Search Documents

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion (Li-ion) battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V and 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicate that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Jan 1, 2024

By M. K. McCarter

Surface mining applies to extraction of mineral resources from water and sediments of rivers, lakes, seas, and oceans; from solutions circulating through broken rock and soil; and from rock and soil excavated from the earth. Surface mining is responsible for the majority of mineral production in the United States and a substantial portion of the world?s total production. This section deals specifically with extraction methods which employ mechanical processes in a relatively dry environment to free minerals from the earth. The following section, Section 15, deals exclusively with aqueous methods. With recognition of the importance of reclamation in all activities which temporarily disturb the earth?s ecosystems, it is appropriate to classify mechanical extraction methods as either deferred reclamation or concurrent reclamation. Deferred reclamation is necessary when the shape and logistics of the excavation require that it remain open throughout the productive life of he project. Upon exhaustion of economic reserves, the opening is then reclaimed in a manner consistent with public safety, environmental acceptability, and land use policy. Methods employing deferred reclamation are commonly referred to as open pit or quarry mining. Metallic ores, industrial minerals, and coal are all extracted using open pit methods. Typical examples are provided in Chapter 14.1.

Jan 1, 2008

By J. R. Heberger, B. H. Ngo

The Safety Pays in Mining v2.0 web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app categorizes injury cost by part of body injured, by the cause of the injury, or by the nature of the injury. When the user selects one of over 150 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining v2.0 will estimate the total costs of the selected injuries and the estimated impact of total injury costs on mining company profits and will provide some examples of services and personal protective equipment on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining version 2.0 web application by discussing the development and updates to the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app.

Feb 1, 2024

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Edward Holloway

The basis for the selection of the ultimate pit for an open-pit mining operation is generally opaque. Some form of value-based analysis will generally guide the final decision; however, the value will often gradually plateau while the ultimate pit size continues to increase. There is no established framework to guide specialists in the selection of the ultimate pit, with such decisions regularly made on a somewhat arbitrary basis. The key component that is missing from the analyses typically used to select the size of the ultimate pit is risk. Once risk is quantified within the analysis framework, the decision-mak-ing range is significantly reduced and the process for select-ing the ultimate pit becomes more consistent, replicable and defensible. The technique outlined in this paper provides an approach to including risk in the process used to select the ultimate pit.

Jun 1, 2024

By J. M. Manka

American mining companies operate many drum hoists that hoist from various depths with varying payloads. This paper will review the procedure of selecting optimum wire rope constructions for these existing hoisting installations. Selection for proposed installations along with recommended hoisting parameters will also be presented. To achieve this optimum rope performance, preventative and corrective maintenance procedures will be reviewed along with examples of rope problems and their causes.

Jan 1, 1992

By S. Garcia, J. Gebhardt, D. McBride, A. Hernandez, A. Esplín, M. Cross

The Minera Yanacocha operation consists of several heaps interconnected with ponds and gold recovery plants and presents various operating challenges. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters and inventory issues. An integral component of the process water/mass balance is a model of each heap that describes heap behavior based on the individual characteristics of the heap. The heap models are linked to a mass balancing program in order to track flows and concentrations throughout the circuit. A case study of the process heap model is presented for the La Quinua heap, including results for the normal base line operation and several operational problems such as loss of solution flow to the heap (i.e., pump failure), increased flow to a section of the heap (i.e., pond volume control), effect of significant rain events, and impact of a change in material properties (i.e., change in ore type). The impact on heap operating efficiency is discussed with regard to effects on recovery and gold solution grades.

Jan 1, 2007

By Rudolph K. Hoagberg

Silica sands, primarily in coarse size ranges, are used to prop open fissures or voids created in the bedrock by hydraulic fracturing. This procedure increases the flow of gas or oil or other fluids through the bedrock. The sands used must meet various specifications relating to their physical and chemical characteristics; these characteristics are in turn related to the geologic provenance of the sand deposit. The Jordan Sandstone, a Cambrian formation which is exposed in Minnesota and Wisconsin, meets the specifications of a proppant sand by virtue of its depositional history and its sedimentary properties.

