is, therefore, equally applicable to pressure drop calculations in both situations. This famous formula was originally derived for use in circular cross sections and may be modified for any other shape by the use of hydraulic radius (defined as the area divided by the "wetted" perimeter). The Darcy equation relates the physical parameters of the pipe (diameter, length, and resistance to flow) and fluid velocity to the energy needed to create the flow. A study by Nikuradse (1933) brought to light the suspected dependency of the friction factor term in the Darcy equation upon Reynolds' number. By performing a large number of laboratory experiments, he established some basic concepts upon which other researchers built. Chief among these contributors was Colebrook (1939). Using commercial-grade pipe, he established an empirical relationship between Darcy's friction factor and Reynolds' number that is still in use today. If Colebrook's system of equations is plotted on log-log paper (as was done by Moody, 1944), the curves have some very distinct features. Of importance to the subject at hand is the relative response of friction factor to Reynolds' number at a given relative roughness. Simply stated, a pipe can appear to be either smooth or rough, depending on the flow conditions. As the Reynolds' number increases, the friction factor decreases at a decreasing rate until it becomes nearly a constant value. At this point, the flow is said to be "wholly rough." It is upon this condition that many traditional ventilation solution methods depend. For calculating pressure drops in a mine entry, Atkinson's equation is much more popular than the Darcy equation. Both of these formulas describe the same phenomenon and so have similar forms and functions. The K-factor in the Atkinson equation is equivalent to the Darcy friction factor and can be related by simply changing units, equating the pressure drops, and canceling like terms. A generalized form of this relationship is presented below as equation 1. K = yf/28,800g = [q]f/28,800 (1) where K is Atkinson's friction factor in kg/m3 (lb - min2/ft4), Y is the specific volume in Nt/m3 (lb per cu ft), p is the fluid density in kg/m3 (slugs per cu ft), g is the acceleration due to gravity (9.8 m/s2 or 32.2 fpsz), and f is Darcy's friction factor, which is unitless. The objective behind Eq. 1 is to show the strong correlation between K and f. Since these two quantities differ only by a constant (q]/28,000), the assumed independence of K-factor and Reynolds' number is suspect in light of the known response of f. Unfortunately, the formulation does not provide information concerning the actual relationship, as entry geometry likely plays a major role in the response curve. Only an indirect indication that such a relationship might exist is provided. Previous work on this subject was performed by Thomas Falkie (1958). The study involved a laboratory model composed of sections of straight, steel duct and a range of Reynolds' numbers from 15,610 to 137,200. Results from this work show a variation in friction factor with Reynolds' number in much the same way as it was found to vary in pipes. Over the range of velocities examined, a decrease of approximately 38% in K-factor was observed. This previous experience provides additional incentives to investigate the phenomenon under field conditions. Past model studies done at the University of Utah by Ozukurt (1945), Biron (1944), and Greenhalgh (1942) present similar evidence of this variability. More recently, Kharkar's (1974) study of coal mine friction factors contains similar indications that K-factor is not constant in all situations. Taken together, the data

Jan 1, 1988

By Frank Hagar, George M. L. Robinson

NTRODUCTION The Resource Conservation and Recovery Act and CERCLA (SUPERFUND), in many instances, has had an adverse economic impact on the hardrock mining industry. Over the last few years, many abandoned and active mining operations have been added to the Environmental Protection Agency (EPA) National Priority List (NPL) . When the property is placed on the NPL the operator or EPA is required to conduct extensive environmental assessments to determine if historical mining practices have degraded the existing environmental. If degradation has or will continue, the responsible party is required to implement appropriate remedial action plans. If a responsible party is not identified, the EPA implements a cleanup program. Experience has demonstrated abandoned and active mining operations are subject to RCRA, and possibly Super- fund, if the mine has not adopted appropriate hazardous waste disposal management procedures. If off-site contamination has occurred, the operator will be required to mitigate the impacts and will be required to adopt additional procedures to minimize future impacts. Since the passage of RCRA and Super- fund, many mining operators are adopting management procedures to monitor and inventory hazardous sub- stances and wastes generated, stored and disposed on site. Many operators are in a difficult position because ore, waste rock, process chemicals or other solid waste, in many instances, can be classified as hazardous waste. If the process or other solid waste is deemed to have the characteristics of a hazardous waste, the operator can inventory and adopt appropriate, in- expensive management procedures. However, if the ore or waste rock has hazardous waste characteristics, in- expensive control technologies are impossible to implement. Since existing statutes and regulations require hazardous waste control, the operator will be required to inventory, characterize and monitor all aspects of the mining operations including but not limited to exploration, mining, ore processing and waste disposal. During this process, geological, geotechnical, geochemical, waste and ore volumes, and process materials must be tracked throughout the mining process. To accomplish this task, the most cost effective method to maintain documented and accurate records, is through the implementation of an integrated database management system. The database management system can be used to model and simulate the entire mining operation and if necessary, used to predict whether the operation is in compliance with existing regulations. The developed database can also be used to operating optimize mining and disposal costs.

