Search Documents

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900's and was surface mined in the 1940's. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

By Jeffery L. Kohler, Harvinder Singh, Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 2, 1981

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude oils from producing fields in the United States and has published a series of reports on different fields, including oil fields of Texas3. Production Data The Spindletop field was discovered in 1901 when the pay sand was found at deaths of about 800 feet. During the following twenty-five years a number of attempts were made to find a deep productive sand. All attempts sere failures until a roll drilled by the Yount Lee Oil Company found oil late in 1925. An intensive drilling campaign began at once, and the production of the Spindletop field increased to a daily average of 93,217 barrels in September, 1926; the present production is estimated at 66,000 barrels doily. Tile following table taken from the Oil and Gas Journal for February 10, 1927, shows the daily average and the total production by ninths for 1926.

Jan 1, 1927

By James E. Bell

Quartz crystals occur on a farm in the vicinity of Laurel Fork, Carroll County, Va., in abundance over a large area, This has been known for several years, but no work had been clone, up to the Bureau of Mines examination in 1943, to determine the amount of crystalline quartz of usable quality. Field exploration was undertaken throughout the month of June 1943.

Jan 1, 1950

By W. J. Wenger

Analytical, geographical, and geological data on 67 samples of crude oils from Utah are presented, along with some correlations and interpretations. Most of the, geologic formations that produce oil in other areas are also productive in Utah; and as in many other locations, the Permian, Pennsylvanian, and Mississippian formations account for the major amount of the total oil produced in the State. Some anomalies and unusual phenomena are noted. Although most Utah oils are low in sulfur, a sample containing the highest percentage of sulfur ever recorded by the Bureau of Mines is among the oils discussed in this paper. Most of the oil from the major producing formations in Utah is low in sulfur; the same formations produce high-sulfur oils in adjoining Rocky Mountain States. Some Utah oils are both waxy and asphaltic, an unusual combination of characteristics. Correlation index curves for some oils are shown suggesting compositional differences in oils from different producing formations. Production statistics trace the rapid rise of oil production in the State after the first commercial discovery in 1947 and indicate a decline in amounts produced since 1959, the year of peak production in Utah.

Jan 1, 1971

By R. V. Ramani, P. M. T. White, D. Sutton

Appendix I. Part 1: Description Of Geology & Reserves System Introduction The Ore Evaluation and Reserve programs have been developed to aid in the evaluation of coal deposits, both qualitatively and quantitatively. The "Weighted Moving Average" technique used provides considerable flexibility in dealing with diverse parameters with differing distribution characteristics. Determination of Model Constants "a" and "k" - Unit 1 The flexibility of the method in dealing with diverse value parameter distributions lies in its ability to cater to the individual characteristics of each. These characteristics are embodied in the values determined for constants "a" and "k", namely, local and regional variations in value distributions, respectively. The empirical method used attempts to optimize the "a" - "k" combination. Realistic values for "a" and "k" are entered into the program together with sample values for the required parameters and their respective coordinate location values. All the values within a specified radius from the point being evaluated are used to interpolate a value at that point. (Note, the interpolated point is the location of one of the boreholes, values of which are not used in the calcula¬tion.) 3n a similar manner, interpolated values are calculated for each borehole location and for each parameter. This is done for each possible combination of "a" and "k".

Jan 1, 1974

By G. W. Jones

[One of the mJor c~ctivities of the Bureau ~f l;ine;: is the j.a-onotion of sdetp in mining a.nJ other inclus tries. 13 cor'ncc tlcn td t~l tiiene activities the 3~.sccu r:e termine? t'le cwl.os:lon ha~arls 95 n,o;r.?xs tibla Tases, vzpor s, aid scli3s aqi iavestig~ ter rnrI.?ns of controlling s-~fi. prevpri ting eqlosians.]

Jan 1, 1941

By Allen D. Look

In the prevention of accidents in milling operations, the proper installation and guarding of electrical and mechanical equipment, safe clearances, good housekeeping, adequate fire protection, adequate ventilation, dust and fume control, and good illumination, as well as safe practices, are essential. In the new concentrator of the Magna Copper Co., Superior, Ariz., many safeguards were incorporated and safe practices instituted to minimize accident hazards. The purpose of this paper is to describe some of these features and practices.

