Search Documents

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By G. Dhakal, J. -I. Kodama, K. Neaupane, T. Yoneda

ABSTRACT Durability tests and evaluation of sub-zero temperature effects to some argillaceous clastic rocks were carried out. Welded tuff, limestone, sandstone and schist samples collected from different parts of Japan were tested and results are presented. Schist and dolomite from Ganesh Himal area along the higher Himalayas of Nepal were also tested, and the results are compared. The slaking tests were performed on all samples in pure water. The results reveal that the slaking index of schist from Japan is lower than that of schist from Nepal. Regarding carbonate rocks, the slaking index of limestone from Japan is higher than that of dolomite from Nepal. A tendency of decrease in slake durability with an increase in porosity is also observed. Freezing and thawing experiments conducted on welded tuff and schist reveal that crack initiates earlier but extends slower in schist than in welded tuff. It is also observed from the freeze-thaw experiment that the welded tuff deteriorates and wears faster than the schist. However, sandstone remains relatively intact for a long run of freeze-thaw cycles. Zusammenfassung Beständigkeitstests sowie die Bewertung der Auswirkungen von Minusgraden auf Tonschiefer Trümmergestein wurden durchgeführt. Dabei wurden geschweißter Tuff, Kalkstein, Sandstein und Schiefer aus verschiedenen Gebieten Japans sowie Schiefer und Dolomitgestein aus dem Ganesh Himal Gebiet, dem höheren Himalaya Nepals, untersucht und die Resultate verglichen. Für alle diese Gesteine wurden Slaking-Tests in reinem Wasser vorgenommen. Die Resultate zeigen, dass das Slaking von Schiefer aus Japan höher als das von Schiefer aus Nepal war, wohingegen bei kalkhaltigem Gestein das Slaking von Kalkstein aus Japan niedriger als das von Dolomitgestein aus Nepal ausfiel. Es wurde dabei auch eine Tendenz zur Löschbeständigkeitsverringerung bei gleichzeitig erhöhter Porosität beobachtet. Gefrier- und Tautests an geschweißtem Tuff und japanischem Schiefer zeigten, dass Risse in Schiefer schneller auftraten, aber sich langsamer ausweiteten als in geschweißtem Tuff. Bei Gefrier- und Tautests wurde ebenfalls beobachtet, dass geschweißter Tuff schneller verfällt und verschleißt als Schiefer. Sandstein hingegen blieb über lange Tau- und Gefrierzyklen intakt Résumé Des tests de solidités et l’évaluation de l’effet des températures en dessous de zéro sur les rocs argileux ont été effectués. Les rocs d’origine volcanique (cendre), les rocs calcaires, sableux et les schistes de différentes régions du Japon, ont été étudiés. Les schistes et les dolomites de la région de Ganesh Himal le long du haut Himalaya (Népal) ont été étudiés et comparés à ceux du Japon. Les tests de désintégration sur les rocs ont été effectués dans l’eau pure. Les résultats montrent que l’index de désintégration des schistes du Japon est inférieur aux schistes du Népal. En ce qui concerne les rocs carbonyles, l’index de désintégration des rocs calcaires du Japon est supérieur à ceux des dolomites du Népal. Une décroissance de la résistance à la durabilité est observée avec une plus grande porosité des rocs. Les tests de congélation-décongelation sur les schistes et les rocs d’origine volcanique (cendre) du Japon montrent une apparition précoce des fissures mais l’expansion des fissures est plus rapide dans les rocs volcaniques. Des tests similaires montrent que les rocs volcaniques (cendre) se désagrégent plus rapidement que les schistes. Cependant, les rocs sableux restent intacts après plusieurs cycles de congélation-décongélation.

Jan 1, 2003

By GA Harrison

The introduction of Extra Low Profile (XLP) mechanised equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations to achieve injury free sustainable production and cost effective mining technologies. The method allows for the introduction of a suite of XLP and Low Profile (LP) equipment in a narrow reef (1,2m) mining environment. For the first time it is now possible to achieve total trackless mechanisation at these stoping widths and XLP Breast mining has the potential to add more value when benchmarked with conventional mining and other mechanised methods. Various types of XLP equipment were tested at different sites within Anglo Platinum and this paper describes the XLP equipment evolution to-date. It concludes with recommendations on our future strategy regarding implementation and roll out of the XLP technology within Anglo Platinum.