Jan 1, 1987

By C. S. Kucukkaragoz

An ilmenite concentrate was reduced in the solid state with carbon under argon atmosphere at temperatures between 1000oC and 1400oC. The ilmenite concentrate and 50% excess carbon were reacted to achieve the highest attainable degree of reduction at each temperature and the reaction products were subjected to a series of analytical work by optical microscopy, X-ray diffraction analysis and SEM ( EDS) analysis. The ilmenite remained unaltered at 1000oC and had a slight change in its composition at 1050oC. A secondary oxide phase containing metallic nuclei was detectable at 12% reduction at 1100oC. The reduction of TixOy took place in a sequence changing the y/x ratio from 2.0 to a value less than 1.0 at 84% reduction at 1400oC. Metallic phase consisted of Fe and C initially and started to include Ti at the later stages. Complete reduction of TixOy to metallic Ti was not possible at these temperatures.

Jan 1, 2005

By William G. Pariseau

Few departments of mining, metallurgical or petroleum engineering in the United States have critical mass. Cost per student credit hour (SCH) in departments across the country are usually the highest among engineering departments, which are the highest on campus. Almost all departments are operating at fixed costs and enrollments could easily double without incurring much additional cost. However, the cost per SCH would remain unacceptably high and the probability of doubling enrollment is nil. Declining enrollment is a more likely future. The pressure to reduce SCH from university administration is unrelenting. And it has the potential for doing serious damage to program quality when standards and requirements are lowered in attempts to maintain enrollments and increase retention.

Jan 1, 2002

By F. Warnaars

Historically, this area produced gold and silver from many well-known vein deposits, like Tayoltita, Topia, and San Jose de Gracia. Modern exploration identified three categories of deposits: 1) low grade porphyry golds in shallow level dacite porphyries; 2) batholith-related deposits; and 3) those formed in volcanic sequences of Late Cretaceous to Late Tertiary. At least four porphyry golds have been identified, of which Metates is best known. These are formed by and within daciteporphyries, associated hydrothermal breccias and sometimes within surrounding meta sediments. Their ages are from mid-Cretaceous to Early Tertiary. Precious metal deposits associated with batholiths occur as veins, contact haloes in meta sediments or volcanics, skarns, tectonic breccias, hydrothermal tourmaline breccias, dacite dikes or as disseminated or stockwork deposits such as La Fortuna.Several new gold discoveries were made in older EarlyTertiary Volcanic Sequences and in the younger Tertiary volcanics within prominent structures exceeding 3 to 5 km in lengths. Some of these are open-pittable but most have to be mined by underground methods.

Jan 1, 1999

By J. D. Bliss

The discovery that triggered the current gold rush in southeastern Peru was made in about 1975 along the Rio Madre de Dios in Madre de Dios Department (Fig. 1). About 5000 to 10,000 miners (called chichiqueros) were working in the area as of 1990. Placer mining is the principal source of revenue for people living along the Rio Inambari and west of Puerto Maldonado. As in past gold rushes, working and living condition are harsh. Supplies are expensive, and the area has poor access compared with other areas in Peru. Food, fuel and all mining supplies are trucked over dirt roads from Cuzco, a three-to-five-day trip (Fig. 1). Some material also comes from Brazil. Many placers have a similar life cycle, beginning with small-volume mining (surface or underground). At the end of this small-scale mining, the placer is exhausted or it has a sufficient volume of gravel high enough in gold grade to be worked by large-volume methods, which lead to exhaustion of the resource. The level of maturity of a placer can be determined from its gold grade. The amount of gold production from large-volume mining can be predicted, given detailed, cumulative gold-production data on placer deposits during small-scale mining (Bliss et al., 1987). Using this general model, the authors analyzed the placers in the Rio Madre de Dios area. Small-volume mining Most placer mining in the Rio Madre de Dios area is in alluvial deposits either in or bordering the major rivers. Locally, some placer mining is in terrace deposits above the rivers. All minerals (including the subsoil) in Peru belong to the state. However, a mining claim (denuncia) is easily obtained for mineral exploitation. It is separate from property ownership.

