Search Documents

The head loss data for coal slurries over a range of concentrations and velocities and the laboratory screen analysis were selected as areas for investigation in the data analysis performed. The analysis resulted in the following: (1) Size distributions for the coal used in the horizontal pipeline tests were fitted to the Rosin - Rammler distribution function. Each of the fits was significant. Corresponding Rosin - Rammler parameters were obtained which were introduced into the regression analysis. (2) A regression equation was obtained which predicts the slurry head loss of 1-inch by 0 coal slurries ranging in volumetric concentration from 20 to 40 percent and line velocities from 1 to 14 feet per second as a function of the square of velocity. The addition of the term for concentration in the regression equation did not contribute significantly c head loss.

Jan 1, 1972

By Henry G. Dorsett

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 73 chemical compounds and mixtures, 29 drugs, 27 dyes, and 46 pesticides. Information is given on ignition temperatures of cloud and layer, minimum igniting energy, minimum explosive concentration, percent of inert dust required to prevent flame propagation, limiting oxygen concentration in the atmosphere to prevent ignition, and pressures and rates of pressure rise at dust concentrations of 0.1, 0.2, 0.5, 1.0, and 2.0 ounces per cubic foot. Explosibility indexes are computed where data are available to permit comparison of the relative explosion hazard. Variations of explosibility parameters with chemical composition are discussed. General means for minimizing the dust explosion hazard are reviewed.

Jan 1, 1968

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph'ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By F. E. Wormser

"Arsenic has been recently quoted at 10 1/2 - 11 cents per pound, an increase over the prevailing price of last fall, when arsenic was cents, as against pre-war prices around 4 cents is evidently a sustained demand for this material. The following statements are intended to summarize briefly some particulars regarding arsenic.Commercial arsenic is the white arsenious oxide (As203). This is the form in which it is generally marketed, as the uses of arsenic demand its industrial application in this form. Arsenic as an element finds rather restricted use in the hardening of lead shot, ere it is to some extent replacing the use of antimony, while white arsenic is employed in a variety of manufacturing processes, chief of which is the manufacture of insecticides and sprays. The poisonous nature of most arsenic compounds, the commonly known ones being paris green and lead arsenate, and its relative cheapness, make arsenic a material suitable for this purpose. The stimulation of agriculture during the war greatly increased the demand for arsenical insecticide. Glass making consumes a large amount of arsenic as it has been impart increased brilliancy to the glass. Crude commercial arsenic is often used to kill weeds along railroad tracks. Arsenious oxide is used also for preserving hides, while the disulphide, AS2S2), finds an application in dehairing hides for the finest grade leather, as it least affects the product. Orpiment (As233), is used in textile dyeing. Wall paints and wall paper formerly consumed considerable arsenic in the form of paris green, but this use has been largely,given up due to the poisonous nature of the dust from the product. Sodium arsenate for a similar reason, is now little used in printing where it had found application. The great objection to arsenical yes and paints is the risk of poisoning from use of the manufactured article. Sodium arsenite is the principal poisonous in¬gredient of many cattle and sheep dips. Arsenic compounds are also used medicinally."

Jan 1, 1920

By William H. Pomroy, Annie M. Carigiet

This U.S. Bureau of Mines publication is an analysis of underground coal mine fire incidents occurring in the United States during the 15years from 1978 through 1992. The fire data used in this analysis were obtained from U.S. Mine Safety and Health Administration mine fire investigation reports. Fires were analyzed by year, State, coalbed thickness, mine size, mining method, ignition source, burning substance, location, equipment involved, detection method, time of day, time of year, number of injuries and fatalities, method of extinguishment, and evacuation measures taken. In all, 164 fires are included in this report, or an average of 10.8 fires per year. The most fires occurred in West Virginia, Kentucky, and Pennsylvania, respectively. However, the fire incidence rates for these States, expressed as the number of fires per million tons of coal mined, were the lowest, second lowest, and fourth lowest of all underground coal producing States. The most common ignition source was electricity; the most common burning substance was coal; the most frequent fire location was the belt entry; the most common equipment involved in fires was the conveyor belt; and the most common extinguishing agent was water.