Jan 1, 1951

By M. H. Kline, Wing G. Agnew

"INTRODUCTION The Yancey-Crawford tract, located 1-1/2 nines east of Yancey station on the Norfolk & Western Railway in Rockingham County, Va. was from 1917 to 1941 considered an unusually promising manganese prospect. Because of the favorable geologic formations and because of the common occurrence of manganese in the district and Virginia's large production of these minerals from this area, geological report 3/ have listed this tract as the No. 1 prospect in the State. During World War I, extensive geologic studies were made to locate manganese deposits similar to those exploited at the Crimera mine near Waynesboro to alleviate this mineral shortage during the existing emergency.In September 1941 the Bureau of Mines started exploratory drilling on the tract in an effort to discover and block out reserves of manganese minerals as authorized by the 76th Congress under the Strategic Materials Act. After five drill holes wore sunk, the project was terminated October 1941."

Apr 1, 1948

By G. W. Jones

[One of the mJor c~ctivities of the Bureau ~f l;ine;: is the j.a-onotion of sdetp in mining a.nJ other inclus tries. 13 cor'ncc tlcn td t~l tiiene activities the 3~.sccu r:e termine? t'le cwl.os:lon ha~arls 95 n,o;r.?xs tibla Tases, vzpor s, aid scli3s aqi iavestig~ ter rnrI.?ns of controlling s-~fi. prevpri ting eqlosians.]

Jan 1, 1941

By Ronald D. Hill, Elmore C. Grim

To better appreciate the problems associated with surface mining, it 1s imperative that the stripping operation be understood. Surface mining is a very broad term and refers to any process of removing the earth, rock, and other strata in order to uncover the underlying mineral or fuel deposit. Strip mining is a type of surface mining in which the overburden is removed in narrow bands, one cut at a time. Strip mining methods employed to recover coal can be divided into two general types: area and contour.

Jan 1, 1974

By Eliot J. White

The physical properties and clay mineral content of the major oil-producing formations in the Powder River Basin of Wyoming were determined by analyses of cores from 100 wells. Interrelationships were established among permeability, restored water saturation, clay content, and bulk swelling capacity of the crushed sample and used to estimate the susceptibility of the formations to water damage. The ratio of water permeability to gas permeability (kw/ki) offers a convenient scale for semiquantitatively estimating the water sensitivity of sands. The irreducible water saturation was also found to have a similar relationship to the clay mineral content and the water sensitivity of the sands. The average relation of water permeability to gas permeability is different for each sand, as shown by the curves, and the relative positions of the curves indicate the degree of water sensitivity of each sand from which the susceptibility to water damage may be estimated. How accurately these estimates show formation behavior under field operations will not be known until studies of field performance can be made. The water permeabilities of the Muddy, Minnelusa, and Tensleep sands average about the same as the gas permeabilities, and these sands are classified as insensitive. The water permeabilities of the Sussex and Shannon sands, at the other extreme, are much less than the gas permabilities [when average ki is 30 millidarcys (md), kw is 6.1 md], and these sands are classified as highly water sensitive. The sensitivities of the five other sands are between these extremes.

Jan 1, 1962

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By D. A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. H0122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available.

By J. H. Maysilles

The Bureau of Mines is conducting research on various technologies to recover alumina from domestic resources for feedstock to existing aluminum smelting capacity as a means to reduce dependence on imported bauxite, which represents 93 pct of U.S. aluminum requirements. One of the more promising technologies being investigated is the hydrochloric acid leaching of kaolinitic clay. In the hydrochloric acid leaching technology, alumina is recovered from iron-free aluminum chloride leach liquor and separated from impurity elements by sparging the liquor with HC1 gas to crystallize aluminum chloride hexahydrate (ACH). A large-scale crystallizer with a 336-gallon usable volume was constructed and operated to obtain engineering and design data for potential scale up and to demonstrate the ability of the technology to produce specification grade alumina. Test campaigns involving about 1,400 hours of operation were completed. ACH meeting all chemical purity requirements could not be produced by a single crystallization, but was produced by recrystallizing the product from the calcined kaolin clay leach liquor. Product crystals with a size distribution of more than 80 pct plus 100 mesh and 65 pct plus 65 mesh were made at a rate of 10 pounds of ACH/(hr)(ft3). The zirconium tube heat exchanger used to maintain constant process temperature operated with an over-all heat transfer coefficient of 420 to 500 BTU/(hr)(ft2)(°F).