Jan 1, 1992

By G. Brooks, J. T. Ellington, M. Yensco, G. E. Mcquien, M. T. Ityokumbul

Coarse silica flotation from intermediate pebble (IP) product has been carried out a pilot plant Dual Extraction Column (DEC) at an operational phosphate mine in Central Florida. The solids feed rate ranged from 4.16 – 5.3 TPH while the amine dosages ranged from 0.32 – 0.93 lb/T. The optimum amine dosage when using recycled process water was deter-mined to be 0.6 lb/T. With a feed containing 40-45 BPL and 38-45% insol, the results show that the IP can be upgraded to 56-61 BPL and insol of 16-22% at 85-90% BPL recovery. The results show that the DEC is an effective device for flotation of coarse silica from the IP. The advantages of upgrading the IP prior blending with the pebble are presented and discussed.

Jan 1, 2004

By James K. Kindig

Hazen Research, Inc., has developed a new process for removing pyritic sulfur and ash from coal. Feed coal is contacted with iron carbonyl vapors, Fe(CO)5, at 190°C which puts a thin skin of magnetic material on the pyrite and ash, but does not affect the coal. Thus, low intensity magnetic separators yield a nonmagnetic coal, low in sulfur and ash, and a magnetic refuse, high in sulfur and ash. Results are given for clean coal produced by this method. A comparison is made between results of the magnetic process and the U. S. Bureau of Mines two-stage flotation process cleaning identical samples of Pittsburgh Coal. Capital and operating costs of the two cleaning methods are discussed.

Jan 1, 1976

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calcula¬tions where the compliance limit of lbs S02/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equa¬tions to blend to an SO2 content of 1.2 lbs S02/million Btu; the excess sulfur for Coal A was defined as Sulfur excess%o = 0.5 - 0.6-13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C<- 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: ? W is the total weight; ? A, B and C are the fractional proportions of each potential blend stocks; ? Sa, Sb and Sc represent the percent sulfur content of the blend stocks; ? Ha, Hb and He represent the calorific content of the blend stocks in Btu/lb; and ? H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1997

By J. W. Craven, M. Katom, K. M. McCaffery

At Ok Tedi, ore type and SAG feed size distribution vary widely and frequently. This makes control of the SAG mills by application of the power/pressure relationship difficult. Power logic has traditionally been conservative due to power spikes associated with rapid size distribution changes. A new expert system was installed in early 2000. The system incorporates multiple state fuzzy logic to deal with frequent and radical ore type and size variations, along with monitoring of motor temperatures. A short term power spike no longer warrants immediate radical action. This has resulted in increased mill throughput and improved circuit stability.

Jan 1, 2001

By J. J. K. Daemen

Mining Engineering education is in trouble, if not in crisis. The most visible signs are the decrease in the number of programs that offer the degree, and the continued difficulties in attracting students to the discipline. Unless these trends are reversed, the future of the profession is uncertain, at best. Remedies have been proposed, and some are drastic. They range from consolidating mining engineering education into one or two national schools, to cooperative regional programs, to distance education programs, and to proposals to limit mining engineering to a graduate degree or specialization only. These alternatives deserve serious attention and merit discussion. I hope that one alternative that will remain on the table is the classical and traditional “School of Mines”. A reasonable number of such schools are needed to provide the educational diversity and the critical mass to maintain accreditation and professional registration for their graduates. Most importantly, such an approach is most likely to assure the continued existence of mining engineering as a profession. It also provides the best educational framework to teach mining engineers. However, such Schools are vulnerable, highly susceptible to university budget pressures, and probably can survive only with strong external support.

Jan 1, 2004

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005

By C. R. Landis

The Wyoming bentonite industry finished 2005 with strong growth. For most of the markets, demand exceeded supply. The industry continues to be heartened by the strength of its longtime markets, oilfield and iron ore pelletizing markets. But overall, all of the major markets enjoyed good to excellent commercial conditions. Growth at the macroscale was fueled by the continued strong domestic economy, by the exchange rate of the U.S. dollar in global markets and by strong worldwide global demand. As result, two new greenfield operations are in the early stage of development in the Wyoming region for the first time in more than two decades.

Jan 1, 2006

By S. Hamilton

Occurrences of boron-containing ores are relatively rare on a global basis. The first verifiable use of borax was in the 8th century by Arabian gold and silversmiths. Due to the rarity of the borate mineral occurrences, borates were originally traded at relatively high prices and were used for very specialized applications. Today, there are

Jan 1, 2006