Search Documents

By V. Sheikhzadeh, M. R. Sheikhzadeh, A. Haratian, M. Zare

High Pressure Grinding Roll (HPGR) as an efficient grinding technology plays a major role in mineral processing plants. Investigating the effects of this technology on different parts of mineral processing circuits reveals this technology’s capability. In this paper, HPGR grinding effects on an iron ore beneficiation circuit, in comparison with conventional crushing systems were studied. A representative feed sample was taken from an iron ore beneficiation plant, then crushed to minus 6 mm in a laboratory by two methods: HPGR and cone crusher, and finally a concentrate plant circuit was simulated. Plant simulation was performed by doing laboratory tests consisting of grinding, magnetic separation, flotation and filtration on HPGR and cone crusher products, respectively. According to comminution tests results, in particle sizes smaller than 6 mm, a cone crusher product is coarser than an HPGR product. Also, the Bond ball mill work index of the HPGR product was 10% less than the crusher product. Therefore, based on the Bond formula in applying HPGR, ball mill power consumption decreased by 12%. After ball milling to minus 100 microns, magnetic separation tests results showed that the recovery of the cone crusher circuit output was 90.8% and the product Fe grade was 66.4%. For the HPGR circuit these figures were 87.6% and 67.3%, respectively. Therefore, by using an HPGR, a higher Fe grade of the final concentrate was achieved. A flotation test was then performed on the magnetic separation concentrate, where the results showed that the crusher circuit recovery and the sulfur grade of the product were 96.5% and 0.192%, respectively; whereas the HPGR circuit recovery was 97.2% with a sulfur content of 0.185%. Findings revealed that flotation performance in the HPGR circuit was more efficient than the crusher circuit. Vacuum filtration tests on concentrate produced through the HPGR circuit resulted in a moisture content of 12% that was 2% higher than the crusher circuit’s concentrate in the same condition. Keywords: High pressure grinding roll, power consumption, magnetic separation, flotation, filtration

Jan 1, 2020

By D. Yu, Y. Thibault, D. Paktunc

"Prereduction and flux-aided direct reduction of chromite provide significant advantages in reducing energy consumption and greenhouse gas emissions during ferrochrome production. In this investigation, a comparative evaluation of the influences of several alkali fluxes was carried out based on experimental observations supplemented by advanced material characterization and thermodynamic predictions. Direct reduction of a chromite ore with alkali fluxes at 1300°C for 1 hour produced (Cr,Fe)7C3 type alloys with Cr/Fe mass ratios from 0.7 to 2.3. Among the alkali fluxes, reduction aided by NaOH resulted in a high degree (85%) of Cr metallization with the ferrochrome alloy being Cr4.2–4.6Fe2.4–2.8C3. The formation of liquid slag, which facilitated Cr metallization, was limited by the formation of NaAlO2 between 800 and 1300°C. This, in turn, restricted the collection and transport of the charged ionic Cr species (i.e. O2–) to graphite particles. Under the conditions studied, ferrochrome particles were often small and largely unliberated, which would make the physical recovery of ferrochrome challenging. At 1400°C, the amount of liquid slag increased, enabling the growth of alloy particles. Direct reduction of chromite aided by NaOH is promising as an alternative technology to conventional flux-based smelting in electric arc furnaces. IntroductionConventional smelting processes are energyintensive (Riekkola-Vanhanen, 1999) with the energy requirements greater than 4 MWh/t (Naiker and Riley, 2006; Beukes, van Zyl, and Neizel, 2015), and the greenhouse gas emissions can be significant, exceeding 10.5 t CO2 per ton Cr in ferrochrome produced (International Chromium Development Association, 2016). These include emissions occurring on-site (smelter), emissions due to electricity production, and emissions due to upstream processes. Overall energy requirements are influenced by the degree of prereduction and smelter charge temperature. Significant reduction in electricity consumption can be realized if the charge is prereduced before feeding to the submerged arc furnace (Niayesh and Fletcher, 1986). This consideration has led to the development of several prereduction technologies, with the most important example being the Premus process. In comparison to the conventional smelting processes, this prereduction process lowers the overall energy consumption and greenhouse gas emissions by about one-third (Naiker, 2007)."