Jan 1, 2008

By M. L. Baharani

Looking for an idyllic paradise that has investment and business potential as spectacular as the stunning views of mountains, the rich Ganesh Himal zinc-lead deposit exposed between 4,050 m and 5,000 m is the answer. Arising from the sea floor in a span of 55 million years, the enchanting Himalayas had remained one of the most potent factors influencing the Asian region. The challenges of the mighty Himalayas notwithstanding, it continues to provide opportunities for the humankind in optimum usage of the natural resources and sustainable development. Optimal management of natural resources in mountain areas through decision support tools offered by remote sensing will go a long way in realization of the Ganesh Himal Zinc-Lead Project. The authors have a real life endeavor spanning over 37 years in developing a mining industry in a mountainous region of Nepal and an attempt to integrate with the development of other natural attributes of the region. With rapid acceleration of science and technology, humankind has acquired power to transform his environment countless ways and on an unprecedented scale. While mineral resources are the pillars on which we have built industry and infrastructure, industrial countries in the North have been in the forefront of technological advancements, the developed countries of the South have been at the receiving end of exploitation of mineral resources worldwide. A relationship with natural environment, re-crafted by the civilizing impulse, to meet human demands are upcoming challenges for management of natural resource in sustainable manner for a livable world.

Jan 1, 2008

By T. C. Alex, K. M. Godiwalla, R. K. Jana

Manganese nodule, available in ocean beds, is a potential resource of the future for copper, nickel and cobalt. Recovering only these metals, containing less than 3% by weight, will result in the generation of large amount of residue. In addition to the material losses, several environmental and ecological problems arise out of this. The present study has been aimed at reducing the environmental and ecological problems associated with massive generation of this residue together with utilization of the resources. Presence of ~ 20% manganese and ~16% silicon in the residue has prompted us to check its suitability as a raw material for silicomanganese production. Lower manganese content and lower Mn/Fe ratio of the residue than that required for silicomanganese production has been corrected in this study by suitable blending. The efficacy of blending and its thermodynamic aspects using FACTSAGE software are discussed. The studies conducted indicate viability of bulk utilisation of the residue through silicomanganese production and thereby reducing the burden on environment to a great extent.

Jan 1, 2007

By G. Wu, S. Liu

In view of the singleness of traditional methods about international petroleum (Brant) price forecast, ten main factors that affect international petroleum price are fully analysed. Based on time series method and multivariate linear regression method, the simulation model with the theory and idea of system simulation is firstly established. And this forecasting system realizes visual operation under the environment of MATLAB/SIMULINK. So this article tries a new way for further exploring petroleum price’s running law and guiding its forecasting practice. Keywords: Petroleum price forecast, system simulation, residual error, physical flows information flows

Jan 1, 2003

By J. Hadjigeorgiou, G. Knox

There is a considerable wealth of information on the behaviour of rockbolts under axial loading conditions both in situ and under controlled laboratory conditions. However, there is comparably less data on the behaviour of rockbolts in shear. Several authors have contributed to the understanding of the behaviour of conventional rockbolts’ performance under shear loading. Much of this data have been gathered through experimental programmes conducted on sections of the rockbolt. Considering the continuous coupling between the rockbolt and borehole interface, the approach is justified. Due to the design premise of energy-absorbing rockbolts with discrete couplings, full scale testing is required to quantify the behaviour of the rockbolts. This paper reviews published results obtained from two testing facilities, which are the SINTEF rockbolt pull test rig in Trondheim, Norway and the Epiroc Combinations Shear and Tensile test rig in Johannesburg, South Africa, both capable of conducting full scale testing of rockbolts. Based on this high-quality database it was possible to identify three distinct responses of rockbolts in shear. The behaviour under load is controlled by the presence or absence of an encapsulation medium (resin/cement grout), the reinforcement mechanism, and whether the rockbolt is continuously or discretely captured. As a reference the results are compared to the performance in shear of conventional grouted rockbolts.