Jan 1, 1995

By M. M. Tilman

The Federal Bureau of Mines developed a rolling method that improves creep resistance and yield strengths of lead alloys containing up to 5 wt-pct Sb. The 0.69-inch-thick slab-cast alloys were breakdown-rolled to 0.226 inch and finish-rolled to 0.063 inch at 5-or 20-pct reduction per pass. Rolling was at room temperature to simulate conventional cold rolling, and at 75°, 125°, and 175° C. Two alternative methods evaluated consisted of (1) a single cold final pass followed by annealing and (2) a single hot final pass. Two additional processing methods involving percipitation strengthening were included for comparison. Compared with conventional cold rolling, hot rolling at 125° and 175° C with multiple light passes vastly improves creep resistance and raises yield strengths. Tensile strengths are less affected. The other treatments also improve creep resistance significantly and generally improve tensile properties; magnitudes vary with treatment and composition.

Jan 1, 1975

By D. D. Dornenburg

The effect of changes of atmospheric pressure on methane emissions from extensive worked-out areas of coal mines in several Midwestern States has lone caused concern to State and Federal mining departments, as well as to the operating companies involved. Common mining and ventilation methods employed in mines in these States have resulted in large sealed and unsealed worked-out areas in which considerable quantities of methane are emitted alone both intake-and return-air courses. The common practice is to watch barometric changes very closely and take special precautionary measurer during periods of low barometric pressure. Although the hazard is recognized, mining officials have different opinions concerning the effect of barometric pressure variations on the emission of mine gases. These opinions are based upon scattered personal observations, as no records exist of actual studies to establish such effects.

Jan 1, 1955

Case 1: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ] Case 2: A crew was preparing to remove a pump from a well when the hoist boom contacted a 4160-volt power line. The hoist operator was electrocuted. [ ]

Jan 1, 2005

By J. S. Tosh

An equilibrium study of the system potassium carbonate, potassium bicarbonate, carbon dioxide, and water has been conducted with solutions of 20-, 30-, and 40-percent equivalent potassium carboaate concentrations. These equilibrium data cover the operating range of the hot carbonate scrubbing system for removing carbon dioxide from gas mixtures. Such data are necessary to establish the limits of purification and are used to design absorption and regeneration towers. Values of K in the relationship K = (KHCO3)2/(K2CO3)PCO2 were determined for higher temperatures of 70" to 140° C. and greater concentrations, I 20 to 40 percent, than employed by previous investigators. For the 20- and 30-percent concentrations, K is constant at a given temperature; thus, once K has been determined the equilibrium pressure of carbon dioxide can be calculated for any conversion. Variation of & values with changing conversion was observed with the 40-percent solutions, so that equilibrium calculated pressures are less reliable from average K values.

Jan 1, 1959

By Takashi Ohya, George V. Keller, Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a rela- tively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurements of ambient surface electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal-to-noise ratio at the surface. Numerous C.W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surface magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null in the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

By W. P. Diamond, John C. LaScola, D. M. Hyman

In 1972, the Bureau of Mines developed a direct-method test for measuring the gas content of virgin coal core samples for coal mine health and safety considerations. Since that time, approximately 1,500 coal samples from more than 250 coalbeds in 17 States have been collected for gas content determination. The gas content data, when combined with geologic and engineering studies, can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if methane drainage in advance of mining should be considered. The data are also critical in delineating coalbed methane resources and in utilization feasibility studies. This report makes the Bureau's extensive data base of gas content data more readily available to the coal and gas industries. The data are presented in tabular form, alphabetically by coalbed name and by State. The components of the total gas content (lost, desorbed, and residual gas) are given, Location (State and county), sample depth, coalbed or formation name, and coal rank are included for geographic and geologic identification.

Jan 1, 1986

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

By W. R. McDonald

The Bureau of Mines, U.S. Department of the Interior, conducted small-scale field tests on acidic copper tailings as part of its effort to develop, improve, and demonstrate technology for stabilizing mining and mineral-processing wastes. Two successful demonstration revegetation plots were established on an abandoned copper-tailings pond located on public land adjacent to Holden Village, Wash. The tailings were neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Excellent plant growths covering 70 and 24 percent of the surface were achieved on 1/8-and 1-1/2-acre test plots planted in 1973 and 1974, respectively. Regar brame, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. The target pH of tailings neutralization was 6.8; however, good plant growth occurred in areas where the soil pH ranged from 2.9 to 5.8.