Jan 1, 1981

By G. M. Potter, F. S. Wartman, M. D. Schmid

"In matte smelting of copper it has been established that the sulphpr present will combine with copper as long as the latter is present, and that thereafter it will combine with iron. The Cu-Fe ratio in the matte is determined by the Cu-S ratio, presumably owing to the much greater affinity of copper for sulphur or, expressed thermodynamically, the greater stability of copper sulphide in contact with silicate slag. Now, the work of Fournet and of Schütz, which is quoted in many elementary metallurgical texts, indicates that manganese ranks ahead of copper in its affinity for sulphur. Hence, we might expect that manganese could be concentrated from its admixture with iron. Compounds by matte smelting, and Rotts / has patented such a process. This greater affinity of manganese or sulphur is used to advantage in iron metallurgy, also, in which it is well-known that sulphur will combine with manganese and separate from metallic iron as manganese sulphide. Manganese sulphide,however, is quite soluble in silicate slags. 5/ The loss of manganese in slag in any attempted matte smelting is therefore great.If this solubility of manganese sulphide is slag is a physical one and the reaction MnO + FeS MnS + FeOIs substantially complete, then it might be expected that the addition of copper sulphide, which is almost entirety insoluble in slag, would serve to extract the manganese sulphide with the formation of a manganese-copper matte on the other hand, if an equilibrium exists in the above reaction, a copper sulphide layer would displace that equilibrium in one direction or the other, according to whether iron sulphide or manganese sulphide were more soluble in the matter layer."

May 1, 1937

By Nicholas Kyriazi

A performance comparison of 14 rescue breathing apparatus was undertaken as an assessment of past and present worldwide technology. Rescue breathing apparatus are self-contained, closed-circuit breathing apparatus used for entry into areas having atmospheres that are immediately dangerous to life and health. Apparatus tested were the Biomarine BioPak 45, 60, and 240; the Draeger BG 4 and BG-174A; the Litton LITPAC II; the MSA Custom 4500 II Air Mask, Chemox, and McCaa; the Sabre Selected Elevated Flow Apparatus (SEFA); the Scott Rescue-Pak; the Siebe Gorman Aerorlox and Proto Ten; and the SurvivairLP-120. The apparatus were tested on an automated breathing and metabolic simulator at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH). Physiological parameters monitored during the testing were average inhaled CO2 and O2, minimum inhaled CO2, inhaled wet-and dry-bulb temperatures, and peak inhalation and exhalation breathing pressures. The metabolic demand on the apparatus was 1.35 L O2/min for most of the test with two 5-min intervals of 2.5 L O2/min, the first beginning 10 min into the test and the second beginning 10 min before the end of the rated duration of the apparatus. Results presented include apparatus service life and test-averages of monitored physiological parameters. Schematic drawings and photographs of the apparatus are also included. The Draeger BG-174A and BG 4 had the highest durations—295 and 291 min, respectively. The BG 4 hadthe lowest minimum inhaled CO2 levels, attesting to the effectiveness of its CO2-absorbent canister. The SabreSEFA had the lowest average inhaled CO2 levels, due mostly to the apparently low-dead-space mask andnose cup. The MSA Air Mask, the only open-circuit device tested, had the lowest wet- and dry-bulb temperatures, with the liquid-O2-source Siebe Gorman Aerorlox having the next lowest temperatures. The only apparatus with a CO2-absorbent not in a packed-bed design, the BG-174A, had the lowest exhalation pressures. The BG 4 had the highest level of positive pressure, with the Biomarine BioPak 60, Survivair LP-120, SEFA, and Litton LITPAC II nearly as high. The BG 4 had the lowest pressure swing, with the SEFA a close second.

Jan 10, 1999

By R. R. Backer

The Bureau of Mines investigated the typical physical and chemical properties of coal waste materials from the western part of the United States. The results are compared, in so far as possible, with the properties of waste materials from eastern coal operations. The authors found a disparity of mines and preparation plants among western U.S. coal operations and dissimilarities with typical operations in the East. The relatively cleaner product from the predominance of surface mining and the occurrence of thicker seams in the West reduces the amount of coal preparation required and the size of the waste piles. Because of the abundance of land available for waste disposal, many of the piles are low and extended over large areas. New concepts relating statistical shear strength data to liquifaction potential are presented. The somewhat limited data indicates that western coal sludge is coarser with higher permeabilities and shear strengths than the eastern deposits.

Jan 1, 1977

By Ε. P. YoUNGMAN

This paper presents one of a series of digests of foreign mining legis- lation and court docisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in vericis foreign countries. This interpretation of the laws - of Italy has been prepared, in part, from an aclysis made by John W. Frey, for merly associate mineral economist, U. S. Bureau of Mines. It incorporates addi- tional data and comments offered by Enrico Giobbe Della Pitta, a well-known Italian lawyer, in response to a questionnaire. These comments were forwarded by Harold H. Tittmann, American chargé d'affaires ad interim, at Rome, and trans- mitted to the Bureau of Mines through the courtesy of the Department of State.

Oct 1, 1930

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950