Search Documents

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Tholana

South Africa hosts some of the world?s largest known resources and reserves of minerals that are strategically important to the global economy. The country?s mining industry contributes significantly to the national economy in terms of gross domestic product, export earnings, corporate tax receipts, remuneration earnings, and employment. Platinum, gold, and coal are significant minerals because they make the largest individual contributions to these economic indicators. Several factors impact the cash cost performance of operations that mine these minerals, thus affecting the future sustainability of these operations, which are generally ?price-takers?. It is therefore important that the cash cost performance of operations for these key minerals is analysed. Commercially available industry cost curves can be used for such analysis. However, some companies may not be able to afford to purchase these curves. This paper presents a simple Microsoft Excel® algorithm for constructing the curves. It also demonstrates how the constructed industry curves were used to analyse the cash cost performance of South African mining operations for the three selected minerals for the period 2007 to 2011, which included the 2008 global financial crisis. The analysis revealed that the operations were affected by several global and local factors during the review period. The work reported in this paper is part of an MSc research study at the University of the Witwatersrand. Keywords cost curve algorithm, economies of scale, cash cost performance

Jun 1, 2013

By R. A. Plumbridge

The Honourable Mr Molefe, Premier of the North- West Province; Or Scot-Russel, Chairman of the CMMI's XV Congress; Mr Loton, Chairman of the CMMI; distinguished guests, ladies and gentlemen. At the outset may I express my sincere appreciation to the organisers of this Congress for their kind invitation to me to participate in the plenary session. May I also thank the CMMI for inviting me to be their fifth distinguished lecturer. This is a signal honour and one which is sincerely appreciated by my Group and myself. The subject of gold is a very emotive one. It conjures up different images in the minds of a wide variety of people. For many of us it is very simply the ultimate metal. In ancient times gold was sought after and treasured; it was the chosen metal for adornment and many of the best preserved artefacts of that time were hand-fashioned from gold which had been won by primitive mining techniques. Gold's rarity and its value was recognised by those who fashioned the earliest gold coins thus underlining gold's special place as a store of value.

Jan 1, 1994

By S. Chai

Waste dumps are widely used to discharge stripped mine wastes in open pit mining methods. As mining progresses, the height of the waste dumps will increase gradually, which may induce sliding failure once the height exceeds a critical value. Therefore, estimation of the maximum dumping height is crucial to the life-cycle use of a waste dump. However, published information about the maximum height of mine waste dumps are extremely rare. In this study, the maximum dumping height is estimated based on the strength-reduction technique by numerical simulations. The influences of dump geometry and properties on the maximum height are investigated. The results show that the maximum dump height decreases as the dump slope inclination angle α or the unit weight of dump materials γ increases, but decreases when the shear parameters of dump materials (cohesion c and internal friction angle ϕ) increase. The maximum height starts to increase with the ground inclination β when shear failure occurs at the interface between the dump and the base. Furthermore the effects of the dump width B, Young’s modulus E, and Poisson’s ratio μ of dump materials on the maximum height are almost insignificant. Good agreement was found between numerical results available in the literature and those obtained in this study.

Oct 1, 2022

By M. Onifade, B. Genc, P. O. Akinseye, M. Fourie, K. O. Said

Coal is mined by both surface and underground methods and its extraction is normally characterized by numerous hazards that can lead to catastrophic accidents, which result in devastating effects such as injuries or fatalities, damage to mining assets, and destruction of mineral resources. These hazards exist due to the ability of coal to support combustion and its association with toxic, flammable, and explosive gases. Underground coal mining entails higher safety risks than opencast coal mining, chiefly because of issues relating to mine ventilation and mine collapse. Furthermore, coal mine collapses mostly occur due to crumbling of mining supports, especially in room and pillar mining systems. To avoid such adverse occurrences, safety management systems need to be in place. This study reviews the various technological safety systems and principles that are used for safe-rescue and self-escape of miners in underground coal fires, particularly in South Africa, using data obtained from Mines Rescue Services in Carltonville, South Africa. The outcome of the review shows that practising safety culture has been given priority across many South African underground coal mines through setting up safety management systems and encouraging workers to stay committed to safety principles.