Dec 1, 2018

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

It is shown that, when a flat-bottomed indentor is pressed into the surface of a strong rock, the normal force necessary to cause failure of the rock is reduced substantially if a shear force is applied to the indentor. A mathematical analysis is described, which shows that higher stresses are induced in an elastic material close to the free surface of the material ahead of a punch when a shear force together with a normal force is applied to the punch. Therefore, failure of the material would occur with lower forces applied to the punch. Stress trajectories show that fractures develop in the rock along lines of maximum principal stresses.

Jan 1, 1978

By A. Angelov, U. Peukerd, S. Gaydardzhieve, A. Stefanov, K. Grossman, V. Stoilov

Flotation concentrate originating from the Asarel-Medet porphyry copper mining and processing complex in Bulgaria has been subjected to regrinding using a Ro-Star mill; the effects of which on the downstream metallurgical behaviour are discussed. Particularly the effect on the liberation degree was studied through an optical microscopy and MLA-SEM automated mineralogy. On the other hand, copper selective flotation of the reground bulk concentrate was realised to evaluate the anticipated metallurgical improvement. Process parameters such as involvement of prior hydrocycloning and variation of collector dosage have been evaluated. Within a two-minute residence time inside the Ro-Star mill, an improved liberation degree of the copper bearing minerals has been observed. As a consequence, enhanced copper recovery and selectivity against pyrite was noted. It has been found that in order to guarantee efficient flotation of the resulting ultrafine particles, a modified flotation regime (i.e. changing collector suite and dosages) should be followed. Keywords: RoStar Mill, liberation, flotation recovery, ultrafine particles

Jan 1, 2020

By B. G. Meyburgh

E. H. D. Carman: The results achieved at Buffelsfontein Gold Mining Company Limited are very encouraging and it seems certain that as far as the conventional uranium recovery process is concerned solvent extraction must entirely supplant the old resin ion exchange process. The operational costs given by Mr Meyburgh indicate that the chief cost items in solvent extraction are reagents. In other words 38.4 per cent of the operational cost at Buffelsfontein is due to the replacement of the organics lost from the plant. It is reported from a wide field of experience that loss, particularly of amine, is a direct function both of the quantity and nature of finely divided suspended solids in the pregnant solution and the extent to which the design of the mixers causes the formation of secondary dispersions which do not easily separate in the settler. There is in addition the unavoidable loss of amine due to its solubility in the aqueous solution which is thought to be about 4 p.p.m. In order to minimise solvent losses therefore, efficient clarification at the head of the solvent extraction plant would appear to be a most important requirement. For this reason the newly erected plant at West Driefontein Gold Mining Company Limited has two Funda Pressure Filters each with a filtering area of 540 sq. ft. which are together designed to handle up to 440 g.p.m. of filtrate. This plant has not yet been commissioned but preliminary testing indicates that suspended solids in the sub micron size range which do not settle even on protracted standing of the solution, will rapidly blind the clarifiers. This should not affect solution clarity but frequent backwashing adds to the cost of precoating. The difficulty was countered in the laboratory with continuous additions of filter aid in addition to the precoat but, as Table 11shows, cost of filter aid is high and its use will have to be optimized against organic losses due to less efficient clarification. This will need much careful observation over a relatively long period of time. Costs shown in Table 11 are based on Mr Meyburgh's figures adjusted to probable conditions at West Driefontein Gold Mining Company Limited. The assumption based on small scale testing is that it will cost 5.2c/ton in filter aid to clarify filtrate to a level of about 5 p.p.m. of suspended solids, in order to restrict the amine loss to 10 p.p.m. which is likely to be equivalent to an entrained organic loss worth approximately only 2.6 cents per ton. Of course poor clarification as mentioned earlier is only one of two or even more causes of organic losses and it seems obvious on the above basis that the operation and economics of pressure clarification will need close investigation. A second important consideration at West Driefontein has been the design of the pump-mixers which must perform the dual function of phase mixing and providing the necessary hydraulic gradient for counter current flow of the two phases. The arrangement is shown in Fig. 1.

