Search Documents

By L. You

Theoretical and analytical analyses of three mitigative measures- plane fitting method, trenching, and tension cable led to the development of a total protection plan to eliminate or reduce damages to the residential structures subjected to surface movements caused by underground longwall mining. The protection plan was applied to twelve residential houses and two external garages. The success rate is overwhelming. This paper describes the methods employed for protection and results of those case studies.

Jan 1, 1986

By Neal Retzer, Adam Bedell, Nick Cioffredi

The first wagon trail across Loveland Pass was built in 1869 thus starting the struggle between the Colorado Rockies and interstate travel. The 1st Pioneer Bore underneath Loveland Pass at the Continental Divide in Colorado was attempted between 1941 and 1943 and was abandoned due to ground conditions at the Loveland Fault. Construction on the nearby Eisenhower Tunnel began in 1967 and was completed in 1973. Numerous challenges associated with tunneling, including at 11,000 ft were overcome. The purpose of this paper is to summarize the history of investigation and construction challenges associated with the Eisenhower Tunnel to celebrate its 50th anniversary.

Jun 13, 2023

By J. Jordan, D. K. Denton, D. Tesarik, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health integrated the results of studies from a seismic tomographic survey, a finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. The key findings were that (1) the seismic tomograms showed that seismic velocities in rock adjacent to mine openings were low, (2) a difference tomogram in which in situ stresses on the east and west sides of the slot were compared showed that velocities increased west of the slot but decreased east of the slot, (3) geologic features (rock types and a fault) identified through geologic mapping were recognizable in the seismic tomograms, (4) ultrasonic velocity measurements on the rock cores agreed with seismic velocity measurements in the tomograms, and (5) results from a finite-difference analysis compared well to the seismic tomograms west of the slot but not east of the slot. The significance of this research is that seismic tomography is a useful tool for determining relative stress in underground pillars.

Jan 1, 2004

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By B. K. Mishra

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills (14-18 ft). DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important factors such as the configuration of the liner and the geometry of the lifting surfaces are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill with particular emphasis to large diameter mills.

Jan 1, 1992

By Long An, Chao Wu, Yuanhui Li, Xing Sun, Shuai Xu, Changyu Jin

Stage open stope mining (SOSM) maintains the stability of excavation openings by leaving a large number of rib pillars. Affected by the strong unloading due to stage mining and the low width-to-height (w/h) ratio of the pillars remaining, large-scale destabilization disasters of rib pillars or excavation openings easily occur when the distribution of ground stress or the size of rib pillars is unreasonable. In view of these problems, a physical SOSM model test was carried out based on an underground metal mine in the city of Chifeng in China, revealing the deformation and failure characteristics of the SOSM pillar group by overloading.

Jul 1, 2023

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By William Gleason

The Dulles Corridor Metrorail Project is a $3-billion project that will link Dulles International Airport with the downtown center of Washington D.C. by way of a single seat train ride. The project is mostly above ground, but it does include two short, yet complex, tunnels through the area of Tyson?s Corner. The project is being completed in two phases. The Dulles Transit Partners (DTP), led by Bechtel, was awarded the first phase, a $1.6-bil-lion phase that includes 17 km (11 miles) of track with five stations. At Tyson?s Corner, the project includes twin 730-m- (2,400-ft-) long, 6-m- (20-ft-) diameter tunnels. Bechtel is self-performing construction for the $1.6-billion design-build job. Gall Zeidler Consultants was hired by DTP as designer for the NATM tunnel portion of Phase 1, and Beton-und-Monierbau was hired as tunnel subcontractor. Tyson?s Corner is an affluent and congested area that sits 152 m (500 ft) above sea level. To get through the area, it was decided that tunnels would be the best option with the least amount of disturbance to the surrounding areas. However, with extremely shallow groundcover above some points as well as soft soil throughout, the tunnels are also the most complex aspect of Phase 1. About 213 m (700 ft) was constructed utilizing the cut-and-cover method. The remaining 518 m (1,700 ft) is being constructed using the New Austrian Tunneling Method, which integrates the principles of the behavior of rock and soil masses under load, and monitoring the performance of underground construction during construction. ?The tunnel only falls 2 m (7 ft) from one end to the other and we pass through two soil conditions, they are both soft ground,? said Dominic Cerulli, tunnel task manager for Bechtel. ?Soft ground is very tricky because you have to close the ring in a timely manner to minimize settlements at the surface. If you don?t close the ring quickly to achieve a round structure that?s good in compression, the tunnel could start necking and squatting and the ground above it will settle. We are under major roadways, so excessive settlement would be a bad thing.?