Jan 1, 1980

By Donald Hulse

"Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them…” (Agricola, 1556). In 2016, it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate.“Most commonly, the social license to operate (SLO) is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat, 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders (Bice, 2014).”A generation ago we learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three-legged stool is a very stable structure (Fig. 1).In 2016, it seems that we have added some other legs to the stool (Fig 2). The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code) addresses “social, and governmental factors…” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves.”The Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Guidelines refer to “environmental, legal and social data…(CIM 2003).”Compared to these, the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the competent person.When there are more than three legs on the stool, it is imperative that all legs be constructed exactly to the design. Any one or more legs that are out of alignment will cause the stool to wobble.Engineers are trained to create designs to meet specifications. Loads can be estimated, forces calculated and cost studies completed that will lead to, not only a stable design, but the most efficient design that meets the specifications."

Jan 1, 2015

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels ? from mining and processing to the manufacturing of Anished products. In 2009, the estimated real GDP of the United States decreased by 2.4 percent compared with, and the estimated nominal GDP was about $14.2 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. In 2009, the continued decline of the housing market was reflected in reductions in the production and consumption of cement, clays, construction sand and gravel, and crushed stone (those mineral commodities that are used almost exclusively in construction). Production of mineral commodities associated with the manufacture of goods for the housing market, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard also decreased. Declines in auto-mobile manufacturing resulted in reduced production

May 1, 2010

By A. J. Richins, M. G. Nelson, R. Dunne

From the inception of flotation in the late 1800s, coarse particle recovery has been a challenge to practitioners. By the early 1900s, flotation processes included oil flotation, skin flotation, agglomeration flotation, and froth flotation, and for each there was a proliferation of flotation equipment. Ensuring good coarse particle recovery included desliming of the feed and proper conditioning were required. Froth flotation was at first used mainly to treat finer materials from grinding circuits. The maximum size for coarse particles was from 3.18 to 4.78 mm. In froth flotation, large particles with high specific gravity tend not to be recovered. Coal and minerals of low specific gravity and flaky minerals such as graphite, mica, and talc can be floated in larger sizes. In the early 1960s, the phosphate industry began using column cells to recover coarse particle by froth flotation, but early columns suffered from poor bubble generation and sanding at the flat base of the column. Recently, improved coarse particle recovery has been the object of new cell designs—the Eriez HydroFloat™, the Jord NovaCell™, the FLS coarseAir™ cell, and the Cidra P29 integrated system. The paper will follow the development of coarse particle flotation with a focus on the development, laboratory assessment, and operation of the new flotation equipment and technology designed to recover coarse particles.

Feb 22, 2026

By Xin Zhou, Huilin Jia, Xiaofei Liu, Jinxin Wang, Zifeng Meng, Zinan Du, Hui Xie, Guihang Jiang

The change of gas emission or concentration level at the working face is one of the main precursor characteristics of coal and gas outburst. At present, coal and gas outburst monitoring and early warning are mainly based on whether it exceeds the limit and its change law. However, the gas concentration level is affected by factors such as coal seam gas content, permeability, and mining process, and the change law is complex to recognize manually. In this paper, the response characteristics of gas concentration level in the mining process are analyzed and revealed, and a bidirectional long short-term memory model is established. The change characteristics of the gas concentration level in the mining and non-mining processes are studied and recognized. The results show that the change law of gas concentration in the mining process has apparent periodicity and trapezoidal volatility. The proposed intelligent recognition method based on the bidirectional long short-term memory neural network can automatically recognize the underground mining and non-mining processes, and the recognition accuracy achieves 97.7% . The research can significantly help improve the level of coal mine safety management and the accuracy of early warning of coal and gas outburst.

Apr 29, 2023

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic meters per hour) for dozers operating in hard-rock bulk push applications. The particle size distribution of the material employed in the test rig was modeled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard-rock dozer push operations. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 to 40 m.

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024