Jan 10, 1970

By A. Chuma, K. J. Nyembwe, H. Simonsen, J. H. Potgieter

Different concentration techniques were evaluated for preconcentration of a mineral ore at a coarser size to avoid energy and resource wastage. Specifically, the aim was to reduce milling costs and energy required in the beneficiation of tin. In this study, cassiterite (0.17% Sn) was the mineral of interest in a pegmatite ore body associated with quartz (SiO₂ > 60%) and alumina (Al₂O3 > 20%). Three concentration techniques, namely dense media, shaking table, and flotation, coupled with characterization analysis, were used to assess the concentration response. The results confirmed that particle size and mineral liberation impact the separation process. High recovery and grade were obtained with gravity concentration methods (dense media and shaking table) for coarser (+300 to +212 μm) and intermediate (+150 to +53 μm) particle sizes. Lower recovery and grade were identified for much finer sizes (−53 to −38 μm). Flotation produced a high-grade product at a relatively low recovery and appeared to be only applicable to finer grains. Separation efficiency based on Schulz’s equation measured a segregation performance of 74.8% for dense medium separation and 60.7% for the shaking table for the coarse and intermediate particle sizes. Flotation only achieved a separation of 30%–40%. The results suggest that use of dense media separation as a rough preconcentration method prior to further grinding, and the utilization of a more advanced concentration technique for mineral recovery and upgrade, constitute a successful approach to improve process economics.

Apr 14, 2024

By M. Hopf

Numerous developments and improvements have been made to tap-hole designs. On the other hand, there are very specific designs in operation that have endured for many years without any modification. Nobody likes design changes because of risk - the risk of atypical wear, potential hazards, and costly repairs entailing enormous production losses. So the philosophy ‘never touch a running system’ is maintained, because among other things there is no efficient working monitoring technology for tap-holes. In the past few years a couple of new technical solutions have been investigated and developed. Not all theoretical solutions are possible in practice. However, metallurgists are inventive, and the last word regarding efficient working tap-hole monitoring technologies has not yet been spoken.

Jan 1, 2014

THE THIRD INTERNATIONAL GEOCHEMICAL EXPLORATION SYMPOSIUM (Summary Account) This Symposium, co-sponsored by the Canadian Institute of Mining and Metallurgy and the Society of Economic Geologists, was held in Toronto, Canada in April, 1970. Over 700 delegates attended from 26 countries. Ninety papers were presented at the symposium and another 18 papers were read by title. The programme included: An Opening Session, Five General Sessions, a session on Remote Sensing Methods, a session on Geochemical Prospecting for Petroleum and Natural Gas, a session on Primary Halos and Lithogeochemical Methods, and a session on Statistics and Evaluation of Geochemical Data. The delegates were welcomed by Dr J. M. Harrison, President of the Canadian Institute of Mining and Metallurgy and Dr C. H. Smith, Regional Vice-President, North America of the Society of Economic Geologists. Dr D. R. Derry of Toronto delivered the opening address to the Symposium entitled 'Geochemistry-the link between ore genesis and exploration'. Dr Derry considered the various hypotheses on the origin of economic mineral deposits and expressed his belief that the next ten years will show evidence of an increased proportion of ore bodies that owe their origin, at some stage in time, to supergene agencies. He stressed that 'there are no sharp divisions between processes that form and destroy ore bodies at or near surface and those that form or destroy them at a depth of 20 kilometres in the earth's crust. The more we understand about the migration and concentration of metals the more accurately we can apply this knowledge to searching for unknown concentrations, whether at rock surface or at depth. To learn more about these processes of ore genesis we must rely on geochemical studies co-ordinated with field observations'. The five general sessions included accounts of progress in geochemical prospecting in different countries of the world, case histories describing the application of soil, stream sediment, geobotanical and biogeochemical techniques, papers on the behaviour of different elements under varied environmental conditions, discussions on analytical methods and the use of stable isotopes in mineral exploration. It is anticipated that the proceedings of the Symposium will be published late in 1970 or early in 1971 as a Special Volume of The Canadian Institute of Mining and Metallurgy. All registrants at the Symposium will receive a copy of this publication and copies will be available for purchase. At a special meeting called during the Symposium, charter members of the Association of Exploration Geochemists approved a constitution and elected an interim Council which will organize procedure and formulate policy during the coming year. The interim president of the Association is J. Alan Coope, Newmont Mining Corporation of Canada Limited, Toronto, Canada. More information on the constitution and membership in the Association will be distributed to learned societies and technical magazines in the near future. Membership will be open to exploration geochemists in all countries of the world. SOUTH AFRICAN COUNCIL FOR PROFESSIONAL ENGINEERS Report on Registration The Professional Engineers Act (Act 81 of 1968) came into force on the 14th February, 1969. At the time it was recognised that the success of the Act would depend in large measure on the extent to which engineers in South Africa would become registered professional engineers in terms of the provisions of the Act. The promulgation of the Act and its provisions relevant to registration were the subject of considerable publicity during 1969. This has resulted in a rate of application for registration far beyond the capacity of the very active committees set up for this purpose by the South African Council for Professional Engineers (SACPE). To give some idea of the task before these committees and before SACPE itself, which must ratify each case,