Jan 1, 2011

By C. R. Nailler

Two recently published papers describing the use of psychological tests for selection and placement of coal mine personnel have created considerable interest within the Coal Industry, one paper, published in the April 1957 "Mining Congress Journal," entitled "Personnel Evaluation and Training," discusses the use of tests by the Christopher Coal Company, The second paper, published in the "West -Virginia Coal Mining Institute's 1957 Report" and in the September 1957 "Coal Age," entitled "Testing to Select Better Personnel for Coal Mining Today," outlines Hanna Coal Company's test and selection procedures. Since these rather detailed sources are readily available, and to avoid repetition of the material in them, we will confine this paper to a very brief review of the essential steps already taken by these companies and a more extensive look at newer material. Briefly, the Personnel Managers, Mr. Harold L, Durrett and Mr. Albert M,. Rowe, of the Hanna Coal Company and Christopher Coal Company, in conjunction with Dr. Quin F, Curtis, Head of the Psychology Department of West Virginia University, developed two different groups oftests for coal mine personnel, The first group oftests was designed to assist in the selection of supervisors. These tests of the supervisory group were "The California Short Form Test of Mental Maturity - Advanced Series," which gave an I.Q. rating, and the second test is known as "The Minnesota Multiphasic Personality Inventory," which measures several personality characteristics, These tests must be given, grade, and interpreted by a person trained in psychological testing. As a result of testing all of Christopher's supervisory employees (seventy in number) by this method, and then comparing the individual results with the individual ratings of the foremen on the job, a so-called foremen's scale was developed. If this resulting foremen's scale had been used to select the foremen who were rated as, the best men in on-the-job performance, it would have correctly identified seventy-four percent of that group.

Jan 1, 1958

By P. D. Rao

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. Coals from Usibelli Coal Mine and the Beluga coal field have a heating value of approximately 8,000 Btu/lb and 28% moisture. Hydrothermal treatment (at 275 to 352'C) of lump coal from Usibelli Coal Mine and Beluga coal field enhanced the heating value of the coal, on an equilibrium moisture basis, from 8,000 Btu/lb to nearly 12,000 Btu/lb. The product coal with high heating value and 0.2 % S is an environmentally acceptable premium fuel. The Hardgrove grindability index of the coal is greatly improved, further enhancing its value. Increase in hydrothermal drying temperature promotes vesiculation of resinite. Vitrinite reflectance increased to 0.72 and vitrinite was subjected to widespread visiculation resulting in a coke like structure indicative that the material went through the fluid stage.

Jan 1, 1991

By August E. Vandale

I speak to you today on the subject assigned to me, "Subsidence - a Real or Imaginary Problem", as a representative of Consolidation Coal Company (a wholly owned subsidiary of Continental Oil Company). The information I relate to you is our experience in the Pittsburgh Coal Company Division of Consol and covers the Pennsylvania properties and mines with particular emphasis on the mines in the south- western portion of the State or in the immediate vicinity of Pittsburgh, Pa. Mining of Freeport and Pittsburgh seams of coal in the Pittsburgh vicinity dates back over one hundred years. Consol, or its predecessor, Pittsburgh Coal Company, has been actively engaged in mining in the area since Pittsburgh Coal Company was organized in 1900. Pittsburgh, Pennsylvania came into prominence as the Steel City largely because of the vast reserves of high grade metallurgical coal readily available in the immediate vicinity and also because of its favorable river transportation. Early in the 1900's we operated over 100 small coal mines, with operations located in the Counties of Allegheny, Fayette, Washington, Westmoreland. We have also operated mines in Somerset and Greene Counties. Titles in Pennsylvania can be in three estates: (1) title in fee, (2) title to the mineral, (3) mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage. Consol has over the years acquired good legal title to the coal lands purchased from individual farm owners, with good broad mining rights, and in 98% or more of its title has a complete waiver of surface damage or the right to subside the surface land. In the early days of our Company, individual coal farms were purchased from land owners. Many of these titles severed the coal estate from the in fee title and good mining rights with waiver of surface were conveyed in the original severance deed. Thus, minable coal reserves were put together by the purchase of the coal under many individual farms in an area. In the early years, the mines practiced hand dug mining - later going to mechanical cutting with hand loading of the coal. Systems used were entry driving with room and rib panels. We have practiced full recovery mining as far as practical during the years of hand loading, as well as in the later years when the mines were mechanized. Mining system layouts, methods and procedures have changed from time to time to keep pace with improved mining machinery and new inovations, such as roof bolting and rubber tired haulage.