Nov 24, 2025

By B. Z. Weiss, N. R. Comins, F. Blum

The effect of microstructure on the deformation and fracture properties of 3CR12 steel was investigated at different strain rates in the temperature range -196 to 200°C. The yield stress of the as-received steel, showing a banded dual-phase microstructure, was much lower than that of the flake-like dual-phase microstructure produced by heat treatment. The heat treatment also resulted in an increase in the volume fraction of martensite. The fracture toughness of the as-received 3CR12, on the other hand, was significantly higher than that of the heat-treated material. These changes in both yield stress and fracture toughness were attributed to the effect of microstructural parameters on the constraints imposed on the deformation and subsequent failure of the ferritic phase in the as received and heat-treated steels. The exceptionally low resistance to crack extension in a plane parallel to the roiling plane of the as-received material was ascribed to the delamination process, which is typical for controlled-rolled steels. The yield stress and fracture toughness were found to depend on temperature and strain rate. The appearances of the fracture surfaces were found to be consistent with the mechanical properties.

Jan 1, 1992

An investigation into the stability of large open stopes at Premier diamond mine, Culinan, South Africa, is described. The open stopes are located in a weak kimberlite orebody, directly underneath a 75 m-thick sill of gabbro. Two and three-dimensional stress analyses were carried out in a back-analysis of the stresses and failure around the first open stope created under the sill. The results were used in the prediction of the future stability of the planned open stopes, intervening pillars, and sill.

Jan 1, 1987

This publication is provided on an "as is" basis without warranties of any kind, either expressed or implied including, but not limited to warranties of title or implied warranties of merchantability of fitness for a particular purpose. The information contained in this publication is for general information purposes only. It does not constitute professional, technical, financial or other advice to the user of this publication and must not be relied upon as such by any person whatsoever. The use of this publication is at the users own risk. The authors/creators of the information contained in this publication have tried to ensure that the information contained herein is correct, but errors or inaccuracies may exist or the information may be incomplete, unreliable or no longer up to date. Therefore, no warranties of any nature whatsoever are given and any liability to any person in respect of anything and in respect of the consequences of anything done or omitted to be done, wholly or partly in reliance upon the whole or any part hereof, are disclaimed, including and without limitation any contractual, dialectal, direct, consequential or financial damages or losses. On no account will Organisers and/or any of the contributors or any person or entity involved in creating, producing or distributing the information and or software available in this publication be liable for any such damages arising out of the use of or inability to use this publication. Copyright Reserved The South African Institute of Mining and Metallurgy P O Box 61127, Marshalltown 2107, South Africa www.saimm.co.za All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without the written permission of the copyright owner. Although the greatest care has been taken in the compilation of the entire contents, the editors and publishers do not accept responsibility for errors or omissions. First Edition Copyright February 2004 Proceedings ISBN: 0-9584663-5-1 (1 volume and CD-ROM)

Jan 1, 2004

Mineral sand beneficiation plants comprise a complex combination of electrostatic, magnetic and gravity based separation techniques. These are combined and replicated in ways that provide the most efficient and cost effective separation of the valuable components. On line instrumentation has been developed at the JKMRC (eg. conductor/non-conductor(CNC) ) to measure the properties of the dry plant process streams. This paper provides results from the recent development of a novel low cost mass flow meter and discusses their combined use with the CNC instrumentation for the control of dry separation circuits.