By Pentti Niskanen

"The ventilation system of the Pyhasalmi Mine is described. The mine is located in an area where the annual atmospheric temperature may vary from +30°C to -30°C. Natural ventilation causes serious difficulties because the underground mine is connected by drifts and finger raises to the bottom of the 120 m-deep open pit.The natural ventilation tends to make the ventilation net unstable. The paper describes how the instability characteristics of the ventilation net can be studied and how they have been taken into account when automating the control of the ventilation. In addition, the software, hardware and costs of the system are described. The system consists of 12 automated ventilation doors, two mine fans, 8 elements for sensing the air flow and temperatures, a control panel and a process computer."

Jan 1, 2014

By M. C. Holton

South Africa has the world?s largest in situ deposits of platinum group metals, but economically exploitable resources are shrinking due to escalating costs and technical challenges. The South African National Research and Development Strategy comments that an increase in the knowledge intensity of the resource-based sectors is required to turn these resources to account. Highly trained human resources, continuous improvement, technological innovation, and smart acquisition of know-how will become the major differentiators in the global mining market. Mechanization and, ultimately, automation in mining have the potential to reverse the negative mining trend and resolve safety and other challenges. However, the adoption rate of mechanized mining in platinum (and hard-rock gold) has been slow for various reasons. Changing systems from conventional drill?and-blast to continuous mechanized mining is a big step-change endeavour. The problem of transformation is discussed, and the discipline of systems engineering is examined because of its successful application in aerospace and defence.

Jan 1, 2012

By G. Howell, J. Wates, A. Coetzee, C. J. MacRobert

The Global Industry Standard on Tailings Management (GISTM) requires mining companies to make four key appointments as part of their tailings management structure. These four positions are an Accountable Executive with policymaking responsibilities, a Responsible Tailings Facility Engineer with operational responsibility, an Engineer of Record to ensure facilities are designed, operated, and closed safely, and an Independent Tailings Review Board to assess safety drivers regularly. Little guidance on the traits of these individuals is available in a South African context. Consequently, the tailings community of practice was surveyed to develop a table of ideal competencies and establish the flexibility in meeting these traits.

Jun 2, 2022

By A. Modi, C. Li, R. Kabwit, W. Y. Xinchao, R. Joshi

The KIMIN copper project can treat 1.7 million dry t/a copper-cobalt ore. It has three mills in operation, two using conventional milling in water and the third in raffinate. We introduce the project process circuit and the capital and operating costs of using the raffinate process compared with conventional milling in water. There is a capital saving of approximately 11.5% for major equipment by removing the pre-leach thickener. In addition, it also achieves an annual operating cost saving of USD 2.1 million due to an increase in 49% of acidic raffinate recycled and reduction in lime consumption. The features of CITIC’s new duplex stainless-steel ball mill ,as the key equipment of the system, are also introduced