May 2, 2022

By R. Webster

"Daniel Krige’s influence on soil science, and on soil survey in particular, has been profound. From the 1920s onwards soil surveyors made their maps by classifying the soils and drawing boundaries between the classes they recognized. By the 1960s many influential pedologists were convinced that if one knew to which class of soil a site belonged then one would be able to predict the soil’s properties there. At the same time, engineers began to realize that prediction from such maps was essentially a statistical matter and to apply classical sampling theory. Such methods, though sound, proved inefficient because they failed to take account of the spatial dependence within the classes.Matters changed dramatically in the 1970s when soil scientists learned of the work of Daniel Krige and Georges Matheron’s theory of regionalized variables. Statistical pedologists (pedometricians) first linked R.A. Fisher’s analysis of variance to regionalized variables via spatial hierarchical designs to estimate spatial components of variance. They then applied the mainstream geostatistical methods of spatial analysis and kriging to map plant nutrients, trace elements, pollutants, salt, and agricultural pests in soil, which has led to advances in modern precision agriculture. They were among the first Earth scientists to use nonlinear statistical estimation for modelling variograms and to make the programmed algorithms publicly available. More recently, pedometricians have turned to likelihood methods, specifically residual maximum likelihood (REML), to combine fixed effects, such as trend and external variables, with spatially correlated variables in linear mixed models for spatial prediction. They have also explored non stationary variances with wavelets and by spectral tempering, although it is not clear how the results should be used for prediction. This paper illustrates the most significant advances, with results from research projects."

Jan 1, 2015

By H. Mulder, M. C. Bekker

The objective of this paper is to describe the research followed in creating a generalized, readiness assessment tool for mining projects. We start by highlighting the need for the assessment tool and then progress towards explaining the methodology followed during the study. The selection and finalization of the list of elements, sections, and categories that make up the unweighted values are described, followed by a summary of the weighting process applied. The outcome of this process is a weighted readiness assessment tool for mining project studies. The main benefits of the tool are that it will guide decision-makers and project managers through the definition phases of the project and improve the likelihood of project success.

Jul 2, 2022

By S. Dey, C. Bhar, S. K. Mandal

Loading and hauling of ore and waste are the key operations of an opencast coal mine and entail a high operational cost. The productivity of a mine can be increased by reducing the cycle time of loading equipment as well as utilizing dumpers optimally. In this paper we discuss the impact of rock type, bucket fill factor, rock fragmentation, the height of the cut, and angle of swing of the bucket on shovel performance. A time study is conducted on shovels in an opencast coal mine with experimental blasts of rocks to assess the impact of different factors on the performance of the shovel. Based on the data, the authors applied multiple regression (MR) and artificial neural network (ANN) techniques to develop different models for the prediction of the shovel cycle time. Developed models are validated by comparing the predicted data with actual field data. With the help of the best model, the plausible fleet size is determined in order to utilize the shovel and dumper optimally and to improve the performance of shovel–dumper operation.

Oct 1, 2022

By M. Karsten

Platinum mines in the Bushveld Complex are located in areas with a high geothermal gradient. This means that, compared to, for example, gold mines of the Witwatersrand region, high rock temperatures are encountered at relatively shallower depths. Thus air cooling and refrigeration need to be considered at early stages in mine development. Another factor that influences air cooling and ventilation requirements is the use of trackless diesel equipment for loading and hauling broken rock. At shallower depths it will be more cost-effective to locate the cooling and ventilation equipment on surface, whereas for deeper mines the more cost-effective option is to locate cooling equipment underground. For intermediate depths, trade-off studies need to be undertaken to determine the optimum mix between more cooling and less air or more air and less cooling, as well as the optimum location for this cooling equipment. Factors that are taken into account include power requirements, positional efficiency, and additional infrastructure requirements. Traditionally the approach has been to ventilate ?all of the mine all of the time?. However, with increasing power costs and growing pressure to ensure sustainability, this strategy must be modified to apply ventilation and cooling on demand. In other words, both cooling and ventilation equipment should be operated only when needed and should be adjusted to the demand at the time. Obviously there will be areas that will need to be ventilated (and cooled) continuously (for example, for dilution of flammable gases), but this can be built in to the overall strategy. In addition, in devising ventilation on demand (VoD) strategies, occupational criteria relating to exposure to gases, noise, and heat need to be taken into account. This paper discusses options available for implementing energy-efficient ventilation and cooling systems and suggests ways of changing traditional thinking in the overall ventilation and cooling of mines. Efficient ventilation and cooling designs can play a major role in improving sustainability and reducing energy costs and carbon footprint.