Jan 1, 2003

By A. Della Rocca, P. Jonker, B. Henning

Successful prediction of the collection efficiency of cyclone separators is a necessary step in cyclone design and verification. Aside from standard empirical relations, CFD modelling is widely adopted to supplement the design of cyclone units in relation to the desired separation performance. Nevertheless, effective adoption of numerical modelling is sometimes prevented by large modelling errors, especially for small size particles which are more subject to turbulence effects than larger particle classes. In the past, this motivated the adoption of more refined turbulence modelling approaches, such as large-eddy simulations. These approaches provide greater insight into time dependent behaviour, while leading to larger computational cost with respect to more standard approaches. In this paper, an effective Eulerian-Lagrangian Reynolds-averaged Navier-Stokes (RANS) approach is investigated, which is able to predict the complete separation efficiency curve with satisfactory accuracy, without requiring prohibitively long computational times. An assessment of the proposed approach is carried out against experimental data from large laboratory scale cyclones, in the form of mean and fluctuating velocity profiles from LDA measurements (Hoekstra, 2000), as well as with respect to the experimental separation curve (Zhao, 2005). The final application to a full-scale industrial cyclone unit is then carried out with the aim of tuning the cyclone design to the separation efficiency curve as required by downstream processes. Keywords: Cyclones, separation, CFD, RANS, RSM, Lagrangian

Jan 1, 2020

By S. Purushotham, Y. R. Murthy, M. Narasimha, S. K. Tripathy, M. Kumar

Spiral concentrators are gravity-based separators widely used to beneficiate coal, heavy minerals and beach sand. It consists of a helicoid trough that spirals downward in the helical configuration around an axial column. The particle segregation takes place based on size and density under the influence of gravity as the particles spiral down within the thin water layer. In the last century, most design modifications of this equipment were based on trial and error based lab-scale experimentations and empirical approach. The use of Computational Fluid Dynamics (CFD) has gained interest in the past two decades to understand the underlying flow physics in the spiral concentrators. In this paper, we used CFD to model the fluid flow and investigate the particle segregation inside a conventional LD9 spiral concentrator. Firstly, the Volume of Fluid model was used to resolve the liquid-air interface. The liquid depth and flow field predictions for varying flowrates were validated against the experimental literature data. One-way coupled VOF-LPT model was then used to describe the particle dynamics in the spiral flow field assuming dilute particulate flow. Moderate dense particulate flow (20 vol.%) was then modelled using the Algebraic Slip Mixture (ASM) model. Four particle-phases representing particles of different sizes of dual-density were simulated, and the component particle segregation was analysed. Keywords: Spiral concentrator, two-phase flow, multiphase, discrete phase model, ASM model

Jan 1, 2020

By D. G. Hulbert, D. J. Oosthuizen, D. de V. van der Spuy

Expert Online, as a software system, is aimed at providing plant operators in the minerals industry with effective training and on-the-job assistance. It incorporates a number of features to achieve this goal, of which the most important is its ability to explain the dynamics of the plant and control system in simple language, mimicking an informed plant expert who has online access to the inner workings of the plant and control system. This is made possible by a novel form of Artificial Intelligence, called the Interpreting Expert System. Previous implementations of the IES were only capable of explaining controller actions. Expert Online will extend this capability to also perform the more difficult task of explaining process behaviour. Expert Online will implement three main processes, namely the accumulation of data from the controllers and plant models, the interpretation, processing and filtering of that data and lastly communicating the relevant information to the user, both as written messages and in other audio-visual forms. Although Expert Online is aimed at the operator, other plant personnel, like supervisors and plant managers, will also benefit from it. This paper focuses on the structural and functional design of Expert Online for implementation on the latest version of Mintek’s open control platform, PlantStar, highlighting advances and additions since the previous implementations of the Interpreting Expert System and concluding with an example illustrating some of the principles.

