Search Documents

By James M. Neilson

In contrast to the rather generalized title of this paper, the subject of discussion will deal with two specific cases of sliding in glacial lake clays in northern Michigan. The slides in question occurred on lands owned by the Upper Peninsula Power Company a short distance south of Lake Superior. Slope failure problems have plagued the Company's operations for many years. It is hoped that this paper may provide some insight into the causes and possible mechanisms of clay slides in general as well as providing details of the two slides specifically cited. LOCATION The Upper Peninsula Power Company's Victoria facilities lie in section 29, T. 50 N., R. 39 W., in Ontonagon County, Michigan. The power site is situated on the West Branch of the Ontonagon River, approximately five miles southwest of the town of Rockland and only one mile to the southeast of the old mining location of Victoria. The area lies wholly within the Precambrian Shield and it is geologically similar to adjacent parts of Wisconsin, Minn¬esota, and Ontario. (Figure 1). THE VICTORIA HYDROELECTRIC SITE The Victoria hydroelectric power facilities were constructed in 1930 on a portion of the West Branch where meanders are conspicuously developed. The generating station is actually sited on an abandoned meander at a place where valley widening has occurred. Water is conducted from Victoria Dam through a 6000-foot, 10-foot diameter wood stove pipe - through a surge tank - and into the powerhouse where

Jan 1, 1971

By J. Kretschmann, P. Goerke-Mallet, C. Melchers

Mining always leaves a mark behind. Dealing with this legacy is not only a tremendous challenge in Germany, but internationally too. The Technical University Georg Agricola (THGA) in Bochum, Germany, has established a Research Center for Post-Mining. Researchers combine expertise from a variety of technical and nontechnical fields in their quest to shape the post-mining era that completes the mine life cycle. In this respect, the Research Center focuses on four research areas: Perpetual tasks and mine water management, Geomonitoring, Material sciences and site transition. With more than 200 years of successful partnership with the mining industry in Germany and abroad, THGA offers a perfect setting for fresh and sound ideas in order support mining’s social license to operate. The aim of the paper is to describe the Post-Mining Research Center along with exemplary research projects that are of interest to the mining industry globally and to foster technical communication and research networking.

Mar 2, 2022

By L. Mukka

The existing main mine ventilation system for the production areas to the Kiruna mine was constructed during the period 1994-1996 and extended with 4 more shafts, including fan stations, for the sea ore body from 1997-1998. Two papers have been presented from this project at the 7th US Mine Ventilation Symposium in 1995 and at The 6th International Mine Ventilation Congress in 1997. In 2005, pre-studies for a new main haulage level were started. Different haulage methods were presented including ventilation systems. The pre-studies showed that the existing ventilation system, including fan stations for the new main haulage system in the production area, could be extended. However, a new system for the central area, which was not in the initial investment program, would be needed. In the beginning of 2006, a decision was made to design a new ventilation system for the central area to make it possible to get air to the development work for the new main haulage system, independent of the haulage method. This system was operational by the beginning of 2007. The new main haulage system, which was decided to be located on level 1365 m, only requires that the existing shafts be extended - the capacity of the fans seems to be enough. However, the problem is that the existing level 1045 m and the new level 1365 m have to be in operation in parallel for approximately 7-8 years. The challenge for the moment is determining how to ventilate the production areas for both levels at the same time, while simultaneously constructing the extended system. This paper will describe the problems associated with the extension of the main ventilation system and some potential solutions for these problems. The new main haulage level 1365 m must be in operation by 2012.

Jan 1, 2009

By J. Haynes

Coal mines in the eastern US often use sloped shafts as production beltways for ore removal, as means of access for supplies, and for ventilation. These structures are usually completed with the help of a contractor. In late 2011, Frontier-Kemper Constructors was engaged to build a slope for a coal mine in southern Indiana. Although the site was located in familiar Illinois basin formations, the geology proved to be very difficult. This paper describes some of the challenges faced during excavation of this slope and the methods used to overcome them, including changing the method from conventional drill and blast to cutting with a continuous miner.

Feb 27, 2013

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

Because of its many advantages, roof bolting has been widely used in hard-rock underground mines. In this paper, the applicability of roof bolts to mine openings in frozen ground, and the affects of bolts on the stability of the openings are presented. A comprehensive finite-element program, ABAQUS, was used to analyze the temperature distribution, the stress field and the displacement, field around a mine opening. Openings that were supported by roof bolts and openings that were unsupported were both analyzed. The thermal and mechanical processes were treated as a quasi-coupled problem, with the thermal analyses being conducted first, followed by the mechanical analyses in each case. For the opening under consideration, i.e., a roof area of 15 m2, five to seven roof bolts are appropriate. When the number of bolts is less than five, the displacement within the ground can be improved only locally.