Jan 1, 2012

By Z. Gxowa, L. H. Chown, U. Curle, G. Govender

This work evaluates the deformation behaviour, at warm working temperatures, of green particle-reinforced aluminium composites produced by powder blending in a high-energy ball mill. The work focuses on metal matrix composites (MMCs) based on the 2124-Al alloy, reinforced with 10 or 15 vol.% SiC and metal matrix nanocomposites (MMNCs) based on the 2124-Al alloy, reinforced with 5 or 10 vol.% Al2O3. Three batches for each powder were blended and powder properties such as particle size distribution (PSD) and shape were consistent after blending. It was observed that a more uniform distribution of the reinforcement phase in the aluminium alloy matrix was achieved in 2124-Al/Al2O3 than in 2124- Al/SiC composites. The powders (unreinforced 2124-Al and blended) were initially over-aged at 350°C for 2 hours to reverse any natural ageing that may have occurred prior to use. The over-ageing was incorporated to improve compressibility of the powders with the aim of achieving green compacts with higher integrity. Uniaxial compression tests performed at ambient temperature on a Gleeble® 3500 thermomechanical simulator were unsuccessful as the green compacts fragmented. Engineering stress-strain curves showed that green compacts of unreinforced 2124-Al, 10%SiC MMC and 5%Al2O3 MMNC deformed in a similar manner at ambient temperature and had the same compressive fracture stress of approximately 170 MPa. When the deformation temperature was increased from ambient to warm working temperatures (170–280°C) it was observed that electrical resistance heating (the heating mode of the Gleeble®) of unreinforced Al alloy, MMC and MMNC green compacts did not occur. This was attributed to the high electrical conductivity of aluminium, which resulted in poor heat generation due to the low electrical resistance in the samples. It was presumed that the small sample size (d=8 mm, h=12 mm) also caused rapid heat loss. After further experimentation, the green compacts were heated successfully by insulating the samples to retain heat. It was found that at 280°C, increasing the soaking time from 6 to 20 minutes decreased flow stress and improved plastic flow in the 2124-Al/10%SiC green compact.

Jan 1, 2016

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Computational fluid dynamics (CFD) was applied to predict the average gas holdup and the axial gas holdup variation in a 13.5 m high cylindrical column 0.91 m diameter. The column was operating in batch mode. A Eulerian-Eulerian multiphase approach with appropriate interphase momentum exchange terms was applied to simulate the gas-liquid flow inside the column. Turbulence in the continuous phase was modelled using the k-_ realizable turbulence model. The predicted average gas holdup values were in good agreement with experimental data. The axial gas holdup prediction was generally good for the middle and top parts of the column, but was over-predicted for the bottom part of the column. Bubble velocity profiles were observed in which the axial velocity of the air bubbles decreased with height in the column. This may be related to the upward increase in gas holdup in the column. Simulations were also conducted to compare the gas holdup predicted with the universal, the Schiller-Naumann, and the Morsi-Alexander drag models. The gas holdup predictions for the three drag models were not significantly different. IntroductionColumn flotation is an important concentration technology that is used in the mineral processing and coal beneficiation industries. The growing interest in the use of column flotation in mineral processing has been attributed to the simpler flotation circuits and improved metallurgical performance compared to conventional flotation cells (Finch and Dobby, 1990). Flotation columns have also found other applications outside mineral processing, such as de-inking of recycled paper (Finch and Hardie, 1999).In column flotation, a rising swarm of air bubbles generated by means of air spargers is employed to collect the valuable mineral particles and separate them from the gangue minerals in a countercurrent process. Wash water, which is continuously fed at the top of the column, is used to eliminate entrained particles and stabilize the froth. The column volume can be divided into two sections – the collection zone in which the bubbles collect the floatable mineral particles, and the cleaning zone (or froth zone) where product upgrading is enhanced through the removal of unwanted particles entrained in the water mixed with bubbles from the collection zone."