Jan 1, 1978

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By S. P. Howell

The Bureau of lines as repeatedly called attention to dangerous practices in the transportation and opening of kogs of black blasting powder. In 1914 Diwin Higgins (Prevention of Accidents from Explosives in Metal inos, Miners' Circular 19, Bureau of Mines, p. 15) stated "canisters should always be opened by removing the bung. To use a pick or other sharp tool for cutting a hole in the canister is dangerous. After the necessary amount of powder has boon taken out, the canister should be kept closed. The powdor should always be handled at a safe distance from an open light." In 1919, Geo. S. Rice (onthly Statement of Coal line Fatalities for June, 1919, Bureau of Mines, pp. 16 to 18) calls attention to the dangers that arise in underground transportation and handling of explosives, and calls special attmtion to the danger of hauling explosives in motor trips; the unnecessary risk involved in hauling men on the trip at the same time, and the necessity of keeping open lights away from black blasting powder. In 1919 the writer (Sensitiveness of Explosives to Frictional Impact, Tech. Paper 234, Bureau of Mines, pp. 13, 15) called attention to the fact that black blasting powder is not as sensitive to frictional impact as the nitro-glycerin dynamites and the gelatin dynamites. Black powder may be ignited by direct impact and the writer believes that this may occur without presupposing a preliminary spark. It is well known, however, that black blasting powder is very sensitive to ignition by spark flame, or heated materials, and these may be produced by an electric current, by an open light, by incandescent particles from a pipe, cigar, or cigarette, by the tearing of metal sheets or scraping of metal against metal, and possibly, by other means. -- The above discussion will serve to introduce a newly recognized hazard the ignition of black blasting powder by the forcible opening of kegs with wodden tools. The details of three accidents in which kegs of black blasting powder ex- ploded instantly when a wooden tool was driven forcibly through the top of the kegs are as follows: 1. In 1915, a powder man employed by a coal mining company stated that he was opening a 25-pound log of black blasting powder by driving a hole in the top with a wooden sprag when the powder in the leg ho was opening ignitod. This caused the ignition of fifty-two additional 25-pound logs of the powder, and the fatal burning of this and another powder man. The ono making this statement lived five hours after the explosion.

Sep 1, 1920

By A. E. Wells

"When the United States entered the World War, the heavy requirements for sulphuric acid in the manufacture of explosives made necessary a definite knowledge of the sulphuric acid capacity of the country. The Bureau of Mines, under the authority conferred by the explosives regulation act, made a thorough survey of the sulphuric acid situation. In this work, which was personally directed by the writer, comprehensive data were collected on the situation and capacities of the various acid plants, sources of supply of raw materials (brimstone, pyrite, pyrrohotite, zinc ores and concentrates, waste sulphur dioxide gases from copper smelting, and spent oxide from gas works), the principal points in regard to manufacturing processes (chamber and contact) and the uses of the acid. The results of this investigaion have recently been published by the Bureau of Mines, as Bulletin 184, entitled ""The Manufacture of Sulphuric Acid in the United States"" by A. E. Wells and D. E. Fogg. The following paragraphs on the uses of sulphuric acid are abstracted from this bulletin.Sulphuric acid is one of the most important of all chemicals, not only because of the large quantities manufactured but also because of the wide use of the acid in many different industrial works. Sulphuric acid is to the chemical industry what iron is to metallurgy. The general public, however, does not realize this fact, for sulphuric acid does not appear in the finished product as does iron and steel, but is only a means to an end. It is essential in many industries, such for example as in the manufacture of phosphate fertilizers, explosives, dyes and petroleum products. In recent years in the United States, especially in the East, the demand for sulphuric acid for chemical and metallurgical industries has been an accurate and sensitive barometer of the general business conditions. This demand for acid responds much more quickly to a general slump or boom in the industrial world than does the demand for iron and steel."

Oct 1, 1920

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969