Jan 1, 2023

Professor H.R. Philips was born in South Wales. After graduating with a B.Sc. degree in electrical engineering from the University of Bristol, he joined the National Coal Board's management training programme. Mr B. Moore was born in Coventry, England. He matriculated at Bablake School and then atended Birmingham University, obtaining a B.Sc. Mining Engineering degree in 1953. Professor J .S.J. (J annie) van Deventer matriculated at Swelendam High School. He studied chemical engineering at the University of Stelenbosch, and obtained the degrees of Hons. B. Ing. in 1978 and Ph.D. (Ing.) in 1985. Professor M.D. Brayshaw received most of his education in England but obtained his Ph.D. (Eng.) at the University of Natal. Rock fragmentation by blasting The Third International Symposium of Rock Fragmentation by Blasting will be held in Brisbane, Australia, from 26th to 31st August, 1990. The Third International Symposium of Rock Fragmentation by Blasting is designed to inform delegates on the state of the art in explosives and blasting technology, and to build on the standards of excellence set by the previous symposia in Lulea, Sweden (1983) and Keystone, Colorado (1987). Delegates with an operational, technical, or research focus on blasting will gain from this interactive symposium. Recent journal Mineral resources engineering, edited by C. T. Shaw, T.L. Car, and M. Karmis. London, Taylor & Francis, 1989. Published quarterly. US $107 per year. Risk management The Cost Engineering Association of Southern Africa (CEASA) is to hold its 3rd Biennial Symposium at Indaba, Midrand, on 25th and 26th January 1990. The title of the Symposium is Risk Management in Promotion of Capital Projects. The present political and economic environment in South Africa is characterized by a lack of financial resources, and of technical and management skills, on the part of project owners, designers, and contractors/ vendors.

Jan 1, 1989

By T. Käyhköa, J. Liipoa, S. Khizanishvilic, M. Sinche-Gonzalezb

The use of geometallurgical modelling is becoming more common in concentrator plant design and during the operational phase. Predictive modelling aims to define optimised process parameters for the concentrator plant to accommodate variability within the ore feed. The main objective of this study is to show how the metallurgical response of different types of ore blends can be simulated using kinetic models derived from experimental flotation tests with different geometallurgical end-member ore types and their blends. For these validation tests, four different end-member ore types containing different ratios of chalcopyrite, chalcocite and oxidised copper minerals from Rich Metal Group’s Madneuli copper-gold mine, Georgia, were tested. Kinetic flotation tests, including both rougher and cleaner flotation tests, were carried out. The simulations were performed using HSC Chemistry software based on mineral compositions of the ores and kinetic models using rectangular distribution equations and flowsheet model. Simulated and experimental results of copper grade, copper recovery and concentrate mass pull correlated well with R2 values of >0.95. Based on these results, the metallurgical response of different ore blends can be simulated based on the flotation kinetics of end-member ore types. The use of this kind of simulation will create savings during the test work phase and increase the flexibility and predictability in the processing stage. Keywords: Ore body characterisation, geometallurgy, process mineralogy

Jan 1, 2020

By X. Ndlovu

Underground observations in a coal mine have indicated failure oft he immediate roof above the bords. Careful observations and photographic recording of occurrences of these roof failures, termed ?roof guttering?, have been made. The occurrence of guttering results directly in roof instability, and indirectly, due to the interaction of the guttering with natural planes of weaknesses in the immediate roof rock. In this paper, relevant observations of roof guttering, possible mechanisms of formation of roof gutters, laboratory testing for determination of material strength and deformation properties, and numerical analyses to explain underground observations are described. Mapping of roof failures showed that these took place mainly towards the centre of the roadways. Roof guttering was observed often to occur violently and with little warning. Occurrence of roof guttering has a negative impact on production?some panels are abandoned, production times are increased and safety of workers is compromised. The numerical stress analyses showed that, although none of the constitutive behaviour criteria used predicted the observed underground failures correctly, the extension strain criterion gave the best agreement.