Jan 1, 2019

By Janet M. Epps

The international climate regulating environmental management in mining is rapidly evolving through the combined influences of the development of international guidelines, resolutions, protocols, treaties and conventions; the influences of the international lending and aid institutions who seek a consistent but constantly evolving standard of environmental performance from their clients; the legal precedents being developed in courts al over the world; and the activities of multinational countries who tend to rapidly upgrade technological performance through their international activities (particularly influencing developing countries). In this rapidly evolving regulatory environment, the more 'models' available to this international pool of resource materials that demonstrate practical. cost-effective and (most desirably) incentive based regulatory mechanisms, the better will be the eventual body of 'international standards' we will al have to work with. Australia can make a significant contribution to this process, however, it has only been on the margin of this dynamic, North American and European led process, up to this time. It is in the Australian minerals and energy industry's best interest to take an active part in the evolution and direction of this process.

Jan 1, 1996

By B. J. Buys

Rock bolt integrity is a critical issue for the mining industry because of its influence on the safety of mining operations. Guided ultrasonic wave testing of the defects associated with resin-anchored rock bolts was investigated. Axisymmetrical and three-dimensional finite element models were built, one of a partially encapsulated bolt and the other of a bolt with a simulated local corrosion crack. Experimental bolts were then installed in a testing block and typical responses were compared to finite element models of different defect scenarios. Encouraging results were obtained for the smaller axisymmetrical and three-dimensional finite element models, as well as during the experimental investigation. It is recommended that software with energy-absorbing elements should be utilized to consider higher frequencies and longer bolts. Once the integrity of models such as these has been established, the models could in principle be used to train neural networks for use in commercial equipment to determine the integrity of the installed bolt.

Jan 1, 2009

By S. T. L. Harrison, A. Kotsiopoulos, M. D. Maluleke, E. Govender-Opitz

In the extraction of base metals from printed circuit boards (PCBs) using bioleaching, the accumulation of metal ion stress in solution has been shown to inhibit the microbial regeneration of ferric iron. This poses a challenge for the development of this technology for e-waste treatment. The paper explores the application of a microbial immobilisation system in a two-stage bioleaching system consisting of a chemical leaching reactor in series with a microbial ferric iron regenerating reactor to mitigate microbial inhibition and to enhance base metal extraction. A mixed microbial culture dominated by L. ferriphilum, L. ferrooxidans and At. Caldus was maintained over a period of two months in the presence of polyurethane foam which acted as the biomass support particle. Microbial metabolic activity of immobilised cells and their tolerance to inhibitory Cu ions was investigated. Results showed that immobilised microbial cells maintained higher ferrous iron oxidation activity compared to planktonic cells in the presence of increasing Cu2+ concentrations up to 6 g/L. This presents an opportunity for microbial immobilised systems to be adopted in two-stage bioleaching system. Keywords: Bioleaching, microbial immobilisation systems, microbial inhibition and ferrous iron oxidation

Jan 1, 2020

Measurements of the rates of penetration at various throttle air pressures are presented as a function of thrust for three different rockdrills when drilling quartzites with strengths of 45 000 lb/in2 and 39 000 lb/in2, The rate of penetration at optimum thrust is shown to agree well with the predictions of theory and curves of air consumption as a function of throttle air pressure are presented. Man-held machines are shown to be under-thrusted at throttle air pressures above 40 lb/in2g. Measurements of bit wear as a function of distance drilled are presented graphically and discussed in terms of the theory developed in Part 1.