Jan 1, 1967

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By Christopher J. Bise

INTRODUCTION The principal means for transporting men, supplies, and mined material in an underground or surface mine are rail systems, conveyor belt systems, or a combination of the two. Typically, large underground mines use rail haulage from the mining sections to the hoist, with conveyor belts being used within the sections. Small mines use conveyor belts in the mains and sub- mains as well as in the panels. The size and layout of surface mines also contribute to variations in the way these haulage systems are applied. The following sections address the typical problems confronting mining engineers in designing these haul- age systems. For rail, these include rail selection and turnout design, locomotive tractive-effort calculation, and motor sizing. Belt haulage calculations include belt width and speed specifications, tension and take- up requirements, idler spacings, and motor sizing. TRACK LAYOUTS Introduction The adequacy of mine track layouts is dependent upon such factors as rail weight (Table l), suitable ties, a well-drained roadbed, and properly designed curves, grades, and track alignment. As long as the installation conforms to the manufacturer's recommendations, good service can be expected from the rail system. Typically, mining-engineering calculations for rack layouts have dealt almost exclusively with the design of turnouts. As such, the following section provides the necessary information for computing the theoretically correct dimensions of turnouts. Turnout Design Fig. 1 shows a typical turnout with an identification of the component parts. Fig. 2 identifies the variables that are used to determine the turnout dimensions. The formulas that concern the mining engineer are those listed: [ ]

Jan 1, 1986

By E. J. Haas, K. A. Rost

"This study sought to identify changes in continuous mining machine (CMM) operators’ risk perception and risk behaviors as a result of adding a proximity detection system (PDS) into their environment. To accomplish this research task, 9 CMM operators from 5 locations were interviewed. Interviews were thematically analyzed for constructs including patterns in risk perception and behavior before and after PDS integration and the process of adapting to the PDS. Operators discussed standing in the red zone less than they did before using the PDS; however, they also discussed other risky decisions they made while learning how to operate their CMM with the PDS technology such as “cheating” the technology and working faster to meet production goals. The process of relearning job tasks with technology and unintended behaviors as a result of that relearning process need to be taken into account when introducing new technology into the mine environment. The study results show an in-depth view of mine workers’ perspectives and how their job tasks and environment could be or are affected when learning how to use new technology that are relevant to companies and mine operators when introducing new technology into the mine environment. INTRODUCTION Established “red zones” can help prevent striking and pinning incidents by providing guidance to continuous mining machine (CMM) operators about where they should stand and not stand while operating a CMM. Although red zones influence operator placement positions, these guidelines are not foolproof safety mechanisms. Depending on the job task and circumstances of the mine environment, a CMM operator may unintentionally or intentionally stand in a red zone. For example, CMM operators may work in close proximity to their CMM for better visual attention cues and the ability to work at a higher rate of production [1-3]. To further enhance protection and prevent collisions between vehicles and mine workers, a proximity detection system (PDS) was developed for the industry. The PDS determines an individual’s position relative to a specific piece of machinery, issues visual and/or audible warnings to the mine worker to change positions, and, if necessary, disables machine motion [4]. The introduction of new technology within other sectors has been identified as a factor that influences work decisions. Specifically, previous research demonstrates that when technology debuts there can be an initial intrinsic risk perceived among users about how the technology will interact with their current environment and behaviors; however, these ambiguities, including the possible risks and benefits, are seldom studied [5]. Some research suggests that the constant presence of technology can disrupt situation awareness and decision-making capabilities by increasing worker responsibilities and worker cognitive demands [6-8]. Further, if workers’ perceived risks both with and without technology are misjudged, unsafe decisions that result in human error and injury may be more likely [9-11]. Although these statements are provided within a broad contextual framework, they support the need to study how technology is perceived among end users in their own environment. Because research about technological impact on worker behaviors has suggested both positive and negative consequences of technology, this issue is worth addressing in the mining industry. Specifically, research has not determined whether CMM operators view their placement choices in the red zone as safe or risky and what effect PDS technology has, if any, on risk perception and subsequent risk behavior."