Jan 1, 2007

By L. L. Godirilwe, and A. Shibayama, G. Danha, K. Haga, Y. Takasaki

Selective extraction through leaching of an amorphous slag obtained from a base metal smelter plant in Botswana is investigated in this paper, where the main objective is to optimise the experimental variables that would result in the maximum selective extraction of the three base metals (Ni, Cu and Co) from the slag waste. Mineralogical tests showed that the sample is composed mainly of fayalite (Fe2SiO4), with a total entrapped metal sulphides content of about 1.0 wt.% occurring as fine occlusions in the fayalite phase. In our experimental program, we compare the effectiveness of two common leaching techniques. In the first method, we use sulphuric acid to carry out atmospheric beaker leaching tests, and in the second method we use high pressure oxidative leaching. The effects of acid concentration, oxidant addition/oxygen partial pressure and pulp density on metal dissolution rate are examined. The optimal Ni, Cu, Co extractions of 80.5%, 81.9 and 98% respectively were obtained under high pressure oxidative leaching conditions (150 oC, 0.6 M H2SO4, 0.5 MPa O2), with substantially low dissolved Fe of 9.6%, the majority of which was removed as jarosite in the residue. Atmospheric beaker leaching yielded poor extractions of Ni below 40% when sulphuric acid combined with hydrogen peroxide (1.0 M and 0.6 M respectively, 65 oC) were used for leaching, while Fe, Cu and Co dissolutions were each about 80%. Therefore, using high pressure oxidative leaching provides a possibility to effectively extract Ni, Cu and Co while producing an environmentally benign residue, thus alleviating the current adverse environmental issues associated with the abandoned smelter slag. Keywords: Slag, amorphous, fayalite, atmospheric beaker leaching, high-pressure oxidative leaching, extraction

Jan 1, 2020

By C. Dorfling, M. Tadie, M. Tucker

Electrowinning is the final step in the hydrometallurgical production of high purity copper, involving the passage of electric current through an electrolyte and consequent plating of solid copper to form cathode sheets. Key electrowinning performance indicators are the current efficiency, specific energy consumption, yield, and quality of the metal. The high energy demand and associated cost mean that determination of performance indicators is critical during operation, but ‘online’ measurement is impractical due to the nature of the measurements and corrosive environment brought about by acid mist. This research considered the development of a predictive electrowinning model as a shift towards a pre-emptive approach to attaining plant performance data. A steady-state model was created from input variables available in the industry, using a first-principles approach combining mass balances, electrochemical and thermodynamic equations, and property correlations. A circuit diagram equivalent of an electrowinning cell, containing multiple pairs of electrodes, was used as the backbone of the model. The kinetics of each electrochemical reaction were modelled including iron as a major impurity. Losses in current efficiency due to ineffective electrode contact, short circuits, and stray currents were also incorporated. The model was used to predict the current efficiencies for tests performed at varying conditions in a bench-scale electrowinning cell; the average absolute error between the measured and predicted current efficiencies was 3.2%. The model requires a unique parameter fitting approach for each industrial operation; if parameters are customised for specific plants, the model will be a useful tool to predict performance and can aid the development of effective process control systems in copper electrowinning tank houses. Keywords: Copper; current efficiency; electrowinning; modelling; plating rate

Jan 1, 2020

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By J. A. Maritz

Since the dawn of mining, pillars have been used as primary support to ensure stable workings. Early designs were based on trial and error, after which more scientific means developed over time. A vast amount of progress has been made, especially in soft-rock room-and-pillar design methodologies, from which hard-rock design theories developed with minor changes to constant parameter values. The commonly used Hedley and Grant method for hard rock and Salamon and Munro methodology for soft rock draw on the tributary area associated with the pillar, the width-toheight ratio of the pillar, and a back-analysed strength reduction factor. In these methods, only the vertical stress, or stress normal to the pillar influences the load applied to the pillar. This investigation considers the possible influence of shear stresses on pillars in a room-and-pillar layout in single reef planes and multi-reef environments, based on elastic numerical modelling methods. The possible shear stress poses a safety and financial risk to the design process, whereby an undersized pillar would lead to unstable working conditions, whereas oversized pillars could lead to an under-utilized ore resource.

Jan 1, 2014