By M. S. Moholwa, J. D. Steenkamp, H. L. Rutto

Manganese ores are the major source of manganese for the production of manganese ferroalloys. There is a gap in the knowledge of the decrepitation behaviour of manganese ores, which presents a problem in the operation of smelters. Decrepitation, which is the breakage of the ore particles upon heating, is an important quality parameter for these ores. The purpose of this investigation was to determine the extent to which South African manganese ores decrepitate during preheating in a rotary kiln. The effects of temperature, rotational speed, and particle size decrepitation were investigated. Manganese ores were heated in a laboratory-scale rotary kiln at temperatures of 600, 800, and 1000°C, and rotational speeds of 3, 6, and 12 r/min. The size ranges were +6-20, +20-40, and +40-75 mm and the residence time was constant at 30 minutes. The decrepitation index (DI) is quantified as the ratio of the mass of <6 mm particles after pre-heating to the total mass of the sample. It was found that the DIs for all ores used were proportional to the temperature and the rotational speed and inversely proportional to the particle size range with temperature being the most important parameter. Ore A was the most susceptible to decrepitation followed by ore C and ore B; this was mainly to the decomposition of kutnohorite, the content of which was the highest in ore A and the lowest in ore B.

Nov 30, 2022

By S. Shi, X. Xia, F. Xuesai, Z. Shen, D. Han

The hydrodynamic characteristics of a mechanical flotation cell’s transportation zone have significant impact on its metallurgical performance, especially on coarse particles recovery efficiency. However, how to define and adjust the transportation zone was seldom investigated by researchers. In this paper a method will be introduced to define the boundary of the transportation zone by PIV measurement. It is found that the transportation zone can be extended upwards by enlarging the entire rotor-stator assembly from the bottom of tank and increasing the jet angle of the impeller. Two control methods have been validated in industry tests on KYF-160m3 and KYF-320m3 air-forced mechanical flotation cells. The result shows coarse particles recovery are both improved distinctly. It is suggested that enlarging the top transport boundary is able to helpful to reduce the floating distance of bubbleparticle aggregates, which contribute to improve coarse particle recovery in large flotation cells. Key Words: Flotation cell; Transportation zone; Coarse particles flotation

Jan 1, 2020

By D. W. Dean, J. A. Ryder

"A computer system designed to assist in maintenance scheduling and costing, and in monitoring the performance of equipment, is described. The emphasis is on the information retrieval and implementation aspects of the system.INTRODUCTIONThe cost of the maintenance of equipment can account for a substantial proportion of the total costs of any large industry. These costs are made up of the following elements:(i) capital expenditure,(ii) maintenance labour,(iii) maintenance spares,(iv) maintenance overheads,(v) production losses.Control of these cost elements cannot be achieved without a system which maintains and retrieves the necessary infor¬mation efficiently.The system should provide engineering management with the information necessary to:(i) establish the cost of maintaining items of equipment,(ii)establish the economic life of equipment,(iii) determine breakdown patterns for the establishment of optimum inspection, service and overhaul frequencies,(iv) establish work schedules for those responsible for the maintenance of equipment,(v) establish the optimum maintenance labour complement,(vi) establish the optimum stockholding of maintenance stores items,(vii) improve the performance of equipment,(viii) justify the selection of a particular type and make of equipment,(ix) establish the reasons for any abnormal usage of materials and labour, and to(x)reduce the dependence on the human element for the control of equipment maintenance activities.Many industries have comprehensive and numerous equipment maintenance records but they experience great difficulty in retrieving the required information in the time available and with the labour available. Many industries do not bother to maintain meaningful records, because of this difficulty."

Jan 1, 2014

By Gernot Beer, Christian Dünser, Marcos Noronha

The main findings of the joint research initiative “Numerical Simulation in Tunnelling” and a follow-on project on efficient numerical simulation models for tunnelling are presented. Die wichtigsten Resultate des Forschungsschwerpunkts „Numerische Simulation im Tunnelbau“ und einem Folgeprojekt über effiziente numerische Simulationsmethoden werden präsentiert Les résultats les plus importants du point principal de la recherche "simulation numérique dans la construction de tunnels" et un projet consécutif sur des méthodes de simulation numériques efficaces sont présentés

Jan 1, 2003