Jan 1, 2015

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By V. S. Tadsen

Today, man is able to probe space because of technological advancements including the ability to control certain combustion reactions very precisely. The recent adjustment of the attitude of Skylab by radio command from earth is an excellent example of such control. It is strange, and indeed unfortunate, that very little is known about the mechanism of combustion of pulverized coal, the primary fuel for rotary kilns. The selection of a coal for direct pulverized firing of a rotary lime kiln may be determined by trial and error, persistence of sales personnel, proximate analyses, grindability, or apparent BTU cost. Occasionally, the only question asked is, "How much lime will it make?" To study the behavior of a particle of coal in the combustion stream of a rotary kiln is most difficult. We must, therefore, discuss the general mechanism of combustion of pulverized coal, and relate this mechanism to the selection of a proper coal for a rotary kiln. The classic three T's -time, temperature, turbulence -must be enlarged upon for a better understanding of the problem. Pulverized coal occupies only 0.01 per cent of the volume of air required for its combustion. This mixture behaves like a gas and the general laws governing the movement of solid particles in gasses are in effect. The differential velocity between air and coal particles depends on forced and natural convection, diffusion, and the length of time each particle is in the combustion space. As a particle of coal absorbs heat from its surroundings, it begins to give off volatiles". These gasses ignite as their kindling temperature is reached, and burn readily because of the excess oxygen immediately available. Combustion proceeds at this stage by the outward diffusion of gas from the coal particle into the surrounding oxygen-rich envelope. We could say combustion at this stage represents a small coal particle surrounded by an envelope of volatiles burning at their point of contact with sufficient oxygen. This release or expulsion of gasses from the coal may result in exfoliation or disintegration of the coal particle. If this occurs, and it is desirable that it should, it will accelerate the final stages of combustion. The escape of volatile material from the particle of coal and its subsequent combustion will cause increased turbulence around that individual particle. Ignition is maintained by radiation from gasses and solids in the combustion system, and most importantly, re-radiation from the kiln refractories and the process load.

Jan 1, 1978

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By Gordon J. Hughes

The ldaho Cobalt Belt represents a unique geologic environment containing some of the largest known reserves of cobalt in the United States. Stratabound cobalt-copper-gold deposits formed within a sedimentary basin that was generated by the rifting of an Archean cratonic block. Host rocks for these deposits are the Early to Middle Proterozoic Yellowjacket Formation comprising a suite of clastic sediments, volcaniclastics, and mafic tuffs that accumulated in the intracratonic rift basin about 1.7 b.y. ago. Rifting was probably initiated during a regional heating and doming event that may date back to 1.8 b.y. ago. During this time, other rift basins were likely to have formed in the region. They probably represent the precursors of a much larger depositional environment having characteristics of an Atlantic- type or passive continental margin where younger formations of the Belt Supergroup were deposited. The Yellowjacket Formation has been subdivided in the Idaho Cobalt Belt into three genetic units representing various subenvironments of a deepwater clastic fan complex. A northwest- trending deep-basin structural trough accumulated fine-grained muddy sediments that were periodically interrupted by distal turbidites of the subaqueous fans. Subsequent progradation caused the deposition of coarser-grained clastics of the more proximal portions of the fan complexes. Submarine fan lobes were built across northwest-trending tectonically active basin growth faults. These in-basin structures caused a great deal of penecontemporaneous deformation within the Yellowjacket sequence. Northeast-trending fault zones formed an orthogonal set of fractures that controlled the shape and size of sub-basins, and were also an influence on lateral migration of dominantly fine-grained clastic material. The eruption of mafic tuffs at about 1.7 b.y. ago added a new component to the Yellowjacket sedimentary sequence. Around the Blackbird mine area these tuffs commonly occur either near the base or within some of the sandier sequences. Since most of the sand influxes were largely controlled by basinal tectonism, the tuffs were probably erupted during tectonically active periods of basin development. The dynamic nature of the sedimentary environment probably caused much of the tuffaceous component to be mixed with other clastics and even resedimented as volcaniclastic material. In time, the change to a higher energy sedimentation regime resulted in such a dramatic clastic dilution of the tuffs that they could not survive in the areas of the vents, and, if present, they must have been distributed elsewhere in the basin.

Jan 1, 2013