Jan 1, 1997

By S. Assemi

Interaction forces between a hydrophilic silica particle and an air bubble were measured by atomic force microscopy using simplified model systems with deionized water and dilute KCl solutions. Contributions from the hydrodynamic force were minimized by using a low piezo speed. Particle-bubble separation distance and the bubble spring constant were calculated from linear regression of the piezo extension versus cantilever deflection. The bubble surface potential was then estimated from fitting the AFM-measured forces to the Hogg-Healy-Fuerstenau (HHF) model, using the surface element integration (SEI) method. Surface potentials obtained for the bubble at a low applied force were comparable with the literature data, suggesting that the simplified model used here can give a reasonable estimation of the bubble surface potential under moderate applied forces. Interaction forces between a silica particle and an air bubble were also measured at different locations on the air bubble surface. The force curves obtained at the edges of the bubble fitted very well to the theoretical force curves regardless of the applied force, while curves obtained at the center and halfway to the center, were more difficult to fit, in particular at higher applied forces (> 13 nN), suggesting that force curves obtained at the edges of the air bubble might be less prone to deformation effects.

Jan 1, 2008

By David van Cleave, David L. Rome

Whether you buy your minicomputer from a manufacturer or another vendor, the first thing you must do is define your needs. With good planning, the initial cost will be low and your return on investment will be maximized over the long term. Involving all members of your staff who will he using the new computer in the planning phase is also important. Their participation will alleviate any potential concerns they may have about new equipment, and their suggestions will provide valuable input for your specifications. After you define your proposed system, survey available hardware and software. The survey will help you in the next step, preparation of specifications. The specifications, along with a quote request, are then sent to various manufacturers. Consider the Manufacturer When selecting your minicomputer, one important item to consider is the manufacturer. Remember, when you buy a computer, you're also buying the services of a computer company. A firm that makes a commitment to its customers and provides a product that is field tested before releasing it for sale is preferable. Examine the company's maintenance and support packages, since every machine requires preventive maintenance. Does your manufacturer or original equipment manufacturer (OEM) support service sites in your area? Has their service record been commendable? Will they provide training for your personnel and a supply of circuit boards so you can retain a degree of self-service autonomy? Three methods of buying a computer involve the manufacturer, an OEM, and the systems house. Buying direct from the manufacturer means you go straight to the source, using no middleman. This gives you maximum flexibility; you can consider every alternative and many possible combinations of computers, peripherals, and software until you find exactly the right system for you. The OEM buys computers direct from the manufacturer and builds them into his own computerized, special purpose product. He usually sells a complete package, including software and hardware, and often noncompetitive equipment as well (a scientific or engineering instrument, for example), designed for the mining market. Because he offers a packaged product, the OEM can often charge less for the system than if you put the pieces together yourself. In many ways, the OEM also provides a unique system. And while the OEM sells a packaged solution, he also usually has the special market knowledge necessary to modify the system to meet your unique needs, if necessary.

Jan 11, 1981

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By R. Abel, T. Wildeman, N. Heflin

A study was conducted to assess environmental effects of waste rock piles on water in the Russell Gulch area. Each pile was rated on physical characteristics of proximity to an ephemeral gulch, extensiveness of erosion features, size, presence of vegetation, and presence of a kill zone. Chemical assessments focused on three leachate tests performed on waste rock samples. Ratings were based on pH, conductivity, acidity, and analysis for 31 metals using inductively coupled plasma emission spectroscopy. The chemical and physical assessment of each site is used to make a rating of each pile on its overall potential to deliver contaminants.

Jan 1, 2004

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By Z. T. Mathe, M. A. Vera, M. C. Harris

This contribution presents a methodology how to quantify froth zone recovery in a continuously operated laboratory mechanical flotation cell. The methodology consists of relating the overall flotation rate constant to the froth depth of the flotation cell. As a result, a froth zone recovery factor (Rf) can be extracted. This froth performance parameter has been studied as a function of the flotation cell operating variables. By understanding the effect of these operating variables on Rf, an integrated methodology for modelling froth zone performance in batch and continuously operated laboratory flotation cells has been proposed. The Rf modelling is based on a semi-empirical approach which considers a number of parameters to be used. Some of these parameters may have physical significance, i. e. they may be easily and physically measured. The modelling approach consists of taking into account the interaction between the pulp and froth zones. This interaction allows froth zone recovery (Rf) to be predicted. The whole modelling exercise process lies on auxiliaries relationships which indicate the dependence of the parameters with the operating conditions of the flotation cell. This contribution is part of a larger project that deals with the modelling and optimisation of flotation plants (Project P9L, 2000).

Jan 1, 2001

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

By S. E. Phillipson

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. Geology is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks, and an extensive crystal-lithic tuff debris apron. The ore body is hosted by intra-cauldron sedimentary rocks and breccias. Fluid inclusions suggest that silver, lead, and zinc were transported as chloride complexes and precipitated by cooling in veins from <5 wt. % NaCl eq. fluids at 170°-215° C. Silver associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2001

By D. L. Ogonowski, J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m(36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached design capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM-800Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

U.S. Borax’s mine in California’s Mojave Desert is the source of nearly half the world’s supply of refined borates. These minerals are used in hundreds of products, including essential plant nutrients that increase crop yield and quality, and safe building products that protect homes from insects and the elements. Borax’s workforce is also safe. In fact, it is among the safest in the nation. In 2003, the company was recognized by the U.S. Mine, Safety and Health Administration (MSHA) for achieving the best safety record among large U.S. mining operations. It was also recognized by its parent company, Rio Tinto, for achieving the best record among its nearly 80 worldwide mining operations. Borax’s safety performance is five times better than the national average. And its workforce recently achieved more than two million hours without a lost-time injury.

Jan 1, 2004

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013