Jan 1, 2003

By K. Wu, L. Li, D. W. Zhou, J. W. Yu

The presence of a fractured water-conducting zone (FWCZ) is of significant importance for the safety of underground mining under water bodies. When a coal mining area is covered with a thick layer of alluvial soil, the height, width, and distribution pattern of the FWCZ in the area shows unique features. The internal mechanism by which thick alluvial soil affects the FWCZ is still unknown. Using the Huainan coal mining area (HCMA) in China as a case study, we investigated the impact of thick alluvial soil on the height, width, and distribution pattern of the FWCZ through numerical simulation using the distinct element method, theoretical derivation, and data validation. The results indicate that a thick layer of alluvial soil inhibits the FWCZ height and increases the FWCZ lateral width. When the soil-to-rock ratio is greater than a certain value (the numerical result in this study is 15:18), the FWCZ height and width are affected by the thick alluvium significantly, and the thick alluvial soil alters the shape of the FWCZ from tall and thin to short and wide. The load exerted by the alluvial soil transfers downward to influence the FWCZ; however, this process is obstructed by the hard strata in the bedrock. Therefore, the vertical and lateral change trends show a similar step pattern. Our results can provide a basis for accurate calculation of the FWCZ height in mining areas with thick alluvial soil, to mitigate mine water hazards and increase the safety of underground mining in coal mines covered with a thick alluvium layer. Moreover, reducing the FWCZ height can help extend the upper extraction limit in coal mines covered with a thick alluvium layer, which reduces the thickness of the impermeable coal pillar and increases coal production.

Jan 1, 2016

By J. H. Bulloch

The paper gives an assessment of the available data on the linear elastic fracture mechanics involved in stress corrosion cracking and in the behaviour of reactor pressure-vessel materials exposed to a simulated pressurized water-reactor environment. As a result of the different experimental techniques used in the various studies mentioned, only a few detailed conclusions can be drawn. The data from constant-displacement wedge-opening loading (WOL) tests, with the exception of one study, exhibited very limited or no crack extension during exposure periods of up to 14000 hours. The data from constant-load tests indicated evidence of crack extension, but the nature and extent of the crack extension are still unclear. When crack extension did occur, it was exclusively transgranular in nature. Certain differences in the available test data are tentatively explained in terms of the experimental procedures used, and the need for a consistent code of experimental techniques is highlighted.

Jan 1, 1987

By F. Crundwell, A. J. Lathwood

A number of base-metal operations would like to increase production to take advantage of the higher metals prices. In general, this higher production should not be achieved with major operating changes. In hydrometallurgical facilities, leaching and pressure leaching represents one area where upfront limitations may be a bottleneck to the capacity of the entire plant. An assessment of the capacity of the leaching tanks and autoclaves was performed using a predictive model within the AweSym flowsheet simulator. The model is described, and the results of the application of the model to a number of different leaching reactors are presented. It is argued that the leaching number, which relates the residence time, particle size and the leaching rate, is of prime importance. Finally it is shown that there are some unexpected catastrophic events in increasing production capacity without a thorough understanding of the leaching operation.

Jan 1, 2007

By H. A. D. Kirsten

The effects of the mining of deep-level tabular reefs are usually evaluated by use of continuum, elastic mining simulation analyses. This paper gives the results obtained from a series of analyses in which stopes of limited span are considered to be excavated in a non-linearly non-elastic, jointed and fractured rockmass. In particular, the theoretical influence of soft backfill in these conditions is evaluated. It is shown that the stress distribution and behaviour of the rockmass, alternately taken as an intact-elastic and as a fractured non-elastic medium, are completely different. The relevance of the energy-release rate commonly calculated in mining-simulation analyses, and the efficacy of its correlation with seismicity and the associated rockbursts, are reviewed. In deep-level mining operations, it is not practically feasible to obviate releases of seismic energy. The fact of their occurrence should therefore be accepted and, rather than considering the reduction of energy release as the primary objective, efforts should be concentrated on minimizing the effects of such release. Analytical results are given to demonstrate that this approach is not only correct, but also the only feasible solution to the rockburst-seismicity problem in deep mines.

Jan 1, 1989

By R. J. Forzatti

The production of sulphuric acid from sulphur generates heat. The majority of this heat is recovered as steam and is often used to generate electricity. Heat not recovered as steam is rejected to cooling water systems. The design of the turbine, condenser, and cooling water systems impacts the overall water, energy, and environmental footprint of the plant. This review considers a conceptual 2000 t/d sulphuric acid plant with several alternative cooling water systems. The review utilizes Hatch?s 4 Quadrant sustainable design tool to compare the alternatives on both an economic and a weighted sustainability scale.

Jan 1, 2014